Alçak yataklı yarı römork inşaat makinesi taşımak için

Faymonville MAX Trailer 3-A-Tele-Semi-Rampen-zwangs.

With every used semi-trailer, you receive a current and complete inspection and function report.

Gooseneck:
- Gooseneck with rear taper approx. 750 mm x 10°
- 3 pairs of lashing rings (LC 5,000 daN)
- 30 mm hardwood flooring

Extendable load area:
- Extendable load area with rear taper approx. 1,000 mm x 8°
- 5 pairs of outside foldable lashing rings (LC 5,000 daN)
- 3 pairs of outside foldable lashing rings (LC 10,000 daN)
- 1 pair of horizontal lashing rings in the front load area (LC 10,000 daN)
- Cut-outs in the outer frame of the load area for attaching tension belts (LC 2,000 daN)
- Hardwood flooring approx. 48 mm thick, over axles covered with checker plate

Ramps:
- One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering
- Ramp with hydraulically extendable and retractable sections, hydraulic lifting system, hydraulically adjustable
- Maximum load per pair: 40,000 kg

Axles and tires:
- BPW axles and suspension, all axles hydro-mechanically forced-steered
Rbodpsyx E E Aefx Ad Tjw
- Technical axle load: 12,000 kg
- Air suspension with lift/lower valve
- Axle tool kit
- Tyres 235/75 R 17.5

Accessories included:
- 2" king pin
- Galvanized steel front wall, approx. 400 mm high
- Yellow-red air couplings at the galvanized connection strip in front
- 4 wheel chocks with holders
- One spare wheel with holder in front of the front wall
- Electro-hydraulic power pack
- Remote steering from front and rear via cable remote controller with pushbuttons, with single-track axle control
- Rear mount for ALU ramp adapters in the gooseneck
- Holder for warning signs on the gooseneck and ramps, left and right, including socket
- Galvanized folding supports under the taper of the load area
- Control valves for ramps mounted on the right-hand side of the semi-trailer
- Cover plates to bridge the gap between ramps and load area
- Removable ALU side boards and rear board on the gooseneck approx. 2,440 x 400 mm
- Rear galvanized plug-in stakes are removable (body length approx. 2,560 mm)
- 4 pairs of WADER container pockets in the load area for 1x 20ft, 2x 20ft, 40ft or 1x 45ft container
- 7 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the load area
- Galvanized width extensions, extendable by approx. 230 mm per side
- One INOX toolbox 1,500x390x810 mm mounted under the load area on the right side in direction of travel
- 20x20 mm square climbing bars every 200 mm on the outer frame in the tapered area of the load area
- Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition
- BEKAMAX (Pico) centralized lubrication system with standard grease NLGI-2
- Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with a position light
- Wireless remote control for rear steering in addition to cable remote, with status indicator lights on the receiver for single-track control
- Coated sand layer on the checker plate, over the king pin and load area as anti-slip protection
- 80 km/h speed stickers on the rear and both sides
- Load pressure gauge for determining axle loads including load diagram
- HRM metallization (High Resistance Metallisation) of the outer frame
- Entire steel structure shot-blasted, then all defined visible areas are metalized with ZINACOR 850 (85% zinc - 15% aluminum) by hot spray finishing.

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.