Alçak şasi dorse

FAYMONVILLE F-S42-2GXX | MEGAMAX*auszieh. & verbreiterbar

Durumu: yeni, boş ağırlık: 17.500 kg, azami yük ağırlığı: 43.500 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.750 mm, yükleme alanı yüksekliği: 400 mm, lastik boyutu: 245/70 R 17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and removable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, “SUPER LOW” design, length approx. 7,550 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking - Supply lines routed protected inside the extendable beams and automatically adjust to the respective lowbed length Rear running gear: - Rear running gear with closed outer frame, chequer plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at rear - 2 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame Axles and tyres: - “PENDLE-AXLE”, all axles forced-steered by hydromechanics - Burst protection valve on axle compensation cylinder with automatic RESET feature - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres / 3PMSF Accessories included: Hjdpfx Ash Hm Theg Uoh - Prepared for mounting attachable container positions for 1x 20ft or 1x 40ft container on the outer beams - 2'' king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with bracket - At the galvanized front connection strip: yellow-red air couplings - 4 wheel chocks - Remote steering from front and rear by cable remote control with push buttons, including track alignment monitoring for the axles - Hydraulic couplings from gooseneck to lowbed with multi-coupling system instead of screw couplings - Electro-hydraulic unit - White reflector tape according to EU regulations on the sides, extension, and red at the rear - 2 wooden blocks 500x250x200 mm - European reflector plates (red-yellow) at the rear of the trailer - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps for NLGI-2 standard grease - Load pressure gauge to determine axle loads, including load chart - On the gooseneck, plug-in ALU side and rear walls approx. 2,000 x 400 mm - The rear galvanized plug-in posts are removable (body length approx. 2,120 mm) - Separate air connection with air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps to bridge the mountings of the lowbed - Four extendable warning signs approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for the steering in addition to the cable remote, with indicator lights on receiver for track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beam for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Folding extensions, approx. 230 mm per side - Anti-slip sand layer painted on the loading platform - Dipper recess on the rear running gear closed at the front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (Zinc 85% - Alu 15%)

Durumu: yeni, boş ağırlık: 12.900 kg, azami yük ağırlığı: 34.100 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.850 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 350 mm, süspansiyon: diğer, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 12.900 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,750 mm long - Gooseneck hydraulically height-adjustable and detachable - Technical fifth wheel load: 23,000 kg - Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading Platform: - Low bed with external beams in extendable "SUPER LOW" design, length approx. 6,850 mm - Low bed with fixed hardwood floor approx. 40 mm thick and mechanical locking Rear Chassis: - Rear chassis with closed outer frame, checker plate covering and continuous prismatic excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings foldable outward - 1 pair of lashing rings lying in the trough - 2 pairs of stake pockets for plug-in stakes (100 x 50 mm) in the outer frame Pendulum Axle and Tires: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-insert to secure in lifted position - Final coating of axles with 2 layers of single-color 2K paint, painted in "FAY-Grey-34-0260" - Technical axle load: 12,000 kg Hodpfx Ashlz R Sog Ush - Hydraulic axle compensation - Tires 245/70 R17.5 - TPMS (Tire Pressure Monitoring System) compliant with ECE R 141 Accessories: - Prepared for fitting of bolted container locking positions for 1x 20ft or 1x 40ft container on the external beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel - On the galvanized connection strip at the front: yellow-red air couplings - 4 wheel chocks - Remote steering front and rear operable via cable remote control with push buttons, including single-track monitoring of the axles - Hydraulic connections from gooseneck to low bed with multi-coupling instead of threaded couplings - Electro-hydraulic unit - White reflector tape on sides, extension and rear, according to EU regulations - European reflector panels (red-yellow) at the rear of the trailer - At the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting of bolt-on RUD rings VLBG-4 - Removable ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized plug-in posts are removable (body length approx. 2,560 mm) - Gooseneck at the upper rear area closed with a removable cover - 5 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading platform - Fold-out extensions, approx. 230 mm per side - 2 pairs of bolt-on RUD rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the low bed’s mounting hooks - Sanded layer painted on the loading platform as an anti-slip coating - Speed stickers 80 km/h on rear and both sides - Rear chassis’ bucket recess at the rear closed with a plug-in plate - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm - Radio remote control for the rear steering, in addition to the cable remote control, with indicator lights on the receiver as single-track monitoring - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determining axle loads - HRM (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces hot-finished in metallization with ZINACOR 850 (Zinc 85% - Alu 15%)

Durumu: yeni, azami yük ağırlığı: 33.750 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including units immediately and short-term available, on our website. Extract from the equipment list. Full specification available upon request. Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - Compatible with tractor units: 4x2, 6x2, and 6x4 Lowbed: - Lowbed with external beams, extendable SUPER LOW design, approx. 6,850 mm length - Lowbed with fixed hardwood floor (approx. 40 mm thick) and mechanical locking - Supply lines protected within the extendable beams, automatically adapting to the lowbed length - 5 pairs of lashing rings, foldable to the outside (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Rear Chassis: - Rear chassis with closed outer frame, checker plate covering, and continuous prism-shaped excavator recess, approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable to the outside (LC 10,000 daN) - 1 pair of lashing rings recessed in the trough, LC 16,000 daN - 1 pair of lashing rings recessed in the trough, LC 10,600 daN - 2 pairs of stake pockets for removable stakes, approx. 100 x 50 mm in the outer frame Pendel Axles: - Pendel axles, all axles forced steered by hydro-mechanical linkage - Hose rupture valve on axle leveling cylinder with automatic reset function - Hydraulic cylinders with shut-off valves and pre-insert for securing in the lifted position - Axles painted with 2 layers of single-color 2-component paint in FAY Grey 34-0260 - Technical axle load: 12,000 kg each, with hydraulic axle compensation - Axle tools - Tyres: 245/70 R 17.5 3PMSF (brand at our discretion), load index (146/146F) TPMS: - TPMS tyre pressure monitoring system compliant with ECE R 141 Brake System: - Wabco braking system in accordance with EU regulations, EBS-E (2S2M) without connecting lines to the tractor unit Electrical System: - Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK lighting (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets, according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel Construction: - Steel structure made of high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Coating: - Complete steel structure is automatically shot-blasted after welding using a turbine blasting machine - Second blasting treatment with corundum for optimum coating adhesion - Full chassis metallized by HRM process with ZINACOR 850 (85% Zinc/15% Aluminium) for superior corrosion protection - Final coating: two layers of 2K topcoat, single-color in RAL 3002 carmine red, according to RAL system 841GL Including the following additional features: - 2-inch king pin - One galvanized steel headboard, approx. 400 mm high Hjdpsxbmn Ujfx Ag Ueh - Remote steering from front and rear via cable remote with pushbuttons, axle alignment control (without installation in the tractor unit) - Electro-hydraulic power unit - 2 pairs of bolted container locks on external beams, including 2 pairs of container locks for 1 x 20' or 1 x 40' container - On the gooseneck: detachable aluminium drop sides and rear wall, approx. 2,440 x 400 mm (LxH) - Rear galvanized removable stakes

Durumu: kullanılmış, renk: mavi, Üretim yılı: 2019, Faymonville F-S43-2GXX Baujahr: 2019 12 Tonnen Pendel-X-Achsen Eigengewicht: 12.560 kg Nutzlast: 48.440 kg Zulässiges Gesamtgewicht: 61.000 kg Sattellast: 25.000 kg Aluminium-Bordwände + Werkzeugkasten am Schwanenhals Hydraulisch abnehmbarer Schwanenhals 4,7 Meter ausziehbar 2 x 25 cm verbreitert, inkl. Verbreiterung Hydraulik des Anhängers funktioniert mit DUPLO-Elektrik Funkfernbedienung Verlängerungen: 5 Meter Hydraulische Federung 3 herausnehmbare Bodenplatten Baggerbrücke: 3950 x 700 mm 2 x Reserverad Abmessungen: Schwanenhals: Länge: 3.300 mm Breite: 2.480 mm Höhe: 1.550 mm Sattelhöhe: 1.250 mm Ladefläche: Länge: 7.850 mm Breite: 2.500 mm Höhe: 370 mm Bodenstärke: 220 mm Heck des Trailers: Länge: 3.950 mm Breite: 2.550 mm Höhe: 1.050 mm Bereifung: 245/70R17,5 (70 %) Top-Zustand! 2 Stück verfügbar! ID-Nr.: 283 Die Allgemeinen Geschäftsbedingungen der Firma Heinhuis gelten für alle Anzeigen, Angebote und Kostenvoranschläge von Heinhuis, alle von Heinhuis abgeschlossenen Verträge sowie die diesen vorangehenden Verhandlungen. Mit jeglicher Form der Kontaktaufnahme akzeptieren Sie die Geltung der AGB der Firma Heinhuis und bestätigen, dass Sie diese zur Kenntnis genommen haben. Unsere Preise sind Netto-Exportpreise. = Weitere Informationen = Hjdpox R Um Tofx Ag Ush Baujahr: 2019 Leergewicht: 12.560 kg Zuladung: 48.440 kg zGG: 61.000 kg Ausziehbarer Aufbau: Ja Preis: Auf Anfrage = Firmeninformationen = Für weitere Informationen: WhatsApp:

Durumu: kullanılmış, dingil konfigürasyonu: 3 aks, ilk tescil: 10/2010, yükleme alanı uzunluğu: 9.030 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 820 mm, toplam uzunluk: 13.850 mm, toplam genişlik: 2.540 mm, süspansiyon: hava, lastik boyutu: 205/65R17.5, dingil mesafesi: 8.630 mm, renk: kırmızı, Üretim yılı: 2010, Nooteboom MCO-50-04V 4 x steering axles. BPW axles. Remote steering with cable. Coupling height: 95 cm. Total length extended: 26.53 m. Load bed: 903 cm + 650 cm + 650 cm. Loaded loading height: 82.5 cm. = Further Information = Axle configuration Tyre size: 205/65R17.5 Brakes: Drum brakes Suspension: Air suspension Front axle: Twin tyres; Steered; Tyre tread depth left inner: 40%; Tyre tread depth left outer: 40%; Tyre tread depth right inner: 50%; Tyre tread depth right outer: 50% First intermediate axle: Twin tyres; Steered; Tyre tread depth left inner: 40%; Tyre tread depth left outer: 40%; Tyre tread depth right inner: 40%; Tyre tread depth right outer: 40% Second intermediate axle: Twin tyres; Steered; Tyre tread depth left inner: 50%; Tyre tread depth left outer: 50%; Tyre tread depth right inner: 50%; Tyre tread depth right outer: 50% Rear axle: Twin tyres; Steered; Tyre tread depth left inner: 50%; Tyre tread depth left outer: 50%; Tyre tread depth right inner: 50%; Tyre tread depth right outer: 50% Weights Hsdpsycqdksfx Ag Ujh Unladen weight: 14,960 kg Payload: 33,440 kg Gross vehicle weight: 48,400 kg Maintenance APK (Technical main inspection): valid until 11/2026 Identification Model number: MCO-50-04V / 2 X EXTENDABLE / 25 = Company Information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN), Wouter Greutink (NL-DE-EN-ES-IT), We speak Russian. We strive to provide accurate information, but no rights can be derived from the text provided.