Kullanılmış Meusburger Flatbed/Branda satın al (58)

Durum: yeni, boş ağırlık: 10.100 kg, azami yük ağırlığı: 38.900 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.550 mm, lastik boyutu: 245/70 R 17,5, işletme ağırlığı: 10.100 kg, Donanım: ABS, Chassis: - Robust steel frame weldment with front frame cranking and flat loading surface with rear tapering approx. 500x100 mm - Neck of frame 200 mm with chamfered corners - Tapered end of gooseneck approx. 500 x 100 mm (anti-slip ribs on outer frame in the rear taper area) - 2 king pin positions with replaceable 2" king pin - Outer frame closed on the outside, perforated profile for lashing with tension straps (chains not possible) - Reinforced frame version / point load at centre of gravity - Provisions for extendable widening devices in the loading area - With excavator trough (without cover), depth approx. 220 mm, width approx. 600 mm, starting approx. after 2nd axle up to rear end - 1 pair of wheel recesses in front of axle with steel covers - (Covers with Körapur coating), depth approx. 400 mm, as well as 1 pair of wheel recesses between 1st and 2nd axle with steel covers - Rear underrun protection = extended end plate - Drop-down supports at the rear Ramps: - Two-part loading ramps, special version with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting device (only in combination with electro-hydraulic power pack) - Width approx. 800 mm - Timber surface - Incl. anti-slip ribs on the loading ramps Djdpjwviwkefx Ab Uowa - Secured in travel position with tension straps - Operation via control lever mounted at the rear, right in direction of travel - Laterally hydraulically adjustable Floor: - 35 mm larch floorboards with aluminium omega profiles Landing Gear: - Mechanical 24t landing legs with single-side operation and push compensation Axles, Steering and Tyres: - BPW air suspension axles, each with 10t axle load, air bag diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lifting and lowering mechanism with total lift approx. 200 mm - 2nd driving height via ball valve +50mm - 1st axle lift axle (wired via EBS), operation fully automatic with mechanical emergency actuation via button on the trailer - 3rd axle as friction steered trailing axle with electrical and mechanical lock - 12 steel disc wheels, 10-hole, with mid-offset centering - 12 tyres 245/70 R 17.5 143/141J, tubeless - Including tyre pressure monitoring Accessories: - Plug-in side and rear boards on the gooseneck, approx. 400 mm high - Spare wheel mounting - Lateral aluminium side impact protection - 4 wheel chocks - Elongated number plate holder in the end plate - 1 ECE panel insertable at the rear - 11 pairs of ZK modules 10t lateral: - 2x on the gooseneck - 9x on the loading surface - Steel mudguards with clear-pass - Slidable warning panels including 3 position lamps each, at the landing legs in front and behind the end plate, continuously extendable up to loading width of 4,500 mm - 4 removable holders for warning panels plug-in into stake pockets on the loading surface - 6 pairs of side stake pockets for 100x50 mm stakes - 2 rows of transverse stake pockets for 100x50 mm stakes on the gooseneck from outer frame to the main frame (1x in front of and 1x behind king pin positions) - 3 rows of transverse stake pockets for 100x50 mm stakes on the loading surface from outer frame to main frame (1x front area, 1x in front of 1st axle, 1x behind 3rd axle) - 2 pairs of steel plates in loading surface for container locks to accommodate 1 x 20ft container - Rubber flap fitted on underrun protection - Steel shot blasting, chassis hot-dip galvanized and primed - Chassis/wheel hubs/outer frame painted DB 7

Durum: yeni, boş ağırlık: 9.800 kg, azami yük ağırlığı: 39.200 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.550 mm, süspansiyon: hava, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 9.800 kg, Donanım: ABS, Chassis: - Robust welded steel frame construction with front frame cranking and level loading area with rear chamfer approx. 500x100 mm - Neck of frame 200 mm with beveled corners at the front - Slanted end goose neck approx. 500 x 100 mm (traction cleats on outer frame in the area of the rear chamfer) - 2 kingpin positions with replaceable 2” kingpin - Outer frame closed to the outside as a perforated outer frame - Load floor with extendable central frame, extendable by approx. 2,000 mm, lockable pneumatically in 500 mm increments - Frame in front of and after separation with 80x80 mm step - Reinforced frame design / point load in retracted state at center of gravity - Without extendable load area wideners, but prepared for subsequent installation (guide tubes welded into the frame) - With excavator trough (without cover), depth approx. 220 mm, width approx. 600 mm, starting about at the 2nd axle to the rear of the vehicle - 1 pair of wheel recesses between 1st and 2nd axle with steel covers (covers with Körapur coating), depth approx. 400 mm - Underrun protection = extended end plate - Drop supports at the rear Ramps: - 2 pcs. 2-part special-design drive-on ramps with mechanical extension - Length approx. 2,850 mm plus 1,850 mm, with hydraulic ramp lifting system (only in conjunction with electrohydraulic unit) - Width approx. 800 mm - Wooden deck - Incl. traction cleats on ramps - Secured in driving position with lashing straps - Operated via control lever mounted at rear right in FR - Lateral hydraulic displacement Floor: - 35 mm larch timber floor with aluminum omega profiles Dodpfx Aboxgm S Ds Uswa Landing Gears: - Mechanical support legs, 24 t, with single-sided operation and push-balanced Axles, Steering and Tyres: - BPW air suspension axles, 10 t axle load each, airbag diameter 360 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lift and lowering device with total stroke approx. 200 mm - 2nd driving position via ball valve +50mm - 1st axle lift axle (wired via EBS), automatic actuation with mechanical emergency actuation via button on the trailer - 3rd axle as friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, center-mount offset - 12 tyres 245/70 R 17.5 143/141J, tubeless - Incl. tire pressure monitoring Accessories: - Removable side walls and rear wall on the gooseneck, approx. 400 mm high - Spare wheel carrier - Lateral aluminum collision protection - 4 wheel chocks - 1 ECE board at the rear, plug-in - 11 pairs of ZK modules 10 t side-mounted: - 2x on the gooseneck - 2x on the loading area before the extension - 7x after the extension - Extendable warning signs including 3 position lamps each, at the front on the landing legs and at the rear in front of the end plate, infinitely extendable up to a loading width of 4,500 mm - 4 holders for warning panels, plug-in, in stake pockets on loading area - 6 pairs of stake pockets on the side for plug-in stakes 100x50 mm - 2 transverse rows of stake pockets for plug-in stakes 100x50 mm on the gooseneck from outer frame to main frame (1x before and 1x after kingpin positions) - 3 transverse rows of stake pockets for plug-in stakes 100x50 mm on loading area from outer frame to main frame (1x before extension, 1x after extension and 1x after 3rd axle) - 2 pairs of steel plates on the loading area for container locks to accommodate 1x 20ft container - Rubber skirt mounted on underrun protection

Durum: yeni, boş ağırlık: 8.950 kg, azami yük ağırlığı: 40.050 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.550 mm, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 8.950 kg, Donanım: ABS, Chassis: - Robust welded steel frame construction with a cranked front section and level loading area, with rear tapering approx. 500x100 mm - Neck height 200 mm with chamfered corners - Tapered end swan-neck approx. 500 x 100 mm (anti-slip ribs on outer frame in area of rear taper) - 2 king pin positions, replaceable 2" king pin - Closed outer frame with perforated outer profile for lashing with tension straps - Reinforced frame design / point load in center of gravity - Preparations for extendable loading area wideners - With excavator trough, approx. 220 mm deep, approx. 600 mm wide, extending approx. from after second axle to end of vehicle - 1 pair of wheel recesses in front of axle with steel covers - (Covers coated with Körapur), approx. 400 mm deep, and 1 pair of wheel recesses between 1st and 2nd axle with steel covers - Rear underride guard = extended end plate - Drop supports at rear Ramps: - 2 single-piece aluminum drive-on ramps with spring-assisted lifting function - Length x width approx. 2,500 mm x 600 mm - Lockable in transport position using tension straps - Manually sideways adjustable Floor: - 35 mm larch wood floor with aluminum omega profiles Landing Gears: - Mechanical 24t landing gears, one-side operation with load compensation Axles, Steering and Tires: - BPW air suspension axles, 10t axle load each, air bag diameter 360 mm - S-cam brake 300/200 mm, asbestos-free brake pads - Automatic slack adjuster - Lifting and lowering device, total stroke approx. 200 mm - 2nd ride height via ball valve +50 mm - 1st axle with lift function (wired via EBS), fully automatic confirmation with mechanical emergency actuation via push button on trailer - 3rd axle as friction-steered trailing axle with electrical and mechanical lock - 12 steel disc wheels, 10-hole, centered offset - 12 tires 245/70 R 17.5 143/141J, tubeless - Incl. tire pressure monitoring Brake System: - Dual-circuit brake system with EBS-E including RSS - EBS (WABCO 4S3M) - Spring-loaded parking brake - Air connections yellow / red Painting: - Steel shot blasting, spray galvanizing of frame and primer - Painting chassis/wheel hubs/outer frame in DB 7350 Nova Grey - Plastic parts black, unpainted - Rims: factory silver - Reflective tape side and rear in yellow Accessories: - Plug-in side and rear boards on the swan neck, approx. 400 mm high - Spare wheel holder - Aluminum docking protection - 4 wheel chocks - Sheet metal mudguards with Clear-Pass - Elongated license plate holder in end plate - 1 plug-in ECE panel at rear - 11 pairs of ZK modules 10t side: - 2x on the swan neck - 9x on the loading platform - Without rear tow rings - Extendable warning signs incl. 3 position lights each, front at landing gears and rear before end plate, infinitely extendable up to loading width 4,500 mm - 4 holders for warning signs, insertable into stake pockets on loading platform - 6 pairs of stake pockets on the side for insertable stakes 100x50 mm Dodpfjwu Agiox Ab Uowa - 2 rows of transverse stake pockets for insertable stakes 100x50 mm on swan neck from outer frame towards main frame (1x before and 1x after king pin positions) - 3 rows of transverse stake pockets for insertable stakes 100x50 mm on the loading platform from outer frame towards main frame (1x front, 1x before 1st axle, and 1x after 3rd axle) - 2 pairs of steel plates in the loading area for container locks to accommodate 1x 20ft container - Rubber apron mounted on underride guard

Durum: yeni, boş ağırlık: 11.000 kg, azami yük ağırlığı: 27.000 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.300 mm, yükleme alanı genişliği: 2.550 mm, lastik boyutu: 235/75 R17.5, renk: gri, işletme ağırlığı: 11.000 kg, Donanım: ABS, Chassis: - Welded steel frame construction with front and rear frame cranking and drop deck without rear bevel - Frame neck + fifth wheel plate 225 mm - Drop deck designed for a point load of 25 t over 5 m - Outer frame closed outward with welded-in lashing rings for securing loads - Interchangeable 2" kingpin - Rear mounting rail for aluminum ramps Axles and Tyres: - BPW low-bed trailer axles, each with a 10 t axle load, air bag diameter 360 mm - Air suspension with lifting and lowering function, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for two coupling heights +100 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - IVTM tire pressure monitoring system - 9 tires 235/75 R 17.5, tubeless Steering: - 1st and 2nd axle hydraulically forced steered via fifth wheel coupling Floor: - Multi-layer bonded flooring, 27 mm thick, flush with outer frame and longitudinal beams - Underside reinforced with GRP coating - 12 pairs of lashing rings welded into the outer frame (8 pairs RUD 8 t – 6 pairs in the drop deck as well as 1 pair each on the gooseneck and at the beginning of the rear unit – 2 pairs of 4 t lashing rings on both gooseneck and rear unit) - 6 pairs of mushroom-type lashing points in the outer frame in the drop deck - Storage compartment with lid in the front left and right of the drop deck floor Front Wall: - 25 mm aluminum hollow profiles raised to the lower edge of the roof with integrated tarpaulin tensioning system Sliding Tarpaulins: - Sliding curtain both sides with welded-in vertical and horizontal straps (approx. 600 mm spacing) and stainless-steel tension locks - Adjustable curtain straps (over-center) for loading width up to 4,000 mm including curtain extension with press studs and Velcro fastener - Curtain extension in driving direction: 300 mm, in height: 750 mm - Incl. eyelets for loose curtain extension part - 1 pair of vertical curtain pockets approx. 1,000 mm length, positioned in the drop deck at the front cranking - With belt pockets Rear Wall: - Steel rear portal frame with side tarpaulin hook-in device - Aluminum double-wing door, 25 mm thick - Both door wings fully foldable with door retainer - One aluminum double-joint hinge and two recessed grip recesses per door wing Dwjdpfoiu Eu Njx Ab Uoa Front Corner Posts: - At roof height, bolted at the front end Central Posts: - 3 pairs of continuously adjustable folding stanchions - Stanchions can be moved along the entire length via trolleys - Central stanchions in the drop deck can also be fixed at the rear platform Roof: - EDSCHA sliding roof (galvanized) with crossbeams that can be shifted in both directions (pushed together to the front in the cargo area) - Rear portal cross member can be swiveled away - PVC tarpaulin roof without customs seal - Hand-operated hydraulic lifting roof on both sides, lift 450 mm - Raised roof movable to the front (9x50) and rear (9x50) positions - Including rear curtain extension and curtain skirt - Roof can be cranked out at the very front on the bulkhead by 900 mm each Accessories: - Extendable warning boards (removable front and rear with socket) incl. position lights up to 4,000 mm loading width - Storage for 4 warning boards on the front wall, top right and left inside - 1 aluminum ladder with bracket, 2,500 mm long, mounted on the front wall - 2 rows of self-locking aluminum slats - Sheet metal fenders with mud flaps - 1 night parking sign and 1 ADR panel on the rear wall - Central lub

Durum: yeni, boş ağırlık: 8.490 kg, azami yük ağırlığı: 40.510 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.550 mm, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 8.490 kg, Donanım: ABS, Chassis: - Robust welded steel frame construction with front frame drop and level loading area, rear taper approx. 500x100 mm - Neck height 200 mm with beveled corners - Tapered end of gooseneck approx. 500 x 100 mm (traction ribs on outer frame in the area of the rear taper) - 2 king pin positions with interchangeable 2” king pin - Outer frame closed on the outside as a perforated outer frame for lashing with tie-down straps - Reinforced frame design / point load at the center of gravity - Prepared for extendable load width extensions Dodpfxowu A Slo Ab Uswa - With excavator recess (open type), depth approx. 220 mm, width approx. 600 mm, beginning just after 2nd axle to end of vehicle - 1 pair of wheel recesses in front of axle with steel covers - (Covers with Körapur coating), depth approx. 400 mm, as well as 1 pair of wheel recesses between 1st and 2nd axle with steel covers - Rear underrun protection = extended end plate - Drop-leg stabilizers at rear Floor: - 35 mm larch wood floor with aluminum omega profiles Axles, Steering, and Tires: - BPW air suspension axles, each with 10 t axle load, air bellow diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lift and lowering mechanism, total travel approx. 200 mm - 2nd ride height setting via ball valve +50 mm - 1st axle lift axle (wired via EBS), confirmation fully automatic with mechanical emergency operation via pushbutton on trailer - 3rd axle is a friction-steered trailing axle with electric and mechanical lock - 12 steel disc wheels, 10-hole, with centered offset - 12 tires 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring Brake System: - Dual-line brake system with EBS-E including RSS - EBS (WABCO 4S3M) - Spring-loaded parking brake - Air connections yellow / red Paintwork: - Steel shot blasting, chassis spray galvanizing and priming - Painting of chassis/hub/outer frame in DB 7350 Novagrau Accessories: - Removable drop sides and tailboard on gooseneck, approx. 400 mm high - Spare wheel holder - Side aluminum underrun protection - 4 wheel chocks - Metal mudguards with Clear-Pass - Long number plate holder integrated in end plate - 1 removable ECE plate at rear - 11 pairs of ZK-modules 10t side-mounted: - 2x on the gooseneck - 9x on the loading area - Without rear towing eyes - Extendable warning signs incl. 3 position lamps each, at the front at landing gear and rear before end plate, infinitely extendable to a loading width of 4,500 mm - 4 holders for warning signs, insertable in stake pockets on loading area - 6 pairs of side stake pockets for insertable stanchions 100x50 mm - 2 cross rows of stake pockets for insertable stanchions 100x50 mm on gooseneck, from outer frame to main frame (1x before and 1x after king pin positions) - 3 cross rows of stake pockets for insertable stanchions 100x50 mm on loading area, from outer frame to main frame (1x at the front area, 1x before 1st axle, 1x after 3rd axle) - 2 pairs of steel plates in loading area for container locks to accommodate one 20ft container - Rubber apron mounted on underrun protection - Preparation (wiring for NATO cable and hole pattern for retrofit installation of NATO socket at front of end plate and bracket on vehicle) for subsequent installation of an electrohydraulic unit on the right rear side for possible ramp operation - Mechanical landing legs 24t, single-sided operation with load compensation Optionally, the trailer is available with aluminum approach ramp

Durum: ikinci el, makine/araç numarası: W09TS300870M49625, boş ağırlık: 12.400 kg, azami yük ağırlığı: 32.600 kg, toplam ağırlık: 450.000 kg, dingil konfigürasyonu: 3 dingil, toplam uzunluk: 14.340 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 3.780 mm, lastik boyutu: 235/75R17.5, renk: mavi, Üretim yılı: 2008, The Meusburger MTS 3 low-loader is the perfect solution for anyone seeking a reliable, robust, and versatile semi-trailer. Its high-quality workmanship and sturdy construction ensure long service life and maximum safety during every operation. Thanks to its generously sized deck, the MTS 3 offers ample space for a wide variety of loads, whether in construction or heavy haulage applications. The superior build quality and durable design make it a sound investment for any business, guaranteeing longevity and reliability. If you are interested, we are happy to provide further information or a consultation upon request. Performance Features / Basic Data: - Number of axles: 3 - Length: 14.34 m Dedeygxb Sjpfx Ab Uswa - Width: 2,550 mm - Height: 3,780 mm - Tare weight: 12,400 kg - Fifth wheel load: 18,000 kg - Gross permissible weight: 45,000 kg - Maximum axle load: 10,000 kg - Tyres: 235/75R17.5 Equipment: - Two-part hydraulic rear ramp - Axle spacing 1/2: 1.41 m - Axle spacing 2/3: 1.31 m - First axle: liftable - Axles 2 and 3: hydraulically forced steering - NATO socket

Durum: ikinci el, boş ağırlık: 8.900 kg, azami yük ağırlığı: 40.100 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2025, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.550 mm, süspansiyon: hava, lastik boyutu: 245/70 R 17,5, renk: gri, Üretim yılı: 2025, Donanım: ABS, With every used semi-trailer, you receive a current and complete inspection and functional report. Chassis: - Robust steel frame welded construction with front frame neck and flat loading area with rear taper approx. 500x100 mm - Neck height 200 mm with chamfered front corners - Inclined goose neck end approx. 500 x 100 mm (climbing ribs along the outer frame in the rear taper area) - Two kingpin positions with exchangeable 2” kingpin - Outer frame closed outward, constructed as a slotted outer frame - Loading platform with extendable central beam, can be extended by approx. 2,000 mm, pneumatically lockable at 500 mm intervals - Frame before and after division with 80x80 mm step Dwedpfx Asywv Ixeb Uja - Reinforced frame design / point load in retracted position at the center of gravity - No extendable load bed wideners, but prepared for retrofitting (= guide tubes welded into frame) - With excavator trough (without cover), approx. 220 mm deep, 600 mm wide, starting after the 2nd axle to the end of the vehicle - 1 pair of wheel recesses between 1st and 2nd axle with steel covers (covers with Körapur coating), approx. 400 mm deep - Underrun protection = extended end plate - Drop leg supports at rear Floor: - 35 mm larch timber flooring with aluminum omega profiles Axles, steering, and tires: - BPW air suspension axles, 10 to axle load each, air spring diameter 360 mm - S-cam brakes 300/200 mm, asbestos-free brake linings - Automatic slack adjuster - Lifting and lowering system with total stroke approx. 200 mm - Second driving position via ball valve +50 mm - First axle as lift axle (wired via EBS), fully automatic activation with manual emergency actuation via push button on the trailer - Third axle as friction-steered trailing axle with electric and mechanical locking - 12 steel disc wheels, 10-bolt, hub-centered - 12 tires, 245/70 R 17.5 143/141J, tubeless - Including tire pressure monitoring system Accessories: - Plug-in side boards and rear board on the gooseneck, approx. 400 mm high - Spare wheel holder - Side aluminum impact protection - 4 wheel chocks with holder - Elongated number plate holder in end plate - 1 ECE insertable reflector board at rear - 11 pairs of 10t side ZK lashing modules: - 2x on the gooseneck - 2x on the platform before extension - 7x after extension - No rear towing eyes - Extendable warning boards including 3 position lamps each at the front at the landing gear and rear before the end plate, steplessly extendable to loading width of 4,500 mm - 4 insertable sockets for warning boards in stakes pockets on the platform - 6 pairs of side stake pockets for 100x50 mm stake inserts - 2 rows of cross stake pockets for 100x50 mm stakes on the gooseneck from outer frame inward to main frame (1x before and 1x after kingpin positions) - 3 rows of cross stake pockets for 100x50 mm stakes on the load platform from outer frame inward to main frame (1x before extension, 1x after extension, and 1x after 3rd axle) - 2 pairs of steel plates in the platform for container locks to accommodate one 20ft container - Rubber apron mounted on underrun protection - Preparation (= cable routing for NATO cable and drilling pattern for later installation of NATO socket at the front end plate, as well as holder on the vehicle) for retrofitting electrohydraulic power unit on the right rear, for possible control of loading ramps Optional: The trailer is available with aluminum approach ramps.

Durum: ikinci el, dingil konfigürasyonu: 3 dingil, ilk tescil: 12/2012, toplam uzunluk: 13.860 mm, toplam genişlik: 2.550 mm, süspansiyon: hava, lastik boyutu: 235/75R17.5, dingil mesafesi: 11.250 mm, renk: siyah, Üretim yılı: 2012, 400 cm extendable. 3 x steering axles. Remote steering. Loading platform: 565 cm + 400 cm. Loading height: 45 cm. = Further Information = Axle configuration Tyre size: 235/75R17.5 Brakes: drum brakes Suspension: air suspension Rear axle 1: twin tyres; steered; tyre tread left inner: 30%; tyre tread left outer: 50%; tyre tread right inner: 30%; tyre tread right outer: 50% Rear axle 2: twin tyres; steered; tyre tread left inner: 40%; tyre tread left outer: 40%; tyre tread right inner: 40%; tyre tread right outer: 40% Rear axle 3: twin tyres; tyre tread left inner: 30%; tyre tread left outer: 40%; tyre tread right inner: 30%; tyre tread right outer: 40% Dwsdpfjwypatjx Ab Uja Weights Unladen weight: 13,320 kg Payload: 34,680 kg Gross vehicle weight: 48,000 kg Identification Model number: MPG 3 / EXTENDABLE / LOW BED / 3 = Company information = ALL PRICES ARE NET EXPORT PRICES. Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT), We speak Russian. We strive to provide accurate information, but no rights can be derived from the provided descriptions.