Alçak yükleyici yarı römork

Goldhofer 4-Achs-Tele-Semi-Anlegerampen-zwangsgele

Gooseneck, rigid, in central tube design:
- Front corners 45°
- Closed outer frame with cut-outs for lashing straps (LC 1,500 daN)
- Punch strip for aluminum drive-on ramps
- 2" king pin
- Mechanically operated BPW landing legs, right side in direction of travel
- 550 mm long, 8° bevel at the end of the gooseneck
- 3 pairs of recessed lashing rings LC 5,000 daN in the gooseneck loading area

Loading platform, single telescopic:
- Closed outer frame with cut-outs for lashing straps (LC 2,000 daN)
- Beveled interface between fixed section and loading platform for mounting bridging rails and wheel recesses
- Technically maximal extension of 6,840 mm
- Beveled vehicle rear 8°, 550 mm length
- Slide-out ramp system for easy mounting/dismounting of ramps
Ndsdpfexqyyvox Aayoc
- Mechanical, spring-assisted comfort drop-leg supports at the vehicle rear for stabilizing during loading processes

Drive-on ramps:
- Load capacity per pair 32 t
- Ramp width 600 mm
- Ramp length 2,400 mm

Chassis:
- BPW ECO Max axles, air-suspended
- Twin tyres 225/60 R17.5 with 10 t axle load, HBI
- 1 x rigid axle and 3 x forced steered axles
- Maximum steering angle approx. 45°
- Brake system by Knorr (compliant with EU regulations with EBS-E)
- TIM G2 by Knorr (Trailer Information Module)
- Roll Stability Support (RSS)
- Standard second loading height at 820 mm (-100/+100)
- Steering operation via wireless remote control or button on the gooseneck, including tracking alignment function
- Load-dependent lift axle on the first axle including starting aid (forced lowering of lift axle via TIM possible)
- Tyre pressure monitoring system (TPMS) by Knorr, with rim-mounted sensors

Accessories:
- Front wall incl. parking position for rear wall, 400 mm high
- Spare wheel carrier on gooseneck + 2x spare wheels
- 1 pair wheel chocks incl. holder
- Extension beams to widen to 3,000 mm
- Aluminum plug-in sideboards 400 mm high, consisting of 2x side boards, length 3,150 mm, and rear board with stanchions (galvanized)
- Aluminum 45° toolbox with folding lid, lockable, approx. 400 mm x 800 mm x 380 mm, left side
- Rectangular aluminum toolbox with folding lid, lockable, approx. 400 mm x 800 mm x 380 mm, center
- Aluminum 45° toolbox with folding lid, lockable, approx. 400 mm x 800 mm x 380 mm, right side
- 2 pairs warning boards 423 mm x 423 mm, with 2 position lights and mount for rotating beacon. Fixing options on gooseneck / cranked section and on loading platform
- 1 pair of stanchion pocket rails on rear of gooseneck and 1 pair at the front as positive-locking restraint
- Mounting rail for aluminum ramps on gooseneck
- 2 pairs of adapter pieces to extend warning boards up to 4,500 mm
- Extensive lashing points
- 7 pairs of stanchion pockets 100 x 50 mm in the outer frame of the loading platform
- Long material support for 20 t
- 1 pair of closed plastic toolboxes (left and right under loading platform), width 700 mm
- Open steel toolbox for extension planks and drive-on ramps, mounted under loading platform, width 1,600 mm (max. payload 400 kg with even load)
- 4 pairs of container locks for transport of 2 x 20ft or 40ft containers on the loading platform
- Lateral climbing strips on rear bevel
- Sliding rail for attachable ramp at vehicle rear
- Central lubrication system

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.