Roll-off dorse

MÜLLER-MITTELTAL 24 to. Kombi Cont. fl.-Liftachse NEU

Koşul: yeni, azami yük ağırlığı: 18.900 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TRA-Kombi 24.0: ----Braking System: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual rear lowering ----Axle: * 3 x 11 t Gigant axles * Middle axle liftable ----Drawbar: Dcsdpfx Aepk D Awsldjg * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye & height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Fittings: * Tool box made of powder-coated sheet steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets, made of galvanized sheet steel (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffer * Mechanical drop-down supports at rear ----Container / Low Loader Deck: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide roll-off containers * Steel floor with recessed rollers in the bogie area * When transporting roll-off containers, container lengths from 5,500 to 7,000 mm possible * Pneumatic 4-point container locking as well as mechanically insertable end stops at the front in the guide rails * Load securing certificate in accordance with DIN 30722-1 * Transport of up to 2 skip containers with a max. volume of 10 m³ possible * 8 movable skip stops for lateral centering of the skips, front 4 skip stops insertable with oscillating end stop ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips * 4 side lashing cleats (cloverleaf design) and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Welded anti-slip strip in the running area of the ramp incline * 1 pair of aluminum approach ramps (16 t / pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Tires: * Tires: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Side and rear contour tape, reflective * Axles, turntable, drawbar, and air tanks painted black * Hot-dip galvanized main frame ----Information: * Technical permissible gross weight up to 27,000 kg * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from approx. week 47/2026

Koşul: mükemmel (kullanılmış), dingil konfigürasyonu: 2 dingil, izin verilen dingil yükü (dingil 1): 12.000 kg, izin verilen dingil yükü (dingil 2): 12.000 kg, ilk tescil: 03/2015, yükleme alanı uzunluğu: 134.450 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 480 mm, süspansiyon: hidrolik, Üretim yılı: 2015, Donanım: ABS, = Diğer seçenekler ve donanımlar = - Merkezi yağlama = Diğer bilgiler = Aks konfigürasyonu Süspansiyon: hidrolik süspansiyon Arka aks 1: Maks. aks yükü: 12.000 kg; Yönlendirilebilir Arka aks 2: Maks. aks yükü: 12.000 kg; Yönlendirilebilir Ağırlıklar Boş ağırlık: 12.660 kg Yük kapasitesi: 34.340 kg Azami toplam ağırlık: 47.000 kg Fonksiyonel Dcjdpfx Aevtc Aieldog Yükleme platformu yüksekliği: 48 cm Çekilebilir üst yapı: Evet Durum Teknik durumu: çok iyi Görsel durumu: çok iyi Finansal bilgiler Fiyat: Talep üzerine Diğer bilgiler Daha fazla bilgi için David F Middelman ile iletişime geçiniz.

Koşul: yeni, azami yük ağırlığı: 18.900 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual rear lowering ----Axle: * 3 x 11 t Gigant axles * Center axle can be lifted ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment ----Electrics / Lighting: * LED tail lights * 15-pin power connector * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Tool box made of powder-coated steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray suppression * Plastic rear bumper pads * Mechanical rear safety support legs ----Container / Low-loader Platform: * Hot-dip galvanized main frame with raised outer rails (approx. 25 mm higher) for guiding roll-off containers * Steel floor with roller depressions in the turntable area * For roll-off container transport, container lengths from 5,500 - 7,000 mm possible * Pneumatic 4-point locking system and mechanical plug-in end stops at the front of the running rails * Load securing certificate as per DIN 30722-1 * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Includes 8 removable skip container stops for lateral centering, front 4 stops with swingable end stop ----Load Securing: * 3 pairs of 10 t UVV lashing rings on each side for attaching tie-down elements for positive and non-positive securing of skip containers * 4 cloverleaf-style lashing bars (each side) and 1 pair of 13.4 t UVV lashing rings to the front * Load securing certificates per DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 ----Ramps: * Welded bead as anti-slip surface in the ramp track area * 1 pair of aluminum approach ramps (16 t/pair), 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from rear) ----Tires: Dcedpfx Aletplv Tjdog * Tires: 235/75 R17.5 ----Ride Height: * Loaded ride height approx. 1003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides & rear * Axles, turntable, drawbar and air tanks painted in a shade of black * Hot-dip galvanized main frame ----Info: * Gross vehicle weight of 27,000 kg technically possible * New vehicle without initial registration, with manufacturer warranty * Errors and prior sale reserved ----Delivery Time: * Available from approx. week 47/2026

Koşul: yeni, azami yük ağırlığı: 67.200 kg, toplam ağırlık: 85.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of vehicles, including immediately and short-term available units, on our website. Extract from the specification. Full equipment details available on request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° * For tractor units: 6 x 2, 6 x 4, and 8 x 4 short * Detachable steel front bulkhead, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flush-mount lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized finish * 1 plug-in ALU tailboard, approx. 400 mm high, anodized finish * Approx. 40 mm strong hardwood flooring above the gooseneck, checker plate flooring above the kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, incl. overhead gallows for securing supply lines (Faymonville couplings) * 2 pairs of stake pockets recessed in the gooseneck for plug-in stakes approx. 100 x 50 mm LOADING PLATFORM Dcjdpfxsrgzv Ne Aldeg * Extendable loading platform, length approx. 11,000 mm, rear bevel approx. 500 mm x 10° * Pneumatic locking system with conical locking bolt and reinforced locking positions; supply lines are protected within the extendable beams and automatically adapt to the respective platform length * BPW axles and suspension, 1st axle self-steering, 2nd axle rigid, all other axles hydro-mechanically forced steering * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * Tyres: 235/75 R 17.5 3PMSF twin tires * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous hardwood flooring, approx. 50 mm thick, on the loading platform and interrupted between the axles (providing increased friction coefficient) * Slotted holes for suspended and repositionable bridging elements: - on the fixed section behind the gooseneck - at the front of the platform * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate covering, slotted holes front and rear for suspended and repositionable bridging elements * 1 pair of flush-mounted lashing rings, lying, in the fixed front section of the loading platform (LC 10,000 daN) * 9 pairs of flush fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle alignment monitoring, without installation in the tractor * 1st axle with automatic lift axle function and starting aid according to EU Directive 2021/535 * Below the gooseneck and at the rear cross member, left and right, a 7-pin socket each with bracket for warning signs * Painted-on sand coating on the outer frame of the platform, the checker plates, and the transition area between the loading platform and...

Koşul: yeni, azami yük ağırlığı: 31.500 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, Donanım: ABS, Wiese 3-axle semi-trailer with lift table and foldable tail section. Ideal for transporting forklifts and/or aerial work platforms. Technical Specifications: - 3 x 10 t axles - Lift axle - Steering axle with Smart Steering (steers forward and reverse) - Outer beam chassis with incline - Gooseneck design rated for 18 t, suitable for 2- and 3-axle tractor units - Hydraulic lift table adjustable in 3 positions - Rear in tailgate version including hydraulic extensions, usable as loading ramps, drive-over ramp or loading area (total length reduced when tailgate is upright) - Remote control for ramps and lift table - Front wall - Grated floor - Numerous lashing points - SmartBoard - Central lubrication system - Steel construction, hot-dip galvanized and painted Djdpfx Ajvw Hmtsldocg A wide range of options available on request, for example: - Winch - Toolbox on the fifth wheel step - Aluminium rims Further information available upon request.

Koşul: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, 3-axle MULTIMAX PLUS low-loader semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross weight: 49,500 kg or 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Coupling height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: (value not specified) Loading area width approx.: 2,540 mm Loading height at max load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific legal limits are exceeded. Technical Description Gooseneck: SNT design gooseneck to optimize loading platform length, approx. 3,900 mm length, with rear chamfer approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading area: Loading platform approx. 9,600 mm length with rear chamfer approx. 900 mm x 6°. Section after the gooseneck is hydraulically raisable/lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS Pair of two-section AXS steel ramps, approx. 4,920 mm long and 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Each ramp hydraulically shiftable approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle as per technical datasheet: C470319. Maximum gradient at lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg. Air suspension with lift/lower valve. Axle tools included. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion. Load index 143/141J (144/144F). Braking system: WABCO EBS-E braking system per EU regulations. No cables to the tractor unit. Lighting system: 24V "ASPÖCK-NORDIK full LED" lighting per EU regulations (ASS 3). Dodpfx Alsizu Ntsdocg Metallisation: Complete HRM (High Resistance Metallisation). Full steel structure shot-blasted, then hot-coated with ZINACOR 850 (85% zinc / 15% aluminium). Painting – 6-stage finish: - Complete steel structure shot-blasted after welding - 1 coat zinc-based primer, 1 coat adhesion primer - Top coat with 2 coats 2K acrylic paint, single colour in RAL shade of choice - Cavity sealing with special wax - Rims in silver - Multicolour & special paint available at extra cost Steel structure: High-tensile fine-grain steels Types: S355J2+N/S355MC (yield stress 355 MPa), S690QL/S700MC (yield stress 690 MPa) Welders certified to DIN-EN 287-1, MAG welding per EN ISO 4063, M21 shielding gas as per EN ISO 14175. Front wall: Removable steel front wall, approx. 400 mm high. Supply connection strip for connections to tractor unit, fitted at outer frame profile height. ASPÖCK-UNIBOX at the front supply strip with 24N, 24S & 15-pin sockets. - 24N connection per ISO-1185 - 24S connection per ISO-3731 - 15-pin connection per ISO-12098 If your pin assignment deviates from the ISO standard, please inform us. "Anderson" socket on front supply strip: Rema 78051-00 & Amp. 150 V. Cable for the supply of the electro-hydraulic power pack and/or electric winch (35 mm²,

Koşul: ikinci el, azami yük ağırlığı: 42.500 kg, toplam ağırlık: 60.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2022, with 12 axles, split, hydraulically suspended, hydromechanical forced steering, with rear bevel and drive-on ramps STZ-L gooseneck - robust steel welded construction - designed loading area: 3,950 x 2,480 mm including bevel - hydromechanical forced steering (dual circuit steering) - turntable-mounted saddle plate with replaceable 2 or 3.5 inch king pin and adjustable steering wedge - fifth wheel load: 24 t - steering radius to rear: 2,600 mm Loading Area - recessed outer sections: 4,630 mm, 420 mm deep, providing a loading height of 470 mm or 830 mm with decks installed - extendable by 2,053 mm - including aluminium bridging ramps for creating a level platform - excavator arm trough at rear chassis: 4,900 mm long, 880 mm wide, 480 mm deep - rear chassis length: 4,900 mm incl. 500 mm bevel, loading height 890 mm - one pair of wheel recesses in the lower loading area - hydraulically suspended 3-axle chassis - split Gigant axles with 600 mm lift Rear of vehicle - design: “Beveled” 500 mm - hydraulic rear support Drive-on ramps - two-piece drive-on ramps, length 2,850 + 1,850 mm, width 800 mm - rubber coating with climbing strips Braking System Dedpfx Aow Etd Teldecg - two-line all-wheel pneumatic brake system with diaphragm brake cylinders - automatic load-dependent brake (ALB) - automatic linkage plates (AGS) - parking brake via spring-loaded cylinders - ABS/ABV brake Special equipment Radio remote control for steering and ramp control Central lubrication system Technical data Gooseneck Loading area (LxW): 3,950 x 2,480 mm Saddle height loaded: 1,300 mm Loading area Loading platform (LxW): 10,030 mm x 2,850 mm, extendable by 2,053 mm recessed outer sections 4,630 mm long plus 2,053 mm extension center beam 980 mm excavator arm trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st axle to 3rd axle: hydromechanically forced steering (dual circuit steering)

Koşul: yeni, boş ağırlık: 10.900 kg, azami yük ağırlığı: 37.100 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 890 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17.5, renk: gri, işletme ağırlığı: 10.900 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear with approx. 1,000 mm x 6° chamfer - Technical fifth wheel load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading Platform: - Loading area, approx. 9,600 mm long, with chamfer at the rear approx. 900 mm x 6° - Loading area behind the gooseneck hydraulically raiseable and lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg Dcedpfxouadk Ne Aldog - Grating surface and approx. 5 mm steel plate as additional reinforcement on the chamfered section of the loading area Ramps: - One pair of two-piece AXS steel ramps, approx. 4,675 mm long, approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 365 mm inwards - Painted sand coating on the outer frame of the ramp as well as on the ramp tip - Flashing lights on the outer side of the ramp tips with switch next to the ramp control - Ramp locking in transport position with quick-release fastener Axles, Suspension and Tyres: - BPW axles and suspension, 1st and 2nd axle fixed, 3rd axle self-steering - 1st axle with starting aid - Operated via the brake pedal of the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 - TPMS tyre pressure sensors fitted on all wheels including spares Brake System: - WABCO EBS-E braking system according to EU regulations Paintwork: - Trailer painted MB 7350 Novagrau grey Accessories Included: - Plug-in steel front wall, approx. 400 mm high - 3 kW electric hydraulic power pack for controlling hydraulic operations, except hydraulic winches - Guide plate from gooseneck for the fifth wheel plate, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating surface with 5 mm steel plate underneath as additional reinforcement - Painted sand coating - Cut-outs in the outer frame of the loading platform and lifting bed for attaching hydraulic ramp control valves on the right side of the vehicle - 2" king pin - Central lubrication system with one pump, brand BEKAMAX - On gooseneck, 1 pair of plug-in side ALU folding walls, approx. 400 mm high, anodized - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control - Steel rope approx. 24 m long, rope ø approx. 9.5 mm, incl. rope press roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Koşul: yeni, azami yük ağırlığı: 25.645 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Excerpt from the equipment - full specification upon request. Loading area: - Low-bed with central beam, extendable version, length approx. 6,750 mm - 5 pairs of outward-folding lashing rings (LC 5,000 daN) - 1 pair of outward-folding lashing rings (LC 10,000 daN) - 1 pair of horizontal lashing rings at the rear of the platform (LC 10,000 daN) Gooseneck: - Gooseneck hydraulically raisable/lowerable and detachable Rear running gear: - Rear running gear, short design, with closed outer frame and tread plate cover - Running gear with excavator recess, rear half closed to accommodate air tanks - 2 pairs of outward-folding lashing rings (LC 5,000 daN) - 1 pair of outward-folding lashing rings (LC 10,000 daN) - 1 pair of horizontal lashing rings at the rear of the running gear (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced-steered - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Braking system: - Wabco braking system according to EU regulations, with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) topcoat in RAL 3000 flame red Including the following additional equipment: - 2 king pins - Galvanized steel front wall, height approx. 400 mm - Remote steering override (front and rear) via cable remote control with pushbuttons, with axle tracking control (no installation in the tractor unit) - Electro-hydraulic power unit - Load manometer for axle load determination, incl. load diagram - On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in stanchions are removable (body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switches on the trailer, mounted on the gooseneck platform left and right - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stanchion pockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the loading area, 2 pairs in the outer frame of the running gear - Galvanized extensions, extendable by approx. 230 mm per side - Hydraulic lines from gooseneck to low-bed with multi-coupling instead of screw couplings (no guarantee on seals) - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard grease NLGI-2, with removable pump cover - 2 pairs of WADER container pockets in the loading area, for 1 x 20' container Dcjdpsxf Silofx Aldeg - 1 removable galvanized intermediate platform with 1 pair of WADER container pockets - 1 pair of steel ramps to bridge the pick-up hooks of the low-bed - Sand coating on the loading area as slip protection - HRM metallization (High Resistance Metallization)

Koşul: yeni, azami yük ağırlığı: 36.937 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Üretim yılı: 2026, Donanım: ABS, Kässbohrer Low Loader with Hydraulic Gooseneck Dedot Aqv Sopfx Aldocg Immediately Available! TECHNICAL DATA: * Fifth Wheel Height: 1,250 mm * Total Length: 13,190 mm * Gooseneck Length: 3,950 mm * Platform Length: 9,240 mm * Platform Height: 875 mm * Wheelbase: 8,480 mm * Axle Spacing: 1,360 mm * Axle Load: 30,000 kg * BPW axles with air suspension and drum brakes, 10-ton payload * Unladen Weight: 11,063 kg * Overall Width: 2,550 mm * Permissible Gross Vehicle Weight (60 km/h): 52,800 kg * Permissible Gross Vehicle Weight (80 km/h): 48,000 kg CHASSIS: * 2x fixed front axles, 1x self-steering trailing rear axle * Overload-dependent manual axle lift system on the first axle * 12x 245/70R17.5 tyres * Air suspension, 1x load gauge FRAME: Made of high-quality, high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost landing gears at the front * Foldable supports at the rear * Grated steel platform floor RAMP: * Ramp load capacity: 40 tonnes * 2x hydraulic ramps, suitable for hydraulic sliding/folding operation, galvanized steel surface, 4,200 mm long and 850 mm wide, 9° ramp angle, load capacity 40,000 kg and closed height 3,510 mm * Hydraulic gooseneck ramp, 2,800 mm long, 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6-ton capacity, 6x2 on the platform with 6-ton capacity, 8x2 on the outer frame with 6-ton capacity * 8x2 stake pockets OTHER: * 1x rotating beacon * 1x work light * 2x2 oversize marker boards with lighting * SmartBoard For further information, please do not hesitate to contact us.