Diğerleri

Hoeflon C4e Minikran

Durumu: kullanılmış, Üretim yılı: 2024, çalışma saatleri: 10 h, Donanım: her tahrikli, Hoeflon Mini Vinç C4e - Gösterim Cihazı Çok fonksiyonlu kompakt vinç İlk tescil: 16.05.2024 Kapasite: 2350 kg Maks. çalışma menzili: 11,7 m x 144 kg Maks. kaldırma yüksekliği (opsiyonlar dahil): 15,1 m Boyutlar U x G x Y: 2,8 m x 0,75 m x 1,82 m Boyutlar, vinç halatı ve bom dahil: 3,04 m x 0,75 m x 1,95 m Toplam ağırlık: 1.900 kg, opsiyonlarla 2.150 kg Direk sistemi: Silindir ve zincir sistemi Bom açısı: -5 - 83 derece Döndürme: 360 derece Sürüş sistemi: Uzaktan kumandalı 1. vites: 1,2 km/s 2. vites: 2,4 km/s Motor: Yanmar 3 silindirli, 1500 d/dk Eğim açısı: 20 derece Zemin basıncı: 0,59kg/cm2 Dahil olan özel donanımlar: Fly-Jib Vinç halatı: 3000 kg 30° ayarlanabilir uzatma parçası Katlanabilir destek ayakları Fpodstrh T Eepfx Ah Djc

Durumu: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, 3-axle MULTIMAX *PLUS low bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: * Loading platform width approx.: 2,540 mm Load height at max. payload approx.: 890 mm Suspension stroke approx.: -55/+145 mm Axle spacing: 1,360 mm *Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific regulations are exceeded. Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform, length approx. 9,600 mm with rear bevel approx. 900 mm x 6°. Loading platform behind gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating surface. Hydraulically foldable ramp tips. Ramps are individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward. Maximum load and approach angle as per technical data sheet: C470319 Maximum ramp angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift and lower valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF dual tyres. Manufacturer at our discretion. Load index 143/141J (144/144F) Brake system: WABCO EBS-E braking system according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" configuration according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation). Entire steel structure shot-blasted, then hot-dip refined with ZINACOR 850 (zinc 85% - alu 15%). Painting 6-coat final treatment: Whole steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion promoter. Topcoat with 2 layers of 2-component (acrylic) paint, single-color to RAL palette as chosen, followed by sealing the cavities with special wax. Rims in silver. Multi-color and custom painting available at extra charge. Steel construction: High-strength fine-grained steel construction. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa). Welders certified to DIN EN 287-1. MAG welding process per EN ISO 4063. Shielding gas M21 per EN ISO 14175. Front wall made of steel, removable, approx. 400 mm high. Fedeizu Ntopfx Ah Dspc Connection panel for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. 24N connection as per ISO-1185 24S connection as per ISO-3731 15-pin connection as per ISO-12098 If your pin assignment differs from the ISO standard, please inform us. "Anderson" socket on the front connection panel. Rema 78051-00 & Amp. 150 V. Cable for electric-hydraulic unit and/or electric winch (

Durumu: yeni, boş ağırlık: 10.350 kg, azami yük ağırlığı: 39.150 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of fixed built-in wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses equipped with 15 x 15 mm square climbing strips and lower-section extensions - 1 pair of fixed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm - 3-part removable galvanized covers over wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the ramp and extending into the load area to accommodate an excavator bucket arm approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm depression (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece ALU ramps: Fpedpoiu Er Asfx Ah Djc - One pair of single-piece ALU ramps approx. 2,500 x 600 mm - Ramps with spring assist and manual lateral adjustment - Maximum load per pair: 24,000 kg Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tools - Tyres 235/75 R 17.5 - TPMS (Tire Pressure Monitoring System) in compliance with ECE R 141 Accessories included: - One spare wheel with bracket in front of the bulkhead - 2" kingpin - One galvanized steel bulkhead ca. 400 mm high - Yellow-red air couplings at the galvanized front coupling strip - 4 chocks with bracket at the bulkhead - Accommodation at the rear of the gooseneck for ALU approach ramps - Galvanized extensions, extendable approx. 230 mm per side - Galvanized folding supports under the rear incline of the loading area - Bracket for a rotating beacon at the rear of the trailer - White reflector tape in accordance with EU requirements on sides, red on extension and rear - On the gooseneck and rear panel, bracket for warning boards including socket, left and right - On the gooseneck, plug-in ALU side walls and rear wall approx. 2,440 x 400 mm - Removable rear galvanized stanchions (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area - One removable galvanized intermediate table with 1 pair WADER container pockets - 20 x 20 mm square climbing strips every 200 mm along the outer frame of the loading area's rear incline - Non-slip sand coating painted onto the checker plate on the gooseneck and loading area - Four warning boards extendable by approx. 400 mm each, approx. 423 x 423 mm with position light - Bracket for rotating beacon on warning boards - 80 km/h speed stickers on the rear and both sides - Load gauge for axle load determination including load chart - HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces metallically finished with ZINACOR 850 (Zinc 85% - Alu 15%) hot metalized

Durumu: kullanılmış, Üretim yılı: 2024, çalışma saatleri: 10 h, Donanım: her tahrikli, Hoeflon Mini Crane C6 - Demonstration Unit First Registration: 30/04/2024 Fpjdpfei N U Dcex Ah Dsc Capacity: 3,000 kg Maximum Slewing Range: 13.70 m at 210 kg Maximum Lifting Height: 11.5 m, up to 16.40 m with optional equipment Dimensions (L x W x H): 2.98 m x 0.77 m x 1.88 m Dimensions including winch and jib: 3.20 m x 0.77 m x 2.00 m Total Weight: 2,850 kg Mast System: Cylinder and chain system Jib Angle: -5 to 83 degrees Slewing: 360 degrees Travel Speed: 2.2 km/h Engine: Yanmar 3-cylinder, 7.3 kW (diesel), 1,500 rpm Electric Drive: 230V Starter: Electric start via remote control Fuel / Tank Capacity: Diesel / 20 l Inclination Angle: 15 degrees Ground Pressure: 0.79 kg/cm² Included Special Options: Fly-jib 30° Adjustable Extension Section Folding outriggers Winch: 3,000 kg Would you like another demonstration of a Hoeflon mini crane? No problem, we will come to your preferred location and would be happy to present the Hoeflon mini crane to you.

Durumu: yeni, Donanım: her tahrikli, Hoeflon Mini Crane C6e – New Machine Powerful All-Rounder Fpsdpfx Aet Il Dboh Dsc Available from stock. Capacity: 3,000 kg Max. Slewing Radius: 13.70 m at 210 kg Max. Lifting Height: 11.5 m (up to 16.40 m with options) Dimensions (L x W x H): 2.98 m x 0.77 m x 1.88 m Dimensions incl. winch and jib: 3.20 m x 0.77 m x 2.00 m Total Weight: 2,850 kg Mast System: Cylinder and chain system Jib Angle: -5° to 83° Slewing: 360° Travel Speed: 2.2 km/h Engine/Battery: OX Power battery Inclination Angle: 15° Ground Pressure: 0.79 kg/cm² Included Special Options: Fly jib Adjustable extension section (30°) Foldable outriggers Winch: 3,000 kg

Durumu: yeni, toplam ağırlık: 41.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 12.360 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 1.800 mm, Üretim yılı: 2021, Donanım: ABS, 40', 2x 20', 1x 30', 1x 40' HC konteyner için değiştirilebilir yarı römork * Kaldırma aksı * Arka, pnömatik olarak 1360 mm uzatılabilir * Disk frenli SAF akslar * Jost destek ayakları * Wabco Treyler EBS-E, ABS * Haldex Colas hava sistemi * Takozlar ----Araç numarası 6945 -----Hatalar ve ara satış hakkı saklıdır Fodpfx Ajkc T Ngoh Dopc WhatsApp desteği mevcuttur! Araçla ilgili sorularınız için veya daha fazla bilgi almak için bize WhatsApp üzerinden kolayca ulaşabilirsiniz Whatsapp Whatsapp

Durumu: yeni, Üretim yılı: 2024, Hoeflon Mini Crane C10e – New Machine The Powerful All-Rounder Delivery time: on request Capacity: 4,000 kg Max. slewing range: 13.70 m x 500 kg – with options: 19.80 m x 209 kg Max. lift height: 16.30 m incl. options: 22.00 m Dimensions L x W x H: 3.93 m x 0.80 m x 1.97 m Dimensions incl. winch and jib: 4.15 m x 0.80 m x 2.07 m Total weight: 4,400 kg, incl. options 4,700 kg Jib arm weight: 205 kg Jib angle: 5–83 degrees Slewing: 360 degrees Remote-controlled drive system: 1st gear: 1.1 km/h, 2nd gear: 2.3 km/h, 3rd gear: 2.9 km/h Electric drive: 400 V Inclination angle: 20 degrees Fodpfxerbdh Eo Ah Depc Optional special equipment: Fly-Jib 30° adjustable extension Winch: 4,000 kg Custom paintwork

Durumu: yeni, Üretim yılı: 2023, Donanım: her tahrikli, Haulotte Compact 10DX – New Machine Delivery time: on request Color: Haulotte Standard (RAL1006) Delivery to your desired address is possible. Working height: 10.28 m Platform height: 8.28 m Maximum load capacity: 565 kg Platform length: 2.45 m Platform length with extension: 3.7 m Platform extension: 1.2 m Platform width: 1.45 m Transport height: 1.59 m Height when retracted: 2.44 m Width: 1.78 m Length: 3.17 m Wheelbase: 1.84 m Standard features: * Four-wheel drive, steerable front wheels * Free-wheel function on drive motors * Foam-filled all-terrain tires * One-sided platform extension 1.2 m * Removable control panel on the platform * 3° inclination sensor Fjdpemv Natjfx Ah Dopc * Automatic outrigger levelling * Horn * Hour meter * Batteries 12 V – 74 Ah * Hydraulic brakes * Manual emergency lowering * Lashing points for fall protection * Towing and lifting eyes * Side guards Additional options: * Non-marking tires * Power outlet on the work platform * Swing door * Hydraulic generator 3.5 kW * Biodegradable hydraulic oil * Cold climate kit * Telematics preparation* * Audible drive alarm * Drive warning signal * Rotating beacon * Work lights * Foldable guard rails* * Custom paint (RAL) *Only available ex works, cannot be retrofitted to stock machines. 24 months manufacturer’s warranty on labour and spare parts.