Alçak yükleyici

Faymonville MAX Trailer 3-Achs-Tele-Semi-RM-ALU-Ram.

Gooseneck:
- Gooseneck with rear chamfer approx. 750 mm x 10°
- 3 pairs of lashing rings (LC 5,000 daN)
- 30 mm thick hardwood flooring

Loading Area:
- Telescopic loading area with rear incline approx. 1,000 mm x 8°
- 1 pair of fixed built-in wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm
- Wheel recesses equipped with 15 x 15 mm square climbing strips and lower-section extensions
- 1 pair of fixed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm
- 3-part removable galvanized covers over wheel recesses (W 670 mm) – max. point load 5 t / pc.
- Recess in the ramp and extending into the load area to accommodate an excavator bucket arm approx. 2,900 x 750 x 210/290 mm
- 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN)
- 5 pairs of fold-out lashing rings (LC 5,000 daN)
- 2 pairs of fold-out lashing rings (LC 10,000 daN)
- 2 pairs of lashing rings in the excavator arm depression (LC 5,000 daN)
- Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN)

One-piece ALU ramps:
- One pair of single-piece ALU ramps approx. 2,500 x 600 mm
- Ramps with spring assist and manual lateral adjustment
- Maximum load per pair: 24,000 kg

Axles and Tyres:
- BPW axles and suspension, 2 rigid axles, 1 self-steering axle
- Technical axle load: 12,000 kg
- Electromagnetic reverse lock, activated via reverse gear and manually
- Air suspension with raise/lower valve
- Axle tools
- Tyres 235/75 R 17.5
- TPMS (Tire Pressure Monitoring System) in compliance with ECE R 141

Accessories included:
- One spare wheel with bracket in front of the bulkhead
- 2" kingpin
- One galvanized steel bulkhead ca. 400 mm high
- Yellow-red air couplings at the galvanized front coupling strip
- 4 chocks with bracket at the bulkhead
- Accommodation at the rear of the gooseneck for ALU approach ramps
Cjlhoiu Er Ascdw Hori
- Galvanized extensions, extendable approx. 230 mm per side
- Galvanized folding supports under the rear incline of the loading area
- Bracket for a rotating beacon at the rear of the trailer
- White reflector tape in accordance with EU requirements on sides, red on extension and rear
- On the gooseneck and rear panel, bracket for warning boards including socket, left and right
- On the gooseneck, plug-in ALU side walls and rear wall approx. 2,440 x 400 mm
- Removable rear galvanized stanchions (body length approx. 2,560 mm)
- 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container
- 3 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area
- One removable galvanized intermediate table with 1 pair WADER container pockets
- 20 x 20 mm square climbing strips every 200 mm along the outer frame of the loading area's rear incline
- Non-slip sand coating painted onto the checker plate on the gooseneck and loading area
- Four warning boards extendable by approx. 400 mm each, approx. 423 x 423 mm with position light
- Bracket for rotating beacon on warning boards
- 80 km/h speed stickers on the rear and both sides
- Load gauge for axle load determination including load chart
- HRM Metallization (High Resistance Metallisation) of the outer frame
- Complete steel structure shot-blasted, then defined visible surfaces metallically finished with ZINACOR 850 (Zinc 85% - Alu 15%) hot metalized

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.