Kullanılmış Fliegl Push-Off Arabası satın al (300)

Durumu: yeni, makine/araç numarası: 55d3c5c03e032385649769b1b, boş ağırlık: 9.900 kg, azami yük ağırlığı: 14.100 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 aks, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Low Loader Trailer Steel welded construction Turntable with heavy-duty slewing ring, integrated storage box included. Turntable drawbar Foldable rear support 2 wheel chocks with holders Aluminium side underrun protection Full-width rear mudflap Extendable widening to 3,000 mm (not at rear chamfer) (Note: The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Central wooden plank storage compartment 70 mm wooden planks for widening to 3,000 mm Low loader lashing rings 3 pairs of lashing points rated 10 tonnes each, integrated at the front 6 pairs of lashing mushrooms, recessed in the upper and side outer frame, each rated at 10 tonnes 1 x in the neck area The remaining pairs are spaced at intervals no greater than 1,200 mm 1 x at the rear chamfer 5 pairs of stake pockets recessed in the outer frame, internal dimensions 70 x 40 mm (convertible to 5 t ring lashing eyes, not included) Turntable trailer drawbar system Drawbar with certified 40 mm towing eye Note! With 40 mm towing eye, the permissible total weight of the truck must not exceed 18,000 kg; otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Laser-measured axles/chassis for reduced tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation at front and rear (rocker compensation) Wheels and Tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims, twin configuration, factory silver Braking System 2-line pneumatic brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at front, with connecting lines to the tractor unit ABS and ALB, with ABS connector at front and connection cable Note: The trailer may only be towed by vehicles capable of ensuring effective ABS operation! Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white position lights at front 2 white/red lane marker lights at rear 2 x 7-pin non-interchangeable connectors at front, with connecting cable 1 LED beacon with bracket, operated via parking light (removable beacon) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Steel floor at front Followed by 70 mm softwood floor, steel/chequer plate in wheel arch area Rear chamfer with 70 mm softwood floor Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber-decked With spring-assisted support Operating Instructions An exemption permit is required for a 10,000 kg axle load, only indivisible loads permitted! The stated total weight is technically feasible; depending on the load, the total weight may not be achieved while adhering to the permitted axle, support, and kingpin loads. (Poor handling and tracking may result from incorrect load distribution) Registration/Country Signs Country of registration: Germany 1 with Dekra inspection and report (according to §13 EC - FGV) 24/7 Service Hotline Prepared for two-line licence plate holder Fsdpfxsi Ri I Ej Adgepd Contour markings with reflective strips to ECE R 048, white on sides and red at rear Paintwork Frame RAL 3002 Carmine Red 10-year anti-perforation warranty Drawbar, galvanised or black, as per manufacturer specification Access ramps hot-dip galvanised Note: Archive photos!

Durumu: yeni, makine/araç numarası: 8df1ead53cc82aeb51e50a37d, boş ağırlık: 4 kg, azami yük ağırlığı: 13.880 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Turntable Skip Loader Fine-grain steel welded construction Container locking system: - 2 pairs of locking hooks recessed into the floor - Pneumatic operation The container locking system is designed as an internal 2-point mechanism; locking of skip containers with internal bars is not possible (designed for the transport of roll-off containers with subframes according to DIN 30722). Note! At the start of the roller trough at the front, the container must be pushed on completely flat! Longitudinal guide rails, laterally adjustable and removable, rails approx. 115 mm high Turntable with heavy-duty ball bearing slewing ring 8 pairs of lashing mushrooms recessed into the upper and side parts of the outer frame, each rated at 5 t 7 pairs of stake pockets recessed into the outer frame, internal dimensions 70 x 40 mm (convertible to 5 t lashing rings, not included) 2 wheel chocks with holder Aluminium side underrun protection Steel rear underrun protection Quarter section mudguards according to EC standards With anti-spray mudflaps to EC Directive Drawbar arrangement for turntable trailers Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and Tires 235 / 75 R 17.5 Manufacturer’s choice Steel wheels in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 interchangeable coupling heads at front, with connecting lines to towing vehicle, ABS and ALB, with ABS socket at front, with connection cable Attention: The trailer may only be towed by tractors that ensure proper ABS function! Electrics 24 Volt, multi-chamber tail lights, yellow LED side marker lighting 2 white position lights at front 2 white/red lane marker lights at rear 2 x 7-pin interchangeable plugs at front, with connecting cable Floor Steel floor Fpodpoi Ri Nujfx Adged Container roller trough at front, recessed in floor, for roll-off containers 5,000 – 7,000 mm length Note: Minor floor deformation due to welding distortion possible! Loading ramps Lockable storage space for loading ramps beneath bed Operating instructions For 10,000 kg axle loads, a special permit is required. The permit must be applied for separately in each federal state; there is no guarantee from the legislator for 20 t permissible total weight. Customer’s risk. The specified total weight is technically possible; depending on the type of load, the permissible total weight may not be achievable while adhering to axle/support and kingpin loads (impaired driving and tracking possible from poor load distribution). Country of registration / Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC-FGV) 24/7 Service Hotline Prepared for one-line number plate holder Contour marking with reflective tape to ECE R 048, white lateral and red rear Warning panel according to ECE-70 Paintwork Frame DB 7350 Nova Grey 15-year warranty against rust-through Note: Floor deformation from hot-dip galvanization possible! Drawbar KTL black Important: Archive photos!

Durumu: yeni, makine/araç numarası: 6d88bda3a1ee2464a81b34f36, boş ağırlık: 4 kg, azami yük ağırlığı: 13 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Low-bed Trailer Steel welded construction, with slight central pre-camber, turntable with heavy-duty slewing ring, wheel chocks with holder, quarter-circle mudguards in front of and behind each axle. Lashing Eyes for Low-Bed Over front axle: 2 pairs of ring lashing eyes at 5t each, front at the gooseneck Low-bed: 4 pairs of lashing eyes, side-mounted in the low-bed at 6t each 5 pairs of lashing eyes at 5t between the longitudinal beams Drawbar / Turntable Trailer Coupling Drawbar with certified 40 mm towing eye, mechanically length-adjustable and lockable in 6 x 100 mm steps (Drawbar length 1,700 - 2,300 mm) Axles & Suspension BPW drum brake axles with 10t axle load each, automatic slack adjusters. Axle endurance braking test rated up to 105 km/h, rear axle manually removable. To remove: release air locking and lower the rear to the ground. Then disconnect the hoses at the rear module, insert the transport bar into one of the rear bushings, and, by gently pressing down and simultaneously pulling back, uncouple the rear (parking brake released). After loading or unloading, move the rear module into place and connect up to the marking. Then raise to driving height and reconnect hoses. Confirm bolt locking (visual check to ensure bolt locks) and test rear functionality. Air suspension with raise/lower valve Wheels and Tyres 235 / 75 R 17.5, from leading brands, steel rims in twin arrangement, factory silver finish Braking System 2-line air brake system, spring-loaded parking brake, 2 fail-safe coupling heads front, with connecting lines to tractor unit, EBS (Electronic Braking System) with EBS plug front, incl. connection cable. Attention: This trailer may only be towed by tractor vehicles capable of guaranteeing effective ABS operation! Electrics 24-volt system, multi-chamber lights, yellow side LED lighting, 2 white position lights front, 2 white/red lane marker lamps rear, rotating beacon with holder, operated via parking light circuit (beacon removable), 2 pairs of warning plates, double LED illuminated, extendable up to 3,300 mm, removable with plug, 2 x 7-pin fail-safe plugs front with connection cable, 1 x 7-pin agricultural plug, voltage transformer 12/24 volts (for electrical system only, not ABS/EBS) Floor Steel/chequer plate floor on gooseneck, between longitudinal and cross members with perforated plate covering. Axle covers not drivable, extension to 3,000 or 3,300 mm possible. Fpsdei Ri N Aopfx Adged Operating Notes Note! For 10,000 kg axle load, special approval is required. Approval must be requested separately in each German federal state; a commitment for 20t gross weight is not guaranteed by law. Customer risk. Special approval required if overall towing length exceeds 18,750 mm. Observe country-specific registration regulations. The specified gross vehicle weight is technically feasible; depending on the load, gross weight may not be achievable while adhering to permissible axle, support, and fifth-wheel loads. Observe BO-circle regulations!!! Registration / Plates Registration country: Germany, with Dekra inspection and report (according to §13 EC - FGV), prepared for single-line number plate holder, warning plate according to ECE-70, contour marking with reflective tape according to ECE R 048 Paintwork Front frame hot-dip galvanized with passivation, rear frame RAL9006 silver, drawbar KTL black Note: Archive images!

Durumu: kullanılmış, makine/araç numarası: 816b3dfbfa1c7d49b7d052bd6, boş ağırlık: 2.500 kg, azami yük ağırlığı: 8.000 kg, toplam ağırlık: 10.500 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2022, lastik boyutu: 235/75 r17,5, Üretim yılı: 2022, Further Information Chassis Central Axle Trailer Low Bed Fine-grain steel welded construction, gearbox support leg at the front, telescopic rear support, wheel chocks with holders, steel sheet mudguards over both wheels Central Axle Trailer Coupling Drawbar with certified 40 mm towing eye, height-adjustable via spindle (max. adjustment range 250 mm) Axles & Suspension Euro axles (as per our selection) with tapered roller bearings and S-cam brakes, laser-measured axles/chassis to reduce tire wear and fuel consumption, parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalisation (rocker equalizer) Brake System 2-line compressed air brake system, spring-loaded parking brake, two non-interchangeable coupling heads at the front with connection lines to the towing vehicle, ABS and ALB, ABS connector at the front, with connecting cable Note: The trailer may only be towed by vehicles which guarantee the effectiveness of the ABS! Electrics 24 volts, multi-chamber lights, side-mounted yellow LED lighting, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 1 x 15-pin plug at the front with connecting cable Deck TTS Low-profile steel tub, deck floor with steel/chequer plate covering, steel sides solidly welded to the floor, deck length 5,500 mm, front and side walls with load-lock profile for securing straps (8 front, 16 per side) Note: Slight floor corrugation may occur due to welding distortion! Pair of lashing rings, 1 x front in the corners of the steel tub and 1 x at the rear in the floor, each rated at 5 t. Additional pairs of lashing rings in the floor, each rated at 5 t. Ramps Steel ramps, 2 x 3,000 mm long, 510 mm wide, laterally adjustable, with handgrip, timber overlay, gas pressure springs for single-person operation Fpsdpfjqmc Raox Adgjd Operating Instructions The specified gross weight is technically achievable; depending on load type, the gross weight may not be attainable while observing the permissible axle, support and fifth wheel loads. (Poor driving and tracking behaviour possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany, with Dekra inspection and test report (in accordance with §13 EC-FGV), prepared for single-line licence plate holder, contour markings with reflective tape in accordance with ECE R 048, white on the sides and red at the rear.

Durumu: yeni, makine/araç numarası: f8fb99947a1c19bc4d63549ff, boş ağırlık: 6 kg, azami yük ağırlığı: 17 kg, toplam ağırlık: 24 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing race Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear spray flaps Half-shell fenders on the 1st axle with anti-spray mudflaps; anti-spray mudflaps behind 2nd and 3rd axles 1 plastic tool box, with shelf, w=620/h=360/d=440 mm, lockable with padlock (padlock not included) Extendable widening to 3,000 mm (not at the rear chamfer) (the track width of machines or vehicles to be transported must not exceed 2,550 mm outer frame width) Central storage compartment for wooden beams on the loading area 70 mm wooden beams for widening to 3,000 mm Lashing points on low loader 1 pair of recessed ring lashing eyes at the front on the gooseneck, each rated 5t 7 pairs of mushroom lashing points, recessed at top and side in outer frame, each rated 10t 1x at the front on the gooseneck 6x in the drop deck First lashing point 250 mm from front, last max. 250 mm from rear, distance between lashing eyes not greater than 1,100 mm 5 pairs of stake pockets recessed in side frame, internal dimension 70 x 40 mm (convertible for 5t ring lashing eyes, not included) 2 pairs of additional fold-down lashing eyes, each rated 10t 1x on the gooseneck (projecting) 1x recessed in the floor behind the last axle Trailer turntable drawgear Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Axle/chassis laser alignment to reduce tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation (equalising rocker) Wheels and Tyres 235 / 75 R 17.5 Manufacturer's choice with M&S marking Steel wheels in twin arrangement, factory silver Brake System 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at front, with connection lines to the towing vehicle ABS and ALB, with ABS connector at front, with connection cable Brand: Wabco or Knorr Note: This trailer may only be towed by vehicles which ensure the proper functioning of the ABS! Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white front position lights 2 white/red rear outline marker lights 2 x 7-pin non-interchangeable plugs at front, with connection cable 1 LED rotating beacon with holder, switched via parking lights (removable beacon) 2 pairs of warning panels, double LED illuminated and extendable to 3,000mm Floor Gooseneck at front with steel/chequer plate covering Storage box recessed on the transition slope to gooseneck After that, 70 mm softwood floor, steel/chequer plate covering in wheel arch area Rear slope with 70 mm softwood floor Low-bed platform including rear slope 6,500 mm Fpedpfx Aoi Riwfedgod Loading ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Additional ramp safety support, foldable underneath (prevents lateral slipping of the ramps, not in conjunction with hydraulic side ramp shift) Wooden inlay on ramps Spring lifting assistance Operating instructions At 10,000 kg axle load, an exemption permit is required, only indivisible loads possible!!! The stated total weight is technically possible; depending on the load, the gross weight may not be achievable while adhering to permissible axle, support, and kingpin loads. (Poor driving and trailing behaviour may result from incorrect load distribution) Country of registration/Plates Country of registration: Germany Approval according t

Durumu: yeni, makine/araç numarası: f80f2330e1318ef03bc20755e, boş ağırlık: 3.200 kg, azami yük ağırlığı: 35.800 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, Further information Fine-grained steel welded construction in lightweight design, fifth-wheel plate with replaceable 2" kingpin, only 2 longitudinal members as double-T-beams for subsequent mounting of a headboard rack at the front in the new/current design, outer frame slightly angled with load-lock profile for lashing strap attachment. Note! In order to attach straps in conjunction with drop sides, the sides must be opened! 24 t, 2-speed landing gear with single-sided operation, straight base, without slide compensation, wheel chocks with holders, foldable aluminium side underrun protection, extendable galvanized steel rear underrun protection, half-shell mudguards - loose, not installed!, with anti-spray flaps behind each axle, 1 plastic water tank, capacity approx. 30 l, installed on the left (direction of travel). BPW disc brake axles with 430 mm disc diameter, axles/chassis laser aligned to reduce tyre wear and fuel consumption, air suspension, first axle with automatic lift axle, additionally manually lowerable, operable via push button on the vehicle. 2-line air brake system, with 1 standard central air reservoir, spring-loaded parking brake, 2 interlock-safe coupling heads at the front, without connecting line, EBS (Electronic Braking System) with EBS socket at the front, without connection cable, EBS 2S/2M, test connection for brake cylinder pressure leading outside on the EBS module. Attention: The trailer may only be towed by towing vehicles which ensure the effectiveness of the ABS! With lifting and lowering valve, control unit + brakes integrated in the frame as with tipper semi-trailers, mounted in front of the axles. Brake lining wear indicator on disc brakes via ABS/EBS lamp on the truck. 385/65 R22.5 Continental make, steel rims, factory silver. Fpsdpfji Riwqex Adged 24-volt multi-chamber lights, side-mounted yellow LED lighting as on tipper semi-trailers, 3,000 mm width must be observed, 2 front white position lights in LED, loose, 2 white/red lane marker lights at the rear, 2 x 7-pin interlock-safe sockets at the front, without connecting cable. Germany, approval to EC 2007/46 for complete vehicle, 24/7 service hotline, prepared for double one-line license plate holder: 1 x plastic and 1 x stainless steel interchangeable holder. Warning panel according to ECE-70, aluminium, loose, EBS, safe parking, without contour marking / reflective tape according to ECE R 048. Frame: DB 7350 Nova Grey, Landing legs: black coated. Immediately available!

Durumu: yeni, makine/araç numarası: 81b04fd2e28f354df79a4c3b3, boş ağırlık: 3 kg, azami yük ağırlığı: 14 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235/75 r17,5``, Further information Chassis Swap Central Axle Trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Locking folding adapter + height adjustment for parking height 1,000 - 1,120 mm, folding centre supports and re-mountable guide rollers upwards, 4 container locks with sturdy outriggers on 20-foot base for swap bodies 7.15 / 7.45 and 7.82 1 pair of gearbox support feet at the front, with straight lower section and single-side operation on FR right 2 wheel chocks with holders Side underrun protection aluminium Rear underrun protection steel Half-shell mudguards Drawbar arrangement for central axle trailer Drawbar with certified 50 mm towing eye, freight forwarding version (not suitable for trucks with tail lift, or subject to further inspection in case of order) Undermount drawbar, free drawbar length approx. 2200 mm Axles & Suspension SAF drum brake axles Axle/chassis laser alignment, reduces tyre wear and fuel consumption Air suspension Brake system 2-line compressed air brake system with colour-coded piping for easy servicing. Spring-loaded parking brake 2 misconnection-proof coupling heads at the front, with connection lines to the truck, connector at FR-right EBS, Electronic Brake System with EBS plug at front, with connection cable, connector at FR-right Note: The trailer must only be towed by vehicles which ensure ABS functionality! With raise/lower valve, with holding function in both lower and raise position Vehicle – Driving Stability System Wheels and tyres 235/75 R17.5'' tyres, manufacturer at discretion Steel twin wheels, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red outline marker lights at the rear 1 x 15-pin plug at the front, with connection cable, connector at FR-right 2 additional LED work lights at rear, switched via reversing light Fjdsi Riy Nopfx Adgopd 1 LED work light front centre between the carriers, rear-facing, switched via reversing light Operating notes The stated total weight is technically feasible, depending on the load, the total weight may not be achievable within the permissible axle, support and kingpin loads. (Incorrect load distribution can result in poor driving and tracking behaviour) Registration country / Plates Germany With Dekra approval and inspection report (in accordance with §13 EC - FGV) 24/7 Service hotline Prepared for single-line license plate holder Warning plate in accordance with ECE - 70 Contour marking with reflective strips to ECE R 048, white on sides and red at rear Paint Frame in DB 7350 Novagrau, 10-year warranty against rust penetration Note: Archive images!

Durumu: yeni, makine/araç numarası: e7fbe178b85a202cade7e95af, boş ağırlık: 5 kg, azami yük ağırlığı: 22 kg, toplam ağırlık: 29 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis: Semitrailer for Forwarding Operators Fine-grain structural steel welded construction, fifth wheel plate with replaceable 2" kingpin, with two kingpin positions. Outer frame slightly inclined with Load-Lock profile for lashing strap hooks. Note! To hook lashing straps in combination with side walls, the side walls must be opened! 2 pairs of lashing eyes recessed in the gooseneck outer frame, each rated at 5 tonnes. 8 pairs of lashing eyes recessed in the outer frame at the lowbed area, each rated at 5 tonnes. 24-ton 2-speed landing gear, single-sided operation, with straight base, without compensating mechanism. 2 wheel chocks with holder. Aluminum side underrun protection. Steel rear underrun protection. Quarter-shell mudguards in front of and behind axle assembly. 2 stainless steel toolboxes, width=600/height=400/depth=500 mm, with polished, lockable door. 2 pairs of stake pockets recessed in the gooseneck outer frame, inner dimension 70 x 40 mm. 6 pairs of stake pockets recessed in the outer frame at the lowbed area, inner dimension 70 x 40 mm. Internal width between stakes: 2420 mm! 3 lashing/stake rails in the lowbed, transversely embedded in the floor, over the entire width to the outer frame (usable internal width between outer removable stakes approx. 2170 mm), approx. 100 mm high; with 20 mm round steel bars, top and bottom, spacing between bars approx. 60 mm. Bottom finished with angle sheet, half open downward. Suitable for lashing and inserting stakes 80 x 80 mm. Removable stakes, width=80/depth=50/length=1200 mm, hot-dip galvanized. Removable stakes, width=80/depth=80/length=1200 mm, hot-dip galvanized. Note: Stake pockets/removable stakes are not intended for the sole securing of long materials, pipes, etc. without additional lashing. Mechanical rear extension with hand crank, extendable by approx. 1,500 mm, lockable every 500 mm. Comes with support beam, load capacity over the entire width: 2,000 kg at 500 mm, 1,000 kg at 1,000 mm, and 500 kg at 1,500 mm. Includes retractable rear underrun protection with lighting. 2 pairs of removable stakes, width=80/depth=80/length=1200 mm, hot-dip galvanized. Open storage compartment for removable stakes, at the front wall or under the loading area (for 10 removable stakes 80 x 50 x 1200 mm and 4 removable stakes 80 x 80 x 1200 mm). Axles + Suspension SAF drum brake axles. Axle/chassis laser alignment - reduces tire wear and fuel consumption. Last axle is self-steering with automatic reverse lock via reverse light, and additional lock function on the vehicle via hand knob. Air suspension with raise & lower valve. Wheels and Tires 235 / 75 R 17.5 Fpodpoi Ri Hvefx Adgod Manufacturer's choice. Steel twin wheels, factory silver. Braking System 2-line compressed air brake system. Spring-loaded parking brake. 2 foolproof coupling heads at the front, without connecting line. EBS, electronic braking system with EBS socket at the front, without connecting cable. Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS CAN bus signal for display in the truck cab. The truck must be correspondingly equipped; no truck installation or calibrated weighing system included. Electrics 24 Volt, multi-chamber tail lights, yellow LED side marker lights. 2 white position lights at the front. 2 white/red track marker lights at the rear. 2 x 7-pin sockets at the front, without connecting cable. 2 additional LED work lights at the rea

Durumu: yeni, makine/araç numarası: 057736dac221bda3fc469966a, boş ağırlık: 3 kg, azami yük ağırlığı: 8 kg, toplam ağırlık: 11 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Center-Axle Trailer Fine-grain steel welded construction Outer frame slightly angled with Load-Lock profile for lashing strap attachment Note! To hook in the straps in combination with side walls, the side walls must be opened! Fpsdpsi Ri H Dofx Adgsd Gear support leg at the front Foldable rear support 2 wheel chocks with holders Underride protection, steel, galvanized Quarter-shell mudguards 1 plastic toolbox with insert shelf, width=620mm / height=360mm / depth=440mm, lockable with a padlock (padlock not included) 1 compartment for stake pockets open, below the loading area 4 pairs of stake pockets recessed in the outer frame, 83 x 83 mm internal dimensions 4 stake pockets centrally recessed in the floor, with reinforcements to the main frame, 83 x 83 mm internal dimensions 6 pairs of plug-in stakes B=80mm / D=80mm / L=2000mm, hot-dip galvanized Note: Stake pockets / plug-in stakes are not designed for securing long materials, pipes, etc. by themselves without additional lashing Hitch System Tandem Trailer Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 4 x 500 mm from 1800 - 3800 mm, drawbar length preset to 1800 mm, (note! Observe load distribution and support load) Axles & Suspension GFA axles with tapered roller bearings and S-cam brakes Axles/chassis laser-measured to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and Tyres 235 / 75 R 17.5 manufacturer's choice Steel rims, factory silver Brake System 2-line air brake system Spring-loaded parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front and connection cable Caution: The trailer may only be towed by vehicles that ensure the ABS is effective! Electrics 24 Volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red side marker lamps at the rear 2 x 7-pin, non-interchangeable plugs at the front, with connection cable Floor Approximately 30 mm thick phenolic resin-coated plywood, designed for high point loads Note: Floor warping due to weather influences possible! Platform length approx. 6,200 mm Operating Notes The specified gross weight is technically feasible; depending on the cargo, the gross weight may not be attainable while complying with permissible axle, coupling, and kingpin loads. Approval / Plates Country of approval: Germany with Dekra certification and expert opinion 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Nova Grey Attention: Archive Pictures!

Durumu: yeni, makine/araç numarası: f79a9f15e7131d57a512793ab, boş ağırlık: 8.900 kg, azami yük ağırlığı: 15.100 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 aks, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports 2 wheel chocks with holders Side underrun protection in aluminium Rear spray flaps over the entire width Quarter shell mudguard in front of the 1st axle Extendable side extensions to 3,000 mm (not in rear chamfer area) (The track width of the construction machinery or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for timber planks in the middle of the loading platform 70 mm timber planks for extension to 3,000 mm Lashing eyes low-loader 1 pair of lashing eyes on the gooseneck, each with 5 t capacity 9 pairs of lashing mushrooms recessed in top and side of outer frame, each with 10 t capacity 2 x on the gooseneck front 7 x in the low bed 6 pairs of lashing holes in the outer frame of the low bed, each with 5 t capacity (for attaching tie-down straps) Coupling Device for Turntable Trailer Drawbar with certified 50 mm towing eye Axles/Suspension SAF drum brake axles Laser-aligned axles/chassis - reduces tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical inclusion Axle load compensation front and rear (rocker balance) Wheels and Tyres 235 / 75 R 17.5 Manufacturer’s choice Steel twin wheels, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 volt, multi-chamber lamps, yellow LED side lights 2 white position lights at the front 2 white/red lane marker lights at the rear 1 LED beacon with bracket, switched via parking lights (removable lamp) 2 pairs of double warning boards, LED illuminated, extendable to 3,000 mm 2 x 7-pin fail-safe plugs at the front, with connection cable Floor Gooseneck front with steel/checker plate then with 70 mm softwood floor, in the wheel arch area with steel/checker plate Rear ramp with 70 mm softwood floor Loading Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable timber-covered Hydraulically operated via tractor power take-off with throttle, control on the left side at the front Hydraulic connection with SVK plug NW 10/3, incl. hose Operating Instructions For an axle load of 10,000 kg, a special permit is required, only indivisible loads allowed!!! The specified total weight is technically possible, but depending on the cargo, the total weight may not be achieved within the permissible axle/support/saddle loads. (Poor driving and trailing behaviour possible due to incorrect load distribution) Fedpfx Adei Ri Izegepd Registration Country / Plates Registration country: Germany with Dekra acceptance and report (according to §13 EC - FGV) 24/7 service hotline included prepared for double-line license plate holder Contour marking with reflective tape pursuant to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau 10 year warranty against rust-through Drawbar galvanised or black, at manufacturer's discretion Loading ramps hot-dip galvanised

Durumu: kullanılmış, makine/araç numarası: 0e87837859aec926e9db10456, boş ağırlık: 6.200 kg, azami yük ağırlığı: 11.800 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 05/2018, lastik boyutu: 235/75 r17,5, Üretim yılı: 2017, Further information Chassis: Steel welded construction, double-cranked with low-bed sections in front of and behind the axle assembly; low-bed sections are beveled for drive-in capability; turntable with heavy-duty ball race ring; foldable rear support; wheel chocks; side underrun protection; quarter shell mudguards. Lashing eyes: Over the front axle: 2 pairs of ring lashing eyes, each rated to 5 tons, at the cranked section. Low-bed/rear axle: 6 pairs of lashing eyes, each rated to 8 tons, located laterally in the low-bed section. 6 pairs of lashing eyes, each rated to 5 tons, positioned between the longitudinal beams. Pair of stake pockets recessed into the outer frame (internal dimension 70 x 40 mm), or, as an alternative to stake pockets, 5-ton ring lashing eyes recessed in the floor. Drawbar: Certified 40 mm towing eye. Axles: BPW drum brake axles. Fedpfei Ri N Ujx Adgspd Braking system: 2-line compressed air braking system; spring-loaded parking brake; 2 non-interchangeable coupling heads at front. Electrics: 24V electrical system; multi-chamber lights; side marker lights in yellow; 2 white position lights at the front; 2 white/red outline marker lights at the rear; rotating beacon with bracket; pair of illuminated, extendable warning panels (extendable up to 3,000 mm); 2 x 7-pin non-interchangeable connectors at front. Floor: Front cranked section with steel/chequer plate covering; storage box integrated into the drive-on bevel to the cranked section; drive lane area and central area between the beams with steel/chequer plate covering; rear bevel with 70 mm softwood floor; low loader loading area including rear bevel: 5,900 mm. Loading ramps: Hook-on bar for aluminium ramps across the full width, U-profile across the full width; pair of aluminium ramps, each 800 mm long and approx. 400 mm wide; load-bearing capacity per pair: 14,000 kg; ramp storage compartment between the beams. Approval: Contour marking with reflective strips according to ECE R 048; white at the sides and red at the rear.

Durumu: yeni, makine/araç numarası: ccd5fddabaca94f260d9fe895, boş ağırlık: 2.950 kg, azami yük ağırlığı: 15.050 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 445/45 r19,5, Further Information Chassis: Swap-body Turntable Trailer Fine-grained steel welded construction Fliegl V-Stream frame Front stop, adjustable longitudinally and foldable 2 pairs of guide rollers, removable, front and rear 4 container locks with robust outriggers, on 20-foot basis for swap bodies 7.15 and 7.45 Turntable with heavy-duty ball race ring 2 wheel chocks with holders Aluminum side underrun protection Side underrun protection set inward for optimal clearance to the swap body supports Steel rear underrun protection Rear underrun protection shortened for optimal clearance to the swap body supports, lighting system mounted protected Quarter mudguards front and half mudguards rear Towing device: Turntable trailer Tow bar with tested 40 mm towing eye Axles & Suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Brake System 2-line compressed air brake system Colored line routing for easy maintenance Air reservoir 208 liters Spring-loaded parking brake 2 fail-safe coupling heads at front with connecting lines to the towing vehicle EBS, Electronic Brake System with EBS plug at the front, with connection cable Note: The trailer may only be towed by vehicles that ensure ABS effectiveness! With lift & lower valve, holding function in both raising/lowering positions Wheels and Tires 445/45 R19.5, manufacturer at manufacturer's discretion Fpodpoi Ri Rkjfx Adged Steel rims, factory silver Electrics 24 Volt, multi-chamber lamps, yellow LED side lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connection cable 2 additional LED work lights at the rear, operated via reversing light 1 LED work light centrally at the front between the beams, rear-facing, operated via reversing light Country Registration / Plates Germany With Dekra approval and certificate (in accordance with §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour markings with reflective tape according to ECE R 048, white on the sides and red at the rear Paint Frame: DB 7350 Novagrau 10-year warranty against rust-through Note: Archive images!

Durumu: yeni, makine/araç numarası: d9c951d746f03c05bc5470f89, boş ağırlık: 5 kg, azami yük ağırlığı: 29.045 kg, toplam ağırlık: 35 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, Further Information Chassis Semi-Trailer Forwarding Fine-grain steel welded construction, fifth-wheel plate with interchangeable 2-inch kingpin Vario stanchion system 4 pairs recessed into the loading area, collapsible to 2,100 mm and extendable to approx. 3,500 mm for loading. Stanchions can be locked at 100 mm intervals for an internal width of 2,100 mm to 3,000 mm, 4 pairs of divisible stanchions 600 mm + 1,200 mm, total height 1,800 mm, removable. For an internal stanchion width above approx. 2,350 mm, oversize width. Vario bulkheads Floor prepared for the installation of 3 bulkheads. 4 x 5 pairs of Vario stanchion pockets for plug-in bulkheads (front and rear respectively), and 1 x 3 pairs each in the center for transporting welded mesh of 2 x 5,000 mm or 2 x 6,000 mm 2 Vario bulkheads, each consisting of 1 pair of plug-in stanchions and 1 crossbeam at the top approx. 2,200 mm wide. Crossbeam extendable by 220 mm on each side, with lashing hole for securing. Height of Vario bulkhead approx. 1,900 mm, adjustable to 1,300 mm or 700 mm. 4 stanchion pockets recessed in the center of the floor for 80 x 80 mm plug-in stanchions 1 pair of supports at the bottom for front Vario bulkhead 1 pair of supports at the bottom for rear Vario bulkhead Outer frame with slight incline, with Load-Lock profile for lashing strap hooks 14 additional pairs of lashing eyes recessed in the outer frame, 5 tons each 24 t, 2-speed landing gear, single-side operation, with straight lower section, without compensating device Pull-out ladder at rear Wheel chocks with holder Aluminum side underrun protection Galvanized steel rear underrun protection Quarter fenders in front of and behind the axle assembly With anti-spray mud flaps only on the last axle Rear impact guard 8 construction steel winches with wire rope and counter hooks, 4 left and 4 right, with wire rope routing through the outer frame, 1 removable plug-on transmission for construction steel winches – supplied loose (without frame mount) 1 spare wheel holder for 1 E-wheel, with wheel fastener set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, can be locked with a padlock (lock not included) 1 stanchion storage box closed, open at the top, below the loading area, doors on both sides, w=450 mm / h=400/420 mm / d=2460 mm 4 lashing/stanchion rails set transversely in the floor across the full width to the outer frame (max. usable internal width between the outer plug-in stanchions approx. 2,170 mm), approx. 100 mm high. With 20 mm round steel bars, top and bottom, spaced approx. 60 mm apart (of the round steel). Bottom finishes with angle steel, half open downwards. For lashing and plugging in 80 x 80 mm stanchions. Fjdpfxoi Ri R De Adgepd Note: Stanchion pockets/plug-in stanchions are not designed solely for securing long loads, pipes, etc. without lashing Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser aligned to reduce tire wear and fuel consumption Air suspension 1st axle with automatic lift axle, including forced lowering and starting aid, activated by braking 3x (starting aid works up to 30% axle overload and up to a max speed of 25 km/h) Axle lift below the recommended driving height, therefore no warranty for tire damages Brake system 2-line compressed air brake system, color-coded line routing for easy service Spring-actuated parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at front, no c

Durumu: yeni, makine/araç numarası: 357314e4e176f8758d11ba42b, boş ağırlık: 4.500 kg, azami yük ağırlığı: 30.500 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, Further Information Chassis Semi-Trailer Tipper Fine-grain steel welded construction, lightweight design, fifth wheel plate with interchangeable 2-inch kingpin Curved front wall patented telescopic support centrally mounted, uncoupling while loaded not possible; when uncoupled, the vehicle must be positioned with a rear tilt. 2 wheel chocks with holders collapsible underrun protection half-shell mudguards integrated mudguard holder with stone-repellent surface equipped with anti-spray mud flaps only on the rearmost axle 1 tarp rod with holder 2 tow hooks at rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter axle/chassis laser measurement to reduce tire wear and fuel consumption axles in off-road version, air suspension 1st axle automatic lift axle, including forced lowering and start-up aid, activated by 3x brake application (start-up aid operates until axle overload exceeds 30% and up to a maximum speed of 25 km/h) hot-dip galvanized lift axle mechanism, 10-year corrosion warranty Braking System 2-line compressed air braking system, color-coded piping for easy servicing. spring-loaded parking brake Fjdpfx Asi Ri R Isdgspd 2 non-interchangeable coupling heads at the front, without connecting line EBS (Electronic Braking System) with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractors capable of ensuring proper ABS functionality! with raise & lower valve Vehicle stability system Automatic tipping lowering with shut-off valve Wheels and Tires 385/65 R22.5, make at manufacturer's discretion steel rims, factory silver Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lamps at front 2 white/red outline marker lamps at rear 2 x 7-pin non-interchangeable sockets at front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupler, fixed part, nominal width 48 mm (without hose connection) hydraulically operated via truck PTO tipper bodies aluminum box body made from high-quality, wear-resistant material, front wall 5 mm thick, with external side walls of 30 mm hollow-chamber profiles, neatly welded, with bulk material-repellent upper rail profile. Internal access steps on front wall (not in conjunction with Cramaro). External scoop and broom holder on front wall. Greenline – conical and aerodynamic body design Membrane – rear wall Rear wall as pendulum flap with dual-hinge, externally mounted with double hook locking. Rear wall with rubber seal Note! Heat resistant up to max. 170°C! Floor 6 mm throughout Platform with access, connection plate for air/electrics and brakes, providing ample space for optimal operability. Roll tarp deposited on passenger side, with central locking on driver’s side Operating Notes For transporting salt, lime, etc., we recommend a tipper cylinder with a hard-chromed piston rod to prevent damage and corrosion by the material. The specified gross weight is technically feasible; depending on cargo, the gross weight may not be achieved within the permissible axle/support and fifth wheel loads. (Poor driving and tracking behavior may result from incorrect load distribution) Approval / Plates Germany Approval per EC 2007/46 24/7 service hotline preparation for single-line license plate holder contour marking with reflective tape per ECE R 048, white sides and red rear

Durumu: yeni, makine/araç numarası: 59ade5d1599dcdee29033ac46, boş ağırlık: 6.350 kg, azami yük ağırlığı: 28.650 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 435/50 r19,5, Further information Chassis Fifth Wheel Forwarder Fine-grain steel welded construction, fifth wheel plate with replaceable 2" kingpin Insert bar for aluminum ramps across the entire width Frame in reinforced version for vehicle loading (up to the outer frame) Outer frame with load-lock profile approx. every 400 mm for lashing strap attachment 10 pairs of lashing pins flush-mounted on top/outside of the outer frame, each rated at 10 t 24 t, 2-speed landing gear, single-sided operation, with semicircular lower part and straight mounting plate, with thrust compensation Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection Galvanized steel rear underrun protection Quarter-circle mudguards in front of 1st axle and behind each axle With anti-spray mudflaps behind each axle Pair of ferry lashing points, marked in yellow 1 spare wheel holder for 1 single wheel, with wheel fixing kit 2 plastic toolboxes, with drawer and storage shelf, w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) Container locks: 4 pairs of locks recessed in the floor for 2 x 20 ft or 1 x 40 ft container, frontmost position as fold-down lock, countersunk 10 pairs of stake pockets recessed in the outer frame, 70 x 40 mm internal dimensions 10 stake pockets centrally recessed in the floor, 70 x 40 mm internal dimensions 2 cross lashing/stake rails inset into floor across the full width up to the outer frame (max. usable internal width between the outer most removable stakes approx. 2170 mm), approx. 100 mm high. With 20 mm round steel rails, both top and bottom, distance between upper and lower approx. 60 mm (of the round steel). Lower part finished with angle sheet, half open downwards. For lashing and inserting stakes 80 x 80; arrangement: positions 2 and 4 according to Fliegl data sheet 20 removable stakes, hot-dip galvanized Note: Stake pockets/inset stakes are not designed for sole load securing of long material, pipes etc. without lashing Storage space for aluminum drive-on ramps, ramps can be inserted from the rear Fpodpeld Ihljfx Adgjd 3 pairs of fold-down lashing eyes 10 t in the outer frame (1x in front of front wall and 2x in the rear area) Axles & Suspension SAF disc brake axles Axles/chassis laser-measured — reduces tire wear and fuel consumption Air suspension 1st axle automatic lift axle with forced lowering and traction aid, operated by 3x brakes (traction aid operates up to 30% axle overload and a max speed of 25 km/h) Axle lift below recommended driving height, therefore no warranty for tire damage 2 ride heights, adjustable via manual control, 1 x for coupling height 980 mm, 1 x for coupling height 1100 mm (Note! Vehicle with inclined position) Braking system 2-line compressed air braking system Colored line routing for easy service Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With raise & lower valve 2 ride heights, adjustable via manual control, 1 x for coupling height 980 mm, 1 x for coupling height 1100 mm (Note! Observe total height, overheight at customer’s risk) Ride height in conjunction with lift axle, with lifted axle the loading or total height increases by 50 mm (for Mega Flex only at low ride height/coupling height) Vehicle - driving stability system Wheels and tires 435/50 R19.5, make at man

Durumu: kullanılmış, HKL 22 (0011) Lindner ve Fischer HKL 22 (0020) Şasi No: W09400222B0L13631 Fpedox Uuh Espfx Adgod (0030) ikinci el

Durumu: kullanılmış, boş ağırlık: 3.500 kg, azami yük ağırlığı: 14.500 kg, toplam ağırlık: 18.000 kg, ilk tescil: 04/2009, bir sonraki muayene (TÜV): 12/2025, yükleme alanı uzunluğu: 7.600 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.850 mm, yükleme alanı hacmi: 53 m³, süspansiyon: hava, lastik boyutu: 245/70R17,5 144/144J, renk: yeşil, vites türü: diğer, ön lastik ölçüsü: 245/70R17,5 144/144J, arka lastik boyutu: 245/70R17,5 144/144J, şoför kabini: diğer, emisyon sınıfı: hiçbiri, Donanım: ABS, basınçlı hava freni, Registration service, General inspection / Safety inspection / Accident prevention inspection, Delivery to port Languages: German, Russian, English, Arabic Fodpfxoww D Ite Adgspd Also available as a complete truck and trailer combination!! Base color: green Equipment extras: ABS, turntable, air brakes, EBS, air suspension, price on request (Mobile), disc brakes, suspension: air/air, payload (kg): 14,500 Body type: Top condition, side wall on the inside. General inspection / Safety inspection valid, HSN/TSN: 7951/000 Subject to errors and changes.

Durumu: kullanılmış, boş ağırlık: 6.372 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 04/2015, süspansiyon: hava, lastik boyutu: 385/65 R22,5, renk: siyah, Üretim yılı: 2015, Donanım: ABS, Boş ağırlık: 6372 kg, Azami yüklü ağırlık: 35.000 kg, Sertifikalı yük emniyeti. Lastik ebadı: 385/65 R22.5, DIN EN 12642 (kod XL) sertifikası, 1. dingil: , 2. dingil: , 3. dingil: , Havalı süspansiyon, Arka alttan koruma, Elektronik Fren Sistemi (EBS), Yangın söndürücü yuvası, Takım kutusu, Çift yedek lastik yuvası, Civatalı şasi, Kayar tavan, 1x15 ve 2x7 pinli fiş, Mevcut tüm araçların genel görünümünü web sitemizde bulabilirsiniz. Finansman mı gerekli? Size özel finansman çözümleri, tam hizmet sözleşmeleri ve telematik hizmetleri sunuyoruz. Size şahsen danışmaktan memnuniyet duyarız. Fpedpfx Adjyl Atpjgjd

Durumu: kullanılmış, azami yük ağırlığı: 33.520 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 08/2011, Donanım: ABS, Vehicle identification no.: WFDFLT33502005191 REAR TIPPER – Steel chassis – ALU body German MOT (HU) valid until 04/2026 – Safety inspection (SP) until 10/2025 Unladen weight: 5,480 kg Body dimensions: 8,350 / 7,500 x 2,460 x 2,200 mm – Capacity: approx. 43 m³ BPW Eco Plus axles with drum brakes 1 x aluminum landing leg Combination – swing doors – pendulum tailgate with 2 x sliders Rolling tarpaulin Platform Fpsdswpbg Dopfx Adgod Adjustable underrun protection Tyres: 385/65 R 22.5 Aluminum wheels Subject to alterations, prior sale, and errors excepted. The description is for general vehicle identification only and does not constitute a warranty in the legal sense. The specification according to the purchase contract is binding. Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is required, we are happy to provide an offer through our partner workshops! Vehicle may be fitted with advertising stickers and/or lettering. Our general terms and conditions for delivery and payment apply.

Durumu: kullanılmış, azami yük ağırlığı: 30.200 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2019, bir sonraki muayene (TÜV): 06/2025, yükleme alanı uzunluğu: 7.200 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 1.750 mm, yükleme alanı hacmi: 30 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.380 mm, Donanım: ABS, Fliegl DHKA 390 SDS01 30m³ Rear Tipper Aluminum Lightweight Tipping Body 3-axle rear tipper semi-trailer with lightweight aluminum tipping body, Type DHKA 390 – 30 m³ rear tailgate, Fsdpfx Adewr Ry Eegspd Greenline ----### Aluminum Lightweight Tipping Body / Aluminum Box Body ###---- Aluminum tipping body, Volume: approx. 30 m³, Fifth wheel height: approx. 1,200 mm, Gross vehicle weight rating (GVWR): 35,000 kg, Curb weight: 4,800 kg, Payload: 30,200 kg, 1st axle liftable, Roll tarp, can be stowed to the right, with central locking to the left, 2x rear LED work lights, SAF axles, Steel standing platform with anti-slip safety grating and guard rail, Hard chromed tipping cylinder, Rear folding underrun protection, 1x drop leg, Disc brakes, Broom and shovel holders mounted on the front wall, Air suspension, Swinging tailgate with mechanical 2-hook locking, Swinging rear/tailgate sealed with rubber gasket, Sidewall bolt locks, 1x grain chute, 1x left side toolbox, 1x front toolbox, Mudguards on all wheels, Loading area dimensions LxWxH: approx. 7,200 x 2,420 x 1,750 mm, Sidewall height: approx. 1,750 mm, Loading height: approx. 3,239 mm, Overall dimensions LxWxH: approx. 8,600 x 2,550 x 3,340 mm, Wheelbase: 3,100 x 1,310 x 1,320 mm, Tires: 385/65R 22.5 on aluminum rims, Tread depth left front: 14 mm, Tread depth left center: 14 mm, Tread depth left rear: 4 mm, Tread depth right front: 12 mm, Tread depth right center: 15 mm, Tread depth right rear: 12 mm, Tipping floor worn Additional Equipment: Overall length: approx. 8,600 mm, Overall width: approx. 2,550 mm, Overall height: approx. 3,340 mm, Internal body height: approx. 1,750 mm, Volume: approx. 30 m³, Fifth wheel height: approx. 1,200 mm, Neck height: approx. 190 mm, King pin installation dimension: approx. 600 mm, Central telescopic support leg, Uncoupling with load not possible, when uncoupled, the vehicle must be parked with a rearward incline, Folding underrun protection, Half-shell mudguards, Tarp pole with bracket, Aluminum ladder approx. 3,550 mm, with side mounting bracket, SAF disc-braked axles, Air suspension, 1st axle with automatic lifting function, additionally can be operated electrically from the truck, with start assist function, does not require installation on the truck (start assist is functional up to 30% axle load exceedance and a maximum speed of 25 km/h), Spring-actuated parking brake, EBS—Electronic Braking System with EBS socket at the front, without connection cable, Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! 24 Volt, 4x 3-chamber rear lights + 1 round reversing light + 1 round rear fog light, all LED, 2 white position lights at the front, 1x 15-pin electrical socket at the front, without connection cable, Low-pressure cylinder max. 170 bar, with HDK screwed coupling, fixed part, NW 48 mm, Hard chromed tipping cylinder, Body: Aluminum box body made of high-quality, wear-resistant material, Sloped front wall 5 mm thick, With externally mounted cylinder, Side walls made of 30 mm hollow chamber profiles, cleanly welded, With anti-spill upper rail profile, Greenline – conical and aerodynamic body design, 'membrane' rear wall, Rear wall as swinging tailgate, external, with dual hook locking, Rear wall with additional side and bottom clamping bolts, Rear wall with rubber seal, Note! Heat resistant up to max. 170°C !, Central grain slider, Floor continuous 6 mm thick, Wear-resistant edges at the rear side walls,

Durumu: kullanılmış, makine/araç numarası: WFDFLT33902010171, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2013, renk: diğer, Üretim yılı: 2013, Daha fazla bilgi için lütfen bizimle iletişime geçin. Fjdpfx Aeyhb H Hjdgspd

Durumu: kullanılmış, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 05/2015, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.520 mm, Donanım: ABS, Schmitz Cargobull S01 platform treyler, kaldırılabilir aks ve SAF akslar Fpsdpfxjyavigs Adged Sorgular için dahili numara: 1225958 * ABS * EBS * 3 adet havalı süspansiyonlu aks * Kaldırılabilir aks * Disk frenler * SAF akslar Yükleme alanı uzunluğu: Uzunluk: 13.600 mm * Genişlik: 2.520 mm Lastikler: 1. aks: 385 / 55 R 19,5 %30, havalı süspansiyon / kaldırılabilir aks 2. aks: 385 / 55 R 19,5 %30, havalı süspansiyon 3. aks: 385 / 55 R 19,5 %30, havalı süspansiyon ----Fiyat: 3.900,- EUR + %19 KDV Daha fazla bilgi için aşağıdaki telefon numaralarından bize ulaşabilirsiniz: * Konuşulan diller: Almanca, İngilizce, Fransızca, Lehçe ve ???? Yazım hataları, yanlışlıklar ve ara satış hakkı saklıdır.

Durumu: kullanılmış, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: WFDFLT33902028370, boş ağırlık: 6.015 kg, azami yük ağırlığı: 28.985 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, izin verilen dingil yükü (dingil 1): 9.000 kg, izin verilen dingil yükü (dingil 2): 9.000 kg, izin verilen aks yükü (aks 3): 9.000 kg, ilk tescil: 04/2021, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 13.650 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.000 mm, toplam uzunluk: 13.850 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.030 mm, süspansiyon: hava, lastik boyutu: 435/50 R19,5", renk: siyah, Üretim yılı: 2021, Donanım: EBS (Elektronik Fren Sistemi), Chassis semi-trailer for haulage Fine-grain steel welded construction, fifth wheel plate with replaceable 2" king pin Outward frame slightly inclined with “Load-Lock profile” for lashing strap attachment, if fitted to the frame. Note: To hook the straps in combination with side walls, the side walls must be opened! 24 t, 2-speed landing gear, one-sided operation, with straight lower section, without compensation for telescopic movement Note: Free landing gear foot corner dimension or free swing-through radius at the rear approx. 1930 mm, without supports. Extendable ladder at the rear, door retainer to the side 2x wheel chocks with holders Side underrun protection in aluminium Rear underrun guard, galvanized steel Quarter-shell mudguards in front of the 1st axle and behind each axle With anti-spray mudflaps behind each axle Rear buffer, pallet stop on both sides approx. 15–20 mm high, bolted design, reduces loading height by approx. 15–20 mm Plastic toolbox with drawer and shelf, dimensions w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) Axles & Suspension SAF disc brake axles “Axle/chassis laser alignment”: Reduced tire wear and fuel consumption, air suspension, without lift axle Brake System 2-line compressed air brake system, colour-coded piping for easy servicing. Spring-loaded parking brake 2 fail-safe coupling heads at the front, without coupling line EBS, electronic braking system with EBS socket at the front, no connection cable Note: The trailer may only be towed by tractors that ensure the effectiveness of ABS! With lift & lower valve Vehicle stability control system Wheels and Tires 435/50 R19.5”, tyre brand at manufacturer’s discretion, alternatively 385/55 R19.5 Steel rims, factory silver finish Electrics 24 Volt, multi-chamber lights, amber LED side marker lights 2 white position lights at the front 2 white/red demarcation lights at the rear 2 x 7-pin and 1 x 15-pin fail-safe sockets at the front, without connection cables Floor Resin-coated plywood panels approx. 30 mm thick, laid on longitudinal crossmembers for high point load capacity, suitable for forklift axle loads up to max. 7,100 kg Body Body mounted Front wall / front corner posts 2,580 mm high, corner posts made of steel in volume design, release mechanism for side curtain at front wall, “Crash blocker”, lower internal, with steel buffer at approx. 140 mm height Centre posts 3 pairs of sliding posts, adjustable along full length, with 4 pocket receptacles each and extended pocket at the bottom 3 pairs of post positions Insert slats 5 rows of wooden insert slats Fpodpfx Aex Sqmrsdgjd Rear wall / rear corner posts Rear corner posts in steel, up to the lower edge of the roof, curtain rail with round tube and tensioning ratchet Rear portal doors, double-wing, each with two internal locking rods Curtain Curtain with welded horizontal and vertical straps Tensioners made of stainless steel Roof Sliding roof, rear end-lift hinged upwards, sliding from rear to front, L-roof rail for automotive industry, internal width between roof rails approx. 2,490 mm, curtain colour: white Non-elastic roof, minimal bending of roof rail during loading/unloading EcoLift – roof raisable by approx. 380 mm, both sides, with gas strut assistance, 3 driving positions at the front: internal front height approx. 2,900 mm / 2,950 mm / 3,000 mm, factory set to approx. 3,000 mm Optimized rear rain gutter, at top of rear crossmember, above doors

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2005, = Diğer seçenekler ve donanımlar = - Arka havalı süspansiyon - Ön havalı süspansiyon = Açıklamalar = 3 dingilli, üzerinden geçilebilir alçak şasi treyler. Çeki platformu, rampalı yaklaşık 4.000 x 2.500 mm, alçak yükleme platformu yaklaşık 9.200 x 2.500 mm. Yükleme yüksekliği yaklaşık 920 mm. 44 bağlama halkası ve yük sabitleme halkası. İki parçalı hidrolik rampalar yaklaşık 2.150+1.250 x 630 mm. BPW akslar, ABS, havalı süspansiyon. Azami toplam ağırlık 41.000 kg, king pin yükü 11.000 kg, taşıma kapasitesi 32.100 kg. 2 inç king pin, beşik yüksekliği yaklaşık 1.050 mm. 4 adet alet kutusu. Lastik ölçüsü 235-75R17.5. 2 hatlı hava sistemi, hidrolik ünite. Renk: beyaz. = Diğer bilgiler = Boş ağırlık: 8.900 kg Yük kapasitesi: 32.100 kg toplam ağırlık: 41.000 kg Fsdoyaxnfspfx Adgepd Ön lastik: 235-75 R 17.5 Arka lastik: 235-75 R 17.5 Daha fazla bilgi için Jan-Marc Schwickert ile iletişime geçin.

Durumu: kullanılmış, makine/araç numarası: WFDFLT23861001990, boş ağırlık: 4.900 kg, azami yük ağırlığı: 33.100 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, toplam uzunluk: 9.800 mm, toplam genişlik: 2.550 mm, lastik boyutu: 265/70 r19,5, renk: kırmızı, Further information Former exhibition vehicle from 2006 – was used internally and therefore shows signs of use/wear! Side underrun protection: aluminium, from king pin to start of side underrun protection 2,600 mm Rear underrun protection: Chassis colour and flush with the end of the chassis, positioned as far inwards as possible Wheel chocks: 2 units with brackets Bump stops: 2 steel buffers Fpsdpfxei Ri Hye Adgsd Paint: sandblasted base, 2-component acrylic paint Rims: factory silver Inspection: with DEKRA approval