Kullanılmış Müller-Mitteltal Değiştirilebilir Şasi satın al (260)

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2024, * PT 30 Profile: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lifting and lowering feature as well as RtR valve * Smart-Board installed as infotool on the trailer (for axle load display—front and rear separated) * Tire pressure monitoring with display option in the truck via EBS signal, without installation on truck side * Side underrun protection * Swivel support legs at the rear chassis frame * Mechanically adjustable warning board packages front and rear * Front axle plastic quarter mudguards with splash protection * Rear axle straight galvanized steel skirts with splash protection * Reflective contour tape on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Toolbox, galvanized sheet steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted on right side * Compartment in the bogie for accessories with folding lid, 2 container locks permanently installed (directly behind bogie platform) * ROBOT-welded anti-slip coating on the steel surface of the bogie platform (protruding weld beads) Dedpfx Agsxptn Rs Toul * Load securing package consisting of: 2 lashing rings (13.4 t) front left & right on the front wall carrier; front & rear, 1 pair each of UVV lashing rings (13.4 t); and 3 pairs per side of UVV lashing rings (10 t) – pivotable and lowerable, loadable in all directions and integrated in side frame; 3 each side stanchion pockets with simultaneous 2 t lashing capability * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear slope) * Widening planks stowed in the center of the loading platform * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically adjustable side-to-side * 4-way control block for retrofitting hydraulic ramp displacement * Chassis, bogie, folding outriggers, drop legs and loading ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in a black shade * Loaded loading height approx. 910 mm +/- 20 mm with air suspension * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: kullanılmış, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 11/2004, bir sonraki muayene (TÜV): 08/2026, * Müller Mitteltal TS3 alçak şasi treyler (dorseli) * İlk tescil: 11/2004 * 3 aks * Havali süspansiyon * Gigant akslar * Hidrolik uzun rampalar, kaydırılabilir ve katlanabilir * Yatak genişliği 2,50 m'den 3,0 m'ye kadar artırılabilir * Yükleme uzunluğu: 8,50 m, yükseklik: 0,85 m * Boyun kısmında yükleme uzunluğu: 3,40 m, yükseklik: 1,50 m * Destek ayakları Duodjw Tgkbopfx Ag Tjl * Boş ağırlık: 10.260 kg * Teknik toplam ağırlık: 47.000 kg * Muayene geçerlilik: 08/2026'ya kadar * Genel muayene: 02/2026'ya kadar geçerli

Durumu: kullanılmış, boş ağırlık: 2.700 kg, azami yük ağırlığı: 7.300 kg, toplam ağırlık: 10.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 02/2007, yükleme alanı uzunluğu: 5.020 mm, yükleme alanı genişliği: 2.460 mm, yükleme alanı yüksekliği: 400 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: turuncu, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Vehicle location: Bovenden, 2 axles, BPW axles, tandem, leaf suspension, ABS (anti-lock braking system), lashing rings, mechanical ramps, front support legs, storage box, height-adjustable drawbar. Body: Tandem low-bed trailer with mechanical drive-on ramps, 2 BPW axles, drum brakes! Loading height approx. 930 mm! Ramp length approx. 2,600 mm! Dodpswvikqefx Ag Tsul ACCESSORY SPECIFICATIONS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Durumu: yeni, azami yük ağırlığı: 38.900 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T5 Profile 50.0: * Wabco EBS (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake actuators * Drum brakes * 4 x 11-ton Gigant axles * Last axle is self-steering (Locking of the self-steering axle from the cab for maneuvering is possible without truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension with lift/lower system and RtR valve * 3rd axle liftable (ride height +30 mm when axle is lifted) * Forced unloading and forced lowering of the lift axle for maneuvering purposes (truck-side installation required), controlled depending on speed via the EBS electronics * Smartboard as info tool with pressure sensors for total axle load display by axle group Dodjl Tihuopfx Ag Toul * Tire pressure monitoring with truck cabin display option via EBS signal (without truck-side installation) * Mechanical warning sign kit for 3 m overall width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable LED beacon at the rear * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, left side * Front fenders made of plastic, rear fender skirts made of galvanized sheet steel * Turntable platform front with 45° corners and 3 storage compartments with lockable folding lids (lids opening to rear) * Lowering of the low-bed platform by 500 mm to 6,280 mm incl. extended recessed neck 500 mm forward * Load securing package: 2 x 6.4 t lashing rings at the front corners, 2 x 13.4 t UVV-lashing rings at the front and rear side corners respectively, 5 x 10 t UVV-lashing rings each side (pivoting, lowering, multi-directional load capability), 4 stake pockets per side with simultaneous 2 t lashing capability, 1 x 16 t UVV-lashing ring on the rear cross member * Rubber covering on the folding ramp, driving slope and running surface of the low loader platform * Bamboo wooden insert between the side members in front of the excavator stick cradle * Extendable and foldable outriggers for 3 m overall width (plank holder under chassis, right side) * Continuous excavator stick cradle with reinforcement profile from last axle to end cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV-lashing rings laterally in the excavator stick cradle * Hydraulic folding ramp with dual line hydraulics and extendable pointed section approx. 4,650 x 720 mm including load-holding valves and hydraulic lateral shift * Hydraulic rear support * Hydraulic flow divider (for hydraulic pump output on truck of over 40 l/min up to max. 140 l/min) * Loaded loading height 890 mm +/- 20 mm via air suspension * Loading area above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm driving slope * Chassis, turntable, drawbar, extension brackets, and ramps hot-dip galvanized * Drawbar, axles, hydraulic axle supports, and air tanks painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 14/2026

Durumu: kullanılmış, boş ağırlık: 5.100 kg, azami yük ağırlığı: 14.900 kg, toplam ağırlık: 20.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 02/1997, yükleme alanı uzunluğu: 8.200 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: mavi, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Vehicle location: Bovenden, 2 axles, SAF axles, turntable, leaf suspension, lashing eyes, mechanical ramps, rear support, lateral aluminium underrun protection, twin tires. Body: 2-axle low-bed trailer with mechanical drive-on ramps, 2x SAF axles, drum brakes! Dedov R Hmajpfx Ag Teul Loading height approx. 900 mm! Ramp length approx. 2650 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Durumu: yeni, azami yük ağırlığı: 27.940 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t axles * Air suspension with raise/lower function and RtR valve * Start-assist for maneuvering via EBS to the first axle (no truck-side installation) with lifted lift axle +30 mm ride height Dsdpfx Agjwh Hdxs Teul * Smart-Board information tool mounted on trailer with pressure sensors for total axle load display * Last axle configured as self-steering axle with electro-pneumatic steering lock * Steering lock for the self-steering axle can be activated from the tractor for maneuvering via EBS (without truck-side installation) * 2" king pin * 1 liftable axle * Side underrun protection * Front aluminum drop legs and rear swinging supports on chassis * Alcoa LVL One aluminum rims * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 2 LED work lights on trailer sides (no truck-side installation) * 7-pin socket at rear for overlength lighting * Side marker lights with indicator function * Tire pressure monitoring with in-cab display option via EBS signal (without truck-side installation) * Mechanically adjustable warning sign holder packages front and rear * Straight steel fenders * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated sheet steel (W = 2,480 mm x H = 500 mm x L = 665 mm) with top folding lid and side doors in the chamfered corners * On each side of the fifth-wheel platform, 400 mm high aluminum drop sides (RAL 9010 pure white), foldable and removable * Rear drop-in wall, 150 mm high * Rear slant on the fifth-wheel platform to the lowbed, approx. 700 mm long with checker plate and perforated strip for attaching aluminum loading ramps * Fifth-wheel and lowbed platforms with 50 mm clamped wooden planks * Tread plate above axles * Preparation for 3 receptacle shafts under the fifth-wheel platform for storing optional aluminum ramps * Swivel arm as a carrier for connecting lines from the truck to the trailer * Load securing package consisting of: perforated outer frame on the fifth-wheel platform, 45° bent with hole pattern for lashing equipment (2 t lashing force per point with min. 480 mm spacing), 2 x 6.3 t recessed lashing rings on each side, 1 x 16.5 t lashing ring per side on the slope from lowbed platform to fifth-wheel platform, 2 pairs of 16.5 t lashing rings in the lowbed platform (1 pair on the longitudinal beams after the step, 1 pair over the middle axle next to the longitudinal beam), 3 x 13.4 t lashing rings per side on the outer frame (1 at beginning of fifth-wheel frame step, 1 at start of ramp slope, 1 at end of ramp slope), 3 x 10 t lashing rings each side (2 between front wheel recess and 1st axle, 1 between 2nd and 3rd axle), 3 x 5 t lashing rings per side bolted to the outer frames of the wheel recesses (2 at the front, 1 at the rear) * Extended excavator arm resting area from the end of the last rigid axle over the steering axle to the rear cross member, continuous with internal reinforcement profile approx. W = 770 mm x Depth rear = 270 mm / Depth front 170 mm; 2 x 6.4 t lashing rings per side in the excavator arm rest * 2 wheel recesses per side, 390 mm deep and 640 mm wide, for transporting wheel loaders with a wheelbase of 3,000 – 3,590 mm and a tire diameter of 1,760 mm – with sliding covers * 2nd sliding cover...

Durumu: kullanılmış, boş ağırlık: 6.500 kg, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2008, bir sonraki muayene (TÜV): 03/2024, yükleme alanı uzunluğu: 8.000 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 910 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: turuncu, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Vehicle location: Bovenden, leaf suspension, 3 axles, BPW axles, turntable, ABS (anti-lock braking system), lashing eyes, hydraulic ramps, rear support, side aluminium underrun protection, twin tires, storage box. Body: Hydraulic ramps, extendable to 3 m. BPW axles, drum brakes, lashing rings on the outside. Ramp length approx. 4000 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale and errors excepted! Duedpfx Agjqpgtmj Tsl

Durumu: yeni, azami yük ağırlığı: 30.500 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Tire pressure monitoring system with display in the truck via EBS signal -no installation required on the truck- * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages at front & rear * SmartBord information tool mounted with pressure sensors for axle load display per axle group * Reflective contour tape on the sides and rear * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Closed plastic single mudguards at the front * Straight steel rear mudguards each with spray protection (anti-spray devices) * Side underrun protection * Front section ahead of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lid opens to the rear) * Chassis made from high-strength fine-grained steel * Floor above the turntable platform: 50 mm coniferous wood; on the low-bed platform: 60 mm coniferous wood * Outer planks of the drive-on ramps made from 50 mm hardwood * Load securing package consisting of: 2 lashing eyes, 6.4 t each, at the front left and right on the main frame of the turntable platform; 1 pair of 13.4 t lashing rings at the side, front and rear, on the outer frame; moreover, 1 pair of 10 t lashing rings per side, pivotable and lowerable, loadable in all directions and recessed in the outer frame; 5 t lashing rings screwed to the outer frame of the wheel recesses (2 each at the front and 1 at the rear wheel recess); 2 pairs of 6.4 t lashing rings at the side in the excavator arm storage area * 11 pairs of folding outriggers for 3 m overall width (not at the tapering rear end) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for widening planks, made of sheet steel, mounted transverse to the loading area in front of the 1st rear axle Dedpfx Agoxmpyke Toul * Excavator arm trough above the rear axle to the end of the approach slope, approx. 2,300 x 740 x 190 mm * Each side with 2 wheel recesses, approx. 640 mm wide; front 340 mm deep, rear 220 mm deep, with sliding covers (storage for covers at the front on the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height (laden) approx. 890 mm +/- 20 mm (including 860 mm approach slope) * Chassis, turntable, folding outriggers, rear drop-down supports, and access ramps all hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from KW 14/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7-ton Gigant axles * Parabolic springs with tandem equalizer unit * Tire pressure monitoring with in-cab display via EBS signal (no truck-side installation required) * Height-adjustable drawbar, adjustable by 300 mm, with 40 mm flange towing eye * Mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underride guard * Plastic quarter mudguards * Net hooks on the sides and rear in locking bar mounts, plus 2 on the front bulkhead * Main frame made of fine-grain steel * Steel pallet platform with three-way tipper body, fixed smooth steel front wall, continuous drop sides (foldable without center posts), with drop side lift assist and swinging via manual central locking * Rear stanchions bolted * Steel rear wall inserted in front of ramps * Each corner with 1 x 5-ton lashing point, and each side with 4 x 3-ton lashing rings recessed in the outer frame * 4 mm fine-grain steel floor * Two-part mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (can be manually retracted up to 80 mm) * Chassis, drawbar, rear stanchions, underride guard, mechanical fall supports, and loading ramps hot-dip galvanized Dujdpfx Aotr Sucsg Tjl * Axles, springs, air tank, flange towing eye, and landing gear painted black * Drop sides and bed painted RAL 9010 pure white * Drop side and tipping platform painting in any RAL color available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Durumu: yeni, azami yük ağırlığı: 10.950 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2026, * ETÜ-TA-ER 14.4 flatbed trailer: * RDÜ (tyre pressure monitoring system) * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3 m warning panel sets at front and rear Djdsv D Tbdopfx Ag Tjul * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting B-dimension of approx. 8,080 mm) * Support winch at front * Outward-folding rear supports * Plastic toolboxes approx. 750 x 350 x 300 mm, mounted left & right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED lighting system 12/24V * 2 additional LED reversing lights at the rear (activated via reverse gear) * 1 removable LED beacon (including bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m external container width) and lockable, lock dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) for an overall width of 3,000 mm * Perforated outer frame bent at approx. 45 degrees with 2 t lashing capacity every 480 mm, possible installation of 3 t drop lashing rings every 600 mm - 5 x 3 t UVV lashing rings mounted on each side; at front and rear corners, each 1 x 6.3 t lashing ring (front directly behind container locks in the floor and rear in the end cross member), various bores for 1.2 t lashing points in front wall and end cross member * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Storage compartment below loading area embedded in chassis, accessible from rear * --- Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized --- * Axles, air tanks, front support winch, and flange eye painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from KW 09/2026

Durumu: yeni, azami yük ağırlığı: 30.740 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * Smard board for payload determination * Warning panel packages front & rear * Reflective contour tape on sides and rear * Rotating beacon (removable) at rear * LED lighting * Straight drawbar with 50 mm towing eye and continuously adjustable height * Toolbox made of powder-coated steel plate and spare wheel holder in basket design, right side * Closed plastic single mudguard at the front * Rear straight steel mud flaps each with spray suppression * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. lids, lockable * Chassis made of high-tensile fine-grain steel * Floor over turntable platform made from 50 mm and in low-loader platform made from 60 mm coniferous timber * Outer planks of the ramps made from hardwood * Four stake pockets on each side (stakes not included), each with simultaneous 2 t lashing point * Load securing package including: 2 lashing rings 6.4 t at the front left and right on the main frame of the turntable platform * On the outside frame, 2 pairs of lashing rings 13.4 t front and rear, as well as 4 pairs per side of 10 t folding and lowering lashing rings * Loadable in all directions and integrated into the outer frame * 2 pairs of 6.4 t lashing rings at the excavator arm rest on the side * 8 pairs of galvanized folding extensions for 3 m overall width (not in the rear slope) * Widening boards stored on the left side in a storage compartment * Excavator arm rest above rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical rear stabilizers * Hydraulic folding ramps with hydraulically extendable ramp end approx. 4,650 x 720 mm incl. hydraulically lateral ramp shift & load holding valve * Loading area above fifth wheel: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height when loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm rear slope) * Flow divider installed * Chassis, turntable, ramps, folding outriggers, and mechanical stabilizers hot-dip galvanized * Axles, drawbar, air tanks, and fifth wheel painted black * Tires: 235/75 R 17.5 * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale * Available from CW 07/2026 Dsdpfxol Tphrs Ag Teul

Durumu: yeni, azami yük ağırlığı: 38.290 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2025, * TS 3 Profile 30.0: * Wabco EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco Plus axles * Air suspension with lifting and lowering device as well as RtR valve * Rear axle self-steering with electro-pneumatic steering lock * Smartboard control box mounted on the trailer as an info tool with pressure sensors for total axle load display * Side underrun protection * Landing legs at the front and mechanical swing-down supports at the rear of the chassis * 15-pin electrical connector * LED lighting system 12 / 24V * Removable LED beacon at the rear left * Mechanically adjustable warning sign sets at front and rear * Straight steel mudguards * Spare wheel carrier under chassis, right side * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm aluminum side boards (RAL 9010 pure white), foldable and removable, on the fifth-wheel platform * Rear wall, inserted -150 mm- high * Rear slant on the fifth-wheel platform to the lowbed, approx. 700 mm long * Fifth-wheel platform with 50 mm wooden planks and lowbed platform with 60 mm wooden planks * Tread plate above the axles * 8 x mechanical fold-out extensions to 3 m total width, except in the rear slope (extension planks available with storage on the fifth-wheel platform) Dsdol Tnvgjpfx Ag Toul * Lashing package: on the fifth-wheel platform 2 x 6.3 t lashing rings each as well as 3 x 5 t lashing bars per side in the outer frame, on the lowbed platform 2 x 13.4 t lashing rings per side as well as 4 x 10 t lashing rings, swiveling and lowerable, recessed in the outer frame, 2 x 6.4 t lashing eyes per side as well as a rear lashing ring in the excavator arm trough * Excavator arm trough extending from the end of the last rigid axle across the steering axle up to the rear cross member with internal reinforcement profiles, approx. L = 2,450 x W = 770 mm x D = 270 mm * 2 x container locks directly after the drop in the lowbed platform * Mechanically single-piece hot-dip galvanized hydraulic access ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for future customer-side retrofitting of hydraulic ramp shifting * The outer plank on the ramp consists of 50 mm hardwood * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck above 40 l/min up to 120 l/min) * Loading area of the fifth-wheel platform: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm transition slope) * Coupling height approx. 1,220 mm (suitable for 2- and 3-axle tractor units) * Chassis, access ramps, rear swing-down supports, extension consoles hot-dip galvanized * Axles, landing legs, air reservoirs painted in black * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 16/2026

Durumu: yeni, azami yük ağırlığı: 5.840 kg, toplam ağırlık: 8.800 kg, dingil konfigürasyonu: 1 dingil, Üretim yılı: 2025, * KWH 8.8 ML: * RDC Tire Pressure Monitoring System * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Front landing gear * Spring-assisted square tube rear supports with baseplates and safety locking pins for multiple support heights * Drawbar with 40 mm bolted towing eye (height-adjustable, mm) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel mudguards with splash protection * Enclosed side underrun protection, usable as advertising space * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm * Swiveling cable drum superstructure; clear width between drum arms 1,700 mm — with tension lock for drum securing at the carrier arm ends as well as a central claw lock for securing the cable drum superstructure to the chassis * Motor-hydraulic drum drive with hydraulic motor * Valves and movable, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive Dsdpfxeu I Iq Ee Ag Tsul * Steel drum shaft with 76 mm diameter, centering and rotating ends * 1 pair of polyamide centering cones, stepped design * Hydraulic pump unit with diesel engine * Fuel tank and hand starter * 6.5 HP with gear pump (150 bar) * Finish: Hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 13.700 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TRA 18.0: * 2-in-1: Suitable for roll-off containers and as a low-loader * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10-ton axles * Air suspension with manual rear lowering * Drawbar 2,000 mm long with 40 mm towing eye and adjustable height mechanism * Tool box made from powder-coated sheet steel approx. 1,000 x 300 x 600 mm, plus spare wheel holder in basket design on right side * Reflective contour markings on sides and rear * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumper pads * Foldable "A" warning sign at the rear * LED tail lights * 15-pin power connector * Main frame with raised outer rails to guide roll-off containers * Steel floor plate with wheel recesses in the bogie area * Container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking system and mechanically pluggable front stop angles on the runway, load securing certificate according to DIN 30722-1 * Load securing package including: 1 pair 10-ton UVV lashing rings on the front end beam, 3 pairs 10-ton UVV lashing rings on the side outer frame, 4 x 2-ton lashing eyes per side in cloverleaf design, 4 x 8-ton lashing brackets recessed in outer frame * Weld seam as anti-slip coating in the ramp area * Rear mechanical drop-down supports * 1 pair aluminium ramps (10.6 tons/pair), 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment at the rear) * Chassis, bogie, locking parts, rear drop-down supports hot-dip galvanized * Drawbar, axles, and air tanks painted in black * New vehicle without initial registration with full manufacturer's warranty * Errors and prior sale excepted * Available from week 05/2026 Duodpfxjl Tq Nmj Ag Tol

Durumu: yeni, azami yük ağırlığı: 10.360 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 14.4: * TPMS (Tire Pressure Monitoring System with in-cab display via EBS signal, no truck-side installation required) * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * Drum brakes * Gigant axles * Air suspension with lifting and lowering function * Height-adjustable drawbar, approx. 300 mm * JOST landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox, front right, mounted externally on the front bulkhead * Side underrun protection * Plastic quarter mudguards * LED lighting system * 15-pin electrical connector * Hot-dip galvanized chassis, drawbar, front wall, and rear wall * 50 mm softwood floor * Pre-installed fittings for retrofitting 20'' container locks at front and rear * Bolted smooth sheet metal front wall * Fold-down steel side walls – trapezoidal profile – with drop-side spring-assist * Bolted, hot-dip galvanized rear stanchions * Perforated outer frame, approx. 45-degree angled, with 2 t lashing capacity every 480 mm; installation of 3 t folding lashing rings possible every 600 mm; 1 x 6.3 t lashing ring at each front and rear corner; multiple bores in front and rear crossmembers for 1.2 t lashing points * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles, stowed in compartment under the load area at the rear of the chassis * Vehicle hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf Dsdjndpn Sepfx Ag Tjul

Durumu: yeni, azami yük ağırlığı: 31.630 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring system with indication option in the truck via EBS signal – no truck-side installation required * Warning sign package at front and rear * Reflective contour marking strips on the sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED rotating beacon * 24 V 15-pin power cable and additional 12 V 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm draw eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in basket design, right side * Front enclosed single plastic mudguards * Rear straight steel mud flaps, each with spray suppression (anti-spray design) * Side underrun protection * Extended offset neck, 500 mm forward * Turntable platform extended by 520 mm at the front with 45° corners, 3 integrated lockable storage compartments with covers * Chassis made from high-strength fine grain steel * Floor over turntable platform made of 50 mm softwood, lowbed platform made of 60 mm softwood * Outer planks of the loading ramps made from 50 mm bamboo wood * Four stake pockets each side (stakes not included), each with 2 t lashing possibility * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the turntable platform, one pair 13.4 t lashing rings each front and rear side on the outer frame, four pairs each side of 10 t swiveling and lowerable lashing rings, loadable in all directions and recessed in the outer frame, two pairs 6.4 t lashing rings on the excavator arm recess, 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear end slope) * Extension planks stored in a side compartment on the left * Excavator arm recess over rear axle to end of ramp slope approx. 2,300 x 740 x 190 mm * Mechanical fall supports at the rear Dujdpfx Ael Th Evog Tsl * Hydraulically galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic side ramp shift on sliding pipe from ramp shaft * Loading area over turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Laden loading height approx. 860 mm (including 860 mm ramp slope) * Chassis, turntable, loading ramps, mechanical rear folding supports hot-dip galvanized * Axles, springs, air tanks, and turntable painted in black tone * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from calendar week 46 / 2025

Durumu: yeni, azami yük ağırlığı: 10.900 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring System) * EBS electronic braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension * Height-adjustable tow bar by approx. 300 mm; tow bar extension by 250 mm to 2,250 mm * Jost landing gear at the front * LED tail lights * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox, front right side, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis as well as tow bar, bulkhead, rear wall, tailgate, and loading ramps * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Drop side walls made from trapezoidal-profiled steel sheet, foldable with drop side spring assist * Steel rear wall, can be stored between ramps; holder for unused rear wall inside at the bulkhead * Bolted rear stanchions * Perforated outer frame, approx. 45-degree bent, with 2 t lashing capacity every 480 mm; optional installation of 3 t recessed lashing rings every 600 mm; each corner at front and rear with one 6.3 t lashing ring; various holes for 1.2 t lashing points in bulkhead and rear crossmember * Single-piece mechanical grating ramps with spring system for one-man operation, approx. 2,750 x 600 mm (retractable to 20 mm) * Rear approach angle approx. 860 mm * -- Reinforced and certified body to EN 12642 XL, including load-securing certificate -- * Drop side color in RAL 9010 pure white * Painting of side walls in RAL color of your choice available at extra cost Dusdpjpk Dv Rofx Ag Tol * New vehicle with manufacturer’s warranty * Errors and interim sale excepted * Available immediately from Egestorf

Durumu: yeni, azami yük ağırlığı: 14.660 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 19.0: * Wabco EBS braking system Dujdpfsl Th Hlex Ag Tsl * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem equalizing gear * Drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * External folding support legs at the rear * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood flooring * Preparation in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Side walls made of trapezoidal-profiled steel plate, foldable with drop side spring lift * Steel rear wall insertable between the ramps – storage mount inside the front bulkhead when not in use * Bolted rear stanchions * Perforated outer frame approx. 45 degrees bent with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * In each front and rear corner, 1 x 10 t lashing ring; various holes in the front and rear cross members for 1.2 t lashing options * One-piece mechanical grating loading ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, loading ramps and folding supports hot-dip galvanized * Drop sides painted in RAL 9010 pure white * Optional painting of side panels in other RAL colors possible for an extra charge * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 37.500 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2024, * TS 3 RM 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW axles * Air suspension with lift/lower device and Ride-to-Release valve * Last axle self-steering with electro-pneumatic steering lock * Side underrun protection * Landing gear at front and swing-down supports at rear of chassis Dusdjl Tiiyopfx Ag Tol * 15-pin electrical connector * LED tail lights * Mechanically adjustable warning panel sets, front and rear * Rotating beacon (removable) at rear left * Straight steel sheet fenders * Spare wheel holder in front of bulkhead cross member (without spare wheel) * Saddle platform with front corners chamfered at 45° and front toolbox made of galvanized, powder-coated sheet steel, W = 2,480 mm x H = 500 mm x L = 665 mm, with hinged lid * 400 mm aluminum side panels (RAL 9010), fold-down and removable, mounted on sides of the saddle platform * Rear wall inserted, height 150 mm * Rear slope on the saddle platform to the low bed approx. 700 mm long, each with 1 recessed lashing ring * Saddle platform with 50 mm clamped hardwood planks and low-bed platform with 60 mm clamped hardwood planks * Tread plate above the axles * 9 x mechanical folding extensions to 3 m overall width (no extensions in rear slope area); extension planks supplied with enclosed transverse stowage compartment under the loading area * 2 lashing bars recessed into the outer frame of the saddle platform on each side; 3 lashing rings per side in the low-bed platform plus 1 additional centered lashing ring at the rear cross member; 2 x 5 t lashing rings per side, bolted at the lower outer frame of wheel recesses * 2 x 6.4 t UVV-compliant lashing rings per side in the excavator arm trough * Excavator arm trough runs continuously from the end of the last rigid axle over the steering axle to the rear cross member, with internal reinforcement, approx. L = 2,450 mm x W = 770 mm x D = 270 mm * 2 wheel recesses per side, 390 mm deep and 640 mm wide, with slide-in covers for transporting wheel loaders with wheelbases from 3,120 - 3,620 mm; front recess slopes up from 1,100 mm at the bottom over a length of 2,050 mm, rear recess slopes up from 580 mm at the bottom over a length of 1,550 mm * Hydraulic folding ramp with extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic lateral ramp adjustment * Outer board on the ramp made of 50 mm hardwood * Load area above turntable: approx. 3,950 x 2,480 mm * Unladen loading height: approx. 1,470 mm * Lower loading area: approx. 8,500 x 2,520 mm * Unladen loading height: approx. 910 mm (including 860 mm ramp slope) * Chassis, rear swing-down supports, ramps, mechanical folding extensions are hot-dip galvanized * -- Axles, springs, air tanks painted in black tone -- * Suitable for 2- and 3-axle tractor units * Coupling height: approx. 1,220 mm * Tires: 235/75R17.5 * Technically permissible gross weight: 48,000 kg * Vehicle is hot-dip galvanized * Side panel painting in RAL 9010 pure white * Other RAL colors for the side panels available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 10.500 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lift and lowering system * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * 15-pin power connector * LED lighting * Front support winch * Rear external foldable supports * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provision for subsequent installation of 20'' container locks in front of the bulkhead and at the rear * Bolted smooth sheet metal bulkhead * Side walls made of trapezoidal-profiled steel plate, folding, divided once in the middle * Steel rear wall, retractable between ramps, bracket for storage inside at the front when not in use * Rear stakes bolted * Perforated outer frame, angled approx. 45°, with 2 t lashing capacity every 480 mm * Installation of 3 t lashing rings possible every 600 mm – 4 lashing rings installed on each side * Each front and rear corner with 1 x 6.3 t lashing ring * Various holes in the front and rear cross members for 1.2 t lashing options * One-piece mechanical grating loading ramps with spring system for one-man operation, approx. 2,750 x 600 mm (retractable to 20 mm) Djdpfx Ajl Thvxjg Tsul * Rear entry angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, springs, air tank, flange towing eye and support winch painted in black * Side wall color freely selectable up to approx. 2 weeks before production date, but no metallic or special colors * -- Reinforced and certified body according to EN 12642 XL incl. load securing certificate -- * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available, Egestorf

Durumu: yeni, azami yük ağırlığı: 31.000 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.290 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 950 mm, * PT 40.0 Profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering system, including RtR valve * Manometer pressure gauge for load weight determination (axles separated into two air suspension circuits) * Side underrun protection * Swing-out support legs at the rear of the chassis frame * Mechanically adjustable warning sign kits at front and rear * Front axle: plastic quarter mudguards with splash protection * Rear axle: straight galvanized steel mud flaps with splash protection * Reflective contour tape on sides and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12 / 24 V * Removable LED beacon at the rear * 2 LED reversing lights (activated via reverse gear) * Drawbar with 50 mm towing eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Extension in front of the turntable platform, approx. 490 mm long with 45° corners Duedpsl Tnu Ajfx Ag Tsl * Robot-welded anti-slip covering on the steel plate of the turntable platform * Load securing package consisting of: in front of the bulkhead carrier left & right each 1 x 13.4 t UVV lashing ring, on each side 4 holes in the turntable platform with 2 t lashing force each, 1 pair of lashing rings (13.4 t) suspended at the rear left & right in front of the rear cross member, on each side 4 pairs of swiveling and lowerable UVV lashing rings (10 t), loadable in all directions and recessed in the outer frame, on each side 3 stake pockets with simultaneous 2 t lashing possibility * Hot-dip galvanized mechanical fold-out extensions for 3 m overall width (not in the rear slope area) * Plank holder for extensions under the chassis left, longitudinal orientation * Excavator stick rest, from rear axle up to the end cross member, approx. 2,100 mm long and approx. 190 mm deep, on each side 2 pairs of 6.4 t lashing rings in the excavator stick rest * Hardwood flooring on the running surfaces of the low loader platform * Hydraulically operated single-piece loading ramps (approx. 3,000 x 720 mm), mechanically laterally adjustable * Outer planks of the loading ramps made of hardwood * Steel structure pre-manufactured for 6-way control valve * Loading edge height unladen approx. 950 mm +/- 20 mm chassis * Turntable, fold-out extensions, mechanical supports, loading ramps all hot-dip galvanized * --Axles, air tanks, drawbar painted in black-- * Tyres: 235/75 R 17.5 * The vehicle has a day registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 23.700 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2024, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system (TPMS) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge for load weight determination (axles separated on 2 air suspension circuits) Duodpfx Agel Tq Euj Tsl * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle with closed plastic fenders, rear axle with straight, galvanized steel splash guards, each with spray protection * Reflective contour marking tape on sides and rear * Hinged lid (hot-dip galvanized) for the toolbox in the turntable platform * LED taillights * Removable rotating beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring and turnbuckle * 2 x 7-pin electrical sockets * Four stake pockets per side, each with 2 t lashing possibility * Load securing package consisting of: 2 lashing eyes (6.4 t) at front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant lashing rings, swiveling and lowerable, loadable in all directions and integrated into the outer frame – 13.4 t at the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for a total vehicle width of 3 m (not in the rear slope) * Widening planks stored in the center of the loading area * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm), laterally adjustable * Loading area above turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm drive-up slope) * Chassis, turntable, drawbar, folding widenings, and ramps hot-dip galvanized * Axles, turntable, air tanks, etc. painted in black tone * Tires: 235/75 R 17.5 * Payload approx. 24,000 kg with a total weight of 30,000 kg * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 16.400 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as an information tool on the trailer, with pressure sensors for axle group load indication * Side underrun protection * Mechanically adjustable warning sign boards at the front and rear * Front axle: closed plastic mudguards; rear axle: straight galvanized steel skirts, both with splash protection * Foldable (hot-dip galvanized) cover for the toolbox in the turntable platform * Toolbox made from galvanized sheet steel, approx. 650 x 300 x 600 mm (black powder-coated), mounted on right side * 15-pin electrical connector * LED lighting, 12 / 24 V Dsdpfx Agstplv Ns Toul * Removable LED beacon at rear * Side marker lights with indicator control * Towing bar with 40 mm towing eye, height adjustable via tension spring and turnbuckle * Tire pressure monitoring system with in-cab display via EBS signal (no installation required on the truck) * Rubber lining on the folding ramps and on the left and right drive-up slope (approx. 860 mm long) * Rubber lining on longitudinal members from bulkhead to end crossmember * Hardwood flooring on the running surfaces of the low-bed platform * 4 stake pockets per side, each with 2 t lashing capacity * Load securing package consisting of: 5 pairs of UVV load rings, swiveling and retractable, loadable in all directions and recessed into the outer frame - corners rated to 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the sloped rear section) * Timber support holders under loading platform in longitudinal direction * Raised roller stop in front of the bulkhead, with 1 x 6.4 t lashing ring on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically deployable ramp tip and load-holding valves * Hydraulic lateral ramp adjustment * Rear hydraulic support (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck from over 40 l to max. 140 l / min) * Hydraulic control block, splashwater protected * Dual-line hydraulic system * Platform above turntable: approx. 1,960 x 2,520 mm * Rear loading platform: approx. 6,500 x 2,520 mm (including 860 mm approach ramp) * Loaded platform height: approx. 890 mm +/- 20 mm (air suspension adjustment) * Chassis, turntable, roller stop, folding extensions, and access ramps hot-dip galvanized * Axles, turntable, drawbar, air tanks, etc. painted black * Loaded platform height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 8.620 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2024, * KA-TA-R 11.9: * 5.5-meter platform body fully finished in RAL 9010 pure white * Tire Pressure Monitoring System (TPMS) * Electronic Brake System (EBS) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 5.5 t Gigant axles * Parabolic springs with tandem equalization unit * Height-adjustable (by 300 mm) hot-dip galvanized towing bar with 40 mm flanged towing eye * Jost mechanical support winch at the front * Two mechanical hot-dip galvanized folding supports at the rear * Galvanized steel toolbox, mounted right side * 15-pin electrical plug * LED tail lights * Hot-dip galvanized bolted underride guard * Galvanized steel toolbox, mounted right side * Plastic quarter mudguards Dodpfx Aem Angvog Tsul * Mesh hooks on the sides and at the rear located at the central locking mounts, plus three on the front wall * Hot-dip galvanized chassis * Steel pallet cage body, tipper on three sides * Continuous side panels without central stanchions, foldable with board side spring-lifters * Tailgate can be folded down and also swung, with manual central locking * Hot-dip galvanized screw-in rear stanchions * Each corner equipped with one 5 t lashing ring; four 3 t lashing rings recessed on each side in the outer frame * 4 mm steel plate floor * Mounting rail at rear for loading ramps * Prepared for later installation of side wall extensions * Reinforced body with load securing certificate to EN 12642 XL * One pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment at the rear integrated into the chassis below the loading area * Axles, springs, air tanks, towing bar and support winch all painted black * Platform body color: RAL 9010 pure white * Painting of the side panels and tipping platform in any RAL color available at extra cost * Tyres: 235/75R17.5 * Wheelbase: 990 mm * New vehicle, unregistered, with manufacturer's warranty * Subject to error and prior sale * Immediately available ex works Egestorf, A7

Durumu: yeni, azami yük ağırlığı: 16.000 kg, toplam ağırlık: 21.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 700 mm, Üretim yılı: 2024, * KA-TA-RT 21.0 ML: * Without ABS / EBS, approved for 40 km/h * Spring-loaded parking brake, drum brakes * Gigant axles * Tandem equalization system with 100 mm wide parabolic springs * Support winch at the front * Mechanical drop-down supports at the rear * Fixed, welded-in drawbar with a low-maintenance K80 ball hitch (adjustable by +77 mm / 33 mm via head plate), with raised bracket for connection lines * 12 V 7 + 4 pin electrical wiring * LED lighting system 12 / 24 V with protective grilles * 2 LED work lights at the rear, switchable from the towing vehicle without installation on the towing vehicle * Side marker lights with indicator activation * Plastic quarter mudguards * Plastic toolbox approx. 750 x 350 x 300 mm, right side * Chassis made of fine-grain steel * Steel pallet 3-way tipping body with M-Strong side walls (fixed front wall, continuous side walls - without central stanchions - swinging on mechanical central locking and mechanically foldable with drop-side spring lift) * Hydraulic tailgate, 500 mm high, acts as hydraulic chute with a 115° opening angle * 4 mm Hardox 450 steel floor * Lashing rings: 1 x 7 t in each corner, plus 4 x 3 t each side, recessed and foldable * Hot-dip galvanized 2-step access in front of the front wall (on driver’s side left) Dsdpfx Ajr Dpz Hog Tjul * 1 pair aluminum loading ramps (10 t / pair with axle spacing over 2,500 mm), 3,570 x 410 x 120 mm, suitable for rubber-tyred and tracked vehicles * 2 ramp storage compartments at the rear, integrated into chassis; load securing according to EN 12642 XL * Coupling height loaded approx. 530 mm, unloaded approx. 590 mm * Bodywork painted in RAL 9010 pure white * Chassis, drawbar, rear drop-down supports and underride protection all hot-dip galvanized * Axles, air tanks, front support winch * K80 hitch painted in black * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf