Alçak şasi dorse

DINKEL 4-Achs-Jumbotieflader - doppelte Rampen

Durumu: yeni, azami yük ağırlığı: 45.250 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available upon request. Chassis, cranked: * Special steel frame made of high-tensile fine-grain steels, electric-welded at connection points * Well-dimensioned outer frame. 4-axle configuration * Wheel arches above the axles with spray suppression * All steel parts are sandblasted * Side underrun protection made of anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the cranked area for the maximum possible low-bed length in combination with alu-leg drop supports instead of telescopic supports, max. rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions extendable for loading/unloading up to approx. 4,200 mm * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks in the roof rail and parking position, via pull cable and spring bolt * DINKEL mechanical lifting roof, height-adjustable * Lifting roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the stanchions * Front overlap at the bulkhead for driving operation under tarpaulin up to total height approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the sides, lower 450 pockets, above it 4 single row pockets. In the high bed only 3 rows of slats, evenly distributed gaps Floor: * Approx. 27 mm specially water-resistant bonded beech plywood, anti-slip surface * Steel plate in wheel arch area, fork-lift truck suitable as per DIN standard * Outer frame surface flush Brakes: * WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF drum-braked axles in low-loader configuration * Air suspension with lift and lower facility, total stroke approx. 230 mm Bjdpfx Abjwx Dbiskjcu * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * Without spare wheel Lighting: * According to EC standard including LED side marker lights * Position lamps in LED version * 2 additional reversing lights * 2 working lights, inside on front wall, upper side Paintwork: * Chassis and superstructure painted in solid RAL 3002 carmine red * Centre stanchions, axles KTL-coated black * Corner stanchions hot-dip galvanised * Plastic parts black * Galvanised parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signs front and rear in galvanised, infinitely telescopic version, with mounted marker lights including base sockets for rotating beacons (small panels) * Additional unlocking of sliding roof frame from outside * 4 stanchion adapters for special outer frame profile, for securing centre stanchions as desired * PVC sliding tarpaulins, col

Durumu: kullanılmış, kilometre: 37.026 km, güç: 270 kW (367,10 bg), ilk tescil: 05/2022, yakıt türü: dizel, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, renk: kırmızı, toplam genişlik: 2.550 mm, toplam yükseklik: 3.900 mm, Üretim yılı: 2022, Donanım: park ısıtıcısı, vinç, Kranunterwagen: Bedjwzhqgspfx Abkocu Motorabgasemissionsstufe V gemäß EU 2016/1628 und TIER 4 gemäß EPA/CARB Kranausleger: - Basismaschine Arbeitsausrüstung: • LICCON-Programmierung für eine spätere Nachrüstung einer Klappspitze • Lasthakenflasche 30,2 t, 3-strängig, mit Doppelhaken Zusätzliche Ausstattung – Unterwagen: • Bereifung 445/95 R 25 (16.00 R 25) • Zusatzheizung, motorunabhängig inkl. Zeitschaltuhr – Fahrerhaus Unterwagen • Staukasten am Fahrzeugheck • Staukasten für Abstützplatten Zusätzliche Ausstattung – Oberwagen: • Zusatzballast 7,3 t (für Gesamtballast 12,8 t) • Zwei elektrisch verstellbare Arbeitsstrahler am Schwenkwerk sowie Arbeitsstrahler auf der drehbaren Plattform (je 2 seitlich und 2 hinten) Zwischenzeitlich wurde der Kran beschriftet. Angebot freibleibend. Ohne Verpflichtung oder Garantie. Zwischenverkauf vorbehalten. Für eine Reservierung ist eine Anzahlung von 10 % des Kaufpreises erforderlich. Bis das Geld nicht auf unserem Konto eingegangen ist, besteht keine Reservierung und kein Anspruch auf Verfügbarkeit. Der Kaufvertrag kommt erst mit vollständigem Zahlungseingang auf unserem Konto zustande. Das Fahrzeug bleibt bis zur vollständigen Bezahlung unser Eigentum. Zahlungen akzeptieren wir ausschließlich in Euro, spesenfrei für den Verkäufer und ausschließlich per Überweisung. Keine Schecks.

Durumu: mükemmel (kullanılmış), kilometre: 582.537 km, ilk tescil: 04/2009, yakıt türü: dizel, dingil konfigürasyonu: 10x4, yakıt: dizel, frenler: retarder, renk: beyaz, şoför kabini: yataklı kabin, vites türü: mekanik, emisyon sınıfı: Euro 5, Üretim yılı: 2009, Donanım: ABS, elektrikli ayna, elektrikli cam sistemi, hız sabitleyici, is filtrasyon filtresi, klima, park ısıtıcısı, retarder, spoiler, vinç, = Additional Options and Accessories = - Aluminum fuel tank - Low noise - Speed limiter - Refrigerator - Air suspension - Air horn - Particulate filter - Sun visor - Stability control - Auxiliary heater - Toolbox - Power take-off (PTO) - Central lubrication system = Additional Information = Axle Configuration Front axle 1: Steering Front axle 2: Steering Rear axle 1: Steering Rear axle 2: Twin tyres Rear axle 3: Twin tyres Weights Unladen weight: 36,399 kg Payload: 17,601 kg Gross vehicle weight: 54,000 kg Functional Boom: Telescopic (8 sections) Boom length: 24 m Lifting capacity: 30,000 kg Lifting height: 2,400 cm Crane: FASSI F1500AXP.28, behind the cab Body brand: FASSI F1500AXP.28 CE marking: yes Condition Technical condition: very good Visual condition: very good Financial Information Price: On request Bsdpouxu Thsfx Abkjcu Identification Registration: BV-XP-06 DAF XF 105.510 10X4 Tractor Unit + FASSI F1500AXP.28 CRANE EURO 5 L PACKAGE 480 HP DRIVE 10X4 WHEELBASE 570 CM AIR SUSPENDED XF SLEEPER CAB WITH AIR CONDITIONING, AUXILIARY HEATER, REFRIGERATOR MANUAL GEARBOX FIFTH WHEEL MANY TOOLBOXES FASSI F1500AXP.28 CRANE 150 T/M CRANE!!! 2X OIL COOLER FOR CRANE HYDRAULICS 8X HYDRAULIC EXTENSIONS WORKING HEIGHT 24 METRES MAX LIFTING CAPACITY 30,000 KG MAX LIFTING CAPACITY AT 19.4 METRES: 4,465 KG CENTRAL LUBRICATION SYSTEM ON THE CRANE 4X OUTRIGGERS REMOTE CONTROL FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN WE SPEAK ENGLISH HABLAMOS ESPAÑOL

Durumu: kullanılmış, kilometre: 130.506 km, güç: 270 kW (367,10 bg), ilk tescil: 05/2017, yakıt türü: dizel, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, renk: kırmızı, vites türü: otomatik, toplam genişlik: 2.550 mm, toplam yükseklik: 3.800 mm, Üretim yılı: 2017, Donanım: klima, park ısıtıcısı, vinç, CRANE CARRIER Engine exhaust emissions in accordance with 97/68/EC Stage IV and Tier 4-final per EPA/CARB regulations Working equipment: Mounting bracket for double lattice-type swing-away jib including programming, Preparation for second hoist, 30.2 t hook block with three sheaves and double hook, Second boom head top sheave Bedpfx Asxd Nc Hsbkjcu Additional equipment – Carrier: Tires 445/95 R 25 (16.00 R 25), Engine-independent heater for carrier cabin including timer, Storage box at rear of crane (not in combination with spare wheel holder), Storage box for outrigger timbers, Outrigger base registration system, Air conditioning in carrier cabin, 12V socket for carrier cabin Additional equipment – Superstructure: Additional counterweight 5 t (for total 12 t ballast), Air conditioning in crane cabin, Workspace limitation system, Remote diagnostics with GSM module, Second hoist end switch, Two electrically adjustable working floodlights at pivot section, Anemometer (wind speed indicator), 12V socket in crane cabin, LICCON data logger with analysis software (Liftanalyser), LICCON job planner Operating hours superstructure: 5,750 / Operating hours undercarriage: 3,830 (as of 02.2025) (In the meantime, the crane has been lettered/labeled.) All cranes are available at short notice and can be inspected by appointment. Current inspection reports (general inspection, safety inspection, accident prevention standards) are available. Hüffermann Krandienst GmbH: We trade, we rent, we repair. Roll-off trailers, roll-off tippers, refuse collection vehicles, mobile cranes, and aerial work platforms... Contact us! Financing desired? We are happy to prepare a non-binding financing offer for you. The offer is non-binding, without warranty or guarantee. Subject to prior sale. For a reservation, a deposit of 10% of the purchase price is required. No reservation or claim to availability until payment is received. The purchase is concluded only once the full payment has been credited to our account. The vehicle remains the property of Hüffermann Krandienst GmbH until payment is received in full. Payments are accepted exclusively in Euro, free of charge for the seller, and only via bank transfer. No checks.

Durumu: kullanılmış, azami yük ağırlığı: 36.216 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.100 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Üretim yılı: 2024, Donanım: ABS, FAYMONVILLE MAX100 3-axle SANH semi low-loader forklift transport trailer First registration: 10/2024 Unladen weight approx. 13,200 kg Fifth wheel height: 1,150 mm Low-bed length: 9,300 mm Gooseneck length: 3,800 mm Bedpfx Abox Nlhrekscu Internal width: 2,480 mm Load height in the low-bed: 860 mm Height-adjustable tarpaulin superstructure, adjustable by approx. 400 mm EDSCHA sliding roof, movable forward The structure can be hydraulically widened at the rear portal by approx. 750 mm Loading area behind the gooseneck hydraulically raisable and lowerable, length approx. 2,800 mm; gooseneck and low-bed with grating flooring, over the axles: checker plate flooring with integrated sand coating Two-part steel ramps, approx. 3,185 + 1,420 mm, width 1,250 mm each, also with grating surface, max. load capacity 30,000 kg Tyres: 13 x 235/75 R 17.5 BPW axles with drum brakes 1st axle: LIFT AXLE 3rd axle: STEERABLE TRAILING AXLE Air suspension with raising/lowering function WABCO trailer EBS 24-volt E-hydraulics RENTING is the new BUYING – immediately available from us with full-service rental as well.

Durumu: yeni, makine/araç numarası: 56c59c8aba35227ffb44c9f75, boş ağırlık: 11.350 kg, azami yük ağırlığı: 26.650 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Jumbo Chassis Semi-Trailer Steel welded construction with closely spaced cross members, reinforced design, low-loader outer frame profile, suitable for transporting construction machinery up to 32,000 kg and a maximum external machine width of 2550 mm, fifth wheel plate with interchangeable 2'' kingpins. Rear slant approx. 1200 mm at 7°. Enclosed upper ramp shaft with steel/tread plate. In the low-bed section, omega rail laterally below the outer frame serves as a hanging strip for tarpaulins and distance holders for the lashing mushrooms, not in the wheel area. For the lift table: an additional fixed lightweight outer frame with omega profile allows for the lift table to be raised with closed tarpaulin! 24 t, 2-speed landing gear with single-side operation, half-round base and straight mounting plate, with thrust compensation. Free swing radius to rear: approx. 1950 mm. Rear support foldable 2 wheel chocks with holders Side underrun protection made of aluminium Quarter-shell mudguards at front and rear of each axle Anti-spray flaps behind each axle Rear underrun protection made of steel Full-width spray flap across the rear 4 stainless steel toolboxes, w=800/h=350/d=350 mm, with polished doors, lockable; 2 each on FR-left and FR-right in front of the 1st axle Lift table after gooseneck, approx. 3000 mm long, hydraulically liftable for driving over the gooseneck, with mechanical locking in raised position (cylinder angled for good ground clearance, Fliegl standard). Controls on FR-right + additional operation via wireless remote control (same as ramp operation). Lift table can be raised with tarpaulin closed! Tarpaulin hanging on lift table area on an additional lightweight fixed outer frame with omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms remain usable even when table is lowered! Lashing points Gooseneck: 4 pairs of 5 t lashing rings recessed into outer frame 2 pairs of lashing mushrooms, both above and on the sides, recessed into outer frame Low-bed: 8 pairs of lashing mushrooms, both top and side, recessed into outer frame, each 10 t 't 9 pairs of 5 t in outer frame Axles & Suspension SAF drum brake axles Last axle steered, with automatic reverse lock via reversing light, and additional lock feature on vehicle via hand button Air suspension with lift & lower valve + auto-reset function H & S function with quick venting 1st axle is an automatic lift axle, including forced lowering and starting aid, actuated by 3x braking (starting aid is functional up to 30% axle load exceedance and up to a max. speed of 25 km/h) Axle lift is below recommended driving height, therefore no guarantee for tire damage Wheels and Tyres Bcjdpfei Riw Ajx Abkju 235 / 75 R 17.5 from leading manufacturers Steel twin wheels, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 tamper-proof coupling heads at front, no connecting line EBS, electronic braking system with EBS socket at front, no connecting cable Note: The trailer may only be towed by trucks that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck installation (no calibrated scale) Electrical System 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front, in LED 2 white/red lane marker lights at the rear 1 rotating beacon with holder, switchable via parking light (removable beacon) 2 pairs of warning signs, double LED illuminated and e

Durumu: yeni, azami yük ağırlığı: 36.461 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.480 mm, toplam yükseklik: 860 mm, Üretim yılı: 2025, Technical Description Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Area: Hydraulically liftable and lowerable platform after the gooseneck, approx. 2,800 mm in length, with rear taper approx. 1,000 mm x 8°. 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN). 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN). 1 pair of foldable lashing rings to the inside on the front central beam (LC 10,000 daN). Grating floor covering C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles tread plate covering. Two-Piece Steel Ramps: One pair of galvanized two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating covering C40/5 (point load 8 t on an area of 20 x 20 cm). Ramps with hydraulically folding ramp sections and hydraulic lifting mechanism. Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not included in the overall vehicle length of 16,500 mm. Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R17.5 3PMSF tyres at the manufacturer’s discretion. TPMS: TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface according to ISO 11992. For proper display, the towing vehicle must be capable of transmitting and displaying this data. Bodpfx Abew Dl Hwskocu Axles: BPW axles and suspension, 2 rigid axles, 1 trailing steering axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated by reverse gear and manually. Air suspension with lift and lower valve. Axle tools. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit. Electrical System: Electrical system complying with EU regulations, 24-volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicators. ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Manufactured from high-strength fine-grained steels. Steel grades: – S355J2+N / S355MC (yield strength 355 MPa) – S690QL / S700MC (yield strength 690 MPa) Curtain Body: Curtain body ??? 3,960 mm ??? – Galvanized front wall with tensioning system for sliding curtains. – "EDSCHA" brand roof, forward-sliding on ALU roof bow profiles (bolted to front and rear wall). – 3 pairs of sliding stakes in the loading area. – Rear of the body hydraulically extendable to left and right by approx. 750 mm. – Sliding roof with upwards foldable portal beam. – Sliding curtain with 700 mm length reserve, lashing straps approx. every 600 mm. – Height to upper edge of body approx. 3,960 mm (loaded). – Driving with open sliding roof is prohibited and will damage the curtain. Paintwork: Entire steel structure is automatically blast-cleaned with a wheel blasting machine after welding. Second blast treatment with corundum for optimal coating adhesion. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection. Final painting with 2 coats of 2K topcoat, single colour, shade of choice according to RAL system 841GL. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint.

Durumu: yeni, boş ağırlık: 12.300 kg, azami yük ağırlığı: 37.200 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 30 mm thick hardwood flooring - 3 pairs of lashing rings Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Loading platform: - Loading platform with rear chamfer approx. 1,000 mm x 8° - Approx. 48 mm hardwood flooring, over the axles with checker plate surface Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering axle - Air suspension with lift and lower valve - Self-steering axle with electro-magnetic reverse lockout, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" king pin - One galvanized steel headboard - Yellow-red air couplings on the galvanized connection rail at the front - 4 chocks with holders on the headboard - Mounting at the rear of the gooseneck for ALU drive-on ramps Bcjdpstvfkfofx Abkju - 3 height levels of aluminum planks - Galvanized folding supports under the chamfer of the loading platform - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized headboard with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - Roof brand "EDSCHA" sliding forward on ALU roof rail profiles, bolted to front and rear wall - 3 pairs of sliding stakes in the loading platform - Body rear left and right hydraulically extendable by approx. 750 mm - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm reserve length, with tension belts at spacing approx. 600 mm - Upper edge of structure approx. 3,960 mm high - Driving with open sliding roof is not permitted and will cause damage to the curtain - Cover plates for bridging the gap between ramps and loading platform - Electro-hydraulic unit at the rear, beneath the loading platform - At the gooseneck and at the ramps left and right each a bracket for warning panels incl. socket - Control valves for the ramps positioned on the right trailer side - 6 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform - Lift axle at the front axle - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm on the right in driving direction between the axles - On the checker plate on the gooseneck and loading platform, a painted sand layer for slip resistance - Central lubrication system BEKAMAX (Pico) with standard lubricant NLGI-2 and removable guard around the pump - Four warning panels extendable by approx. 400 mm, each approx. 423 x 423 mm, with position light - Load pressure gauge for determining axle loads including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then visible defined surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Durumu: yeni, kilometre: 100 km, güç: 375 kW (509,86 bg), yakıt türü: dizel, toplam ağırlık: 32.000 kg, dingil konfigürasyonu: 3 aks, renk: beyaz, vites türü: otomatik, emisyon sınıfı: Euro 6, yükleme alanı uzunluğu: 9.000 mm, yükleme alanı genişliği: 2.550 mm, Üretim yılı: 2025, Donanım: ABS, klima, navigasyon sistemi, park ısıtıcısı, 4-axle Volvo machinery transporter / aerial work platform transporter ? FH 500 8x2R ? Trailing axle, electro-hydraulically steered, single tires ? Rear axle suspension with air suspension: 1 drive axle, 1 trailing axle ? Safety long-distance cab FH ? Cab auxiliary heater, 2 kW ? 33 L cool box with freezer compartment, under the bunk ? Air suspension on front axle(s) ? Transmission / I-Shift operation via driver's seat control unit ? I-Shift driving modes: Standard, Performance, and Economy ? I-See with map-based topography and traffic information ? Eco cruise control (cruise control), including brake cruise control ? Manual shifting possible in automatic mode (including kickdown) ? Adaptive traction control ? Adaptive cruise control (ACC) with collision warning and emergency braking ? Lane keeping assist ? Side collision avoidance and turn assist (both sides) ? Driver alert system (fatigue warning) * VEB Volvo Engine Brake * etc. WIESE superstructure for aerial platform and construction machinery transport, with hydraulic loading ramps with 2 pairs of wheel recesses incl. wheel recess covers Superstructure dimensions: - Length usable approx. 9,050 mm - External width 2,550 mm - Loading height upper edge of floor approx. 1,050 mm unladen - Sturdy, weight-optimized steel welded construction, box-type design - Short crossmember distances for high point loads - Sloped rear for low drive-up angle - Outer frame profile 90° - Bulkhead reinforced version - Storage box inside, below, in front of the bulkhead - Grating floor - Design suitable for 5,000 daN wheel load - Above the axles: steel sheet boxes and outer frame with anti-slip coating Load securing: - 9 pairs of heavy-duty lashing rings, 8 t, recessed into the outer frame - Longitudinal beams with Multi-X contour along the entire length, numerous lashing points 2.5 t - 4 lashing eyes 8 t recessed at the rear (left/right/center/center) - 4 lashing eyes 8 t recessed in front of the bulkhead (left/right/center/center) - Outer frame profile 90° Loading ramps: Type: WFB 20 S-2 Load capacity: 18,000 kg per pair Platform length approx.: 4,360 mm (2,725 mm + 1,635 mm) Platform width approx.: 850 mm per ramp - Ramps designed as 2 individual, sliding ramps; both ramps are laterally adjustable - Ramp can be used as a drive-up ramp or as a crossover ramp for warehouse equipment (extension part remains closed), the fixed ramp part is placed onto the building ramp - Sturdy tension bar for transport locking (alternative with strap tension) - 2 hydraulic rear supports with pads, including warning tone and indicator light in the cab - Ramp and support operation via electro-hydraulics - Control via radio remote control and emergency controls on the control block - Control block mounted in stainless steel storage box on the frame side - Superwinch 8.2 t winch with approx. 20 m steel cable - Access to load area via steps with handrails right and left - 5 stainless steel storage boxes in pull-out design, incl. lighting as option for an extra charge Bjdpfx Abow Itmljkocu - Side paneling see example images (green vehicle) as option for an extra charge - KTL coating of superstructure - Ball head trailer coupling at the rear, 3.3 t - 4 LED work lights - 2 LED tail lights mounted high on the bulkhead - 4 exterior-frame LED work lights as area illumination - 2 LED work lights at the rear - 1 revolving beacon at the rear, removable The stock vehicle is supplied with cab in white and superstructure in novagrau; (external frame pain

Durumu: yeni, azami yük ağırlığı: 25.300 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. Gooseneck * Gooseneck in SNT design for optimized deck length * Length approx. 3,750 mm; gooseneck hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg. Suitable for tractors: 4 x 2 and 6 x 2 Tanker deck * Low bed designed as extendable tanker deck in SUPER LOW design * Length approx. 6,850 mm * with mechanical locking * Supply lines are protected in extendable beams and automatically adjust to the respective low bed length Rear running gear * In short version with closed outer frame and checker plate cover * Running gear with excavator trough, this is closed in the rear section to house air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Bcsdev Sw E Aepfx Abksu Braking system * Make: WABCO. EBS-E according to EU regulations, WITHOUT connection cable to the tractor unit Paintwork * 6-coat treatment * Complete steel structure shot-blasted after welding * 1 layer zinc-based primer * 1 layer adhesion primer. Final coating with 2 layers of 2K (acrylic) single-color paint, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver-grey * Sidewall color: Natural Aluminum Accessories included * Plug-in steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations, excluding hydraulic winches. Without installation of supply connections on the tractor unit * Mounting adapter for 1 spare wheel in front of the gooseneck’s front wall * Outer beams of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then every approx. 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear chamfer of the gooseneck (LC 6,000 daN) * 2-inch king pin * Hydraulic spreader beam for supporting the gooseneck on the tractor or a dolly * Air connection with air gun on the gooseneck * 1 pair of steel ramps with climbing strips and mounting bolts to bridge the low bed’s mounting hooks * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * On the outer beams of the loading area, provisions for removable load floor * Lashing rings with retaining spring approx. every 1,200 – 1,300 mm outside on the inner beams of the loading area * Lashing rings with retaining spring approx. every 1,200 – 1,300 mm outside on the outer beams of the loading area (LC 10,000 daN) * Cutouts in the upper chord of the outer beams above the lashing rings * Mechanical bolt-tab coupling from the low bed to the running gear, for deck replacement or installation of extension beams. With electro-pneumatic-hydraulic couplers * Outer beams of the low bed coated with anti-slip sand layer * 2nd driving height for upper driving position, max. ± 50 mm from normal driving position, without installation of controls from the tractor unit * 1 pair of lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Chamfered front and rear a