Çalışma platformlu römork

MÜLLER-MITTELTAL 3-Achs Plateau, luftgefedert, hydr. Rampen

Durum: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * PT 30 Profile: ----Braking system: * EBS (Electronic Braking System) * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering system as well as RtR valve ----Drawbar: * Drawbar, 1,200 mm long, with 40 mm towing eye and adjustable height via tension spring and turnbuckle ----Electrics / Lighting: Ljdpfxexptn Re An Tern * Smart-Board mounted on the trailer as an information tool (axle load display – front and rear separately) * Tire pressure monitoring system with display option in the truck via EBS signal (no installation required on the truck side) * 15-pin power connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear ----General attachments: * Side underrun protection * Swivel support legs at the rear of the chassis frame * Mechanically adjustable warning sign packages at front and rear * Stainless steel/polymer quarter mudguards with splash protection at the front axle * Straight galvanized steel mudflaps with splash protection at the rear axle * Tool box made of galvanized steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted right-hand side * Compartment in the bogie with folding lid for accessories, 2 fixed container locks (directly behind the bogie platform) * 2 galvanized steps on the bogie, left and right ----Low-bed platform: * ROBOT-welded anti-slip coating on the steel plate of the bogie platform (bead welds left proud) ----Load securing (load securing package consisting of): * 2 lashing eyes (13.4 t) front left and right at the front wall support * 1 pair of UVV lashing rings (13.4 t) at front and rear, plus 3 pairs per side of UVV lashing rings (10 t) – swiveling and lowerable, loadable in all directions and integrated into the outer frame * 3 stake pockets per side, each with a 2 t lashing option * Profifix lashing rail along the longitudinal centerline, in flat section, for lashing up to LC 3000 daN ----Widening: * 6 pairs of mechanical folding outriggers for up to 3 m overall width (not in the rear bevel) * Widening planks stored in the middle of the loading area ----Ramps: * Hydraulic one-piece loading ramps, approx. 3,000 x 720 mm * Mechanically laterally adjustable * 4-way valve block for possible retrofitting of hydraulically shifting ramps ----Excavator arm trough: * Continuous excavator arm trough from rear axle to end support (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN integrated in the excavator arm trough at the longitudinal frame ----Loading height: * Approx. 910 mm, +/- 20 mm with air suspension, loaded ----Paintwork: * Chassis, bogie, folding outriggers, drop-down supports, and ramps hot-dip galvanized * Axles, slewing ring, air tanks, drawbar painted in a black tone ----Information: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Durum: ikinci el, boş ağırlık: 10.900 kg, azami yük ağırlığı: 43.600 kg, toplam ağırlık: 54.500 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 04/2025, yükleme alanı uzunluğu: 8.700 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 855 mm, lastik boyutu: 245/70 r17.5, renk: gri, Üretim yılı: 2025, işletme ağırlığı: 10.900 kg, Donanım: ABS, Gooseneck, rigid, central tube design: - Enclosed outer frame with cut-outs for lashing straps (LC 1,500 daN) - Steel floor covering with anti-slip coating - Including perforated rail for aluminium approach ramps - 2" king pin - Mechanically operated BPW landing legs - 550 mm long, 8° incline at the gooseneck end - Front wall including storage position for rear wall, 400 mm high - Spare wheel holder mounted upright at the front of the gooseneck - 3 pairs of recessed lashing rings LC 5,000 daN in the loading area of the gooseneck - Aluminium drop-in side walls, 400 mm high, consisting of 2x side walls (3,150 mm length) and rear wall with stanchions (galvanised) - Storage box rectangular, aluminium, folding lid, lockable, approx. 400 x 800 mm, centre - Storage box 45’, aluminium, folding lid, lockable, approx. 400 x 800 mm, left - Storage box 45’, aluminium, folding lid, lockable, approx. 400 x 800 mm, right Loading platform, single extendable: - Enclosed outer frame with cut-outs for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Sheet metal floor covering with anti-slip coating - Angled interface between fixed section and loading platform for bridging rails and wheel recesses - Excavator recess including longitudinal slots for cargo securing (LC 1,500 daN), approx. 3,850 mm length - Preparation for hydraulic ramp (electrical supply) - Outriggers for widening to 3,000 mm - Angled vehicle rear, 8°, 550 mm long - Sled design for easy installation and removal of ramps - Continuous mud flap at the rear - 1 pair of lashing points LC 10,000 daN centrally located on loading platform behind gooseneck - 7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform - 6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform - 1 pair of lashing points LC 10,000 daN centrally at the rear of the loading platform - 1 pair of stanchion pocket rails approx. in the centre of the loading platform - 1 pair of stanchion pocket rails on the fixed section - 1 pair of stanchion pocket rails behind the last axle Ramps: - Hydraulic split folding ramps, 2,750+1,500x800 mm - Larch wood covering - Remote control operation (wired and wireless options) - Ramps with quick-change (dismantling) system Chassis: - Axle make: BPW ECO Max - 2 ride heights - 4 axles at 10 t each (technically 12 t) - Twin tyres 245/70 R17.5 - 2 x rigid axle and 2 x friction-steered axle - Reverse steering lock for friction-steered axle by engaging reverse gear - Brake system: Knorr brand (according to EU regulations with EBS-E) - TIM G2 from Knorr (Trailer Information Module) - RSS (Roll Stability Support) - Load-dependent lift axle on the first axle including starting aid (forced lowering of the lift axle via TIM possible) Accessories: - 4 wheel chocks with holders - 2 pairs of warning boards 423 mm x 423 mm, with 2 position lights and socket for beacon, infinitely adjustable up to 3,950 mm Lredpfei Ai E Rex An Tsn - Lashing options at gooseneck and on loading platform (alternatively on ramp, if present) included - Removable splash plate at the end of the excavator recess - Electro-hydraulic unit for ramp operation - Wireless remote control for ramp operation - Hydraulic support legs at vehicle rear for support during loading - 1 pair additional reversing lights at rear, activated with reverse gear - Wooden broadening planks – larch (option)

Durum: yeni, azami yük ağırlığı: 36.020 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, süspansiyon: hava, lastik boyutu: 435/50 R 19.5, renk: gri, Donanım: ABS, Cargo Area: - Extendable cargo area design with pneumatically actuated locking - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - Cut-outs in the external frame of the cargo area for securing belts Lrsdpfx Aei Dwlwjn Ton Axles and Tyres: - BPW axles, air-suspended, with disc brakes (377 mm), height adjustment function (raise/lower) - Self-steering axles with electromagnetic reversing lock, activated via reverse gear or manually - Axle tools included - Tyres: 435/50 R 19.5 Brake System: - Brake system compliant with EU regulations, with EBS-E (2S2M) Paintwork: - First-class, long-lasting corrosion protection for the standard shot-blasted welded frame, ensured by a two-component zinc dust primer (2K) - High-quality single-tone two-component topcoat (2K) in Novagrau - Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint not possible Landing Gear: - JOST landing gears (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel Construction: - Steel construction from high-tensile fine-grain steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system compliant with EU regulations, 24 V ASPÖCK-NORDICK (ASS3) lighting - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S and 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories Included: - Yellow-red air couplings on the galvanized front connection panel - 2 wheel chocks with brackets - 2" king pin - Galvanized steel front wall approx. 1,600 mm high - Yellow reflector tape according to EU regulations on the sides, extension, and rear of the trailer - European reflective plates (red-yellow) at the rear of the trailer - Cargo floor made of approx. 38 mm thick hardwood - 10 pairs of stake pockets for 100 x 50 mm plug-in stakes integrated in the external frame of the cargo area - 1 spare wheel holder under the cargo area on the right in driving direction - Manual and documentation on USB stick - 1 mud flap at the rear of the trailer - 1 bracket for a beacon at the rear of the trailer - At the goose neck and on each side of the rear panel, 1 bracket for warning signs incl. socket - 1 INOX toolbox, crosswise under the cargo area (1,000 x 400 x 2,500 mm) - 6 pairs of WADER container locks in the cargo area for 1 x 20ft container, 2 x 20ft containers or 1 x 40ft container; an additional locking position in the extension for one 45ft container - 3 pairs of transverse stake pocket rails installed across the cargo area for 100 x 50 mm plug-in stakes - 60 km/h speed sticker at the rear - 2 reversing lights mounted on the rear panel - Four warning signs, extendable by approx. 400 mm (approx. 423 x 423 mm), with position light - Mounting bracket for beacon on the warning signs - HRM metalization (High Resistance Metallisation) of the external frame - Complete steel structure shot-blasted; then, the defined visible surfaces are metal-coated with ZINACOR 850 (zinc 85% - aluminum 15%) by thermal spraying

Durum: yeni, boş ağırlık: 10.600 kg, azami yük ağırlığı: 39.400 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 760 mm, süspansiyon: hava, lastik boyutu: 205/65 R17.5, renk: gri, işletme ağırlığı: 10.600 kg, Donanım: ABS, Swan-neck: - Swan-neck with 30 mm thick hardwood flooring - Swan-neck at the rear in straight design - 3 pairs of lashing rings (LC 5,000 daN) Extendable loading platform: - Loading platform in extendable version - 5 pairs of fold-out lashing rings - 3 pairs of fold-out lashing rings - 1 pair of horizontal lashing rings at the front of the loading platform - Cut-outs in the outer frame of the loading platform for attaching tension belts - Hardwood flooring approx. 48 mm thick, checker plate covering above the axles Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tyres: - BPW axles, two fixed and two steering axles Lrsdot Ag Uwspfx An Tjn - Air suspension, drum brakes, with lift/lower function - The steering axles can be locked electro-magnetically via reverse gear or manually - Axle tools - Tyres: 205/65 R17.5 Brake system: - Brake system according to EU regulations with EBS-E (4S3M) Steel construction: - Steel structure made of high-strength fine-grain steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations, 24 volt lighting, ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection strip, with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat, single colour in Nova grey - Rear section metallized and painted in RAL 9010 (pure white) Included accessories: - One spare wheel with holder located in front of the bulkhead - 2" king pin - Galvanized steel front wall approx. 400 mm high - Yellow-red air couplings on the front galvanized connection strip - 4 wheel chocks with holder at the bulkhead - Galvanized folding supports under the sloped part of the loading platform - Holder for rotating beacon at the rear of the trailer - Galvanized, extendable width extensions approx. 230 mm per side - White reflective tape according to EU regulations on sides, at extension section, and red at rear - On swan-neck and rear panel: one mount each for warning panels including socket (left and right) - European reflective warning boards (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system in accordance with ECE R 141 - On the swan-neck: removable ALU side panels and tailboard approx. 2,440 x 400 mm - The rear, galvanized stanchions are removable (length of superstructure approx. 2,560 mm) - 7 pairs of WADER container locks - 1x 20ft container on the loading platform; 1x 40ft container on the loading platform; 1x 40ft container over the swan-neck; 2x 20ft containers - 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the loading platform - Lift axle at the front axle, controlled by TEBS E in relation to current axle load and loading status - Sliding hook-in rail for ALU loading ramps at the rear of the vehicle - Sanded, anti-slip coating painted onto checker plate on swan-neck and loading platform - Four warning panels extendable by approx. 400 mm each, approx. 423 x 423 mm, with a position lamp - Mount for rotating beacon on warning panels - Speed stickers 80 km/h at the rear and on both sides - Load gauge to determine axle loads, including load chart

Durum: yeni, boş ağırlık: 7.900 kg, azami yük ağırlığı: 41.600 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, işletme ağırlığı: 7.900 kg, Donanım: ABS, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Lrjdpfx Aounrapen Ten Loading Area: - Loading area with rear bevel approx. 1,000 mm x 8° - Recess in the bevel and extending into the loading area for accommodating the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm - Cut-outs in the outer frame of the loading area for attaching tensioning straps - Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Landing Gear: - JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity 24 t (test load 50 t) Axles and Tyres: - BPW axles and suspension, 2 fixed axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear and manually - Air suspension with lift and lower valve - TPMS tyre pressure monitoring system as per ECE R 141 - Tyres: 235/75 R 17.5 Paintwork: - Complete steel structure automatically blasted with shot blasting machine after welding - Second blasting with corundum for optimal coating adhesion - Final painting with 2 coats of 2K topcoat, single colour RAL MB 7350 Novagrau - Rims painted silver - Rear section metallised and painted RAL 9010 (Pure White) - Cavities sealed with special wax Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connection bar with sockets: 2 x 7-pin & 1 x 15-pin Accessories Included: - Numerous lashing positions - 2" king pin - One galvanised steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanised front connection bar - 4 wheel chocks with holder on the front wall - Holder at the rear of the gooseneck for ALU loading ramps - Galvanised folding support legs under the rear bevel of the loading area - Holder for rotating beacon at the rear of the trailer - Galvanised, extendable widenings approx. 230 mm per side - White reflective tape to EU regulations on the sides, red at the rear - Holders for warning panels with socket at the gooseneck and rear crossmember, left and right - Removable ALU sideboards and rear board on the gooseneck, approx. 2,440 x 400 mm - Removable rear galvanised stakes - 2 pairs of WADER container pockets in the loading area for a 20ft container - 6 pairs of post pockets (for 100 x 50 mm stakes) in the outer frame of the loading area - Movable mounting bar for ALU loading ramps at the rear of the vehicle - 20 x 20 mm square climbing strips every 200 mm on the outer frame of the loading area bevel - Anti-slip sand coating applied to checker plates on gooseneck and loading area - Four extendable warning signs, approx. 400 mm extension, size 423 x 423 mm, each with a position light - Bracket for rotating beacon on the warning signs - 80 km/h speed stickers at rear and on both sides - European reflector panels (red/yellow) at rear of trailer - Manual and operating instructions on USB stick - HRM metallisation (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then all defined visible surfaces hot-finish metallised with ZINACOR 850 (zinc 85% - alu 15%)