Alçak şasi römork

MÜLLER-MITTELTAL T4 Radmulden / luftgefedert

* T4 RM 40.0:
* Wabco EBS-E (electronic braking system)
* Emergency release device for spring-loaded brake cylinders
* Tire pressure monitoring system with display in the truck via EBS signal -no installation required on the truck-
* Drum brakes
* 4 x 11 t Gigant axles
* Air suspension with manual lowering at the rear
* Warning panel packages at front & rear
* SmartBord information tool mounted with pressure sensors for axle load display per axle group
* Reflective contour tape on the sides and rear
* Removable LED beacon at the rear
* 15-pin power connector
* LED tail lights
* Straight drawbar with 50 mm towing eye and continuously adjustable height
* Closed plastic single mudguards at the front
* Straight steel rear mudguards each with spray protection (anti-spray devices)
* Side underrun protection
* Front section ahead of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lid opens to the rear)
* Chassis made from high-strength fine-grained steel
* Floor above the turntable platform: 50 mm coniferous wood; on the low-bed platform: 60 mm coniferous wood
* Outer planks of the drive-on ramps made from 50 mm hardwood
* Load securing package consisting of: 2 lashing eyes, 6.4 t each, at the front left and right on the main frame of the turntable platform; 1 pair of 13.4 t lashing rings at the side, front and rear, on the outer frame; moreover, 1 pair of 10 t lashing rings per side, pivotable and lowerable, loadable in all directions and recessed in the outer frame; 5 t lashing rings screwed to the outer frame of the wheel recesses (2 each at the front and 1 at the rear wheel recess); 2 pairs of 6.4 t lashing rings at the side in the excavator arm storage area
* 11 pairs of folding outriggers for 3 m overall width (not at the tapering rear end)
* Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for widening planks, made of sheet steel, mounted transverse to the loading area in front of the 1st rear axle
* Excavator arm trough above the rear axle to the end of the approach slope, approx. 2,300 x 740 x 190 mm
* Each side with 2 wheel recesses, approx. 640 mm wide; front 340 mm deep, rear 220 mm deep, with sliding covers (storage for covers at the front on the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm
* Mechanical drop-down supports at the rear
* Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm
* Hydraulic lateral ramp shift
* Loading area above the turntable: approx. 2,990 x 2,520 mm
* Rear loading area: approx. 6,780 x 2,520 mm, loading height (laden) approx. 890 mm +/- 20 mm (including 860 mm approach slope)
* Chassis, turntable, folding outriggers, rear drop-down supports, and access ramps all hot-dip galvanized
* Axles, air tanks, and drawbar painted in black
* Tires: 235/75R17.5
* Vehicle is hot-dip galvanized
* New vehicle with manufacturer warranty
* Subject to errors and prior sale
* Available from KW 14/2026
Fodpfx Aaoxmpykscepn
* Sample images

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.