Standart çekici ünitesi

MERCEDES-BENZ Actros 1845 4X2 Spring/Air Mirrorcam Retarder Cl

Durumu: yeni, makine/araç numarası: 56c59c8aba35227ffb44c9f75, boş ağırlık: 11.350 kg, azami yük ağırlığı: 26.650 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Jumbo Chassis Semi-Trailer Steel welded construction with closely spaced cross members, reinforced design, low-loader outer frame profile, suitable for transporting construction machinery up to 32,000 kg and a maximum external machine width of 2550 mm, fifth wheel plate with interchangeable 2'' kingpins. Rear slant approx. 1200 mm at 7°. Enclosed upper ramp shaft with steel/tread plate. In the low-bed section, omega rail laterally below the outer frame serves as a hanging strip for tarpaulins and distance holders for the lashing mushrooms, not in the wheel area. For the lift table: an additional fixed lightweight outer frame with omega profile allows for the lift table to be raised with closed tarpaulin! 24 t, 2-speed landing gear with single-side operation, half-round base and straight mounting plate, with thrust compensation. Free swing radius to rear: approx. 1950 mm. Rear support foldable 2 wheel chocks with holders Side underrun protection made of aluminium Quarter-shell mudguards at front and rear of each axle Anti-spray flaps behind each axle Rear underrun protection made of steel Full-width spray flap across the rear 4 stainless steel toolboxes, w=800/h=350/d=350 mm, with polished doors, lockable; 2 each on FR-left and FR-right in front of the 1st axle Lift table after gooseneck, approx. 3000 mm long, hydraulically liftable for driving over the gooseneck, with mechanical locking in raised position (cylinder angled for good ground clearance, Fliegl standard). Controls on FR-right + additional operation via wireless remote control (same as ramp operation). Lift table can be raised with tarpaulin closed! Tarpaulin hanging on lift table area on an additional lightweight fixed outer frame with omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms remain usable even when table is lowered! Lashing points Gooseneck: 4 pairs of 5 t lashing rings recessed into outer frame 2 pairs of lashing mushrooms, both above and on the sides, recessed into outer frame Low-bed: 8 pairs of lashing mushrooms, both top and side, recessed into outer frame, each 10 t 't 9 pairs of 5 t in outer frame Axles & Suspension SAF drum brake axles Last axle steered, with automatic reverse lock via reversing light, and additional lock feature on vehicle via hand button Air suspension with lift & lower valve + auto-reset function H & S function with quick venting 1st axle is an automatic lift axle, including forced lowering and starting aid, actuated by 3x braking (starting aid is functional up to 30% axle load exceedance and up to a max. speed of 25 km/h) Axle lift is below recommended driving height, therefore no guarantee for tire damage Wheels and Tyres 235 / 75 R 17.5 from leading manufacturers Steel twin wheels, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 tamper-proof coupling heads at front, no connecting line EBS, electronic braking system with EBS socket at front, no connecting cable Note: The trailer may only be towed by trucks that guarantee the effectiveness of the ABS! Itedpfx Aoi Riw Asg Ueb Axle load detection in the truck via EBS, without truck installation (no calibrated scale) Electrical System 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front, in LED 2 white/red lane marker lights at the rear 1 rotating beacon with holder, switchable via parking light (removable beacon) 2 pairs of warning signs, double LED illuminated and e

Durumu: kullanılmış, azami yük ağırlığı: 36.216 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.100 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Üretim yılı: 2024, Donanım: ABS, FAYMONVILLE MAX100 3-axle SANH semi low-loader forklift transport trailer First registration: 10/2024 Unladen weight approx. 13,200 kg Fifth wheel height: 1,150 mm Low-bed length: 9,300 mm Gooseneck length: 3,800 mm Internal width: 2,480 mm Load height in the low-bed: 860 mm Height-adjustable tarpaulin superstructure, adjustable by approx. 400 mm EDSCHA sliding roof, movable forward The structure can be hydraulically widened at the rear portal by approx. 750 mm Loading area behind the gooseneck hydraulically raisable and lowerable, length approx. 2,800 mm; gooseneck and low-bed with grating flooring, over the axles: checker plate flooring with integrated sand coating Two-part steel ramps, approx. 3,185 + 1,420 mm, width 1,250 mm each, also with grating surface, max. load capacity 30,000 kg Tyres: 13 x 235/75 R 17.5 BPW axles with drum brakes 1st axle: LIFT AXLE 3rd axle: STEERABLE TRAILING AXLE Air suspension with raising/lowering function WABCO trailer EBS Itsdpfx Aox Nlhrsg Uob 24-volt E-hydraulics RENTING is the new BUYING – immediately available from us with full-service rental as well.

Durumu: yeni, boş ağırlık: 12.300 kg, azami yük ağırlığı: 37.200 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 30 mm thick hardwood flooring - 3 pairs of lashing rings Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Loading platform: - Loading platform with rear chamfer approx. 1,000 mm x 8° - Approx. 48 mm hardwood flooring, over the axles with checker plate surface Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering axle - Air suspension with lift and lower valve - Self-steering axle with electro-magnetic reverse lockout, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" king pin - One galvanized steel headboard - Yellow-red air couplings on the galvanized connection rail at the front - 4 chocks with holders on the headboard - Mounting at the rear of the gooseneck for ALU drive-on ramps - 3 height levels of aluminum planks Ijdpfxjtvfkfs Ag Uotb - Galvanized folding supports under the chamfer of the loading platform - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized headboard with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - Roof brand "EDSCHA" sliding forward on ALU roof rail profiles, bolted to front and rear wall - 3 pairs of sliding stakes in the loading platform - Body rear left and right hydraulically extendable by approx. 750 mm - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm reserve length, with tension belts at spacing approx. 600 mm - Upper edge of structure approx. 3,960 mm high - Driving with open sliding roof is not permitted and will cause damage to the curtain - Cover plates for bridging the gap between ramps and loading platform - Electro-hydraulic unit at the rear, beneath the loading platform - At the gooseneck and at the ramps left and right each a bracket for warning panels incl. socket - Control valves for the ramps positioned on the right trailer side - 6 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform - Lift axle at the front axle - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm on the right in driving direction between the axles - On the checker plate on the gooseneck and loading platform, a painted sand layer for slip resistance - Central lubrication system BEKAMAX (Pico) with standard lubricant NLGI-2 and removable guard around the pump - Four warning panels extendable by approx. 400 mm, each approx. 423 x 423 mm, with position light - Load pressure gauge for determining axle loads including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then visible defined surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Durumu: yeni, kilometre: 100 km, güç: 375 kW (509,86 bg), yakıt türü: dizel, toplam ağırlık: 32.000 kg, dingil konfigürasyonu: 3 aks, renk: beyaz, vites türü: otomatik, emisyon sınıfı: Euro 6, yükleme alanı uzunluğu: 9.000 mm, yükleme alanı genişliği: 2.550 mm, Üretim yılı: 2025, Donanım: ABS, klima, navigasyon sistemi, park ısıtıcısı, 4-axle Volvo machinery transporter / aerial work platform transporter ? FH 500 8x2R ? Trailing axle, electro-hydraulically steered, single tires ? Rear axle suspension with air suspension: 1 drive axle, 1 trailing axle ? Safety long-distance cab FH ? Cab auxiliary heater, 2 kW ? 33 L cool box with freezer compartment, under the bunk ? Air suspension on front axle(s) ? Transmission / I-Shift operation via driver's seat control unit ? I-Shift driving modes: Standard, Performance, and Economy ? I-See with map-based topography and traffic information ? Eco cruise control (cruise control), including brake cruise control ? Manual shifting possible in automatic mode (including kickdown) ? Adaptive traction control ? Adaptive cruise control (ACC) with collision warning and emergency braking ? Lane keeping assist ? Side collision avoidance and turn assist (both sides) Iedpfow Itmlox Ag Uetb ? Driver alert system (fatigue warning) * VEB Volvo Engine Brake * etc. WIESE superstructure for aerial platform and construction machinery transport, with hydraulic loading ramps with 2 pairs of wheel recesses incl. wheel recess covers Superstructure dimensions: - Length usable approx. 9,050 mm - External width 2,550 mm - Loading height upper edge of floor approx. 1,050 mm unladen - Sturdy, weight-optimized steel welded construction, box-type design - Short crossmember distances for high point loads - Sloped rear for low drive-up angle - Outer frame profile 90° - Bulkhead reinforced version - Storage box inside, below, in front of the bulkhead - Grating floor - Design suitable for 5,000 daN wheel load - Above the axles: steel sheet boxes and outer frame with anti-slip coating Load securing: - 9 pairs of heavy-duty lashing rings, 8 t, recessed into the outer frame - Longitudinal beams with Multi-X contour along the entire length, numerous lashing points 2.5 t - 4 lashing eyes 8 t recessed at the rear (left/right/center/center) - 4 lashing eyes 8 t recessed in front of the bulkhead (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Load capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramps designed as 2 individual, sliding ramps; both ramps are laterally adjustable - Ramp can be used as a drive-up ramp or as a crossover ramp for warehouse equipment (extension part remains closed), the fixed ramp part is placed onto the building ramp - Sturdy tension bar for transport locking (alternative with strap tension) - 2 hydraulic rear supports with pads, including warning tone and indicator light in the cab - Ramp and support operation via electro-hydraulics - Control via radio remote control and emergency controls on the control block - Control block mounted in stainless steel storage box on the frame side - Superwinch 8.2 t winch with approx. 20 m steel cable - Access to load area via steps with handrails right and left - 5 stainless steel storage boxes in pull-out design, incl. lighting as option for an extra charge - Side paneling see example images (green vehicle) as option for an extra charge - KTL coating of superstructure - Ball head trailer coupling at the rear, 3.3 t - 4 LED work lights - 2 LED tail lights mounted high on the bulkhead - 4 exterior-frame LED work lights as area illumination - 2 LED work lights at the rear - 1 revolving beacon at the rear, removable The stock vehicle is supplied with cab in white and superstructure in novagrau; (external frame pain

Durumu: kullanılmış, azami yük ağırlığı: 44.980 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 09/2024, bir sonraki muayene (TÜV): 09/2025, toplam genişlik: 2.550 mm, Donanım: ABS, Our entire fleet of vehicles, including immediately and soon available models, can be found on our website. Selection of features. Complete specifications available on request. Itodpfx Ajlthgujg Uob Chassis, stepped frame: * Special steel frame made from high-strength fine-grained steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle layout. Wheel covers above the axles with spray-suppression * All steel parts sandblasted * Side underrun protection made of anodised aluminum fitted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area to enable the greatest possible low-bed length in combination with AluLeg support legs instead of telescopic landing gears, max. rear swing clearance of the tractor unit approx. 2,100 mm Special superstructure with extendable rear stanchions * Self-supporting aluminum roof bow/profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear stanchions extendable to approx. 4,200 mm * Three sliding stanchions per side with rubber spring relief * Additional middle stanchion lockings in the roof bow and stowage position, actuated by pull cable and spring latch * Mechanically adjustable lifting roof, lift height approx. 400 mm, operable from both sides or one-sided without opening the opposite side or doors * Additional height adjustment approx. 480 mm in approx. 40 mm increments via stanchion adjustment * Front overlap at the bulkhead for driving under tarpaulin up to overall height approx. 4,400 mm * Four rows of approx. 150 mm stackable aluminum slats per side, 450 mm pockets at the bottom, four rows of single pockets above * Only three rows of plug-in slats in the upper deck. Spacings evenly distributed Floor * Approx. 27 mm special water-resistant bonded beech multiplex panels, rough surface * Steel sheeting in the wheel arch area * Suitable for forklift traffic according to DIN ? standard * Outer frame flush finish Brakes * WABCO air brake system with EBS according to EC Directive 71/320 EEC including PREV (Park Release Safety Valve) * Spring-type parking brake cylinders * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer axles with drum brakes, low-loader version * Air suspension with lifting and lowering function, total travel approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical locking Twin tires * 235/75 R 17.5, -16-fold, incl. spare wheel holder, without spare wheel Paintwork * Chassis RAL 3002 red, single color * Middle stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork in single-tone RAL color Special equipment included * ECAS air suspension, operation on the trailer * Oversize signage front and rear, galvanized, stepless telescoping with marker lights incl. bases for revolving beacons (small plates) * Additional external unlocking for sliding tarpaulin frame * 4 stanchion adapters for special outer frame profile, for locking the middle stanchions arbitrarily * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, extra-wide and extra-high version, flat hooks, tarpaulin folds, closures with ratchet/OCS * Rear left telescoping base for revolving beacon incl. light * Outer frame for machinery transport with approx. 64 lashing points in 2,000 kg, 3,000 kg, and 10,000 kg versions, according to construc

Durumu: kullanılmış, azami yük ağırlığı: 31.300 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2019, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.050 mm, toplam genişlik: 2.550 mm, Donanım: ABS, Meusburger MPG-3 Alçak Tır Perdeli, Yönlendirilebilir/Kaldırılabilir Dingil Donanım: Havalı süspansiyon * Dingil kantarı * 1. dingil kaldırılabilir * 3. dingil yönlendirilebilir * Ek destekli ve uzaktan kumandalı hidrolik rampa * Geçişli rampa * Uzaktan kumandalı elektrikli vinç * Edscha tavan * Her iki tarafta depolama kutuları * Yedek lastik (yolda kullanım için) * Ekstra farlar * Çıkarılabilir genişlik levhaları Güvenlik: ABS * EBS * Disk fren Itsdjwfwd Dopfx Ag Usb Hatalar ve ön satış hakkı saklıdır. Dahili araç numarası: 8303

Durumu: kullanılmış, kilometre: 407.000 km, güç: 375 kW (509,86 bg), ilk tescil: 10/2022, toplam ağırlık: 18.000 kg, lastik boyutu: -, dingil konfigürasyonu: 4x2, vites türü: otomatik, emisyon sınıfı: Euro 6, Üretim yılı: 2022, Donanım: klima, MERCEDES ACTROS 1851 EKİM 2022 OTOMATİK RETARDER BUZDOLABI ARKA PNEUMATİK SÜSPANSİYON VE ÖN MEKANİK SÜSPANSİYON ÖN VE ARKA HAVALI SÜSPANSİYON İNGİLİZCE KONUŞUYORUZ ALMANCA KONUŞUYORUZ İSPANYOLCA KONUŞUYORUZ Teslimat süresi (gün): 1 Geri görüş kamerası Klima Itjdpfexwzh Isx Ag Uob Merkezi kilit Buzdolabı Süspansiyonlu koltuk Güç: 510 HP DIN Güç: 375 kW

Durumu: kullanılmış, Fonksiyonellik: tamamen fonksiyonel, kilometre: 505.282 km, güç: 331 kW (450,03 bg), ilk tescil: 04/2021, yakıt türü: dizel, toplam ağırlık: 8.398 kg, dingil konfigürasyonu: 4x2, dingil mesafesi: 385 mm, renk: beyaz, vites türü: otomatik, emisyon sınıfı: Euro 6, Üretim yılı: 2021, silindir sayısı: 6, silindir hacmi: 12.809 cm³, direksiyon simidi pozisyonu: sol, Donanım: hidrolik direksiyon, tam servis geçmişi, Features Iodpfx Agjxrq Ruo Uotb Space Cab Wheelbase 3.80 m / Rear overhang 0.99 m Euro 6 emission standard Engine: MX-13, 355 kW/483 hp. Cab badge: 480 Alternator 120 A, 2x 230 Ah batteries Battery energy monitoring system Automated transmission, TraXon, 12 speeds MX engine brake Aluminum fuel tanks 845+430 l with step, height 620 mm AdBlue tank 90 liters on left wheel arch Driver Comfort Automatic cab climate control Power windows Steering wheel, leather, black color External sun visor, green translucent Curtains along windscreen and side windows Driver's seat: Luxury Air Passenger seat: Comfort Air Driver seat armrest Glass roof hatch, electric control Upper berth Lower berth with standard foam mattress Cabin water-air auxiliary heater 3.8 kW with residual heat pump and timer Refrigerator drawer 42 liters Storage space under lower bunk Technical Specifications Continental VDO 4.1 Smart Tachograph Version 2 – legal requirement from 21.08.2023 Ventilated disc brakes front and rear Electronic braking system ASR (traction control) Maximum capacity fuel tanks Eco-Fuel: The vehicle’s cruise control settings focus on optimal fuel efficiency Front axle: 8.00 t, parabolic, 163N Rear axle: 13.00 t, air suspension, SR1344 Front axle 1: 315/70R22.5 Rear axle 1: 315/70R22.5 Fifth wheel: Jost JSK37C cast iron 150+12mm Safety Predictive Cruise Control Lite Adaptive Cruise Control with FCW and AEBS Vehicle Stability Control (VSC) Lane Keep Assist Axle load monitoring Technology Radio/USB player, 2 speakers Performance assistant Preparation for satellite communication equipment, including GPS/GSM antenna Universal FMS connector Exterior LED headlights LED daytime running lights Fog lamps Adjustable roof deflector for Space Cab Side collars Heated front mirror, MirrorCam, MirrorCam switch on bed Central locking, 2 keys, 2 remote controls

Durumu: yeni, azami yük ağırlığı: 45.250 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Itedpowx Dbiefx Ag Uob Excerpt from the equipment. Full specification available upon request. Chassis, cranked: * Special steel frame made of high-tensile fine-grain steels, electric-welded at connection points * Well-dimensioned outer frame. 4-axle configuration * Wheel arches above the axles with spray suppression * All steel parts are sandblasted * Side underrun protection made of anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the cranked area for the maximum possible low-bed length in combination with alu-leg drop supports instead of telescopic supports, max. rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions extendable for loading/unloading up to approx. 4,200 mm * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks in the roof rail and parking position, via pull cable and spring bolt * DINKEL mechanical lifting roof, height-adjustable * Lifting roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the stanchions * Front overlap at the bulkhead for driving operation under tarpaulin up to total height approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the sides, lower 450 pockets, above it 4 single row pockets. In the high bed only 3 rows of slats, evenly distributed gaps Floor: * Approx. 27 mm specially water-resistant bonded beech plywood, anti-slip surface * Steel plate in wheel arch area, fork-lift truck suitable as per DIN standard * Outer frame surface flush Brakes: * WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF drum-braked axles in low-loader configuration * Air suspension with lift and lower facility, total stroke approx. 230 mm * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * Without spare wheel Lighting: * According to EC standard including LED side marker lights * Position lamps in LED version * 2 additional reversing lights * 2 working lights, inside on front wall, upper side Paintwork: * Chassis and superstructure painted in solid RAL 3002 carmine red * Centre stanchions, axles KTL-coated black * Corner stanchions hot-dip galvanised * Plastic parts black * Galvanised parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signs front and rear in galvanised, infinitely telescopic version, with mounted marker lights including base sockets for rotating beacons (small panels) * Additional unlocking of sliding roof frame from outside * 4 stanchion adapters for special outer frame profile, for securing centre stanchions as desired * PVC sliding tarpaulins, col

Durumu: yeni, kilometre: 400 km, güç: 397 kW (539,77 bg), yakıt türü: dizel, toplam ağırlık: 56.000 kg, dingil konfigürasyonu: 3 aks, renk: beyaz, vites türü: otomatik, Donanım: ABS, elektronik denge programı (ESP), is filtrasyon filtresi, klima, navigasyon sistemi, park ısıtıcısı, Volvo FH540 chassis with Wiese body and Fassi loading crane Volvo FH540 10x4 removable flatbed with F1150RA.2.28 & fly jib, as well as winch and work basket ---Application · Suitable for good roads and normal operating conditions · Long-distance transport · Predominantly flat terrain · Ambient temperature up to +40°C; for more than +40°C, max. 25 h/year · Ambient temperature down to -25°C; for below -25°C, max. 25 h/year · Center of gravity (body and load) approx. 0.5—1 m above upper frame edge · Clean roads; max. 10% soiled · Flatbed chassis without preparations · Technical gross combination weight: 80 t (observe drawbar load limits!) · Special vehicles · Vehicle for crane mounting behind cab · Mirrors adjusted for superstructure width 2,600 mm · New model · Chassis height: MED (medium); precise heights: see VBI/WIS · Electrohydraulically steered trailing axle, single wheel · Rear air suspension, tridem, 2 driven axles · Globetrotter safety cab FH · Wheelbase 4,300 mm · Emission standard: Euro 6 step E, with SCR, particulate filter, and EGR · Diesel engine 12.8 l, 551 hp / 405 kW, 2,652 Nm · Volvo Engine Brake+ (VEB+), braking power: 340 kW / 462 hp (D13S) · Meets ADR brake regulations · I-Shift AT2612, automated 12-speed gearbox (direct drive), max. input torque: 2,652 Nm · Lift axle · Drive axle RTH2610B. Double axle hub reduction. 4 planetary gears · Longitudinal and transverse differential locks · AA tires 315/80R22.5 · Drive axle ratio 3.33:1 · Fuel type: Diesel Ijdpjxl Ip Iefx Ag Ujtb --- Included in delivery: Base unit: F1150RA.2 xhe-dynamic Wiese platform body with drop sides * Execution of all chassis modifications necessary for crane installation, disassembly and reassembly of attachments, exhaust system, tanks, etc. Adaptation of the vehicle frame. All chassis and bodywork are carried out in accordance with the respective chassis manufacturer’s bodybuilder guidelines and executed to the highest quality standards. Complete installation of the custom-designed and -manufactured special subframe made of high-tensile fine-grain steel for crane and body. The welded subframe, bolted to the chassis frame, ensures exceptional torsional rigidity and optimum stability of the crane vehicle. The construction method of the subframe is a unique selling point. Manufactured to the highest quality standards and painted in RAL chassis color. * Installation/bolting of the crane and main stabilizer to the subframe. Installation of all hydraulic and electrical connections. Crane installation location: front * Flatbed design as steel/welded construction, REMOVABLE FLATBED, approx. 4,800 mm long x 2,480 mm wide, with radio-controlled hydraulic extension up to 1,400 mm. Flatbed body: steel / sand-blasted / painted in RAL chassis color. Removable aluminum drop sides by Suer, 600 mm high, anodized finish, standard flatbed with welded 4 mm steel checker plate, painted. * 2 rows MultiSave lashing system recessed and welded into the floor. 6 x Thiele lashing rings 5,000 daN recessed in the floor frame profile. 8 x retractable lashings per side, 2,000 daN, flexible profile/arrangement. * Stable front bulkhead consisting of welded frame, 4 mm steel sheet, 5 x accessory hooks, bulkhead height 1,300 mm, steel / painted in RAL chassis color. Trim panels, mudguards, VA steel design (WIESE look). 4x 20’ container locks at the bulkhead (2x) in the extension.