Standart-SZM

Volvo FH 16.750 Globetrotter XL 4x2 - Retarder - I pa...

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2017, yükleme alanı uzunluğu: 10.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 1.900 mm, yükleme alanı hacmi: 50 m³, Chassis light version Aluminium (15-6-12) Two fully automatically welded I-section longitudinal beams with welded cross members. Chassis width approx. 1,600 mm Axles and Suspension Disc brakes 430 mm "Off Road Version" SAF Intradisc axle units 3 x 9 t with SAF air suspension, central air bag arrangement next to the chassis longitudinal beams, 1st axle liftable with drive-off aid and manual forced lowering, Smart Board info center, lift-lower valve, 3rd axle with trailing steering, electrically lockable, Tyres and Wheels 6 wheels fitted with 385/65 R 22.5 tyres, approx. 40-50 % tread remaining, with Alcoa aluminium rims "satin" 11.75 x 22.5 ET 120, UNI-wheel bolts for aluminium rims Landing Gear Mechanical version with single-side operation, 2 speeds, with swing foot for air suspension, 2x20t static load capacity Fpjdpfx Asxf Sn Ijfzor Braking System According to E.C. standards, twin-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E including RSS (Roll-Stability-System), Wabco Smartboard info center, aluminium air reservoir system Electrical System According to StVZO regulations, with 2 five-chamber lamps type Aspöck Ecopoint 2, 24-volt system with 2x7- and 1x15-pin sockets, with lateral outline marker lights, 2 separate LED reversing lights at the rear. All air and electrical lines neatly installed in plastic tubing. Tipping Body/Bin Body, fully welded interior Aluminium bin, side walls made of 30 mm thick plank profiles (2-3 mm), 600 mm wide, welded, floor 8 mm thick high wear-resistant alloy (5383H34/HB 110), bulkhead 4 mm reinforced in straight version, rear wall as double swing doors in straight version with 2 half/half doors each with a grain chute, pneumatic floor vibrators underneath, rear hanger made of aluminium, swing-out, two hold-downs with rubber buffers on the tipper bin attached to the frame at the bulkhead, Hydraulic System Tipping cylinder with "cardan" mounting, 7,630 mm stroke Hydraulic cylinder mounted to the bulkhead, working pressure 220 bar, make Hyva, 220 bar with approx. 2.5 m hydraulic hose and loose half 1", tipping angle approx. 48° Accessories 6 Parlok mudguards, full-width spray flaps fitted to underrun protection, aluminium spare wheel holder, foldable lateral underrun protection right-hand side, large 860-type toolbox, approx. 3 m aluminium ladder, 3 mid-position, approx. 150 mm raised swing bars, rolling tarp with central light strip and separate reinforcements at wear points, approx. 660 g/m² quality, with rolling tarpaulin system, perimeter rubber cord in rear end of tarp with two tension hooks to fix onto the rear swing bar, catwalk on bin with access on left, side tarp lock with tensioning straps, rear tarp closure with welded-in rubber cord for water resistance, robust foldable aluminium underrun guard with two towing eyes left and right including locking pins, 2 "Clear-Pass" spray flaps on the mudguard to EC standard, etc. Offer and images non-binding.