Kullanılmış Hangler Flatbed/Branda satın al (8)

Durumu: yeni, makine/araç numarası: cd0062ee491e6794168ccb01a, boş ağırlık: 8 kg, azami yük ağırlığı: 26 kg, toplam ağırlık: 35 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 435/50 r 19,5, Further Information Chassis of Semi-Trailer Proven HANGLER welded construction made of high-quality steel with tapering UP-welded longitudinal beams towards the front. Neck height of the frame: 120 mm, with double central web. Z-profile cross members punched through the longitudinal beams with floor boards (greater spacing) and welded special side frame. Two kingpins in accordance with DIN 74080, replaceable, with sloped wear plate at the front, made of high-grade sheet steel. EU front swing radius: 2,040 mm. Wear plate runs seamlessly from the fifth wheel plate to the front panel *internally welded*. 18 pairs of lashing rings embedded in the outer frame, each rated at 2.5 t 8 pairs of lashing rings embedded in the outer frame, each rated at 5 t 24 t, two-speed landing gear, single-side operation, with straight lower section, without load equalization 2 wheel chocks with holder Aluminium side underrun protection Plastic fenders with splash guards Rear underrun protection Rear impact guard Spare wheel carrier for one spare wheel, with wheel fixing kit 3 plastic toolboxes with drawer and shelf, dimensions: W=650 / H=520 / D=670 mm, lockable with a padlock (padlock not included) Aluminium ladder 3,300 mm, loose Pair of stake pockets recessed Removable stakes Storage compartment for insert slats on one side, front left, below the loading area Open storage compartment for sideboards underneath the loading area, as far as technically feasible Coil trough / angular loading device Coil trough, 8,000 mm long, with cover and rubber lining. Cover 35 mm. Slant loading beams with bushing and supports to suit FR 80/80/4, fully supplied with 80/80 plug-in stakes including bottom reinforcement Hydraulic slant loading device with 4 cross beams: Hydraulic supply via tractor unit using a 2-line pump system (feed and return), with dual Faster coupling installed on the front bulkhead (hoses connected from below with Faster coupling). Slant loading beams (FR 180x100x8 mm) with integrated extension, height-lockable. Multistage hydraulic cylinders, each beam with gimbal mounting. Including supports – adjustable – with bolt lock under loading platform. 5-way control block for operating the slant loading device and for the sliding roof folding mechanism. 1 set of vessel head mountings with height-adjustable support pins for different vessel head diameters, including a rack. 1 proximity guard for slant plate – for forward safety! Gijdpfx Aei Riw Hoa Eol Axles + Suspension SAF disc brake axles Axle spacing (offset) mm Air suspension Braking System 2-line compressed air brake system Aluminium air tanks Spring-loaded parking brake 2 foolproof coupling heads at the front, without connecting lines EBS by Wabco, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles guaranteeing the effectiveness of the ABS! With lifting & lowering valve + auto-reset function Vehicle stability system Wheels and Tyres 435/50 R 19.5, as per manufacturer's choice Steel rims painted factory silver, as per manufacturer's choice Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane markers at the rear 2 x 7-pin foolproof sockets at the front, without connecting cable 1 additional LED work light at the rear, switchable via reversing light 2 pairs of warning panels, double LED-illuminated and extendable to 3,000 mm, removable with plug 1 rotating beacon with holder

Durumu: kullanılmış, makine/araç numarası: 8c9a877b63be8509f58298a74, boş ağırlık: 7.170 kg, azami yük ağırlığı: 25.830 kg, toplam ağırlık: 33.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2007, lastik boyutu: 455/40 r22,5, Further information 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! Gsdpfji Ri Aksx Aa Esil Air suspension with lifting and lowering function, BPW disc brake axles, 2-speed landing gears with compensating mechanism, 1 plastic toolbox, sliding roof, side curtain, double-wing rear portal doors, spare wheel holder without wheel, hazardous goods sign, A-sign, document tube, customs cord. 4 rows of aluminum insert slats, coil well approx. 7,000 mm long, 2 rear impact buffers, warning plates according to ECE-070, tires approx. 30 - 40% 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE!

Durumu: kullanılmış, azami yük ağırlığı: 13.830 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 02/2012, Üretim yılı: 2012, Donanım: ABS, Trailer HANGLER 2 PEL 18, 2-axle flatbed with tarpaulin and drop sides, equipped with stanchion holders Unladen weight: 4,170 kg Payload: 13,830 kg Godpfex Sbrxjx Aa Ejil Condition: Excellent Tyres: 70–90%

Durumu: kullanılmış, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2008, Üretim yılı: 2008, Donanım: ABS, Hangler Refrigerated Trailer ThermoKing SLX 200 Meat Rail System All at a glance · First registration: 18.07.2008 · Year of manufacture: 2008 · Diesel engine hours: 15,820 hours · Color: White · Unladen weight: 6,790 kg · Internal dimensions: approx. 7,350 x 2,480 x 2,400 mm (LxWxH) · Tyres: 385/65 R 22.5 · Note: Immediately available Special features ThermoKing SLX 200 refrigeration unit (diesel/electric), NEW battery, Chereau body year 10.2, meat rail system (5 tracks), wear plate, spare wheel holder with spare wheel, 2 LED reversing lights, toolbox, longitudinally adjustable drawbar, inspection and system log book. Standard features 2-axle, ABS, EBS, lifting and lowering valve, wheel chock, disc brakes (430mm), dock bumpers, underrun protection, rear access ladder. Errors, clerical mistakes and prior sale reserved. The seller reserves the right to withdraw from the sale. _____ Internal reference for inquiries: TR25318 _____ Giedpjx Aylcsfx Aa Eol STARENT Truck & Trailer GmbH Bruck 49, A - 4722 Peuerbach Sales contacts: Mr. Ing. Wimmer Christoph (German, English, Czech, Polish, Italian) p: also WhatsApp t: @: Mr. Mehmet Terzi (German, Turkish, English, Russian, Ukrainian, Bosnian, Serbian) p: / also WhatsApp t: -104 @: Mr. Elias Höfler (German, English, Bulgarian, Bosnian, Serbian) p: / also WhatsApp t: -123 @: We speak 13 languages, probably yours too. Contact us! Homepage: Facebook: Instagram: Starent Truck & Trailer GmbH buys your commercial vehicles such as tractor units, trailers, trucks, and vans. Michael Doblhofer (German, English) p: also WhatsApp t: -102 @: Michael Leirich (German, English) p: WhatsApp t: -125 @:

Durumu: kullanılmış, azami yük ağırlığı: 30.480 kg, toplam ağırlık: 41.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2023, bir sonraki muayene (TÜV): 03/2026, yükleme alanı uzunluğu: 17.270 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 850 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 850 mm, Üretim yılı: 2023, Donanım: ABS, HANGLER 3-Axle Semi Low Loader Extendable Type SDS-H 470 First registration 03/2023, in like-new condition Unladen weight only 10,520 kg Loading height (unladen) approx. 850 mm Coupling height 1,050 to 1,100 mm Gooseneck length 3,650 mm Low-bed length 9,770 mm, extendable by 7,500 mm = total low-bed length 17,270 mm; movable intermediate support on the telescopic section Extra-wide package up to 3,000 mm width, extendable frame widenings including timber decking Rear frame slope 8° Continuous U-profile mounting rail for approach ramps Front support legs telescopic Rear supports telescopic 4 pairs of container locks recessed in the floor for 1 x 40 ft or 2 x 20 ft container 9 pairs of stake pockets recessed in the outer frame 2 stake pocket strips, continuous across the width Plastic toolbox Godpfx Aaou Dftvo Eeil Ramp storage box 11 pairs of folding lashing rings, each rated for 10,000 daN, freely swiveling in the side profile (also suitable for securing oversize loads) 11 pairs of lashing holes in the outer frame on the gooseneck (for attaching ratchet straps) Tyres: 13-fold 235/75 R 17.5 SAF axles with drum brakes Air suspension with raise/lower function Axle spacing offset: 1,360/1,410 mm 3rd axle is self-steering WABCO Trailer EBS with RSS driving stability system Chassis frame front: spray-galvanized + finished in RAL 3002 Chassis frame rear: hot-dip galvanized + outer frame visible area finished in RAL 3002 RENTING is the new BUYING—Available immediately for full-service rental.

Durumu: kullanılmış, boş ağırlık: 8.450 kg, azami yük ağırlığı: 26.550 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 04/2007, süspansiyon: hava, lastik boyutu: 385/65 R22,5, Donanım: ABS, Hangler platform dorse 3 dingilli | Yönlendirilebilir dingil | BPW dingiller disk frenli | Azami yüklü ağırlık 35.000 kg | Stepne tutuculu + stepne | Takım sandığı | 3 metre uzatılabilir | Lastikler: 385/65 R22,5 | Hata, yazım hatası ve ön satış hakkı saklıdır. Gisdpfswz Ekksx Aa Esl

Durumu: yeni, makine/araç numarası: c78894767223a51dd199030f3, boş ağırlık: 4.600 kg, Further Information Frame Steel welded construction made of high-tensile fine-grained steel, hot-dip galvanized, flat platform without raised edges. The loading area is sloped downward by approx. 8° behind the rear axle. Longitudinal beams made from steel profiles. Steel frame, hot-dip galvanized, with stainless steel (NIRO) sheet at the bend for cable guiding, flush with the floor. Suitable for trucks with wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4,105 mm and 3rd to 4th axle 1,350 mm. Tow Coupling Tow coupling with 24.8 mm tow ball (height from ground to top approx. 480 mm), towing capacity 2,800 kg. Includes installation and electrics with 7-pin socket. Accessories/Modifications 2 holders for wheel chocks, folding aluminum side underrun protection – transferred from the truck! Steel underrun protection, quarter shell mudguards with mudflaps – also taken from the truck! Toolbox Plastic tool case with drawer and shelf, width 650 mm, height 520 mm, depth 670 mm, lockable with padlock (padlock not included). 1 holder for 3 petrol canisters. 1 stainless steel toolbox, width 600 mm, height 400 mm, depth 500 mm, with polished door, lockable; contains control valve and electrohydraulic pump unit. Control box features all-round door seal and rear sealing grommets (splash water protected according to technical possibilities). Electrics Adaptation of existing rear lights, 2 additional LED work lights integrated into the front wall, switched via parking light with switch on the outside left of the front wall. 1 rear LED work light with integrated reversing camera, including color LCD monitor, screen with suction mount and 24 V power supply, voltage converter 24/12V, 1 seven-pin 12V socket = adapter socket. Floor Mega Grip made of toothed galvanized steel grating, 50/4 steel grating, mesh width 50 mm. Upper surface with non-slip serration, fully installed over main frame platform. Lashing Rings 12 pairs of lashing rings, freely swiveling on the outer frame, each rated for 10 tons. One at the very front, the last at the very rear. 1 lashing ring in the center at the rear for winch cable attachment. 12 lashing points embedded in the center of the floor, each rated for 5 tons (excluding rear slope). Front Wall Front wall made of sheet steel, height 1,500 mm. Fixed, with corner posts matching the front wall height. 2 x 12 mounting brackets for lashing chains, mounted left and right on the front wall. Winch Electric winch, 24 Volt, pulling force approx. 6,350 kg, mounted centrally at front wall (recessed with loading bridge), operated via radio remote control, cable length min. 35 m x 9.5 mm, with roller fairlead, cable pressure plate, incl. overload protection, free-spooling clutch, hand controller with approx. 5 m control lead, winch certification, engineering inspection report, inspection book, operating manual. Gjdpsk Unitefx Aa Ejil Loading Ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg/pair (also for ramp loading), electrohydraulically tiltable and laterally shiftable – incl. electrohydraulic pump unit. Approach angle approx. 8° with lowered rear axle. Ramp surface made of hot-dip galvanized steel grating (like the loading bridge floor), with non-slip serration. Ramps can be compressed to approx. 170 mm, ramps extendable hydraulically. Ramps preconfigured for operation on loading docks at full load capacity. Ramp locking with 2 lashing straps. Ramp tips set back (nose min. 150 mm) suitable for docking at loadi

Durumu: yeni, makine/araç numarası: 087c7b6bc0c6118a84279fb46, boş ağırlık: 4.100 kg, Further Information Gedpfei Riytex Aa Esil Frame Steel welded construction made of fine-grained steel, hot-dip galvanized, flat platform without raised edges, load area beveled downward by approx. 8° behind the rear axle. Longitudinal beams made from steel profiles. Steel frame hot-dip galvanized, with stainless steel plate at the bending point as rope guide—flush with the floor. For trucks with wheelbase: 2nd axle 5,100 mm / 2nd to 3rd axle 1,350 mm. Towing Coupling Towing coupling ball head D24.8: (height from ground to top approx. 480 mm), towing capacity 2,800 kg, incl. installation and electrical wiring with 7-pin socket. Accessories/Modifications 2 holders for wheel chocks, foldable aluminium side underrun protection – transferred from the truck! Steel underrun protection, quarter-shell mudguards with mudflaps – transferred from the truck! Storage Boxes Plastic toolbox with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included). 1 holder for 3 fuel canisters. 1 stainless steel storage box, w=600 / h=400 / d=500 mm, with polished door, lockable, contains control valve and electrohydraulic pump unit. Control box with circumferential door seal and sealing sleeves on rear (splash proof according to technical feasibility). Electrics Adjustment of existing taillights, 2 additional LED work lights recessed into front wall, switched via parking light with switch on outer front wall left side, 1 LED work light at rear, with integrated reversing camera incl. color flat screen monitor, monitor with suction cup mount and 24V power supply, voltage converter 24/12V, 1 7-pin 12V socket = plug adapter. Floor Mega Grip galvanized serrated grating, steel grating 50/4 mm incl., mesh size 50 mm. Top side with anti-slip serration, continuous over the entire main frame platform. Lashing Rings 12 pairs of pivot-mounted lashing rings on the outer frame—each rated 10 tons. One at the very front and one at the very rear. One lashing ring at the very rear in the center for winch cable attachment. 12 lashing points recessed centrally in the floor, each rated 5 tons (not included in rear bevel). Headboard Headboard made from steel sheet, height 1,500 mm. Fixed, with corner posts the height of the front wall. Each with 2 x 12 suspension brackets for lashing chains on left and right sides of the headboard. Winch Electric winch, 24 volt, pull rating approx. 6,350 kg, mounted centrally at headboard (recessed into loading platform), operated by radio remote control, rope length min. 35 m x 9.5 mm, with roller fairlead, with rope pressure plate, incl. overload protection, freewheeling clutch, hand control with approx. 5 m control cable, winch certification, civil engineer test report, inspection book, operating manual. Ramps Length 3,500 mm – 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg/pair (also during ramp loading), electrohydraulically foldable and laterally adjustable – incl. electrohydraulic pump unit. Ramp angle approx. 8° with lowered rear axle. Ramp base made of hot-dip galvanized steel grating (same as loading platform), with anti-slip serration. Ramps can be contracted to approx. 170 mm, hydraulic ramp extension. Ramp prepared for operation at loading docks with full load capacity. Ramp locking with 2 tension straps. Ramp tip offset (nose min. 150 mm) suitable for resting on loading ramps. Ramp operation labeling. Descent brake valve for lowering ramp. Support Height-adjustable support legs at rear, foldable a