Alçak yükleyici

Fliegl VTS 400

Durum: yeni, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: Produktpalette, boş ağırlık: 9.900 kg, azami yük ağırlığı: 14.100 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 aks, lastik boyutu: 235 / 75 r 17,5, Özel Taşıma Çözümü Fliegl aracınızı ihtiyaçlarınıza göre yapılandırın. Gösterilen araç bir örnektir. Üretim ve donanım, müşterinin talebine göre bireysel olarak gerçekleşir. Diğer Bilgiler Şasi Çelik kaynak konstrüksiyonu Güçlü bilyalı döner tabla ile döner şasi, entegre depolama kutusu dahil Döner tabla önü Katlanabilir arka destek 2 adet takoz ve tutucu Yan koruma alüminyum Arka kısımda tüm genişlik boyunca çamurluk 3.000 mm'ye kadar çekilebilir genişletmeler (arka eğim hariç) (Transport edilecek iş makineleri veya araçların iz genişliği, dış çerçeve genişliği 2.550 mm'yi geçmemelidir) Yük alanının ortasında ahşap kalaslar için saklama bölmesi 3000 mm genişletme için 70 mm ahşap kalas Alçak şasi için bağlama halkaları Önde tabana entegre 3 çift bağlama noktası, her biri 10 ton Dış çerçeveye üstten ve yandan gömülü 6 çift bağlantı mantarı, her biri 10 ton 1x boyun bölgesinde Kalanlar aralarda, mesafe 1200 mm'den fazla olmamak üzere dağıtılmıştır 1x arka eğimde Dış çerçevede gömülü 5 çift kazık yuvası, içeriden 70 x 40 mm (5 ton halka bağlama noktasına dönüştürülebilir, teslimata dahil değildir) Döner şasi römorku çekme tertibatı Test edilmiş 40 mm çekme halkasıyla çekme kolu Not! 40 mm çekme halkasıyla, kamyonun izin verilen toplam ağırlığı en fazla 18.000 kg olabilir, aksi halde 50 mm çekme halkası gereklidir. Akslar ve Süspansiyon SAF tambur frenli akslar Aks ve şasi lazer ölçümlü: lastik aşınma ve yakıt tüketimini azaltır Önde ve arkada bakım gerektirmeyen çelik-kauçuk burçlu ve mekanik aks yük dengeleyicili parabollu süspansiyon (salınım dengeleyici) Jant & Lastikler 235 / 75 R 17,5, üreticiye göre seçilir Çiftli düzen çelik jantlar, fabrika gümüşü Fren Sistemi Çift hatlı pnömatik fren sistemi Yaylı park freni Önde 2 adet karıştırılamayan bağlantı başlığı, motorlu araç ile bağlantı kabloları ABS ve ALB, önde ABS fişi ve bağlantı kablosu Dikkat: Römork, ancak çekici aracın ABS'nin düzgün çalışmasını sağladığı durumlarda çekilebilir! Elektrik 24 Volt, çok odacıklı lambalar, yanlarda sarı LED aydınlatma Önde 2 beyaz konum lambası Arkada 2 beyaz/kırmızı şerit lambası Önde karıştırılamayan 2 adet 7-pin fiş ve bağlantı kablolu 1 adet LED döner lamba ve tutucu, park lambası ile çalıştırılır (lamba sökülebilir) 2 çift uyarı levhası, çift LED aydınlatmalı ve 3.000 mm'ye kadar uzatılabilir Zemin Ön bölüm çelik zemin, daha sonra 70 mm yumuşak ahşap zemin, çamurluk bölgelerinde çelik/kaymaz sac kaplama Arka eğimde 70 mm yumuşak ahşap zemin Rampalar Çelik rampalar 2800 mm uzunluğunda, 750 mm genişliğinde, yanlara kaydırılabilir Üstü ahşap kaplamalı Yaylı kaldırma desteği Çalışma Notları 10.000 kg aks yükü için istisna izni gereklidir, sadece bölünemez yük mümkündür! Belirtilen toplam ağırlık teknik olarak mümkündür, fakat yükün tipine göre izin verilen aks/destek ve şasi yükleri aşılmadığı sürece toplam ağırlığa ulaşılamayabilir. Tescil Ülkesi/Plakalar: Ljdpsi Ri I Eefx An Tjrn Tescil ülkesi: Almanya 1 adet Dekra onayı ve raporu (EG - FGV §13'e göre) 24/7 Servis Hattı Çift satırlı plakalık için uygun Kontur işaretleme ECE R 048'e göre yansıtıcı şeritlerle: yanlarda beyaz, arkada kırmızı Boyama Şasi RAL 3002 karmen kırmızısı Pas oluşumuna karşı 10 yıl garanti Çekme kolu galvanizli veya siyah, üretici seçimine göre Rampalar ateşle galvanizli Dikkat: Arşiv resimleri!

Durum: yeni, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: Produktpalette, boş ağırlık: 14.300 kg, azami yük ağırlığı: 9.700 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 900 mm, toplam uzunluk: 12.000 mm, toplam genişlik: 2.550 mm, süspansiyon: hava, lastik boyutu: 235 / 75 r 17,5, lastik durumu: 100 yüzde, Özel Taşıma Çözümü Fliegl aracınızı ihtiyaçlarınıza göre yapılandırın. Gösterilen araç bir örnektir. Üretim ve donanım, müşterinin isteğine göre bireysel olarak gerçekleştirilmektedir. Daha fazla bilgi Şasi Çelik kaynak konstrüksiyonu Güçlü döner tabla, büyük bilyalı döner tabla Katlanabilir arka destek 2 takoz ve aparatı Alüminyum yan koruma Tüm genişlikte arka çamur siperliği 1. aks önünde çeyrek sac çamurluk Ekskavatör kolu çukuru, arka aksın hemen gerisinden başlayıp arka uca kadar uzanır, yaklaşık 1.800 mm uzunluğunda, yaklaşık 650 mm genişliğinde ve yaklaşık 150 mm derinliğinde, çukurun yan tarafında, uzunlamasına şasinin her iki yanında, önden yaklaşık 300 mm ve arka eğimden yaklaşık 200 mm önce, her biri 5 tonluk 2 çift tutma deliği. Tabana gömülü, kapaklı, 1 adet saklama kutusu, G=720 mm / U=520 mm / D=170 mm Yüksek yatakta kıvrımdan sonra yerleştirilen 1. çift tekerlek çukuru, giriş için eğimli, alt uzunluk yaklaşık 1.600 mm, yaklaşık 400 mm derinlik. Not! Ana taşıyıcı alanında şasi, tekerlek çukurundan 400 mm daha yüksektir. Tekerleklerin arasındaki yüksek yatakta yerleştirilen 2. çift tekerlek çukuru, giriş için eğimli, alt uzunluk yaklaşık 600 mm, yaklaşık 300 mm derinlik. Not! Ana taşıyıcı alanında şasi, tekerlek çukurundan 300 mm daha yüksektir. Tekerlek çukuru örtüleri, ana şaseden çekilebilir, ahşap kaplamalı. Ana taşıyıcıdan taşıyıcıya dışarıdan mesafe yaklaşık 1.280 mm'dir. Genişletmeler, tekerlek çukurlarının uzantılarında katlanabilir şekilde 3.000 mm'ye kadar çekilebilir (genişletme arka eğimde ve teker çukurlarının alt kısmında mümkün değildir). Taşıma tahtası deposu, yükleme yüzeyi ortasında veya teknik imkanlara göre yükleme yüzeyinin altında. 3.000 mm’ye kadar genişleme için 70 mm ahşap plakalar. Alçak yatak sabitleme halkaları Önde kıvrımda gömülü 1 çift sabitleme halkası, her biri 5 ton Üst ve yan dış şaside toplamda 8 çift sabitleme mantarı, her biri 10 ton 2 x önde kıvrımda 6 x alçak yatakta: ilk sabitleme noktası önden 250 mm, sonuncusu arkadan maksimum 250 mm uzakta, aralarındaki mesafe maksimum 1.100 mm Dış şaside gömülü 5 çift halka sabitleme noktası, her biri 5 ton (yan payandalar için uyarlanabilir) Çekici tertibatı, döner tabla römork için Test edilmiş 50 mm çeki gözlü, 8° eğimli çeki gögzlü çeki çatalı Akslar ve süspansiyon SAF kampana fren aksları Akslar/şasi lazerle ölçülmüş, lastik aşınması ve yakıt tüketimini azaltır Önde ve arkada ayrı ayrı kumanda edilebilen yükseltmeli ve alçaltmalı havalı süspansiyon Tekerlekler ve lastikler Üreticiye göre 235/75R17,5 Çift düzenli çelik jantlar, fabrika gümüşü Fren sistemi İkili hatlı pnömatik fren sistemi Yaylı park freni Araç verilerini gösteren Trailer Infocenter, dingil yükü (tartılı sistem değildir) ve kilometre sayacı Dingil yükü algılama, EBS-Canbus sinyali üzerinden, sürücü kabinindeki ekrandan görüntüleme için, çekici hazırlıklı olmalı, kurulum yapılmadı (tartılı sistem değildir) Araç denge sistemi Önde Duomatic bağlantı, çekiciye bağlantı kablosu ile EBS, Elektronik Fren Sistemi, önde EBS fişi ve bağlantı kablosu ile Ljdsi Ri I Nepfx An Torn Dikkat: Bu römork yalnızca ABS işlevselliği garanti edilen çekici araçlarla çekilebilir! Elektrik 24 Volt, dirençli LED çok odacıklı aydınlatma, yana sarı LED aydınlatma, plakalı LED aydınlatma Önde 2 adet beyaz LED konum lambası Arkada 2 adet beyaz/kırmızı yol tutucu LED lamba Arkada geri vites ile kumanda edilen ek LED çalışma farı Önde 1 x 15 pinli fiş ve bağlantı kablosu 1 adet LED döner uyarı lambası ve aparatı

Durum: yeni, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: Produktpalette, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı yüksekliği: 900 mm, toplam uzunluk: 11.940 mm, toplam genişlik: 2.550 mm, süspansiyon: hava, lastik boyutu: 235 / 75 r 17,5, lastik durumu: 100 yüzde, Further information Chassis Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear splash guard Semi-shell mudguards on 1st and 2nd axles with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess over the rear axles, running to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated 5 t each in the excavator arm recess at the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear incline 1 plastic toolbox, with insert shelf, w=620/h=360/d=440 mm, lockable with padlock (lock not included) 1 storage box recessed in the gooseneck in the floor with lid, W=720 mm/L=520 mm/D=170 mm Extendable width to 3,000 mm (not in the rear incline) (track width of machines or vehicles to be transported must not exceed outer frame width of 2,550 mm) Lrjdpfxji Ri Daj An Tsn Timber beams 70 mm for extension to 3,000 mm Storage compartment for timber beams under loading area Lashing rings lowbed (40 lashing points) 1 pair of lashing rings on gooseneck, each 5t 9 pairs of lashing studs, integrated in the top and side of outer frame, each 10t 2 x on gooseneck in front 7 x in the lowbed area 6 pairs of lashing holes in the outer frame of the lowbed area, 5 t each (for tie-down straps) 3 additional pairs of folding lashing rings, each 10 t 1 x inside next to main frame at start of lowbed 1 x on gooseneck (protrudes) 1 x recessed in the floor behind the last axle Trailer drawbar assembly Drawbar with tested 50 mm towing eye, towing eye inclined at 8°, D-value minimum 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 as selected by manufacturer Steel twin wheels, factory silver Brake system 2-line air brake system Spring-loaded parking brake 2 anti-mismatch coupling heads at front, with connection lines to truck ABS and ALB, with ABS plug at front, with connection cable Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at front 2 white/red marker lights at rear 2 x 7-pin anti-mismatch plugs at front, with connection cable 1 LED rotating beacon with holder, controlled via parking light (beacon detachable) 2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel/aluminium chequer plate covering followed by 70 mm softwood floor, with steel/aluminium chequer plate over wheel wells Rear incline with 70 mm softwood floor Access ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable with timber surfacing Hydraulic, powered via tractor PTO with flow restrictor, controlled laterally front left Hydraulic connection with SVK plug NW 10/3, including connecting hose Approval country / Plates Approval country: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective tape as per ECE R 048, side white and rear red Warning sign according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation, 15 years corrosion perforation warranty Drawbar galvanized or black, as per manufacturer’s choice Access ramps hot-dip galvanized Note: Images are for illustrative purposes (archive images)!

Durum: yeni, azami yük ağırlığı: 31.920 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 10.410 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, New Fliegl 4-axle low loader trailer with ramps, model VTS 400 Total weight: 24,000kg / 40,000kg Unladen weight: 8,080kg Payload: 15,920kg / 31,920kg Overall length: 11,940mm Loading length: approx. 10,410mm total, gooseneck approx. 2,490mm, loading platform including rear incline approx. 7,920mm Width: 2,550mm Loading height: 900mm Additional information Plus pre-shipping / handling from stock location 26639 Wiesmoor: €1,280.00 net Hire purchase offer: Term 48 months, down payment only VAT, residual value 40% Monthly rate EUR 759.00 Chassis, Low Loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Aluminum side underrun protection Full-width rear mudflap Half-shell mudguards for axles 1 and 2 with anti-splash mudflaps behind each axle, Anti-splash mudflaps before and after axles 3 and 4 Excavator arm recess over rear axles extending to rear, approx. 1,800mm long, approx. 650mm wide and approx. 150mm deep 2 pairs of lashing holes rated to 5t each, in the excavator arm recess on the side of the longitudinal frame approx. 300mm from the front and approx. 200mm before rear incline 1 lockable plastic toolbox, w=600 / h=425 / d=460mm Recessed storage box in the gooseneck with lid, w=720mm / l=520mm / d=170mm Extendable widenings to 3,000mm (not in the rear incline) (Note: track width of machines or vehicles to be transported must not exceed external frame width of 2,550mm) Storage compartment for timber planks under the low-bed area 70mm timber planks for widening to 3,000mm Low loader lashing points 1 pair of lashing recesses in the front longitudinal member within the gooseneck, each rated to 10t 4 pairs of lashing holes on the outer frame, rated to 5t each (for securing straps) 9 pairs of recessed lashing mushrooms (above and side of outer frame), each rated to 10t 2 x at the front on the gooseneck 7 x on the low-bed deck First lashing point 250mm from the front and last max. 250mm from the rear, distance between lashing points max. 1,100mm 3 additional pairs of folding lashing points, each rated to 10t 1 x on the gooseneck (protruding) 1 x at the start of the low-bed deck, recessed inside the longitudinal beams 1 x recessed in the floor behind the last axle Drawbar assembly, turntable trailer Drawbar with certified 50mm towing eye Drawbar height adjustment via spring Axles and Suspension Drum brake axles, manufacturer’s choice "Axle/chassis laser alignment" reduces tire wear and fuel consumption Air suspension with raise & lower valve + auto-reset function Wheels & tyres 235/75 R 17.5" manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS CAN bus signal, for display in the driver's cab (truck must be appropriately pre-equipped, not installed in this trailer; not a calibrated scale) Vehicle stability control system 2 fail-safe coupling heads at the front, with connecting lines to tractor unit, 12-24 Volt EBS, electronic braking system with EBS plug at the front, including connection cable Knorr make Note: This trailer may only be towed by vehicles that guarantee effective ABS operation! Electrical system 12-24 Volt, multi-chamber LED lights, side yellow LED lighting, LED number plate lighting, (Note: Certain tractor units may show fault codes even though functionality is correct) 2 white front position lights, LED Ljdpfx Anevv D Ixs Tjrn 2 red/white lane marker ligh

Durum: yeni, azami yük ağırlığı: 30.010 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 10.000 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, New vehicle: Fliegl 4-axle low loader trailer with wheel recesses and split ramps, type VTS 400 RM Lease-purchase offer: 48-month term, down payment only VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low loader First registration: New vehicle Gross weight: 24,000 kg / 40,000 kg Unladen weight: 9,990 kg Payload: 14,010 kg / 30,010 kg Overall length: 12,000 mm Load length: total approx. 10,000 mm, gooseneck approx. 2,850 mm, loading deck including rear bevel approx. 7,150 mm Width: 2,550 mm Loading height: 900 mm Further information: Chassis: Low loader trailer Steel welded construction Turntable with heavy-duty ball race Rear support foldable Wheel chocks with holder Aluminium side underrun protection Full-width rear mudflap Half-shell mudguards on 1st & 2nd axle with anti-spray flaps behind each axle, anti-spray flaps behind the 4th axle Excavator arm recess above the rear axles, extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes, each rated 5 t, in the excavator arm recess at approx. 300 mm from the front and approx. 200 mm before the rear bevel Spare wheel holder for 1 spare wheel, mounted vertically on the front center of the gooseneck. Spare wheel manufacturer as base tires, steel rim Storage box sunken into the floor of the gooseneck with cover, W=720 mm / L=520 mm / D=170 mm 1st pair of wheel recesses behind gooseneck, fitted in low-bed lane area, ramped entrance, bottom length approx. 1,600 mm, approx. 400 mm deep. Note: Main frame is 400 mm higher than wheel recess in this area. 2nd pair of wheel recesses between axles, fitted in low-bed lane area, ramped entrance, bottom length approx. 600 mm, approx. 300 mm deep. Note: Main frame is 300 mm higher than wheel recess in this area. Extendable width up to 3,000 mm (extension not available at the rear bevel or inside wheel recesses). (Track width of machines/vehicles to be transported must not exceed external frame width of 2,550 mm) Storage compartment for timbers under the low bed deck 70 mm timbers for extension to 3,000 mm Lashing points low loader: 1 pair of recessed ring lashing points at front of gooseneck, each 5 t 4 pairs of lashing holes in external frame, each 5 t (for hook-in ratchet straps) 8 pairs of welded-on lashing mushrooms, top and sides of the external frame, each 10 t 2x at front on gooseneck 6x in the low bed First lashing point 250 mm from the front, last max. 250 mm from rear; distance between lashing points not greater than 1,100 mm 5 pairs of stanchion pockets recessed in the external frame, internal 70 x 40 mm (can be converted to 5 t ring lashing points, not included) 1 pair of additional folding lashing points recessed in the floor, each 10 t 1x inside next to main frame at start of low bed 2 pairs of additional folding lashing points, each 10 t 1x on gooseneck (protrudes) 1x recessed in floor behind rearmost axle Drawbar coupling for turntable trailer: Drawbar with tested 50 mm coupling eye, coupling eye angled at 8° D-value min. 160 kN Axles + Suspension: BPW drum brake axles Laser-aligned axles/chassis; reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation at front (rocker compensation) Wheels and tires: 235/75 R 17.5" Manufacturer’s choice, with M+S marking Steel rims in twin-wheel configuration, factory silver Lredpfx Aotrizkon Ton Braking system: 2-line compressed air brake system Spring-loa

Durum: yeni, azami yük ağırlığı: 31.100 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 10.410 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.520 mm, Total weight: 24,000 kg / 40,000 kg Unladen weight: 8,900 kg Payload: 15,100 kg / 31,100 kg Lrjdperducpefx An Tjn Total length: 11,940 mm Loading length: 10,410 mm total, 2,490 mm gooseneck, 7,920 mm loading platform including rear bevel Width: 2,520 mm Loading height: 900 mm Further information plus pre-carriage / provision ex stock location 26639 Wiesmoor €1,280.00 / net Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports Wheel chocks with holder Aluminium side underrun protection Rear mud flap across entire width (not available with forklift holder) Half-shell mudguards 1st & 2nd axle with anti-spray flaps behind each axle, anti-spray flaps before and after 3rd and 4th axle Digger boom recess over rear axles extending to rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep 2 pairs of lashing holes, each 5 t, in the digger boom recess at the side of the main frame approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 lockable plastic toolbox, w=600 / h=425 / d=460 mm 1 storage box recessed into the floor of the gooseneck with lid, W=720 mm/ L=520 mm / D=170 mm Extendable widening to 3,000 mm (not on rear bevel) (The track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden boards under the lowbed surface 70 mm wooden boards for widening to 3,000 mm Low loader lashing points 1 pair of lashing cut-outs recessed in main longitudinal beam at the front on the gooseneck, each 10 t 4 pairs of lashing holes in the outer frame, each with 5 t (for tensioning strap hooks) 9 pairs of lashing mushrooms on top and side of the outer frame, each 10 t 2 x at the front on the gooseneck 7 x in the lowbed first lashing point 250 mm from the front and last max. 250 mm from the rear, distance between lashing points not more than 1,100 mm 3 additional pairs of folding lashing points, each 10 t 1 x on the gooseneck (protrudes) 1 x beginning of the lowbed recessed into longitudinal beams 1 x behind the last axle recessed in the floor Drawbar coupling turntable trailer Drawbar with certified 50 mm towing eye Drawbar height adjustment via spring Axles & Suspension Drum brake axles, manufacturer’s choice "Axles/chassis laser-aligned" – reduces tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation front and rear (rocker compensation) Wheels and tyres 235/75 R 17.5" as per manufacturer’s choice Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic brake system Spring-actuated parking brake 2 non-interchangeable coupling heads at front, with connection hoses to towing vehicle, 24 volt ABS and ALB, with ABS connector at front, with connecting cable Note: The trailer may only be towed by vehicles that ensure the effectiveness of ABS! Electrics 12-24 volt, multi-chamber LED rear lights, side yellow LED lights, number plate lighting in LED (Note: certain towing vehicles may show malfunction warnings despite functioning) 2 white front position lights in LED 2 white/red rear marker lights in LED 2 x 7-pin non-interchangeable plugs at front, with connecting cable 1 LED beacon with holder, switchable via parking light (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel/checker plate surface, then approx. 70 mm softwood floor, in w

Durum: yeni, azami yük ağırlığı: 30.310 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Total weight: 40,000 kg Payload: 30,310 kg Unladen weight: 9,690 kg Overall length: 12,000 mm Loading length: 10,000 mm Load bed: 7,150 mm including 850 mm drive-up slope Loading height: 900 mm Lredsnzlg Depfx An Tsn 1st pair of wheel recesses after drop in the load bed, length at bottom approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the load bed, length at bottom 600 mm, 300 mm deep Extensions to 3,000 mm, warning signs, beacon, Comprehensive lashing package 5 pairs of stake pockets in the outer frame Excavator boom recess 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with lifting and lowering valve, can be operated separately BPW drum brakes Tyres: 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps 2,800 mm x 750 mm with hydraulic operation Hydraulic lateral shifting Hire-purchase offer: 48-month term, residual value 40%, down payment only VAT on the rental instalments, monthly instalment EUR 970.00 net Vehicle available from 11/09/2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121, right next to the main entrance. Other 3-, 4- and 5-axle low loaders new and used available immediately.

Durum: yeni, azami yük ağırlığı: 31.920 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 10.410 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, New Fliegl 4-axle low loader trailer with ramps, model VTS 400 Gross vehicle weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Overall length: 11,940 mm Loading length: total approx. 10,410 mm, gooseneck approx. 2,490 mm, loading platform incl. rear bevel approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Further information Plus delivery / provision from stock location 26639 Wiesmoor: €1,280.00 net Chassis – Low Loader Trailer Steel welded construction Turntable with heavy-duty ball-race ring Folding rear supports 2 wheel chocks with holder Aluminium side underrun protection Full-width rear mud flap Half shell mudguards on 1st and 2nd axles with anti-spray flaps behind each axle Anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess over the rear axles extending to the rear, approx. 1,800 mm long, 650 mm wide, 150 mm deep 2 pairs of lashing points, each rated at 5 t, in the excavator arm recess on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear bevel 1 plastic toolbox, w = 600 mm / h = 425 mm / d = 460 mm, lockable Storage box recessed in the gooseneck floor with lid, W = 720 mm / L = 520 mm / D = 170 mm Extendable width to 3,000 mm (not in rear bevel area) (Track width of transported construction machines or vehicles must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks beneath the low loader deck 70 mm wooden planks for widening to 3,000 mm Lashing points for low loader 1 pair of lashing cut-outs recessed in the longitudinal beam at the front on the gooseneck, each rated at 10 t 4 pairs of lashing holes in the outer frame, each rated at 5 t (for ratchet strap attachment) 9 pairs of lashing mushrooms recessed on top and side of the outer frame, each rated at 10 t - 2 at the front on the gooseneck - 7 in the low-bed section First lashing point 250 mm from the front and last max. 250 mm from the rear, distance between lashing points not more than 1,100 mm 3 pairs of additional folding lashing eyes, each rated at 10 t - 1 on the gooseneck (protruding) - 1 at the beginning of the low-bed section recessed in the inner longitudinal beams - 1 behind the last axle recessed in the floor Towing gear for turntable trailer Drawbar with certified 50 mm towing eye Drawbar height adjustment via spring Axles & suspension Drum brake axles, manufacturer’s choice Lrjdpfx Asxrx Nlon Ton "Axle/chassis laser alignment" reduces tyre wear and fuel consumption Air suspension with lift & lower valve + auto-reset function Wheels and tyres 235 / 75 R 17.5” – manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake Axle load detection via EBS-CAN bus signal for cockpit display (truck must be appropriately equipped, not truck-installed, not a calibrated scale) Vehicle stability control system 2 non-interchangeable coupling heads at the front with connecting lines to the towing vehicle 12-24 volt EBS (Electronic Braking System), plug at the front, with connecting cable (Knorr brand) Note: The trailer may only be towed by vehicles which ensure full ABS functionality! Electrics 12-24 volt, multi-chamber LED lights, side LED marker lights, LED number plate light (Note: On certain towing vehicles, incorrect diagnostics may occur, despite functional lighting) 2 white LED position lights at the front 2 white/red LED lane departure lights at the rear 2 x 7-pin non-interchangeab

Durum: ikinci el, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: WFDFLT44001000966, boş ağırlık: 9.400 kg, azami yük ağırlığı: 30.600 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 10/2010, yükleme alanı uzunluğu: 7.145 mm, yükleme alanı genişliği: 2.750 mm, yükleme alanı yüksekliği: 900 mm, toplam uzunluk: 12.120 mm, toplam genişlik: 27.500 mm, toplam yükseklik: 900 mm, süspansiyon: çelik, lastik boyutu: 235/75 R17,5", renk: kırmızı, The images are archive photos! Permissible / technical total weight: 24,000 / 40,000 kg Permissible / technical payload approx.: 14,600 / 30,600 kg Permissible / technical axle load: 24,000 / 40,000 kg Unladen weight (basic version) approx.: 9,400 kg +/- manufacturing tolerance Overall length approx.: 12,120 mm Maximum overall width: 2,750 mm Gooseneck length approx.: 2,850 mm Low bed platform length in the drive-aisle area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Lodjyxq A Hopfx An Tern Loading height in the low bed, laden, approx.: 900 mm Drawbar height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis – Low-loader trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection made of aluminium 1 plastic toolbox Extendable side extensions to 3,250 mm (not on the rear bevel) (Track width of the construction machinery or vehicles to be transported must not exceed external frame width of 2,750 mm) Storage compartment for timber planks at the center of the loading area 70 mm timber planks for widening to 3,000 mm 2 pairs of stake pockets in the low bed, recessed in the longitudinal beams of the floor Lashing rings low-loader: 2 pairs of lashing rings on the gooseneck, each 5t 1 pair of lashing rings in the rear bevel 4 lashing rings recessed centrally in the floor 2 pairs of keyhole profiles in the drive aisle for inserting longitudinal guide rails and for load securing 6 pairs of lashing mushrooms embedded in the low bed external frame, each 10t 5 pairs of stake pockets embedded in the low bed external frame 4 additional pairs of 10t lashing rings: 1x on the gooseneck 3x recessed in the low bed floor Drawbar and towing equipment: Turntable-type trailer drawbar with certified 50 mm towing eye Axles + Suspension: Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation front and rear (rocker balancing) Wheels and tyres: 235 / 75 R 17.5" Steel twin wheels, factory silver Brake system: 2-line compressed air braking system Spring-actuated parking brake 2 unmistakable coupling heads at front with connecting lines to towing vehicle ABS and ALB, with ABS plug at the front, with connection cable Note: This trailer may only be towed by vehicles that ensure ABS functionality! Floor: Front gooseneck with steel / chequer plate covering then 70 mm softwood flooring, steel / chequer plate in the wheel arch area Rear bevel with 70 mm softwood flooring Loading ramps: Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, wood-covered Hydraulically operated via tractor PTO Operational notes: An exemption permit is required for 10,000 kg axle load, only indivisible loads permitted!!! Note! Excessive length and width require a permanent special permit. When applying for an exemption in regulated heavy transport, axle load monitoring is mandatory for air-suspended vehicles!!! This applies to all deviations from § 34 German Road Traffic Licensing Regulations (StVZO) (axle and permissible total weight exceedance) requiring a § 70 exception permit. The specified total weight is technically feasible; however, depending on the cargo, the total weight may not be reached while observing permissible axle/support/king pin loads. (Poor driving and tracking characteristics may occur with improper load distribution) The images are archive photos!

Durum: ikinci el, azami yük ağırlığı: 30.500 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 06/2015, yükleme alanı uzunluğu: 10.170 mm, yükleme alanı genişliği: 2.500 mm, toplam genişlik: 2.520 mm, toplam yükseklik: 3.600 mm, Donanım: ABS, Hot-dip galvanized, low-bed length approx. 6520 mm, extendable to 3000 mm, loading height: approx. 910 mm, rear incline: 850 mm, high-bed 2800 mm, 50 mm towing eye, excavator arm recess, hydraulically adjustable loading ramps (LxW) mm, 9 lashing rings per side, 12 lashing eyes per side, 2 foldable rear supports, Duo-Matic coupling head, rotating beacon, extendable warning boards, ABS, EBS, SAF axle(s), drum brake system, leaf suspension. Vehicle may feature advertising decals and/or lettering. SI86936 Our offer generally does not include a new technical inspection (TÜV). If a new TÜV inspection is required, we will be happy to arrange a quote from our partner workshops! The vehicle may be fitted with advertising decals and/or signage. Our general terms and conditions of delivery and payment apply. We are happy to provide you with a financing or leasing offer for this item. Please contact us! Ledpfsy Trwzex An Tsrn