Çalışma platformlu yarı römork

MÜLLER-MITTELTAL 3-Achs Satteltieflader überfahrbar m. Radmulden

Durumu: yeni, azami yük ağırlığı: 37.500 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2024, * TS 3 RM 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring-actuated cylinders Hsdpfx Ael Tiiyogcsw * Drum brakes * 3 x 11 t BPW axles * Air suspension with lift/lower device and Ride-to-Release valve * Last axle self-steering with electro-pneumatic steering lock * Side underrun protection * Landing gear at front and swing-down supports at rear of chassis * 15-pin electrical connector * LED tail lights * Mechanically adjustable warning panel sets, front and rear * Rotating beacon (removable) at rear left * Straight steel sheet fenders * Spare wheel holder in front of bulkhead cross member (without spare wheel) * Saddle platform with front corners chamfered at 45° and front toolbox made of galvanized, powder-coated sheet steel, W = 2,480 mm x H = 500 mm x L = 665 mm, with hinged lid * 400 mm aluminum side panels (RAL 9010), fold-down and removable, mounted on sides of the saddle platform * Rear wall inserted, height 150 mm * Rear slope on the saddle platform to the low bed approx. 700 mm long, each with 1 recessed lashing ring * Saddle platform with 50 mm clamped hardwood planks and low-bed platform with 60 mm clamped hardwood planks * Tread plate above the axles * 9 x mechanical folding extensions to 3 m overall width (no extensions in rear slope area); extension planks supplied with enclosed transverse stowage compartment under the loading area * 2 lashing bars recessed into the outer frame of the saddle platform on each side; 3 lashing rings per side in the low-bed platform plus 1 additional centered lashing ring at the rear cross member; 2 x 5 t lashing rings per side, bolted at the lower outer frame of wheel recesses * 2 x 6.4 t UVV-compliant lashing rings per side in the excavator arm trough * Excavator arm trough runs continuously from the end of the last rigid axle over the steering axle to the rear cross member, with internal reinforcement, approx. L = 2,450 mm x W = 770 mm x D = 270 mm * 2 wheel recesses per side, 390 mm deep and 640 mm wide, with slide-in covers for transporting wheel loaders with wheelbases from 3,120 - 3,620 mm; front recess slopes up from 1,100 mm at the bottom over a length of 2,050 mm, rear recess slopes up from 580 mm at the bottom over a length of 1,550 mm * Hydraulic folding ramp with extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic lateral ramp adjustment * Outer board on the ramp made of 50 mm hardwood * Load area above turntable: approx. 3,950 x 2,480 mm * Unladen loading height: approx. 1,470 mm * Lower loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (including 860 mm ramp slope) * Chassis, rear swing-down supports, ramps, mechanical folding extensions are hot-dip galvanized * -- Axles, springs, air tanks painted in black tone -- * Suitable for 2- and 3-axle tractor units * Coupling height: approx. 1,220 mm * Tires: 235/75R17.5 * Technically permissible gross weight: 48,000 kg * Vehicle is hot-dip galvanized * Side panel painting in RAL 9010 pure white * Other RAL colors for the side panels available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available immediately ex Egestorf