Brandalı açık yarı römork

DINKEL 3-Achs-Sattelanhänger, Pritsche+Plane, LBW

Durumu: kullanılmış, boş ağırlık: 11.950 kg, azami yük ağırlığı: 37.550 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2025, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R17.5, renk: gri, Üretim yılı: 2025, Donanım: ABS, For every used semi-trailer, you receive a current and comprehensive inspection and functionality report. Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings - 30 mm thick hardwood floor Two-piece steel ramps: - 1 pair of galvanized two-piece steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections, hydraulic lifting mechanism - Maximum load per pair: 30,000 kg Loading area: - Loading area with rear bevel approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings - 3 pairs of fold-out lashing rings - 1 pair of recessed lashing rings at the front of the loading area - Approx. 48 mm thick hardwood floor, checker plate covering above the axles Axles and tires: - BPW axles and suspension, two axles fixed, one axle self-steering - Air suspension with lifting/lowering valve - The self-steering axle is equipped with an electromechanical reverse lock, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" kingpin - One galvanized steel front wall Itodpfx Agsy Drdce Nof - Yellow-red air couplings at the galvanized connection strip in the front - 4 wheel chocks with holders - Recess at the rear of the gooseneck for ALU loading ramps - 3 height-adjustable aluminum planks - Galvanized folding supports under the loading area bevel - Holder for a beacon at the rear of the trailer - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized front wall with tensioning mechanism for the sliding curtain - Height adjustable by approx. 400 mm - "EDSCHA" brand roof, forward-sliding on ALU roof rail profiles, bolted with front and rear wall - 3 pairs of sliding stanchions in the loading area - The body is hydraulically extendable to the left and right at the rear by approx. 750 mm - Sliding roof with tiltable portal support - Sliding curtain with 700 mm reserve in length, equipped with tension belts spaced approx. 600 mm apart - Height of upper edge of body approx. 3,960 mm - Journeys with open sliding roof are not permitted and will result in damage to the tarpaulin - Cover plates to bridge the gap between ramps and loading area - Electro-hydraulic unit at the rear, beneath the loading area - On the gooseneck and on the ramps, left and right, each with a holder for warning signs, including socket - European reflective signs (red-yellow) at the rear of the trailer - 6 pairs of stanchion pockets for insertable stanchions 100 x 50 mm in the outer frame of the loading area - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading status - Grating floor covering in the bevel of the loading area C40/4 (point load 3.4 t on an area of 20 x 20 cm) - 1 stainless steel toolbox INOX 565 x 290 x 810 mm, right-hand side in driving direction between the axles - On the checker plates on the gooseneck and loading area, anti-slip sand coating painted on - BEKAMAX (Pico) centralized lubrication system with standard grease NLGI-2 - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm - Load gauge for determining axle loads, including load chart - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then the defined visible surfaces hot-metalized with ZINACOR 850 (zinc 85% - aluminum 15%)