Çalışma platformlu römork

MÜLLER-MITTELTAL T4 40,0 , Agrar, hydr. Rampen,3 m. Paket

Durum: yeni, azami yük ağırlığı: 31.630 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle equalization front and rear * Tire pressure monitoring with display capability in the truck via EBS signal – no truck-side installation required * Warning sign packages front & rear * Reflective contour tape on sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon at the rear * 24 V - 15-pin and additionally 12 V - 7+4-pin power cable * Extended connection lines for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel carrier in basket design, right side * Enclosed single plastic mudguards at the front * Straight rear steel splash guards each with spray suppression * Side underrun protection * Extended offset cranking by 500 mm to the front * Turntable platform extended by 520 mm at the front with 45° corners and 3 recessed, lockable storage compartments including covers * Chassis made of high-strength fine-grained steel * Floor over the turntable platform made of 50 mm softwood, in the lowbed platform 60 mm softwood * Outer planks of the access ramps made of 50 mm bamboo wood * Four stake pockets on each side (stakes not included) with simultaneous 2 t lashing capacity * Lashing package consisting of: 2 lashing rings 6.4 t at the front left and right on the main frame of the turntable platform, each 1 pair 13.4 t lashing rings front and rear on the outer frame, and additionally 4 pairs 10 t swivel and lowerable lashing rings per side, loadable in all directions and recessed in the outer frame, 2 pairs 6.4 t lashing rings sideways at the excavator stick holder, 8 pairs galvanized folding extensions for 3 m total width (not including rear slope) * Widening planks stored in a side locker on the left Redpfel Th Evjx Ahhsw * Excavator stick holder above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * Mechanical rear supports * Hydraulic, hot-dip galvanized access ramps approx. 3,000 x 720 mm * Hydraulic side-shifting of ramps on sliding tube from ramp shaft * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded platform height approx. 860 mm (incl. 860 mm approach slope) * Chassis, turntable, access ramps, mechanical folding supports at rear hot-dip galvanized * Axles, springs, air tanks and turntable painted in black * New vehicle with manufacturer’s warranty * Errors and interim sale excepted * Available immediately from Egestorf

Durum: yeni, Fonksiyonellik: tamamen fonksiyonel, boş ağırlık: 7.500 kg, azami yük ağırlığı: 36.500 kg, toplam ağırlık: 44.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.190 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 900 mm, süspansiyon: çelik-hava, lastik boyutu: 235×75 R17,5, dingil mesafesi: 1.310 mm, Üretim yılı: 2024, Donanım: ABS, merkez döner tabla, CETRATEK 4-Axle Low Loader TL89.4 (EU-COC) Rsdpfx Aju Rbzvjhhew Short Description Robust low loader for heavy machinery transport. Frame constructed from high-strength ST-52/S355 steel, with optional fine-grained steel S700. Each ramp supports up to 20 t load, can be folded mechanically or hydraulically without loss of capacity. Optionally available as a low-bed version, with loading height in the wheel recess area adjustable from approx. 900 mm down to approx. 500 mm. Dimensions / Construction Overall length: 11,914 mm, overall height: 3,775 mm (over ramps) Platform: Gooseneck 2,440 mm + loading area 6,750 mm Width: 2,540 mm (manually extendable by 250 mm on each side) Coupling to 1st axle: 2,767 mm, to 2nd/3rd axle: 6,136 mm Axle spacing: front 1,310 mm, rear 1,360 mm Platform height: 900 mm (low-bed approx. 500 mm), track width 1,850 mm Rear ramps: 3,000 × 750 mm, laterally adjustable, 20 t per ramp Drawbar eye height: 400–900 mm; turntable Ø 110 mm (CYR) Floor: steel + 45 mm hardwood (hornbeam), coated for protection Weights / Capacity a) GVW 44,000 kg → Payload approx. 36,500 kg* b) On-road 24,000 kg → Payload approx. 16,500 kg * Version a) requires a special permit according to §70 StVZO; appraisal/DEKRA inspection available at extra cost. Drawbar eye Ø 50 mm (optional Ø 40 mm), unladen weight approx. 7,500 kg Rear supports: manual (hydraulic option available) Steel Structure / Chassis Welding qualification TS EN ISO 9606-1, processes TS EN ISO 4063, shielding gases TS EN ISO 14175 4 × 11-t axles (TRAX), tyres 235/75 R17.5 (16 pcs., PETLAS or equivalent; Continental/Michelin available at extra cost), rims 6.75×17.5, air suspension, approved up to 100 km/h Brakes / Electrics WABCO EBS 4S/2M, linings 330×200, air tanks 2×80 L + 1×60 L Brake cylinders: 4× type 24 + 4× type 24/30, levers 165 mm Voltage: 24 V (voltage converter required with 12 V towing vehicle) Side reflectors: 4× LED per side + 2× white front reflectors, rear lights 2× LED, 2× triangular reflectors Connections: 7-pin EBS ISO 7638, 7-pin ISO 1185/3731, 15-pin ISO 12098 Tractor operation notice: 12→24 V converter as well as ABS/EBS connection (ISO 7638) and power supply (e.g., ISO 1185/12098) required for on-board hydraulics. Hydraulics (Ramps) 2 cylinders, including changeover valve to use tractor unit’s on-board hydraulic system Accessories (extract) 2 toolboxes, 2 wheel chocks (metal), fire extinguisher box Reflectors (side white/yellow; extensible yellow/red), rectangular rear reflectors Lashing eyes: 7 per side + 6 on the platform (10 t each) Mud flaps (front/rear), hose/cable holders on the drawbar Paintwork Sandblasted, 3× epoxy primer, 3× acrylic (≈ 230 µm), 1× acrylic clear coat Warranty 2 years on frame structure and axles (excluding accidents/operator error) 2 years on electrical & braking system (excluding wear parts such as brake pads, accidents/operator error) 1 year on paintwork (excluding accidents/operator error) Technical specifications and prices subject to change without notice. Images for illustration purposes only and may include optional features.

Durum: ikinci el, azami yük ağırlığı: 31.000 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 07/2024, yükleme alanı uzunluğu: 9.290 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 950 mm, * PT 40.0 Profi ----Brake System: * Wabco EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and adjustable height ----Lighting / Electrics: * EBS multi-voltage system with 12 & 24 V wiring * 15-pin power connector * LED lighting system 12 / 24 V * Removable LED beacon at rear * 2 LED reversing lights (activated via reverse gear) ----General Attachments: * Manometer – pressure gauge for payload determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front and rear * Front axle: plastic quarter mudguards with splash protection * Rear axle: straight galvanized steel skirts with splash protection * Reflective contour tape on sides and rear * Tool box made of galvanized steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low Loader Platform: * Forepart in front of the turntable platform approx. 490 mm long with 45° corners * Robot-welded anti-slip coating on the turntable platform steel deck * Hardwood flooring on running surfaces of the low loader platform ----Load Securing (La-Si Package, consisting of): * In front of the bulkhead carrier left & right, each with 1 x 13.4 t UVV lashing ring * Four holes per side in the turntable platform, each with 2 t lashing capacity * 1 pair of 13.4 t lashing rings suspended at the rear left & right in front of the rear crossmember * Four pairs per side of 10 t foldable and lowerable UVV lashing rings, loadable in all directions, integrated into the outer frame * Three stake pockets per side, each with 2 t lashing option ----Widening Package: * Hot-dip galvanized mechanical folding outriggers for 3 m total width (not in the sloping rear) * Board holder for extensions mounted longitudinally under the chassis on the left ----Excavator Arm Rest: * Excavator arm rest from rear axle to end crossmember, approx. 2,100 mm long and approx. 190 mm deep * Two pairs per side of 6.4 t lashing rings in the excavator arm rest ----Ramps: * Single-piece hydraulic loading ramps (approx. 3,000 x 720 mm), mechanically adjustable side-to-side * Outer boards of the loading ramps made of hardwood * Steel structure prepped for 6-way control valve ----Loading Height: * Unladen loading height approx. 950 mm +/- 20 mm ----Tyres: * Tyres 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical drop-down supports, and loading ramps hot-dip galvanized * Axles, air tanks, and drawbar painted in black ----Information: * Vehicle has a day registration dated 07/2024, due to the missing tire pressure monitoring system and has not been loaded or used * New vehicle with manufacturer's warranty * Subject to prior sale and errors ----Delivery Time: Rsdpfx Ahel Tlhrohew * Immediately available ex Egestorf

Durum: yeni, boş ağırlık: 7.500 kg, azami yük ağırlığı: 32.500 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, bir sonraki muayene (TÜV): 03/2023, yükleme alanı uzunluğu: 9.700 mm, yükleme alanı genişliği: 3.000 mm, yükleme alanı yüksekliği: 900 mm, süspansiyon: hava, lastik boyutu: 235/75r17,5, Üretim yılı: 2026, Donanım: ABS, merkez döner tabla, TOP SPECIFICATION => INCLUDING THE FOLLOWING EQUIPMENT: - Chassis frame hot-dip galvanized in immersion bath - Front storage compartment at the top of the platform, with hinged lid - Rear storage compartment at the top of the platform, with hinged lid - Recess for excavator arm support in the rear area of the low-bed - 3 m equipment package without slope - Warning package for special permit - Steel sheet toolbox - Stake pocket package in the outer frame - Basic hydraulics for truck with rear connection - Hydraulic ramp lifter for one-piece ramps - Hydraulic lateral ramp shift - Hydraulic support legs left and right - 1 pair of lashing rings (6 t) in the outer frame, bolted - WABCO SmartBoard configured Rjdpfoglbllsx Ahhsw - SSV complete, front left HTD409525K - COC paperwork OPTIONAL - Rubber flooring on the ramp: €1,890 net - Rubber flooring on the slope: €1,250 net - Swivel drawbar 40 / 50 DIN

Durum: ikinci el, azami yük ağırlığı: 31.000 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 07/2024, yükleme alanı uzunluğu: 9.290 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release mechanism for spring-loaded cylinders Redpel Tnu Asfx Ahhew * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lifting and lowering function and RtR valve ----Drawbar: * Drawbar with 50 mm towing eye and height adjustment ----Lighting / Electrical System: * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable LED beacon at the rear * 2 LED reversing lights (switched by reverse gear) ----General Attachments: * Manometer - pressure gauge for determining load weight (axles separated over 2 air suspension circuits) * Side underrun protection * Swing-out supports at rear of chassis frame * Mechanically adjustable warning board sets front and rear * Front axle plastic quarter mudguards with spray protection * Rear axle straight galvanized steel mud flaps with spray protection * Reflective contour tape on sides and rear * Toolbox, black powder-coated galvanized steel, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low Loader Deck: * Extension in front of turntable platform approx. 490 mm long with 45° corners * ROBOT-WELDED anti-slip covering on steel plate of the turntable platform * Hardwood flooring on running surfaces of the low loader deck ----Load Securing (load securing package includes): * In front of the front wall carrier left & right, 1 x 13.4 t UVV lashing point each * 4 holes per side in the turntable platform, each with a lashing capacity of 2 t * 1 pair of lashing points (13.4 t) suspended at the rear left & right in front of the rear cross member * Per side 4 pairs of UVV lashing rings (10 t), swiveling and lowerable, loadable in all directions and recessed into the outer frame * Per side 3 stake pockets, each with a simultaneous 2 t lashing option ----Widening Kit: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (except at the rear bevel) * Plank holders for extensions under the chassis, left side in longitudinal direction ----Excavator Arm Rest: * Excavator arm rest over the rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 t lashing points per side in the excavator arm rest ----Ramps: * Hydraulically operated, one-piece drive-on ramps (approx. 3,000 x 720 mm), mechanically adjustable sideways * Outer planks on the ramps made of hardwood * Steel construction prepared for 6-function slider valve ----Loading Height: * Loaded edge (unladen) approx. 950 mm +/- 20 mm ----Tyres: * Tyres 235/75 R 17.5 ----Paintwork: * Chassis, turntable frame, folding outriggers, mechanical drop supports, ramps galvanized * --Axles, air tank, drawbar painted in black tone-- ----Info: * Vehicle has a temporary registration in 07/2024 due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Availability: * Immediately available from Egestorf