Düşük yükleyici

Faymonville 4-axle semi lowbed trailer 73 t ext.

Durumu: yeni, boş ağırlık: 17.500 kg, azami yük ağırlığı: 43.500 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.750 mm, yükleme alanı yüksekliği: 400 mm, lastik boyutu: 245/70 R 17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and removable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, “SUPER LOW” design, length approx. 7,550 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking - Supply lines routed protected inside the extendable beams and automatically adjust to the respective lowbed length Rear running gear: - Rear running gear with closed outer frame, chequer plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at rear - 2 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame Axles and tyres: - “PENDLE-AXLE”, all axles forced-steered by hydromechanics - Burst protection valve on axle compensation cylinder with automatic RESET feature - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position Dkodpfeh Hm Thsx Afmjk - Technical axle load: 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres / 3PMSF Accessories included: - Prepared for mounting attachable container positions for 1x 20ft or 1x 40ft container on the outer beams - 2'' king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with bracket - At the galvanized front connection strip: yellow-red air couplings - 4 wheel chocks - Remote steering from front and rear by cable remote control with push buttons, including track alignment monitoring for the axles - Hydraulic couplings from gooseneck to lowbed with multi-coupling system instead of screw couplings - Electro-hydraulic unit - White reflector tape according to EU regulations on the sides, extension, and red at the rear - 2 wooden blocks 500x250x200 mm - European reflector plates (red-yellow) at the rear of the trailer - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps for NLGI-2 standard grease - Load pressure gauge to determine axle loads, including load chart - On the gooseneck, plug-in ALU side and rear walls approx. 2,000 x 400 mm - The rear galvanized plug-in posts are removable (body length approx. 2,120 mm) - Separate air connection with air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps to bridge the mountings of the lowbed - Four extendable warning signs approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for the steering in addition to the cable remote, with indicator lights on receiver for track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beam for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Folding extensions, approx. 230 mm per side - Anti-slip sand layer painted on the loading platform - Dipper recess on the rear running gear closed at the front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (Zinc 85% - Alu 15%)

Durumu: yeni, azami yük ağırlığı: 50.400 kg, toplam ağırlık: 65.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You will find our complete range of vehicles with immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. GOOSENECK * Gooseneck in SNT design to optimize the loading platform length, approx. 3,700 mm long, rear taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with sockets * 3 kW electric-hydraulic power unit for controlling hydraulic functions (except hydraulic winches) * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized * One removable aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm solid hardwood floor above the gooseneck, over the kingpin with checker plate covering * 2" kingpin * Socket at the rear of the gooseneck for aluminum loading ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOADING AREA * Extendable loading area design, approx. 8,800 mm long, with rear taper approx. 500 mm x 10° * A recess in the loading platform and into the taper for accepting the excavator bucket arm, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st axle steering, all other axles hydro-mechanically forced-steered * 1st axle with electric-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF, twin mounting * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B – static test load: approx. 50,000 kg Dkjdpfxetx Nwnj Afmok * Continuous hardwood flooring approx. 50 mm thick on the loading area and interrupted between axles (increases friction coefficient) * 1 intermediate platform, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanised widenings, approx. 230 mm per side (without wooden planks) * Wheel recesses with 15 x 15 mm square climbing bars in front of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening inserts * Aluminum elements lockable on the extension tubes of the widenings * Widenable U-profiles for inserting the aluminum covers: - on the fixed section behind the gooseneck - on the intermediate platform - on the extendable loading area * Wheel recesses with 15 x 15 mm square climbing bars between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening inserts * Aluminum elements lockable on the extension tubes of the widenings * 1 pair of mechanical rear supports * Remote steering from both the front and rear via cable remote control, with axle single-track control, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm long, approx. 900 mm wide * Hydraulically foldable ramp tips * Ramps can be hydraulically shifted approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber flooring approx. 25 mm and steel deck approx. 5 mm as additional

Durumu: yeni, boş ağırlık: 13.500 kg, azami yük ağırlığı: 51.500 kg, toplam ağırlık: 69.500 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 r17.5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck in SNT design for optimization of loading area length, length approx. 3,700 mm Gooseneck rear with bevel approx. 1,000 mm x 10° Loading Area: Telescopic loading area, length approx. 8,800 mm, with rear incline approx. 500 mm x 10° Recess in the incline and extending into the loading area for accommodating the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected within the extendable beam and adjust to the respective loading area length Ramps: 1 pair of two-piece steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically adjusted individually approx. 235 mm outwards and 215 mm inwards Axles and Suspension: BPW axles and suspension, two fixed axles, two steering trailing axles Electromagnetic reverse lock activated via reverse gear and manually Air suspension with lifting and lowering valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Dsdpfsk Ahugox Afmjkk Load index: 143/141J (144/144F) Brake System: WABCO brake system, EBS-E according to EU regulations Lighting System: 24-volt lighting system, “ASPÖCK-NORDIK full LED” Metallization: Standard HRM metallization of the external frame Complete steel structure shot blasted, subsequently visible defined surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished Steel Structure: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified according to DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included accessories: Removable steel front wall, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 Round NATO socket on the front connection strip Cable for supplying the electro-hydraulic pump and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations (except for hydraulic winches) 1 spare wheel with mounting adapter External beams on the gooseneck with mounting holes for bolt-on lashing rings, first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included Mounting hole on the upper rear of the gooseneck external beam for a screw-on lashing ring 1 pair screw-in lashing rings Approx. 40 mm thick hardwood floor above gooseneck On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized On the gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodized 2" king pin Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 4 wheel chocks with holders Provision for aluminium approach ramps Mechanical landing gears with 2-speed gearbox and crank On the loading area, continuous hardwood floor approx. 50 mm thick, interrupted only between the axles Load area locking with conically welded positioning profiles every 250 mm including pre-tension plate Slotted holes at the front of the loading area for attachable and repositionable bridging plates 1 intermediate table with recessed loading area, approx. 300 mm wide, for the large cross-section sliding tube with sheet metal covering Front and rear with longe...

Durumu: yeni, boş ağırlık: 11.000 kg, azami yük ağırlığı: 38.500 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Platform: - Telescopic loading platform with rear chamfer approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and lower section widenings - Between the 1st and 2nd axle, a pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the bevel and extending into loading platform for excavator stick approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the platform (LC 10,000 daN) - 5 pairs of outward-folding lashing rings (LC 5,000 daN) - 2 pairs of outward-folding lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in excavator stick recess (LC 5,000 daN) - Cut-outs in outer frame of loading platform for securing straps (LC 2,000 daN) - Incl. 3-piece removable galvanized covers over wheel recesses – max. point load 3.5 t / each Two-Piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm hardwood covering - Ramp with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulically shiftable Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock activated via reverse gear and manually - Air suspension with lifting and lowering valve - Axle tools - Tyres 235/75 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Accessories Included: - Brackets for warning panels left and right on gooseneck and rear, incl. socket - One spare wheel - 2" kingpin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on galvanized connection rail at front - 4 wheel chocks - Galvanized, extendable widenings by approx. 230 mm per side - Galvanized folding supports under rear bevel of platform Dkedpfxeup U Hze Afmek - Bracket for beacon at rear of trailer - Cover plates to bridge the gap between ramps and platform - White reflective tape to EU regulations on sides and extension, red at the rear - Electro-hydraulic unit at rear, under loading platform - Control valves for ramps positioned on right side of trailer - European reflector signs (red-yellow) on rear of trailer - Four extendable warning panels by approx. 400 mm, approx. 423 x 423 mm, with a position light - Mount for beacon on warning panels - Removable ALU sideboards and tailgate on gooseneck approx. 2,440 x 400 mm - Rear galvanized removable stakes (body length approx. 2,560 mm) - 2 pairs WADER container locks in the loading platform for one 20ft or 30ft container - 3 pairs of stake pockets for plug-in stanchions 100 x 50 mm on the outer frame of the platform - One removable galvanized intermediate table with 1 pair WADER container locks - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the platform bevel - Anti-slip coated sand layer on tread plates of gooseneck and platform - 80 km/h speed limit stickers on the rear and on both sides - Load gauge for determining axle loads, including load diagram

Durumu: yeni, azami yük ağırlığı: 50.400 kg, toplam ağırlık: 65.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You will find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment features. Complete equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimized loading length, approximately 3,700 mm long, with rear bevel about 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic function control, excluding hydraulic winches * One pair of detachable ALU sideboards on the gooseneck, approx. 400 mm high, anodized finish * One detachable ALU rear wall on the gooseneck, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring on the gooseneck, checker plate flooring over the king pin * 2-inch king pin LOADING PLATFORM: * Extendable loading platform, approx. 8,800 mm long, with rear bevel about 500 mm x 10° * Recess in the loading platform extending into the rear bevel, for accommodating the excavator dipper arm, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor is handled via the standardized EBS interface according to ISO 11992. The tractor must be capable of receiving and displaying this data * TPMS tire pressure sensors installed in all wheels * BPW axles and suspension, first axle with steering function, all other axles hydro-mechanically forced steered * First axle with electro-magnetic reversing lock activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tool kit * Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B – static test load approx. 50,000 kg * 245/70 R 17.5 3PMSF twin tyres. Brand of our choice, load index 143/141J (146/146F) * Approx. 50 mm thick continuous hardwood flooring on the platform and between axles (increases coefficient of friction) * Securing of the platform with conically welded locking profiles approx. every 250 mm, including pre-tensioning plate * One intermediate table, approx. 300 mm wide, for the extension tube with large cross section * Intermediate table with stepped platform and retractable brackets for aluminum bridging elements * One pair of lashing rings on the front crossmember (LC 10,000 daN) * 8 pairs of recessed, outward-folding lashing rings in the outer frame of the platform (LC 10,000 daN) Dkjdoyhkrfjpfx Afmek * Extendable (galvanized) widening sections approx. 230 mm per side (without timber planks) * Wheel recesses with square climbing rungs, approx. 15 x 15 mm, located in front of the axles, openly extending to the gooseneck cross member, approx. 700 x 410 mm (W x D) * ALU covers for the wheel recesses, usable as bridging elements for the extension OR as widening boards (if extendable sections are fitted) * Wheel recesses with square climbing rungs approx. 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * One pair of mechanical rear supports * Steering from front and rear operable by cable remote control, with single-track monitoring of the axles HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-KG-HV-M One pair of two-part steel ramps, approx. 4,350 mm long and approx. 900 mm wide

Durumu: yeni, azami yük ağırlığı: 38.140 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Partial equipment list. Full specifications available on request. Gooseneck: - Gooseneck with approx. 45° chamfered front corners and a rear bevel of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - Between the 1st and 2nd axle, one pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable, galvanized wheel recess covers (approx. 670 mm wide - max. point load 5 t each) - 1 pair of recessed lashing rings at the front of the loading deck (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: Tyres 235/75 R17.5 3PMSF, brand at our discretion - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to the truck via the standardised EBS interface per ISO 11992 - For correct display, the truck must be capable of transmitting and displaying this data. Axles: - BPW axles and suspension, 2 fixed axles, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve. Axle tools Brake system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Electrical system: - Electrical system in accordance with EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel structure: Steel frame made of high-strength fine-grain steels. - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel structure is automatically blasted after welding using a turbine blasting system - Second blasting with corundum for optimal coating adhesion - HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure top corrosion protection - Final painting with two coats of 2K paint, solid colour in RAL 3002 Carmine Red, rear section metallised and painted in RAL 9010 Pure White - No metallic paint possible - Paint finish tested in salt spray test per ISO 9227-NSS - Sealing of cavities with special wax Djdjw Tpq Djpfx Afmokk Including the following accessories: - Mounts for warning signs on both sides at the gooseneck and at the rear, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch kingpin - Galvanized steel front bulkhead, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection panel - Galvanized folding supports under the loading area bevel - Hardwood impact protection on the rear wall from gooseneck to loading platform - 1 pair of recessed lashing rings along the central frame at the rear on the bevel (LC 10,000 daN) - Aluminium side walls and tailboard on the gooseneck

Durumu: yeni, azami yük ağırlığı: 51.780 kg, toplam ağırlık: 65.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. The following is an excerpt from the equipment list. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading area length, approx. 3,700 mm long, with rear ramped section approx. 1,000 mm x 10° * Suitable for tractor units: 4x2, 6x2, and 6x4 * Plug-in steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front terminal strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power pack for controlling hydraulic functions (excluding hydraulic winches) * Outer gooseneck beams with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the outer beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodised finish * On the gooseneck: 1 plug-in aluminum rear board, approx. 400 mm high, anodised finish * Approx. 40 mm thick hardwood flooring above the gooseneck * 2" kingpin * 1 transverse stake pocket rail fitted in the gooseneck deck in front of the ramped section, for plug-in stakes approx. 100 x 50 mm LOADING AREA: * Extendable loading area, approx. 8,800 mm long, with rear ramped section approx. 500 mm x 10° * Recessed well in the deck including the sloped section for excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st and 2nd axles fixed, 3rd and 4th axles steering * 3rd and 4th axles with electromagnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lift and lower valve * Mechanical landing legs with 2-speed gearbox and crank * Continuous hardwood flooring approx. 50 mm thick on deck and between axles (increases friction coefficient) * 1 intermediate table with recessed platform, approx. 300 mm wide, for large cross-section sliding tube with sheet metal covering * 1 pair of lashing rings on front cross-member (LC 10,000 daN) * 6 pairs of recessed lashing rings in the outer frame, foldable outward (LC 10,000 daN) * Additionally, 1 pair of external lashing rings on the front cross-member, oriented approx. 90° toward deck (LC 10,000 daN) * Extendable galvanized side extensions, approx. 230 mm per side (without timber boards) * 1 pair of fixed wheel recesses open up to the extension, approx. 700 x 410 mm (W x D), in deck in front of 1st axle * Between 2nd and 3rd axles: 1 pair of fixed wheel recesses, approx. 1,695 x 700 x 410 mm (L x W x D) * 1 pair mechanical rear supports * 245/70 R 17.5 3PMSF dual tires, brand of our choice HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-HB-HV-M * One pair of two-part steel ramps, approx. 4,350 mm long, 900 mm wide * Hardwood decking * Hydraulically folding ramp tips * Each ramp hydraulically adjustable approx. 235 mm outward and 215 mm inward * Hardwood decking on rear deck slope Dksdpeyhkrlofx Afmjk * Ramp with hardwood surface BRAKING SYSTEM: * WABCO EBS-E braking system in accordance with EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% al...