Alçak şasi römork

MÜLLER-MITTELTAL 3-Achs Plateau, luftgefedert, hydr. Rampen

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * PT 30 Profile: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lifting and lowering function, including return-to-ride (RtR) valve * Smart-Board installed on the trailer as an infotool (for displaying axle loads – separate display for front and rear) * Tire pressure monitoring system with display option in the truck via EBS signal, no truck-side installation required * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign sets at front and rear * Front axle with plastic quarter mudguards and spray protection * Rear axle with straight, galvanized steel apron and spray protection * Reflective contour tape on the side and rear * 15-pin electrical connector Cedpfx Agjtplwiewspw * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar 1,200 mm long with 40 mm draw eye and height adjustment via draw spring & turnbuckle * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted on the right side * Compartment in the turntable for accessories with folding lid, 2 fixed container locks (directly after the turntable platform) * ROBOT-welded anti-slip covering on the steel plate of the turntable platform (with protruding weld seams) * Load securing package consisting of: 2 lashing eyes (13.4 t) at the front left & right at the bulkhead support, one pair each of UVV lashing rings (13.4 t) front & rear, 3 pairs of swing- and lowerable UVV lashing rings (10 t each) per side, loadable in all directions and integrated into the outer frame, plus 3 stake pockets per side, each with additional 2 t lashing possibility * 6 pairs of mechanical folding outriggers for up to 3 meters total width (not in the rear taper) * Widening planks stored in the center of the cargo area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanical lateral adjustment * 4-section control block prepared for future retrofit of hydraulic ramp shift * Excavator stick support over rear axle, extending to rear cross member (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator stick support, mounted on the side in the longitudinal frame * 2 galvanized steps at the turntable, left & right * Profifix lashing rail along the center longitudinal axis, in flat area, with lashing points up to LC 3000 daN * Chassis, turntable, folding outriggers, drop supports, and loading ramps hot-dip galvanized * Axles, slewing ring, air reservoirs, and drawbar painted in black * Loading edge height laden approx. 910 mm +/- 20 mm (air suspension) * New vehicle with manufacturer’s warranty * Subject to error and prior sale * Available approx. from calendar week 22/2026 * Sample images

Durumu: yeni, Fonksiyonellik: tamamen fonksiyonel, boş ağırlık: 7.500 kg, azami yük ağırlığı: 36.500 kg, toplam ağırlık: 44.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.190 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 900 mm, süspansiyon: çelik-hava, lastik boyutu: 235×75 R17,5, dingil mesafesi: 1.310 mm, Üretim yılı: 2024, Donanım: ABS, merkez döner tabla, CETRATEK 4-Axle Low Loader TL89.4 (EU-COC) Short Description Robust low loader for heavy machinery transport. Frame constructed from high-strength ST-52/S355 steel, with optional fine-grained steel S700. Each ramp supports up to 20 t load, can be folded mechanically or hydraulically without loss of capacity. Optionally available as a low-bed version, with loading height in the wheel recess area adjustable from approx. 900 mm down to approx. 500 mm. Dimensions / Construction Overall length: 11,914 mm, overall height: 3,775 mm (over ramps) Platform: Gooseneck 2,440 mm + loading area 6,750 mm Width: 2,540 mm (manually extendable by 250 mm on each side) Coupling to 1st axle: 2,767 mm, to 2nd/3rd axle: 6,136 mm Axle spacing: front 1,310 mm, rear 1,360 mm Cpsdpfxeu Rbzvs Agwsw Platform height: 900 mm (low-bed approx. 500 mm), track width 1,850 mm Rear ramps: 3,000 × 750 mm, laterally adjustable, 20 t per ramp Drawbar eye height: 400–900 mm; turntable Ø 110 mm (CYR) Floor: steel + 45 mm hardwood (hornbeam), coated for protection Weights / Capacity a) GVW 44,000 kg → Payload approx. 36,500 kg* b) On-road 24,000 kg → Payload approx. 16,500 kg * Version a) requires a special permit according to §70 StVZO; appraisal/DEKRA inspection available at extra cost. Drawbar eye Ø 50 mm (optional Ø 40 mm), unladen weight approx. 7,500 kg Rear supports: manual (hydraulic option available) Steel Structure / Chassis Welding qualification TS EN ISO 9606-1, processes TS EN ISO 4063, shielding gases TS EN ISO 14175 4 × 11-t axles (TRAX), tyres 235/75 R17.5 (16 pcs., PETLAS or equivalent; Continental/Michelin available at extra cost), rims 6.75×17.5, air suspension, approved up to 100 km/h Brakes / Electrics WABCO EBS 4S/2M, linings 330×200, air tanks 2×80 L + 1×60 L Brake cylinders: 4× type 24 + 4× type 24/30, levers 165 mm Voltage: 24 V (voltage converter required with 12 V towing vehicle) Side reflectors: 4× LED per side + 2× white front reflectors, rear lights 2× LED, 2× triangular reflectors Connections: 7-pin EBS ISO 7638, 7-pin ISO 1185/3731, 15-pin ISO 12098 Tractor operation notice: 12→24 V converter as well as ABS/EBS connection (ISO 7638) and power supply (e.g., ISO 1185/12098) required for on-board hydraulics. Hydraulics (Ramps) 2 cylinders, including changeover valve to use tractor unit’s on-board hydraulic system Accessories (extract) 2 toolboxes, 2 wheel chocks (metal), fire extinguisher box Reflectors (side white/yellow; extensible yellow/red), rectangular rear reflectors Lashing eyes: 7 per side + 6 on the platform (10 t each) Mud flaps (front/rear), hose/cable holders on the drawbar Paintwork Sandblasted, 3× epoxy primer, 3× acrylic (≈ 230 µm), 1× acrylic clear coat Warranty 2 years on frame structure and axles (excluding accidents/operator error) 2 years on electrical & braking system (excluding wear parts such as brake pads, accidents/operator error) 1 year on paintwork (excluding accidents/operator error) Technical specifications and prices subject to change without notice. Images for illustration purposes only and may include optional features.

Durumu: kullanılmış, Üretim yılı: 2012, çalışma saatleri: 2.174 h, Contact Geert Geuens for further information. Cedpfx Aox Th Hfogwepw

Durumu: kullanılmış, azami yük ağırlığı: 15.860 kg, toplam ağırlık: 21.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 09/2024, bir sonraki muayene (TÜV): 06/2026, yükleme alanı uzunluğu: 4.995 mm, yükleme alanı genişliği: 2.380 mm, yükleme alanı yüksekliği: 1.000 mm, * KA-TA-R 21.0: * Wabco EBS (electronic braking system with RSS) * Emergency release device for spring-loaded cylinders * Drum brakes * Gigant axles * Air suspension with level control during tipping operation * Start-up assistance for maneuvering purposes on the 1st axle (actuated via EBS) * 1st axle as a lift axle (fully automatic) * Jost landing gear at the front * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * 7-pin 12V power plug * Multi-chamber rear lights with galvanized protective housing * 2 LED reversing lights * 1 LED work light on each side * Drawbar with K80 ball-type coupling (adjustable mm, coupling height approx. 440–550 mm when loaded) with elevated gallows for connection lines * Bolted and galvanized steel underrun protection * Plastic quarter mudguards in front of the first and behind the last axle * Shovel and broom holder on the front crossmember * Chassis made of fine-grain steel * Steel 3-way tipper body (front wall fixed, uninterrupted sidewalls – without center reinforcement –, right sidewall swingable via central locking and foldable with drop-side spring-assist, left sidewall foldable with drop-side hydraulics, tailgate swingable via automatic hook lock, 5 mm steel floor plate made from HARDOX-450 steel or equivalent, 4 x 3 t lashing rings on each side flush-mounted in external frame in accordance with UVV) * Support load: 3 t Cpodpfx Asv D Tb Regwew * Tyres: 600/55/R22.5 * Subject to errors and prior sale * Trailer is in very good / as-new overall condition