Kullanılmış Fliegl Sığır Kamyonu satın al (307)

Durumu: yeni, toplam ağırlık: 41.000 kg, boş ağırlık: 9.800 kg, azami yük ağırlığı: 31.200 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: dc46d2e1cd272305b99fb3160, Further information Vehicle consists of: Chassis: Low-bed semi-trailer Steel welded construction, kingpin plate with replaceable 2-inch kingpin and two kingpin positions 24 t, 2-speed landing gear, operated from one side, with straight foot, without telescopic compensation Foldable rear support 2 wheel chocks with holders Hfedpfx Aaji Ri Hcscsn Side underrun protection made of aluminium Quarter-circle mudguards in front of and behind axle modules 1st pair of wheel recesses sunken into the low-bed loading area behind the gooseneck, bevelled for entry. Length at base approx. 1,600 mm, depth of recesses approx. 260 mm. Note! The frame is 260 mm higher than the wheel recess in the main beam area. 2nd pair of wheel recesses between axles A and B. Length at base approx. 350 mm, depth approx. 260 mm. Note! The frame is 260 mm higher than the wheel recess in the main beam area. If wheel loaders are to be transported and the total height needs to be checked, please provide the technical data sheet for the respective wheel loader types with precise dimensions (if total height is exceeded -> customer assumes risk, permit required); depending on ground clearance under the machines, inserts in the wheel recesses may be required on the customer's side. Wheel recess covers pull-out from the main frame, with wooden inlays. Extensions can be pulled out to 3,000 mm (not possible in rear slope area and not at the base of the wheel recesses) (track width of construction machines/vehicles to be transported must not exceed external frame width of 2,550 mm). Storage compartment for wooden planks on gooseneck, transverse at the front 70 mm wooden planks for widening to 3,000 mm Tie-down points on low-bed 2 pairs of ring lashing eyes, each 5 t, at the front on the gooseneck 11 pairs of lashing points (Zurrpilze) recessed into the top and side of external frame, each 10 t - 2x on gooseneck - 9x on low-bed deck (first eye 250 mm from the front, last max. 250 mm from the rear, distance between eyes not greater than 1,100 mm) 8 pairs of stanchion sockets recessed in the external frame, internal dimensions 70 x 40 mm, or alternatively 5 t ring lashing eyes recessed in the floor instead of sockets Axles + Suspension SAF drum braked axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Wheels and Tires 235 / 75 R 17.5 to manufacturer’s choice Steel twin wheels, factory silver Braking system 2-line air brake system Spring-loaded parking brake EBS, electronic braking system with EBS socket at front, no connection cable Attention: The trailer may only be towed by tractors that ensure full ABS functionality! 2 non-interchangeable coupling heads at front, without connecting pipe With lifting & lowering valve Axle load detection via EBS CAN bus signal, for indication on the truck’s cab display – truck must be pre-equipped accordingly, not truck-installed (not certified as a weighing system) Vehicle stability control system Electrics 24 volts, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front 2 white/red lane marker lights at rear 2 x 7-pin non-interchangeable sockets at front, without connection cable 1 x LED beacon with bracket, controlled via parking light (rotating beacon detachable) 2 pairs of warning boards, double-sided, LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel/checker plate covering Storage box integrated in inclined drive-over area to gooseneck - Then 70 mm softwoo

Durumu: yeni, toplam ağırlık: 50 kg, boş ağırlık: 14 kg, azami yük ağırlığı: 35 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: 5c7120ea17bcf92d3b69899da, Further information Chassis Low-bed Semi-Trailer Steel welded construction, fifth wheel plate with interchangeable 2" kingpin 24 t 2-speed landing gear, single-sided operation, with straight lower part, without compensating mechanism Foldable rear support 2x wheel chocks with holders Aluminum side underrun protection Quarter shell fenders in front of and behind the axle assembly With splash guards behind each axle 1x storage box, w=2,350 mm x l=730 mm x h=640 mm, bolted transversely at the front on the gooseneck floor, with 2 trays Extendable widenings up to 3,000 mm (not in rear chamfer area) (track width of the construction machines or vehicles to be transported must not exceed outer frame width of 2,550 mm) Storage compartment for timber planks on the gooseneck, front transverse 70 mm wooden planks for widening to 3,000 mm Excavator arm recess from the rear axles to the rear, approx. 500 mm wide and approx. 230 mm deep Tie-down rings, low loader 3 pairs of 10 t tie-down rings at the front gooseneck, 8 pairs of 10 t tie-down rings in the drop deck, 3 pairs of lashing rails in the drop deck lane area, 3 pairs of 10 t tie-down rings in the axle/rear area Axles & suspension SAF drum brake axles Axles/chassis laser alignment for reduced tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Secondary steering with radio remote control + automatic alignment (up to max. 20 km/h) Hfsdpoi Ri Hgsfx Aacen Note! The truck must be equipped with a 2-pole NATO socket with at least 2 x 35mm² for steering power supply. Power for the pump unit is supplied via NATO connection cable to the towing vehicle, without truck installation (steering must be used once a week). Air suspension Wheels and tires 235 / 75 R 17.5 as per manufacturer’s choice Steel twin wheels, factory silver Brake system 2-line compressed air braking system. Color-coded lines for easy service. Spring-loaded parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractors that ensure the proper functioning of the ABS! 2 non-interchangeable coupling heads at the front, without connecting lines With lift & lower valve, hold function in lowering mode + auto-reset function Axle load detection via EBS CAN bus signal, for display in the cab. Truck must be pre-equipped accordingly. No truck installation (not a calibrated scale) Vehicle Stability System Trailer Info Center for display of vehicle data such as axle loads (not a calibrated scale), mileage, and diagnostic/system messages. Electrical 24 Volt, multi-chamber lamps, side yellow LED lighting 2 white front position lights in LED 2 white/red lane marker lights at rear 2 x 7-pin, non-interchangeable sockets at the front, without connecting cable 1x additional LED work light at rear, switched via reverse light 1x LED beacon with bracket, operated via parking light (removable lamp) 2 pairs of illuminated warning signs, double LED, extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the lane area with 70 mm softwood floor, wheel arch area with steel/checker plate covering, drop deck left and right in the lane area can be hydraulically raised via truck PTO Rear chamfer with 70 mm softwood floor Drop deck length approx. 6,300 mm Sideboards 25 mm aluminum hollow profile, 400 mm high, front and side on gooseneck, plug-in type Access ramps Steel ramps, 2,800 mm long, 750 mm wide, side...

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 18 kg, boş ağırlık: 3 kg, azami yük ağırlığı: 14 kg, lastik boyutu: 445/45 r19,5, makine/araç numarası: 1eb6bdba4d54d87ab018b84c2, Further information Chassis Interchangeable Central-Axle Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Removable pair of guide rollers, front and rear 4 container locks with robust outriggers for interchangeable containers, 20-foot base, compatible with swap bodies 7.15 and 7.45 1 pair of gearbox support feet at the front, with straight lower part and single-sided operation on the right (FR) 2 wheel chocks with holder Aluminium side underrun protection Steel underrun protection Half-shell mudguards Splash flaps Central axle drawbar assembly Drawbar with certified 50 mm towing eye, forwarding version (not suitable for trucks with tail-lift; detailed inspection upon order required) Drawbar without length adjustment Axles & Suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Braking System 2-line compressed air braking system Colour-coded wiring for simplified servicing. Air reservoir: 208 litres Spring-loaded parking brake Duomatic coupling at the front, with connecting line to the tractor unit, connection on front left (FR) EBS, Electronic Braking System with EBS socket at the front, with connecting cable, connection on front right (FR) Note: The trailer may only be towed by towing vehicles which ensure the functionality of the ABS! With lift & lower valve, retaining function in both lift and lower positions Wheels and Tyres 445/45 R19.5, make at manufacturer's discretion Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear Hjdpfxsi Ri Itj Aacofn 2 x 7-pin polarity-protected connectors at the front, with connecting cable, connection on front right (FR) LED work lights on both sides (switched via reverse light) LED work light front-centred between the carrier beams, rear-facing, switched via reverse light Operating Instructions Special permit required if total train length exceeds 18,750 mm. Country-specific approval regulations must be observed. Country of registration / Plates Germany With Dekra inspection and report (according to §13 EC - FGV) 24/7 Service Hotline Prepared for single-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Paintwork Frame painted DB 7350 Nova Grey 10-year anti-corrosion warranty Note: Archive images!

Durumu: yeni, dingil konfigürasyonu: 3 dingil, toplam ağırlık: 24.000 kg, boş ağırlık: 10.280 kg, azami yük ağırlığı: 13.720 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: ee3256d63dd23b3ad1bdf9ab0, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Rear spray guards across the entire width Hjdpoi Ri I Njfx Aacjfn Quarter-circle mudguard in front of the 1st axle Excavator arm recess starting above rear axles and running to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t in the excavator arm recess, located on the side of the main frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer 1 storage box recessed in the kink of the floor with lid, W=720 mm / L=520 mm / D=170 mm 1st pair of wheel wells recessed after the frame drop in the low-bed running gear area, with ramped entry, length at the bottom approx. 1,600 mm, approx. 400 mm deep. Note! The main frame is 400 mm higher in this area than the wheel well. 2nd pair of wheel wells between the axles in the low-bed section, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The main frame is 300 mm higher in this area than the wheel well. Removable wheel well covers, insertable from main frame, with timber inserts. Distance from outside main frame beam to beam in wheel well area approx. 1,280 mm Extendable widenings to 3,000 mm, folding at the wheel well extensions (widening not at the rear chamfer and not at the bottom of the wheel wells) (Track width of machinery/vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for timber planks, centrally on or under the loading surface as per technical feasibility Timber planks 70 mm for widening to 3,000 mm Lashing points for low-bed trailer 1 pair of ring lashing eyes recessed at the front on the frame drop, each rated 5 t 8 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated 10 t 2 x front on frame drop 6 x in the low-bed first lashing eye 250 mm from front and last max. 250 mm from rear, spacing between lashing eyes no greater than 1,100 mm 5 pairs of ring lashing eyes recessed into the outer frame, each rated 5 t (convertible to stake pockets) Drawbar and turntable for trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser alignment to reduce tyre wear and fuel consumption Air suspension with independently controllable raise & lower valves at front and rear Wheels and tyres 235/75 R 17.5 Manufacturer’s choice Steel rims, twin-wheel arrangement, factory silver Braking system 2-line compressed air braking system Spring-actuated parking brake Trailer Info Center, displays vehicle data such as axle load (not calibrated) and odometer Axle load detection via EBS-CAN bus signal, display in cab (truck must be pre-equipped accordingly, no truck installation, not a calibrated scale) Vehicle stability system Duomatic coupling at front, with connecting line to tractor vehicle EBS (Electronic Braking System) with EBS connector at front, with connection cable Note: The trailer must only be towed by vehicles that guarantee the effectiveness of the ABS! Electrics 24 Volt, multi-chamber LED taillights with resistor, lateral amber LED lights, licence plate LED illumination (Note: with certain towing vehicles false diagnostics may occur even though functionality is guaranteed) 2 front position lights in LED 2 rear lane marking lights in white/red

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 18 kg, boş ağırlık: 5 kg, azami yük ağırlığı: 12 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: 2b58968e34fac93b429a256e9, Further information Chassis – Low-bed Trailer - Steel welded construction - Turntable with heavy-duty ball race, storage box recessed in turntable front section - Foldable rear support - Wheel chocks with holders - Aluminum side underrun protection - Full-width rear spray flap - Quarter shell mudguards in front of 1st axle Hfjdpfxji Ri Nxe Aacjn - Spare wheel carrier for 1 spare wheel, with attachment kit - Spare wheel, same brand and specification as base tires, steel rim - Plastic toolbox with insert shelf, dimensions: width=620 / height=360 / depth=440 mm, lockable with a padlock (lock not included) Tie-down Points Low-bed - 3 pairs of lashing points, each rated for 10 tons, integrated into the floor at the front - 6 pairs of lashing studs, inserted in the upper and side outer frame, each for 10 tons; 1 in the gooseneck area, remaining distributed with max spacing of 1200 mm; 1 at rear incline - 5 pairs of ring-type lashing eyes recessed into the outer frame, each rated for 5 tons (convertible to stake pockets) Trailer Drawbar/Turntable - Drawbar with tested 40 mm towing eye Axles & Suspension - SAF drum brake axles - Axles/chassis laser aligned to reduce tire wear and fuel consumption - Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tires - 235/75 R17.5 - Tire brand at manufacturer’s discretion - Steel twin-mounted rims, factory silver Braking System - 2-line air brake system - Spring-loaded parking brake - 2 reverse-polarity-proof coupling heads at the front, with connecting lines to the towing vehicle - ABS and ALB, with ABS plug at the front, connection cable, voltage converter for 12/24 volt operation Note: A 7-pin 12V socket on the tractor/hauler is required (required for electrics with voltage converter!) Warning: The trailer may only be towed by vehicles that guarantee the effectiveness of the ABS! Electrics - 24 volts, multi-chamber lighting, yellow LED side markers - 2 white/red track lights at the rear - 2 white position lights at the front - Additional LED work light at the rear, operated via reverse gear - 2 x 7-pin reverse-polarity-proof plugs at the front, with connecting cable - 1 x 7-pin agricultural plug - Voltage converter 12/24 volt (for electrics only, not for ABS/EBS) Floor - Steel floor in the front area, followed by 70 mm softwood floor - In the wheel arch area: steel / chequer plate covering - Rear incline with 70 mm softwood floor - Low-bed platform including rear incline: 8,200 mm Access Ramps - Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable - Wooden overlay - Spring-lift assisted Operating Instructions - A special permit is required for 10,000 kg axle load. The permit must be applied for separately in each federal state; approval for 20-ton GVW is at the discretion of the authorities – customer’s responsibility. Country of Registration / License Plates - Registration country: Germany - With Dekra inspection and expert's report (according to §13 EC-FGV) - 24/7 service hotline - Prepared for two-line license plate holder - Reflective contour marking as per ECE R 048, white on the sides and red at the rear Paintwork - Frame: DB 7350 Novagrau - 10-year anti-perforation warranty - Drawbar: galvanized or painted black, depending on manufacturer's choice - Ramps: hot-dip galvanized Note: Archive images!

Durumu: yeni, toplam ağırlık: 28.000 kg, boş ağırlık: 5.800 kg, azami yük ağırlığı: 22.200 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235/75 r17,5, makine/araç numarası: 1acf251a278ec5cde4067a7b1, Further information Chassis Semi-Trailer Forwarder Fine-grain steel welded construction, fifth wheel plate with replaceable 2-inch kingpin Outer frame slightly inclined, new version with load-lock profile for lashing straps 24 t, 2-speed landing gear, operated from one side, straight base, without compensating mechanism Free landing gear corner dimension or rear swing clearance approx. 1920 mm 2 wheel chocks with holders Side underrun protection aluminium Rear underrun protection steel Quarter mudguards in front of and behind each axle 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 1 plastic toolbox, with shelf, width=620 / height=360 / depth=440 mm, lockable with padlock (padlock not included) Axles & Suspension Drum brake axles, as per manufacturer’s choice Axles/chassis laser-measured to reduce tyre wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, color-coded line routing for easier servicing Spring-applied parking brake Duomatic coupling front, without connecting hose EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that can guarantee the effectiveness of the ABS! With lift & lower valve Vehicle stability system Wheels and tyres 235/75 R17.5, brand at manufacturer’s choice Steel rims, factory silver Electrics 24 volt, multi-chamber tail lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 15-pin socket at the front, without connection cable Floor Approx. 30 mm thick phenolic resin plywood for high point load capacity, suitable for forklift axle loads up to max. 5,600 kg Front panel / corner posts front 25 mm aluminium hollow section, approx. 1,350 mm high, corner posts steel in volume version Country of registration / plates Germany With DEKRA inspection and certificate (according to §13 EC-FGV) 24/7 Service Hotline Prepared for single-line license plate holder Conspicuity marking with reflective tape in accordance with ECE R 048, white on the sides and red at the rear Paint Frame hot-dip galvanized including passivation, 15-year anti-perforation warranty Hedpfxekv Uvzj Aacsfn Front wall aluminium Attention! Archive images shown!

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 11.800 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: ebf3f771e96394cd89e56bbb7, Further Information Chassis Central Axle Trailer Fine-grained steel welded construction 6 pairs of lashing eyes bolted to the exterior floor/frame, each rated at 5t 2 additional pairs of lashing eyes bolted to the floor in the corners, each rated at 5t Front support leg, gearbox type Foldable rear support 2 wheel chocks with holders Steel underrun protection Full-width rear mud flaps Quarter mudguards 1 plastic toolbox with shelf, dimensions b=620/h=360/d=440 mm, lockable with a padlock (padlock not included) Drawbar Central Axle Trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles & Suspension Drum brake axles as per manufacturer's specification Axle/chassis laser alignment for reduced tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation (balancing rocker) Wheels and Tyres 235 / 75 R 17.5 as per manufacturer's specification Factory silver steel rims Brake System 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at front with connecting lines to the tractor ABS and ALB, with ABS socket at the front and connecting cable Electrics 24 Volts, multi-chamber lights, side yellow LED lighting 2 white position lights at the front Hjdpfxsi Rixro Aacjfn 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable sockets at the front, with connecting cable Floor Steel chequered plate floor for high point load capacity Note: Slight floor undulation due to welding distortion possible! Platform length approx. 5,200 mm Rear taper approx. 900 mm Front wall / corner posts 25 mm aluminium hollow profile, 400 mm high Side walls 25 mm aluminium hollow profile, 400 mm high, foldable and removable Rear wall / rear corner posts 1 pair steel posts fixed to the frame with holders to secure loading ramps, clear entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with hand grip on ramps Surfaced with 3 serrated steel tracks Gas strut support for single person operation Registration Country/ Plates Registration country: Germany 24/7 service hotline Prepared for single-line licence plate holder Contour marking with reflective tape as per ECE R 048, white at the sides and red at the rear Paintwork Frame hot-dip galvanised including passivation 15-year warranty against rust-through Front wall aluminium Side wall aluminium anodised Loading ramps hot-dip galvanised Note: These are archive images.

Durumu: yeni, dingil konfigürasyonu: 3 dingil, toplam ağırlık: 24 kg, boş ağırlık: 3 kg, azami yük ağırlığı: 20 kg, lastik boyutu: 385/55 r22,5, makine/araç numarası: c3dd8c834afed73501f8074af, Further Information Chassis Swap Drawbar Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with robust supports on 20-foot base for swap bodies 7.15 and 7.45 m Turntable with heavy-duty ball bearing slewing ring 2 wheel chocks with holder Side underrun protection aluminium Rear underrun protection steel Half-shell mudguards front and rear 2 stainless steel toolboxes, b=600/h=400/t=500 mm, with polished door, lockable 1 pair of warning signs, double, LED illuminated, extendable to 3,000 mm at the rear, rear only 1 wiring provision for retrofitting customer-side warning signs at the front Drawbar equipment for turntable trailer Drawbar with certified 40 mm towing eye Drawbar mechanically adjustable in length by 6 x 100 mm increments and lockable (drawbar length approx. 1,900–2,500 mm) Drawbar height adjustment via spring Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axles/chassis laser measured – reduces tyre wear and fuel consumption Air suspension with lift & lower valve Wheels and Tyres 385/55 R22.5 Manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle EBS – electronic braking system with EBS connector at the front, with connecting cable Hjdpfx Aaoi Riylocjfn Note: The trailer may only be towed by vehicles that ensure correct ABS operation! Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 front white position lights 2 rear white/red lane marker lights Removable rotating beacon 1 additional LED work light at rear, switched via reversing light 2 LED work lights on each side (1 left, 1 right), switched via reversing light 1 x 15-pin connector at the front, with connection cable Registration/Country Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC – FGV) 24/7 service hotline Prepared for single-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Paintwork Frame hot-dip galvanized including passivation – 15-year warranty against rust-through Drawbar KTL black

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 11 kg, boş ağırlık: 3 kg, azami yük ağırlığı: 8 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: e763c8c2bb3370bd2342236a4, Further information Chassis Central Axle Tipping Trailer Steel welded construction, continuous tipping shaft at the rear with 80 mm ball tip bearing Gearbox support leg at the front 2 wheel chocks with holders Steel underrun protection Lockable storage compartment for loading ramps underneath the platform Central axle trailer drawbar Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles + Suspension Hodei Rizbepfx Aacofn Euro-axles at our discretion, with tapered roller bearings and S-cam brakes Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalisation (rocker equaliser) Wheels and Tyres 235/75 R 17.5 manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Colour-coded line routing for easy servicing Hand spindle parking brake Integral air reservoir Without ABS, but with mechanical ALB. Maximum permissible speed: 60 km/h 2 unmistakable coupling heads at the front with connecting lines to the tractor unit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red marker lights at the rear 1 x 7-pin 12 Volt plug at the front, with connecting cable approx. 60 cm extended Hydraulics Three-way tipper, hydraulic multi-piston press with stroke limiter and safety cable Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK connector NW 10/3, incl. connection hose Operation hydraulically via PTO from the truck Tipper Body Robust tipper body with 4 mm steel sheet floor, steel drop side body, continuous side walls, fold-down and pivot-mounted with central locking at the bottom. Removable corner posts at the rear. Rear wall fold-down and pivot-mounted with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2,420 mm 5 pairs of lashing eyes in the floor, each 5 t Operating Instructions The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while complying with permissible axle, support, and kingpin loads. (Poor driving and trailing performance possible due to incorrect load distribution) Country of Registration / Licence Plates Country of registration: Germany with Dekra approval and certificate for max. 60 km/h registration, towing vehicle agricultural or forestry tractor (country of registration Switzerland max. 40 km/h possible) Prepared for single-line license plate holder Without contour marking / reflective stripes according to ECE R 048 Paintwork Frame hot-dip galvanised incl. passivation, 15-year warranty against rust-through Side walls/body RAL 3002 Carmine Red Note! If the body is galvanised, it will not be painted! Note! Body interior only primed! Wide tyres possible at extra cost. 355 / 60 R 18, then loading height approx. 980 mm Attention: Archive images!

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 13.400 kg, boş ağırlık: 2.100 kg, azami yük ağırlığı: 11.300 kg, lastik boyutu: 275/70 r 22,5, makine/araç numarası: 8fbda13da8c595f64678f0f82, Further Information Chassis Central Axle Trailer Fine-grain steel welded construction Fifth wheel coupling, brand at our discretion, suitable for 2 king pins, with ball-bearing turntable, stop max. 20° Support at drawbar and at the front of the dolly Wheel chocks with holder Steel underrun protection Half-shell mudguards Central axle trailer coupling system CLG under-mount drawbar with approved 50 mm towing eyes for connection to dolly and truck, including drawbar lock on the truck! Axles + Suspension BPW disc brake axles Air suspension for Swap Train version, standard fifth wheel height lowered approx. 1100 mm, raised approx. 1280 mm, coupling height approx. 1140 mm, Braking System 2-line compressed air braking system, color-coded piping for easy service. Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to the truck 2 fail-safe coupling heads with spiral-flex connection lines to the trailer EBS, electronic braking system with EBS plug at the front, with connection cable, EBS spiral-flex connection lines to the trailer Attention: The trailer must only be towed by vehicles that ensure the effectiveness of the ABS! with raising & lowering, ECAS, via truck controls, ECAS CAN 2 bus required in the truck. Without ECAS CAN 2 bus in the truck, additional control unit in the truck required (not included): Electrics with pre-wired cable and a distribution box. Operation via 15-pin socket pins 11 and 15 or for 2 x 7-pin sockets pins 7 and 5. Note! This version must still be technically approved in conjunction with the trailer. Dolly and trailer can presumably only be raised and lowered together; if this is not technically feasible, operation is via WABCO eTASC with hold function in the lowered position + auto-reset function (no power from the truck required). Additional operation on vehicle via WABCO eTASC + hold function in the lowered position + auto-reset function (no power from truck required) Vehicle - Driving Stability System ECAS only possible in conjunction with WABCO EBS. Axle load detection via EBS CAN bus signal for display in the driver’s cab (truck must be prepared accordingly, no truck installation/no calibrated scale) Brake release function from the truck (via switch) on pin 14 and additionally via switch on the vehicle next to raise & lower valve, for releasing the brake when coupled, EBS power supply must be ensured! With CAN router Wheels and Tires 275/70 R 22.5, brand at manufacturer’s discretion Steel rims, factory silver Electrics 24 volt, multi-chamber lights, side-mounted yellow LED lighting Side-mounted yellow LEDs linked to turn signals, flashing side markers 2 white LED position lights at the front 2 white/red lane-marking lights at the rear 2 x 7-pin fail-safe connectors at front, with connection cable, 2 x 7-pin fail-safe connectors with spiral-flex connection lines to the trailer Cable + plug/socket for reversing camera system, depending on vehicle type Operating Instructions Note! Observe the Long Truck Regulation! Please observe currently approved route network! Hfedpei Rizxjfx Aacjn Towing vehicle must be brought to Triptis factory for approx. 1 week for drawbar adaptation! Please observe CLG recommendations per attachment Mandatory before order acceptance: Submission of all relevant dimensions as per Fliegl CLG form (see attachment) The coupling height of the planned trailer must be known Fliegl Fahrzeugbau assumes no liability for defects in dimensional accuracy and drivability

Durumu: yeni, dingil konfigürasyonu: 3 aks, toplam ağırlık: 24.000 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: 408ba9a39bbb8087056d6e563, Further information Chassis Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear splash guard Semi-shell mudguards on 1st and 2nd axles with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess over the rear axles, running to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated 5 t each in the excavator arm recess at the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear incline 1 plastic toolbox, with insert shelf, w=620/h=360/d=440 mm, lockable with padlock (lock not included) 1 storage box recessed in the gooseneck in the floor with lid, W=720 mm/L=520 mm/D=170 mm Extendable width to 3,000 mm (not in the rear incline) (track width of machines or vehicles to be transported must not exceed outer frame width of 2,550 mm) Hsdsi Ri Daspfx Aacjfn Timber beams 70 mm for extension to 3,000 mm Storage compartment for timber beams under loading area Lashing rings lowbed (40 lashing points) 1 pair of lashing rings on gooseneck, each 5t 9 pairs of lashing studs, integrated in the top and side of outer frame, each 10t 2 x on gooseneck in front 7 x in the lowbed area 6 pairs of lashing holes in the outer frame of the lowbed area, 5 t each (for tie-down straps) 3 additional pairs of folding lashing rings, each 10 t 1 x inside next to main frame at start of lowbed 1 x on gooseneck (protrudes) 1 x recessed in the floor behind the last axle Trailer drawbar assembly Drawbar with tested 50 mm towing eye, towing eye inclined at 8°, D-value minimum 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 as selected by manufacturer Steel twin wheels, factory silver Brake system 2-line air brake system Spring-loaded parking brake 2 anti-mismatch coupling heads at front, with connection lines to truck ABS and ALB, with ABS plug at front, with connection cable Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at front 2 white/red marker lights at rear 2 x 7-pin anti-mismatch plugs at front, with connection cable 1 LED rotating beacon with holder, controlled via parking light (beacon detachable) 2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel/aluminium chequer plate covering followed by 70 mm softwood floor, with steel/aluminium chequer plate over wheel wells Rear incline with 70 mm softwood floor Access ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable with timber surfacing Hydraulic, powered via tractor PTO with flow restrictor, controlled laterally front left Hydraulic connection with SVK plug NW 10/3, including connecting hose Approval country / Plates Approval country: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective tape as per ECE R 048, side white and rear red Warning sign according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation, 15 years corrosion perforation warranty Drawbar galvanized or black, as per manufacturer’s choice Access ramps hot-dip galvanized Note: Images are for illustrative purposes (archive images)!

Durumu: kullanılmış, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 18.000 kg, boş ağırlık: 2.872 kg, azami yük ağırlığı: 15.128 kg, ilk tescil: 11/2019, lastik boyutu: 385/65 r22,5, Üretim yılı: 2019, makine/araç numarası: 3ca51192c90a3f38a59d77748, Further information: Hfedpfx Aaji Ri Dzocen Fine-grain steel welded construction, front stop, longitudinally adjustable and foldable, pair of guide rollers removable, front and rear, Swap Guard – swap body guiding system, placed in front of and behind each container locking device, 4 container locks with reinforced outriggers on a 20-foot base for swap bodies 7.15 and 7.45, turntable with heavy-duty ball bearing slewing ring, chocks with brackets, aluminium side underrun protection, side underrun moved inward for optimal clearance to swap body supports, steel rear underrun protection, rear underrun shortened for optimal clearance to swap body supports, lights installed in protected position, quarter-shell mudguards at the front and half-shell mudguards at the rear, without impact protection, spare wheel carrier in basket design, plastic toolbox. Drawbar (L = 2,200 mm) with certified 40 mm towing eye, drawbar length, drawbar height adjustable via spring. SAF disc brake axles with 430 mm disc diameter, axles/chassis laser-measured to reduce tire wear and fuel consumption, air suspension. 2-line compressed air brake system, colour-coded line routing for easy maintenance, air reservoir 208 litres, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front with connection lines to the truck, EBS (electronic braking system) with EBS connector at the front and connection cable. Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS!) With raise & lower valve, hold function in both raised/lowered positions, brake release function via button on the vehicle next to the H & S valve for releasing the brake when coupled. EBS power supply must be ensured! 24 volt, multi-chamber lights, side yellow LED marker lights, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 1 x 15-pin plug at the front with connection cable, additional LED work light at the rear, switched via reverse light, LED work light at the front centre between the beams, facing rearwards, switched via reverse light. Country of registration: Germany, with Dekra inspection and report (according to §13 EC-FGV), prepared for single-row license plate holder, warning plate according to ECE-70, ADR warning plate at the rear, foldable, contour marking with reflective strips according to ECE R 048, white on the side and red at the rear.

Durumu: yeni, toplam ağırlık: 35.000 kg, boş ağırlık: 5.500 kg, azami yük ağırlığı: 29.500 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22,5², makine/araç numarası: 71cc13750cef13b72f7a55abe, Further Information Chassis Semi-Tipper Fine-grain steel welded construction with lightweight design, fifth wheel plate with replaceable 2" kingpin Curved front wall, patented 24t two-speed landing gear, single-sided operation, with straight lower section, without push-rod compensation 2 wheel chocks with bracket Underride protection, foldable Half-shell mudguards Integrated mudguard holder with stone-repellent surface Anti-spray mud flaps on rearmost axle only 1 tarp pole with bracket 2 towing hooks at rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Axles in off-road version Air suspension 1st axle automatic lift axle, including forced lowering and start assist, operated by pressing brake three times (start assist functions up to 30% axle overload and up to max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against corrosion Brake System 2-line compressed air brake system, color-coded pipelines for easy service Spring-loaded parking brake 2 anti-mix coupling heads at front, without connection line EBS, Electronic Brake System with EBS socket at front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of ABS! With raise and lower valve Vehicle stability control system Wheels and Tyres 385/65 R22.5, make per manufacturer’s choice Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED marker lights 2 white position lights at front 2 white/red contour marking lights at rear 2 x 7-pin anti-mix sockets at front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chromed, with HD coupling nut, fixed part, NW 48 mm (without hose connection) Operated hydraulically via vehicle PTO Body Aluminium box body made from high-quality, wear-resistant material; front wall 5 mm thick, external side walls from 30 mm hollow section profiles, expertly welded, with spill-repellent top rail profile. Internal ladder on front wall (not with Cramaro option). Shovel and broom holder outside on front wall. Greenline – conical and aerodynamic body shape Membrane – tailgate Tailgate pendulum-mounted with double hinge and split 1/2 to 1/2 with top swing arm, with one grain slide per door. Tailgate with rubber seal. Note: Heat-resistant up to max. 170°C! Floor throughout 6 mm thick Standing platform with access steps, connector plate for air/electrics and brake with ample space for ease of use Roll tarp to be stowed on right side (FR-right) with central locking on left side (FR-left) Operating Notes For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent material damage and corrosion. The stated gross weight is technically possible; depending on the load, the gross weight may not be achievable within the allowable axle/kingpin/load limits. (Poor driving and trailing behavior may result from incorrect load distribution) Country of Registration / Signs Germany Hfjdpfx Aaoi Ri Efocsn Approval according to EC 2007/46 24/7 Service Hotline Prepared for single-line license plate holder Conspicuity markings with reflective tape according to ECE R 048, white side and red rear Paintwork Frame DB 7350 Novagr

Durumu: yeni, toplam ağırlık: 21 kg, boş ağırlık: 6 kg, azami yük ağırlığı: 14 kg, dingil konfigürasyonu: 1 dingil, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: df0bcd99c5751964e020b1055, Further Information Chassis Low-bed Semi-Trailer Steel welded construction, fifth wheel plate with replaceable 2" king pin, low-bed sloping from wheel area to gooseneck with approx. 210 mm loading height, rear sloped to wheel area, aluminum ramp mounting rail across the entire rear width Wheel chocks with holders Side underrun protection in aluminum Hfjdpfsi Ri Hkox Aacen Wheel covers with removable galvanized steel sheeting 1 towing eye at rear, 10 t Spare wheel with holder on front wall/external front toolbox Steel toolbox on front gooseneck crosswise, approx. L = 2400 mm, W = 400 mm, H = 600 mm, lockable Electric cable winch, 24 V, pulling force 8165 kg, mounted in front on gooseneck behind toolbox, standing on load platform, operated via remote control, cable length 35 m x approx. 10 mm, with roller fairlead and 2 removable guide rollers on gooseneck and rear ramp. NATO socket on terminal plate 1 pair of wheel recesses approx. 700 mm starting from start of gooseneck recessed into the floor, open outward. Note: Main frame projects approx. 145 mm 4 pairs of insert positions for wheel stoppers (Fliegl standard), without wheel stoppers for parking the semi-trailer approx. 100 mm high and approx. 100 mm long Removable wheel stoppers When transporting tractors, an approx. 50 mm spacer in the front wheel recesses, size for wheel recess approx. 50 mm high, approx. 1200 mm long, approx. 500 mm wide Lashing points low-loader 2 pairs of 2.5 t lashing eyes on gooseneck 7 pairs of lashing mushrooms recessed at the top and side of outer frame each 10 t 4 pairs of 10 t lashing eyes recessed on the top of the main frame longitudinal beams 1 screwable lashing eye with 6.7 t (JDT) load at rear center in ramp storage compartment 1 additional folding lashing eye at front of low-bed, each 10 t Axle + suspension SAF drum brake axle, Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake 2 swap-proof coupling heads at front, without connecting hose EBS, electronic braking system with EBS socket at front, without connection cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of ABS! Electric 24 Volt, multi-chamber LED lights with resistor, side yellow LED lighting, license plate lighting in LED, (Note: With certain towing vehicles incorrect diagnostics can occur, although functionality is provided) 2 front white position lights in LED 2 rear white/red lane marker lights in LED 2 x 7-pin and 1 x 15-pin swap-proof sockets at front, without connection cable LED beacon with bracket, switched via sidelights (lamp removable) Additional LED work lamp at rear, switched via reversing light Floor Gooseneck covered with steel / checker plate Low-bed area steel-perforated plate, in wheel recess area steel / checker plate and in wheel housing area removable sheet covering Rear ramp with steel-perforated plate Side walls Aluminum, 400 mm high, side-mounted on gooseneck, removable, approx. 2500 mm long Rear wall aluminum, 400 mm high, on gooseneck, removable Loading ramps Pair of aluminum drive-on ramps, load capacity max. 12,000 kg per pair, approx. 3400 mm long and 320 mm wide, ramp storage 1 x between the rear longitudinal beams Operating instructions Approval / plates Approval country: Germany prepared for single-line license plate holder Contour marking with reflective strips in

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 14 kg, boş ağırlık: 3 kg, azami yük ağırlığı: 11 kg, lastik boyutu: 235/75 r17,5, makine/araç numarası: 207ad28f83705ed0d38a4f174, Further information Chassis Swap Central Axle Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with robust outriggers for 20-foot swap bodies, suitable for swap bodies 7.15 and 7.45 rear-flush (for 7.15 swap bodies, not rear-flush; forklift pockets/frame protrudes) Telescopic support leg at the front 1 pair of gearbox support feet at the front, with straight lower part and single-sided operation on the right (FR) Wheel chocks with holder Aluminium side underrun protection Steel rear underrun guard Half-shell mudguards Mounting for truck-mounted forklift at the rear, incl. 2 fork insertion pockets, 2 extendable support tubes, bracket for chain securing with locking pin. Rear underrun guard with light unit can be folded away. Includes 2 loose rubber pads to protect the rear panel; we recommend counterweight! Note: Partially low ground clearance with forklift, poor trailing behaviour possible, no guarantee! (Forklift self-weight up to max. 1,500 kg for trailers.) (With proximity switch for forklift control in conjunction with lift axle) The forklift mounting shifts the axles rearwards, pay attention to load distribution when driving without a forklift. Customer risk! (For swap body trailers, driving with forklift is only permitted in conjunction with a swap body.) Forklift mount adapted as per AU 203670 for 7.45m swap bodies Counterweight at the front between the frames, approx. 300 kg, if required, exact check still pending Drawbar equipment for central axle trailers Drawbar with approved 50 mm towing eye, forwarding edition (not suitable for trucks with tail lift, exact check still required when ordering) Undercoupler drawbar Drawbar without length adjustment Axles + Suspension SAF drum brake axles as per manufacturer's choice Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, colour-coded line routing for easier service Spring-loaded parking brake Duomatic connection at front, with connecting line to the tractor, on the left (FR) Duomatic connection at front, with connecting line to the tractor, connection on the right (FR) EBS, Electronic Braking System with EBS plug at the front, with connection cable, on the left (FR) Attention: The trailer may only be towed by towing vehicles that ensure the functionality of the ABS! With lift & lower valve, holding function in each lift/lower position Vehicle - Drive stability system Wheels and Tyres 235/75 R17.5, brand as per manufacturer's choice Steel twin wheels, factory silver Electrics 24 Volt, 4 x 3-chamber tail lamps + 1 round reversing lamp + 1 round rear fog lamp, side yellow LED lighting, lights mounted protected! 2 white position lamps at the front 2 white/red lane marking lamps at the rear 1 x 15-pin connector at the front, with connecting cable, on the left (FR) 2 x 7-pin sockets at the rear left (FR) for truck-mounted forklift 1 x 15-pin socket at the rear left (FR) for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reverse light) Additional LED work light at rear, switched via reverse light Approval / Plates Germany Hedsi Ri Iajpfx Aacefn With Dekra inspection and certificate (as per §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour markings with reflective tape as per ECE R 048, white on the sides and red at the rear Painting Frame DB

Durumu: yeni, toplam ağırlık: 32.000 kg, boş ağırlık: 4.200 kg, azami yük ağırlığı: 27.800 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 385/65 r22.5, makine/araç numarası: 83732a53562459145277be051, Further Information Chassis Semi-Trailer Tipper Fine-grain steel welded construction, lightweight design, fifth wheel plate with interchangeable 2" kingpin Curved front wall, patented 24 t. 2-speed landing gear, single-sided operation, with straight base, without compensating mechanism 2 wheel chocks with holder Folding underrun protection Half-shell mudguards Integrated mudguard bracket, stone-repellent surface With anti-spray mudflap only on the last axle 1 tarpaulin bar with holder 2 towing hooks at the rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reduces tire wear and fuel consumption Axles in off-road design, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, operated by braking three times (starting aid function active up to 30% axle overload and up to a max speed of 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system. Color-coded line routing for easy maintenance. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer must only be towed by towing vehicles which ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability system Automatic tipper lowering with shut-off valve Wheels and Tyres 385/65 R22.5, manufacturer as per supplier's choice Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operated hydraulically via truck PTO Body Aluminum box body made of high-quality, wear-resistant rigid front wall 5 mm thick, with external side walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. With step at front wall (not in combination with Cramaro). Shovel and broom holder outside on the front wall. Hfjdpfx Aaji Ri Nbocon Greenline – conical and aerodynamic body shape Membrane tailgate Rear wall as pendulum flap with double hinge, exterior mounted with double hook locking. Rear wall with rubber seal. Note: Heat resistant up to max. 170°C! Continuous 6 mm thick floor Standing platform with access, connection plate for air/electric and brake with ample free space for best possible operability. Roll tarp, can be folded on the right side, central lock on left side Operating instructions For transports of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent damage and corrosion by material. The specified total weight is technically possible. Depending on the cargo, the total weight may not be achievable while complying with permissible axle/support/kingpin loads. (Poor driving and tracking due to incorrect load distribution possible) Registration Country/Plates Germany Approval according to EC 2007/46 24/7 Service Hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Paint Frame DB 7350 Novagrau 10 Y

Durumu: yeni, toplam ağırlık: 32.000 kg, boş ağırlık: 4.500 kg, azami yük ağırlığı: 27.500 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 385/65 r22.5, makine/araç numarası: 8b1f4087611d72661dc0b3869, Further Information Chassis Semi-Trailer Tipper Fine-grain steel welded construction, in basic lightweight design, fifth wheel plate with replaceable 2” kingpin Curved front panel, patented 24 t 2-speed landing gear, single-sided operation, with straight base, without load compensation Wheel chocks with holders Foldable underrun protection Half-shell mudguards Tarp pole with bracket Tow hook at the rear Axles & Suspension SAF disc brake axles Axle/chassis laser alignment to reduce tire wear and fuel consumption Axles in off-road version Air suspension 1st axle with automatic lift axle, including forced lowering and starting aid, actuated by 3x braking (Starting aid remains functional up to a 30% axle overload and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10 years warranty against corrosion Braking System 2-line compressed air braking system with color-coded line routing for easy servicing Spring-loaded parking brake 2 error-proof coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure the ABS functions correctly! with raise & lower valve Vehicle - Driving Stability System Wheels and Tires 385/65 R22.5 Steel rims, factory silver Electrics Hedpfx Aaoi Ri Nfjcefn 24 Volt, multi-chamber lights, yellow LED side lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pole error-proof sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via PTO on the truck Body Steel round body in Stone Master design made from highly wear-resistant HB 400/450 steel. Slanted front wall with external hydraulic units and ladder on the front wall. Greenline – conical and aerodynamic body shape Shovel and broom holder on the exterior of the front wall. Membrane Rear Wall Rear wall as pendulum flap with double joint hinge, external with double hook locking. 2 clamping screws with toggle locks at the lower sides. Continuous 4 mm thick sidewalls, floor 4/5 mm thick, wear- and weight-optimized construction Standing platform with ladder, connector plate for air/electric and brakes with large free space for optimal operation Roll tarp stows on passenger side (FR-right), central locking on driver’s side (FR-left) Operating Instructions For transports of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent damage and rusting from the materials transported. The specified total weight is technically possible; depending on the cargo, the maximum total weight under consideration of legal axle, support, and saddle loads may not be achievable. (Improper weight distribution may lead to poor driving and tracking behavior.) Country of Registration / Plates Germany Approval according to EC 2007/46 Body stability according to EN 12642 24/7 Service Hotline Prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame: DB 7350 Novagrau, 10 years warranty against corrosion Landing legs: black coated Body: RAL 7035 light grey Fliegl branding "StoneMaster" on sides and rear Roll tarp in desired RAL color, single color Available in thermally insulated version: Cover BA

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 18.000 kg, boş ağırlık: 3.055 kg, azami yük ağırlığı: 14.945 kg, lastik boyutu: 235/75 r17,5, makine/araç numarası: 06017a31026c05fc8f6ccf5ae, Further information Chassis: Swappable rotating dolly Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with robust outriggers on 20-ft base for swap bodies 7.15 and 7.45 Rotating dolly with heavy-duty ball bearing turntable 2 wheel chocks with holders Aluminium side underrun protection Steel rear underrun protection Quarter mudguards at the front and half-mudguards at the rear Drawbar device for dolly trailers Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Laser-measured axles/chassis for reduced tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, color-coded line routing for easy servicing Spring-loaded parking brake 2 foolproof coupling heads at the front, with connecting lines to the motor vehicle EBS, Electronic Braking System with EBS plug in front with connecting cable Note: The trailer may only be towed by towing vehicles that can ensure effective ABS operation! With raise & lower valve, holding function in both lower and raised positions Wheels and tires 235/75 R17.5 tires, brand at manufacturer's discretion Steel twin wheels, factory silver Electrics 24 volt, multi-chamber LED lights with resistor, yellow LED side marker lights, LED number plate light (Note: Certain towing vehicles may trigger false diagnostics despite proper functioning) 2 white front position lights in LED Hsdpfx Aasi Ri Rcjcofn 2 white/red lane marker lights at rear in LED 1 x 15-pin plug at front with connecting cable Additional LED work light at the rear, switched via reverse light Approval / Plates Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame: DB 7350 Novagrau Note: Archive images!

Durumu: yeni, dingil konfigürasyonu: 3 dingil, boş ağırlık: 24.000 kg, azami yük ağırlığı: 7.550 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: ede0610378cbe39cc4883251d, Further Information Chassis Low Loader Trailer Steel welded construction 1st pair of wheel recesses integrated into the steel platform in the driving aisle area, tapered for entry, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! The frame is 400 mm higher than the wheel recess in the main beam area. If machines are to be transported and the total height needs to be checked, we kindly request the technical datasheet of the machine types with exact specifications (if total height is exceeded -> customer risk, approval required). Depending on ground clearance under the machines, inserts in the wheel recesses may be required by the customer. Turntable with heavy-duty ball bearing slewing ring, toolbox integrated into the turntable front section Hfedpsi Ri Ryefx Aacen Rear support foldable 2 wheel chocks with holders Side underrun protection in aluminium Rear mudflaps across the full width Extendable widening to 3,000 mm (not in rear bevel area) (The track width of the machines or vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for wooden planks in the centre of the loading area 70 mm wooden planks for widening to 3,000 mm Lashing points for low loader 3 pairs of lashing points integrated into the front floor, each 10 t Incl. 6 pairs of lashing mushrooms recessed in the upper and side external frame, each 10 t 1 x in the gooseneck area The rest distributed in between, distance not greater than 1200 mm 1 x rear bevel 5 pairs of stake pockets recessed into the external frame, inside 70 x 40 mm (convertible to 5 t ring lashing points, not included) Drawbar for turntable trailer Drawbar with certified 40 mm towing eye Axles + Suspension SAF drum brake axles Axle/undercarriage laser measured for reduced tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounting Brake System 2-line compressed air brake system Colour-coded piping for easy servicing Spring-actuated parking brake 2 non-interchangeable coupling heads at the front with connecting lines to the truck ABS and ALB, with ABS socket at the front, including connection cable Attention: The trailer may only be towed by vehicles that ensure the effective operation of the ABS! Wheels and Tyres 235 / 75 R 17.5 manufacturer's choice Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white front position lights 2 white/red rear marker lights 2 x 7-pin non-interchangeable plugs at the front, with connection cable 1 LED beacon with holder, switched via parking light (removable beacon) 2 pairs of double warning boards, LED illuminated and extendable to 3,000 mm Floor Steel floor in the front section, incl. followed by 70 mm softwood floor, wheel arch areas with steel/checkered plate covering Rear bevel with 70 mm softwood floor Low loader platform incl. rear bevel 8,200 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable covered with wood with spring lift assistance Operating Instructions With 10,000 kg axle load an exemption permit is required, only indivisible loads possible!!! The total weight stated is technically feasible; depending on the cargo, the total weight may not be achievable within the permitted axle, support, and fifth wheel loads (Poor driving and trailing behaviour possible due to incorrect load distribution) Country of Approval / Plates Country of approval: Germany Incl. with Dekra approval and certificate (acco

Durumu: yeni, toplam ağırlık: 16.000 kg, boş ağırlık: 2.400 kg, azami yük ağırlığı: 13.600 kg, makine/araç numarası: d24246f092ae53c0e155d19dd, Further information Chassis tandem trailer Steel welded construction with approx. 152 mm high floor section; load-oriented and torsion-resistant steel frame structure. Longitudinal floor beams with a load-resistant outer frame and a guide tunnel every 600 mm, tunnel with positioning aids at the top and sides; tunnel height approx. 45 mm. 4 interchangeable container corner fittings on 20ft basis. 4 jack legs for jumbo parking height 970 mm, extendable and foldable sideways by 90°, with short safety strut and securing mechanism, pin lock on the frame, sturdy spring bolt as additional transport lock, symmetrical arrangement of legs Form A 2 for CWB C 745 / 782, suitable for parking height approx. 970 mm. Reinforcement between support legs. 7 pairs of lashing rings recessed in the outer frame, each rated at 2.5 t. Heavy-duty pallet stops on both sides, approx. 20–25 mm high, lashing option every 200 mm, loading height reduced by approx. 20–25 mm. Side-mounted door retainers. Rear underrun protection made of flat steel. Flooring Phenolic resin-coated plywood panels, approx. 27 or 30 mm thick (manufacturer's choice), designed for high point load capacity, suitable for forklift axle loads up to max. 4,400 kg. Front bulkhead/corner posts 2,800 mm high, remaining section covered with tarpaulin; volume-optimized steel corner posts; quick-release device for side curtain at front bulkhead. Central stanchions 1 pair of sliding stanchions, adjustable along the full length, with four pockets for insert slats and long lower pocket. Insert slats 3 rows of aluminum V-insert slats or wooden insert slats as per manufacturer, plus 1 additional row of aluminum V-insert slats. Rear wall/corner posts rear Rear steel corner posts up to underside of roof, curtain suspension with round tube and tensioning ratchet. Rear portal doors, double-wing, each with 2 internal locking rods. Curtain Tarpaulin with welded-in horizontal and vertical tension belts. Tension locks in stainless steel. Roof Sliding roof; rear Endlift, can be folded up high at the back, roof slides from rear to front; L-roof beam designed for the automotive industry; internal width between roof beams approx. 2,490 mm, curtain color: white. EcoLift – lifting roof, can be raised by approx. 380 mm, gas-strut assisted. Hodpfx Askt Ni Ueacefn Approval / Plates Country of registration: Germany. Manufacturer's certificate according to EN 12642 XL. Paintwork Chassis hot-dip galvanized. Front corner posts hot-dip galvanized. Front wall aluminum. Rear corner posts hot-dip galvanized. Rear wall white. Tarpaulin RAL 9005 jet black with advertising lettering. Attention! These are archive images.

Durumu: yeni, toplam ağırlık: 35.000 kg, boş ağırlık: 4.900 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22,5², makine/araç numarası: 92df8e9d6c187f34b20298f39, Further Information Chassis Semi-Trailer Tipper Fine-grained steel welded construction, lightweight design, saddle plate with replaceable 2" kingpin Patented curved front end Central telescopic support leg, uncoupling with load not possible; when uncoupled, vehicle must be positioned inclined towards the rear. 2 wheel chocks with holders Foldable underrun protection Half-shell mudguards Integrated mudguard mount, stone-repellent surface With anti-spray splash guards on the last axle only 1 tarpaulin bar with holder 2 towing hooks at the rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Axles in off-road specification Air suspension 1st axle with automatic lift axle, including forced lowering and traction aid, actuated by braking three times (traction aid functional up to 30% axle load exceedance and up to max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded piping for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS electronic braking system, with EBS socket at the front, no connecting cable Note: The trailer must only be towed by tractors that ensure the effectiveness of ABS! With raise & lower valve Vehicle stability control system Wheels and Tires 385/65 R22.5 – manufacturer at the manufacturer's choice Steel rims, factory silver Electrical System 24 volt, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front Hsdei Riz Rjpfx Aacefn 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Actuation hydraulically via truck PTO Bodies Aluminum box body made of high-quality, abrasion-resistant material: front wall 5 mm thick, outer rear walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent upper frame profile. Interior has a step-up at the front wall (not in combination with Cramaro). Shovel and broom holders outside on the front wall. Greenline – conical and aerodynamic body shape Membrane rear wall Rear wall as pendulum tailgate with double-joint hinge, external mounting with double hook locking. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor seamlessly 6 mm thick Standing platform with step-up, connection plate for air/electrical and brake lines with generous clearance for optimal operability. Roll tarpaulin stows to FR-right, with central locking at FR-left Operating Information For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent material degradation and rust. The stated total weight is technically possible. Depending on the cargo, the total weight may not be achievable while complying with permissible axle, support, and kingpin loads. (Poor driving or tracking behavior due to incorrect load distribution possible.) Registration Country / Plates Germany Approval according to EC 2007/46 24/7 Service Hotline Prepared for single-line license plate holder Contour markings with reflective tape according to ECE R 048, white on the side and red at the rear Paintwork Frame DB 7350 Nova Grey 10 years

Durumu: yeni, dingil konfigürasyonu: 2 dingil, toplam ağırlık: 24.000 kg, boş ağırlık: 5.700 kg, azami yük ağırlığı: 18.300 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: b50cac2c60a813b0968994fa0, Further Information Chassis Low-bed Trailer - Steel welded construction - Turntable with robust ball-bearing slewing ring - Foldable rear support - 2 wheel chocks with holders - Full-width rear mudguards - Prepared for extension to 3,000 mm (holes in the outer frame, not in the rear bevel) Lashing Points Low-bed - 1 pair of lashing cutouts recessed at the front in the longitudinal beam at the gooseneck, each rated for 10t - 7 pairs of lashing mushrooms recessed on top and side of the outer frame, each rated for 10t - 1x at the front on the gooseneck - 5x in the low-bed area - 1x in the rear bevel - 12 pairs of lashing holes in the outer frame, each rated for 5t (for tensioning strap hooks) - 5x gooseneck, 6x low-bed, 1x rear bevel Drawbar Hitch Turntable Trailer - Drawbar with tested 40 mm towing eye Axles & Suspension - Drum brake axles, manufacturer’s choice - Laser-aligned axles/chassis to reduce tire wear and fuel consumption - Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker balance) Wheels and Tires - 235 / 75 R 17.5 Fulda - Steel twin wheels, factory silver Brake System - 2-line compressed air brake system - Spring-loaded parking brake - 2 confusion-proof coupling heads at the front, connection lines to tractor vehicle - Connection lines approx. 60 cm extended - Without ABS, but with mechanical ALB, max. 60 km/h permissible Electrics - 12 volts, multi-chamber lights, no side yellow LED lights, side reflectors - 2 white position lights front - 2 white/red lane marker lights rear - 1x 7-pole 12-volt plug at the front, with connection cable, extended by approx. 60 cm - 1 LED beacon with bracket, switched via parking light (removable beacon) - 2 pairs of illuminated, extendable warning boards up to 3,000 mm Floor - Gooseneck front with steel / checker plate covering - Toolbox recessed into drive-over slope at gooseneck - Then 70 mm softwood floor, with steel / checker plate covering in wheel arch area - Rear bevel with 70 mm softwood floor - Low-bed platform including rear bevel: 5,900 mm Loading Ramps Hfedpfx Aaei Ri Agecen - Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable - Wood covered - Supported by spring assist Operating Instructions - For 10,000 kg axle load, a special permit is required; only indivisible loads permitted! - The specified total weight is technically possible; depending on the load, the permissible axle/support/saddle loads may not be achieved (poor tracking and maneuverability possible due to improper load distribution) Country of Registration/Plates - Country of registration: Germany - With Dekra inspection and certificate, for max. 60 km/h approval, towing vehicle LoF (for Switzerland, max. 40 km/h possible) - Prepared for two-line license plate holder - No ECE R 048 compliant contour marking / reflective strips Paintwork - Frame: DB 7350 Novagrau - 10-year warranty against rust-through - Drawbar galvanized or black, manufacturer’s choice - Loading ramps hot-dip galvanized Note: Archive images!

Durumu: yeni, toplam ağırlık: 35.000 kg, boş ağırlık: 4.150 kg, azami yük ağırlığı: 30.850 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, makine/araç numarası: 6e7907b4000c16661fa1c8a1f, Further information Chassis Semi-Trailer Tipper Fine-grain steel welded construction, lightweight design, fifth wheel plate with replaceable 2" kingpin Curved front section, patented without landing gear Wheel chocks with holder Foldable underride guard Half-shell mudguards Integrated mudguard holder, stone-repellent surface Hedpfei Ri Arox Aacsfn Towing hook at rear Axles & suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and traction aid, operated by activating brakes 3x (traction aid functional up to an axle overload of 30% and up to a max speed of 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against corrosion Brake system 2-line compressed air brake system, color-coded piping for easy service. Spring-loaded parking brake 2 anti-swap couplings at the front, without connecting line EBS, electronic braking system with EBS socket at front, without connection cable Note: The trailer may only be towed by tractor units that guarantee effective ABS functionality! With raise & lower valve Vehicle stability control system Wheels and tires 385/65 R22.5, manufacturer at the discretion of the builder Polished aluminum rims, manufacturer at the builder’s discretion Electrics 24 Volt, multi-chamber lights, side-mounted yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK threaded coupling, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck PTO Body Aluminum box body made of high-quality, wear-resistant alloy, front wall 5 mm thick, outer walls made of 30 mm hollow chamber profiles, neatly welded, outer upper edge with bulk material-repelling profile. Interior with access ladder at the front wall (not in combination with Cramaro). Shovel and broom holder on the outside of front wall. Greenline – conical and aerodynamic body shape Membrane – tailgate Tailgate as pendulum flap with double-joint hinge, mounted outside with 2-hook locking system. Tailgate with rubber seal. Note! Heat resistant up to max. 170°C! Continuous 5 mm thick floor, Brinell 110. Note! Only for transporting sand, chippings, and round gravel with a max. grain size up to 20 mm! Warranty does not apply to any other goods! Standing platform with access, connecting plate for air/electrical and brakes with ample space for optimal operation. Roll-up tarpaulin, stashable to FR-right, with central locking on FR-left Operating instructions For transports of salt, lime, etc., we recommend a tipper cylinder with a hard-chromed piston rod to prevent material-induced corrosion. The specified gross vehicle weight is technically possible; depending on load, permissible axle, support, and fifth wheel loads may restrict achievable total weight. (Poor driving and trailing performance possible due to incorrect load distribution) Revolution Link: Revolution Link User Review: Registration Country / Plates Germany With Dekra inspection and report (in accordance with §13 EC-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tape in accordance with ECE R 048, white on the sides, red on the rear Paintwork Frame DB 7350 Nova Grey Body R

Durumu: yeni, toplam ağırlık: 38 kg, boş ağırlık: 4 kg, azami yük ağırlığı: 33 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, makine/araç numarası: a203d9a559ff6484cf2a14c1f, Further information Chassis Semi-Trailer Container Fine-grain steel welded construction, fifth-wheel plate with replaceable kingpin and two kingpin positions Front locking on tipping-cylinder support cradle with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mountings: Locking crossbeams, double position for securing either 1 x 20-foot or 1 x 30-foot container. (Note: Low fifth-wheel load when using 20-foot containers) Adjustment via central telescopic tube frame with interlocking design and pin locking. 24-ton, 2-speed landing gear, single-sided operation, straight lower section, without load balance Clear support foot dimensions or free rear swing radius approx. 1850 mm 2 wheel chocks with holder Half-shell mudguards With anti-spray flaps according to EC specifications Hydraulics Low-pressure cylinder, max. 170 bar, smallest section hard-chrome plated, with HDK screw coupling, fixed part, NW 48 mm. (No hose connection included) Hydraulic operation via truck PTO (power take-off) Hydraulic connection with hose and HDK screw plug, NW = 48 mm with knurled nut Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Axle spacing offset mm (combined transport) up to 44t gross train weight Hjdpsi Ri Avjfx Aacjfn Air suspension Brake system 2-line compressed air brake system Colour-coded pipe routing for easy maintenance Spring-loaded parking brake Tele Control Axle lift for easy telescoping 2 fool-proof coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: This trailer may only be towed by tractors that guarantee ABS functionality! With raise/lower valve Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the driver’s cab (truck must be appropriately pre-equipped, no truck installation included, not a calibrated scale) Wheels and tyres 385/65 R22.5, manufacturer of choice Steel rims, factory silver included Electrics 24 volts, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fool-proof sockets at the front, without connecting cable Additional LED worklight at the rear, switched via reverse light Country of registration / plates Germany EU type approval 2007/46 24/7 service hotline Prepared for single-line number plate holder Contour marking with reflective tape according to ECE R 048, white on sides and red at rear Paintwork Frame finished in DB 7350 Nova Grey 10-year corrosion perforation warranty Support legs coated in black Note: Archive images!

Durumu: yeni, dingil konfigürasyonu: 3 aks, toplam ağırlık: 24.000 kg, lastik boyutu: 235 / 75 r 17,5, makine/araç numarası: 15431365fe5515297a6a9fb05, Further Information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty slewing ring Foldable rear supports 2 wheel chocks with holders Aluminum side underrun protection Full-width rear mudflap Half-shell mudguards for 1st and 2nd axles with anti-spray mudflaps behind each axle; anti-spray mudflaps in front of and behind the 3rd and 4th axles Digger arm recess above the rear axles, extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep; 2 pairs of lashing holes (5 t each) in the digger arm recess, laterally on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear incline 1 plastic toolbox with shelf insert, W=620/H=360/D=440 mm, lockable with a padlock (padlock not included) 1 storage box recessed into neck section in the floor, with lid, W=720 mm / L=520 mm / D=170 mm Extendable widenings to 3,000 mm 70 mm wooden planks for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low-bed trailer lashing points (40 lashing options) 1 pair of 5 t lashing eyes on gooseneck 9 pairs of 10 t lashing pins, recessed into the top and side of the external frame 2 x on the front gooseneck 7 x in the low-bed area 6 pairs of 5 t lashing holes in the external frame of the low-bed (for hook-in tie-down straps) 3 additional pairs of foldable lashing eyes, each 10 t 1 x inside next to the main frame at the start of the low-bed 1 x on the gooseneck (overhanging) 1 x recessed in the floor behind the last axle Trailer drawbar Towing bar with tested 50 mm towing eye, 8° inclined towing eye, D-value at least 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization front and rear (rocker compensation) Wheels and tyres 235 / 75 R 17.5 Manufacturer’s choice Steel rims, twin wheel configuration, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection lines to towing vehicle ABS and ALB, with ABS socket at the front, with connecting cable Hfjdpfx Aasi Ri A Secen Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red tracking lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable 1 LED beacon with holder, operated via parking lights (removable beacon) 2 pairs of double warning boards, LED illuminated and extendable to 3,000 mm Floor Front gooseneck section with steel/chequer plate covering Proceeding with 70 mm softwood flooring, steel/chequer plate covering in the wheel arch area Rear incline with 70 mm softwood flooring Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Wood-covered With spring lift assistance Registration/country plates Country of registration: Germany 24/7-Service Hotline Prepared for two-line license plate holder Conspicuity markings with reflective strips according to ECE R 048, side white and rear red Warning panel according to ECE - 70 Paintwork Frame hot-dip galvanized incl. passivation—15-year corrosion warranty Towing bar galvanized or black, at manufacturer’s option Ramps hot-dip galvanized Note: These are archive photos!