Kullanılmış Fliegl Dts Fragmanlar satın al (309)

Durumu: yeni, makine/araç numarası: 535119ca408d3bd5a8e74be51, boş ağırlık: 6 kg, azami yük ağırlığı: 11 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Low-loader Trailer Welded steel construction Turntable with heavy-duty ball bearing slewing ring, tool box recessed in the turntable frame Foldable rear support Wheel chocks with holders Aluminium side underrun protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray mudflaps behind each axle 1 plastic toolbox with shelf, w=620/h=360/d=440 mm, lockable with padlock (lock not included) Extendable deck widenings to 3,000 mm (not in rear chamfer) (the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm), central compartment for timber planks on the loading area, 70 mm planks for widening to 3,000 mm Iijdpfx Aoi Ri N Hog Nja Lashing Points Low-loader 3 pairs of 10 t lashing points integrated in the floor at the front 6 pairs of lashing mushrooms, 10 t each, recessed at the top and side in the outer frame 1 x after gooseneck, remaining distributed in between, spacing not greater than 1,200 mm 1 x rear chamfer 5 pairs of ring lashing eyes in the outer frame, 5 t each (instead of stake pockets) Trailer Drawbar Assembly - Turntable trailer Drawbar with tested 40 mm towing eye Axles & Suspension SAF drum brake axles Axles/chassis laser measured to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tyres 235 / 75 R 17.5 As per manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 interchange-proof coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS plug at the front, with connecting cable Note: This trailer may only be towed by tractor units that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lights, yellow LED side markers 2 white/red lane marker lights at the rear 2 white position lights at the front 1 revolving beacon with holder, switchable via parking light (beacon removable) 2 pairs of warning signs, double LED illuminated, extendable to 3,000 mm 2 x 7-pin interchange-proof plugs at the front, with connecting cable Deck Front section with steel floor, then 70 mm softwood floor, wheel arch areas with steel/chequer plate covering Rear chamfer with 70 mm softwood floor Low-loading area incl. rear chamfer 8,200 mm Access Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Additional foldable ramp lock at the bottom (prevents side slippage of ramps, not in combination with hydraulic side ramp adjustment) Wood covering Assisted by spring lifters Operating Notes Special permit is required for 10,000 kg axle load. Permit must be applied for individually in each federal state; the legislator is not obliged to guarantee a permit for 20 t GVW. Customer's responsibility. The specified total weight is technically possible, depending on the load, the permissible gross weight may not be achievable due to axle/support/saddle load restrictions. Registration / Plates Country of registration: Germany Test approval according to EC 2007/46 24/7-Service Hotline Prepared for two-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Warning sign according to ECE - 70 Paintwork Frame: DB Novagrau Ramps: hot-dip galvanised Note: Archive photos!

Durumu: yeni, makine/araç numarası: d0373d7a64f0aead858df4eb5, boş ağırlık: 2.621 kg, azami yük ağırlığı: 15.379 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 385/55 r22.5, Further Information Chassis with Swap Body Turntable Fine-grain steel welded construction Fliegl V-Stream frame Front stop, longitudinally adjustable and foldable Pair of guide rollers removable, front and rear 4 container locks with solid outriggers on 20-foot base for swap bodies 7.15 and 7.45 Turntable with heavy-duty ball bearing slewing ring Wheel chocks with holder Iiedpfx Asi Ri Rgog Nea Side underrun protection aluminium (Fliegl standard) Side underrun protection fitted inward, for optimal clearance to swap body supports Rear underrun protection, steel (Fliegl standard) Rear underrun protection shortened for optimal clearance to swap body supports, light units mounted protected Half-shell mudguards (Front, where technically feasible, otherwise with sheet metal cover + quarter-shell mudguards) With anti-spray flaps behind each axle Rubber rear-end buffer Drawbar trailer turntable coupling Drawbar with certified 40 mm towing eye Parking sockets for electrics/ABS on drawbar Brake/electrics terminal plate on drawbar, EBS and electrics removable, all connection lines to towing vehicle as spiral flex hoses Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Air suspension Brake System 2-line compressed air brake system Coloured line routing for easier servicing Air reservoir 208 litres Spring-loaded parking brake Duomatic connection at front, with connecting line to truck, spiral cable EBS by Wabco, electronic braking system with EBS plug at front, with removable spiral connection cable Attention: The trailer may only be towed by vehicles that ensure the ABS function! With raise & lower valve, hold function in both raised/lowered positions + auto-reset function, quick release valves on all axles Vehicle Stability Control System Axle load detection via EBS CAN-bus signal, for display in the driver’s cab, truck must be pre-equipped accordingly, no calibration/legal weighing system installed Wheels and Tyres 385/55 R22.5, brand at manufacturer’s discretion Steel rims, factory silver Electrics 24 Volt, multi-chamber LED tail lights with resistor, side yellow LED lights, LED licence plate illumination (note: on certain towing vehicles, fault diagnostics may occur despite function) 2 white LED position lights at front 2 white/red LED lane marker lights at rear 1 x 15-pin plug at front, with removable spiral connection Additional LED work lamps at the rear, switched via reverse light LED work lamp front centre between chassis beams, rear-facing, switched via reverse light Registration Country / Plates Germany With manufacturer’s confirmation + brake calculation 24/7 service hotline Prepared for single-line number plate holder Warning plate to ECE-70 Contour marking with reflective tape to ECE R048, white side and red at rear Paintwork Frame DB 7350 Novagrau 10-year warranty against rust-through Attention: Archive pictures!

Durumu: yeni, makine/araç numarası: 9de849c07b4d917b8d8e1d037, boş ağırlık: 2.990 kg, azami yük ağırlığı: 15.010 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 265/70 r19,5, Further information Chassis Swap Turntable Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-foot base for swap bodies 7.15 and 7.45 meters Turntable featuring a robust ball bearing slewing ring Wheel chocks with holders Aluminum side underrun protection Side underrun protection set inward for optimal clearance to swap body supports Steel rear underrun protection Shortened rear underrun protection for optimum clearance to swap body supports, lighting system mounted in a protected position Quarter-shell mudguards at the front and half-shell mudguards at the rear Coupling device for turntable trailer Drawbar with tested 40 mm towing eye Drawbar mechanically length adjustable in 6 x 100 mm increments (approx. 1700 – 2300 mm), drawbar length currently set to 2200 mm Axles & Suspension SAF disc brake axles Geometry/alignment of axles and chassis by laser to minimize tire wear and reduce fuel consumption Air suspension Brake System 2-line compressed air braking system with color-coded lines for easy servicing Air reservoir 180 liters Spring-loaded parking brake 2 error-proof coupling heads at the front, with connecting lines to the truck EBS by Wabco, electronic braking system with EBS socket at the front, with connecting cable Iedpfji Ri Rnsx Ag Neia Note: The trailer must only be towed by tractor units that ensure ABS functionality! With lift & lower valve, holding function in both raised and lowered positions Wheels and Tires 265/70 R19.5, manufacturer as specified by OEM Steel twin wheels, factory silver Electrical System 24 Volt, multi-chamber LED lights with resistor, side amber LED lighting, license plate illumination in LED (note: some tractor units may display error messages, although functionality is assured) 2 white LED position lights at the front 2 white/red lane marker LED lights at the rear 2 x 7-pin error-proof plugs at the front, with connecting cables Additional LED work lights on both sides of the rear, operated by the reversing light Central front-mounted LED work light between support beams, rear-facing, operated by the reversing light Registration/Country & Plates Germany With Dekra inspection and certificate (per §13 EC-FGV) 24/7 service hotline Incl. loading for 2/3 stack, loading racks against deposit Prepared for single-line license plate holder Contour marking with reflective tape in accordance with ECE R 048, white on the sides and red at the rear Painting Frame DB 7350 Nova Grey 10-year anti-perforation warranty Note: Archive images!

Durumu: yeni, makine/araç numarası: eca976917d325d4adc41b69e8, boş ağırlık: 7.200 kg, azami yük ağırlığı: 27.800 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r 22,5, Further information Chassis semi-trailer for freight forwarding High-strength fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2-inch kingpin, main frame reinforcement for 25 t at the center of gravity over 3 m loading length when retracted. 13 pairs of hooks for lashing strap attachment welded to the crossmembers 23 pairs of lashing rings recessed into the outer frame, each rated for 3.5 t Outer frame with load-lock profile for lashing strap attachment Note! Not usable with side walls! 24 t 2-speed landing gear in reinforced version for unhitching while loaded, single-sided operation, with semi-circular lower section and straight mounting plate, with thrust compensation Wheel chocks with holders Aluminum side underrun protection Rear underrun protection Half-shell mudguards With anti-spray mud flaps in accordance with EU regulations 1 spare wheel carrier for 1 spare wheel, with wheel fastening kit 1 stake storage box, closed at the sides, open at the top, below the loading area, doors on both sides, W=450 mm/H=400/420 mm/D=2460 mm 6 pairs of extendable stake pockets for square tube stanchions 80x80 mm, extendable from loading width 2000 mm to 3100 mm 4 pairs of stake pockets recessed in the outer frame for square tube stanchions 80x80 mm 11 stake pockets centrally recessed in the floor for square tube stanchions 80x80 mm, with reinforcement beams, installed between the outer stake pockets Isdpfx Aji Ri Szjg Nsia 5 x 3 pairs of stake pockets on the outer longitudinal beams for square tube stanchions 80x80 mm, including reinforcement beams – for load securing to the front and rear during transport of reinforcing steel mesh, 2x5000 mm or 2x6000 mm 6 lightweight plug-in stanchions W=80/D=80 mm, usable height approx. 1850 mm, hot-dip galvanized, top with cable guides for strap tensioning 12 lightweight plug-in stanchions W=80/D=80 mm, usable height approx. 1850 mm, hot-dip galvanized with lashing rings welded to both sides at the bottom Note: Stake pockets/plug-in stanchions are not designed for sole securement of long materials, pipes, etc. without additional lashing 2 plastic tool boxes, with drawer and shelf, W=650/H=520/D=670 mm, lockable with a padlock (lock not included) 6 reinforcing steel winches with wire cable and counter hook, with cable feed-through in the outer frame, 1 removable plug-in gearbox for reinforcing steel winches supplied loose (without frame mounting) Telescoping Main frame telescopic, extendable by max. 4000 mm and lockable at approx. every 500 mm Locking with pneumatic bolt locking + frame locking indicator on both sides, operation via manual button, control for brake/locking and suspension on driver’s side, ahead of the axles Storage compartment between longitudinal beams when extended Axles & Suspension SAF disc brake axles with 430 mm disc diameter Rear axle is self-steering, with automatic reverse lock via reversing light, with additional lock function on the trailer via hand button, and manual override in the tractor unit (pin 10), no truck installation required. Offset axle spacing mm Air suspension 1st axle with automatic lift, also electrically controllable from the truck, with starting aid, no truck installation required (starting aid functional up to 30% axle overload and max. speed of 25 km/h) Brake System 2-line compressed air brake system Color-coded line routing for easy servicing Spring-actuated parking brake 2 error-proof coupling heads at the front, without connectio

Durumu: yeni, makine/araç numarası: 1acf251a278ec5cde4067a7b1, boş ağırlık: 5.800 kg, azami yük ağırlığı: 22.200 kg, toplam ağırlık: 28.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235/75 r17,5, Further information Chassis Semi-Trailer Forwarder Fine-grain steel welded construction, fifth wheel plate with replaceable 2-inch kingpin Outer frame slightly inclined, new version with load-lock profile for lashing straps 24 t, 2-speed landing gear, operated from one side, straight base, without compensating mechanism Iedpekv Uvzjfx Ag Noia Free landing gear corner dimension or rear swing clearance approx. 1920 mm 2 wheel chocks with holders Side underrun protection aluminium Rear underrun protection steel Quarter mudguards in front of and behind each axle 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 1 plastic toolbox, with shelf, width=620 / height=360 / depth=440 mm, lockable with padlock (padlock not included) Axles & Suspension Drum brake axles, as per manufacturer’s choice Axles/chassis laser-measured to reduce tyre wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, color-coded line routing for easier servicing Spring-applied parking brake Duomatic coupling front, without connecting hose EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that can guarantee the effectiveness of the ABS! With lift & lower valve Vehicle stability system Wheels and tyres 235/75 R17.5, brand at manufacturer’s choice Steel rims, factory silver Electrics 24 volt, multi-chamber tail lights, lateral yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 1 x 15-pin socket at the front, without connection cable Floor Approx. 30 mm thick phenolic resin plywood for high point load capacity, suitable for forklift axle loads up to max. 5,600 kg Front panel / corner posts front 25 mm aluminium hollow section, approx. 1,350 mm high, corner posts steel in volume version Country of registration / plates Germany With DEKRA inspection and certificate (according to §13 EC-FGV) 24/7 Service Hotline Prepared for single-line license plate holder Conspicuity marking with reflective tape in accordance with ECE R 048, white on the sides and red at the rear Paint Frame hot-dip galvanized including passivation, 15-year anti-perforation warranty Front wall aluminium Attention! Archive images shown!

Durumu: yeni, makine/araç numarası: 6650f95fd39bb5625662ee336, boş ağırlık: 7.550 kg, azami yük ağırlığı: 27.450 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/55 r22.5, Further Information Chassis, Semi-Trailer, Long-Haul Transport Fine-grain structural steel welded construction in lightweight design, extending to the landing legs; fifth wheel plate with replaceable 2" kingpin. Side floor prepared for lashing rings (max. 13 pairs) 24 t, 2-speed landing gear, single-side operation, with straight lower section, without shear compensation Rear pull-out ladder Door retainer on the side 2 wheel chocks with holders Side underrun protection in aluminium Underrun guard in steel with wide Fliegl mud flaps; foldable splash guard for lighting units Quarter circle mudguards Rear collision protection bumper Aluminum ladder approx. 3,550 mm, with side holder Tarp pole with bracket 1 plastic toolbox with drawer and shelf, dimensions: w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) 1 spare wheel holder for 1 spare wheel, including wheel fixing kit Axles & Suspension SAF disc brake axles with 430 mm disc diameter Iiedpfji Riwxsx Ag Nsa Laser-measured axles/chassis reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start assist, activation by braking 3x (start assist active up to 30% axle overload and a max. speed of 25 km/h) Braking System 2-line air pressure brake system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS electronic braking system with EBS socket at the front, no connecting cable supplied Note: The trailer may only be towed by vehicles that ensure proper ABS function! With lift and lower valve Vehicle Stability Control System Wheels and Tires 385/55 R22.5, manufacturer at the discretion of the producer Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, no connecting cable SB Hydraulic Hydraulic cylinder with sliding mechanism integrated in the floor. Dual-circuit hydraulics. Forward/reverse motion switching is electric via wired remote control. -Push-floor power supplied via parking lights- Hydraulic operation via truck PTO (power take-off) Hydraulic connection with hose at front wall and HDK screw connector NW = 48 mm Note: A dual-circuit hydraulic system is required! Recommended pump output: Flow rate: 110 ltr/min Pressure: 250 bar Minimum oil tank capacity: 100 ltr SB Floor Moving floor with wear plate at rear Floorboards made of 8 mm ribbed aluminium profile SB Body Aluminum box body made of high-quality, abrasion-resistant material. Front and side walls made from aluminum hollow profiles, fully welded at the top with a wide special reinforcement profile, welded-in special frame at the base. Moving wall for improved discharge of cargo, with reinforced tarpaulin flaps at the bottom. With rail cleaner Rear wall made of aluminum hollow profiles, as double-door (split 1/2 to 1/2), all round fitted with special U-profile with stop and rubber seal, 2 external locking rods, locked at top and bottom. Rear wall has mechanical safety lock, operated at rear, left side in traveling direction. Equipped with swiveling top crossbar. Door locks can be secured by padlock. Standing platform with ladder access on both sides (left/right in direction of travel), with guardrail, for opening/maintenance.

Durumu: yeni, makine/araç numarası: 65c7289da24c6dbb3dde7c971, boş ağırlık: 3 kg, azami yük ağırlığı: 14 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 265/70 r19,5, Further Information Chassis Swap Central Axle Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with robust outriggers on 20-foot base for swap bodies 7.15 and 7.45 1 pair of gearbox support legs at the front, with straight base, individually operable support leg left and right Wheel chocks with holders Side underrun protection in aluminium Rear underrun protection in steel Half-shell mudguards Central axle trailer coupling device Drawbar with certified 50 mm towing eye, forwarding version (not suitable for trucks with tail lift, or detailed inspection required upon order) Iisdpji Rixcofx Ag Nea without adjustable length drawbar Axles & Suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Brake System 2-line compressed air braking system, colour-coded for easy servicing Spring-loaded parking brake Duomatic connection at the front, with interconnection cable to the towing vehicle, connection on front right EBS, Electronic Braking System with EBS plug at the front, with connecting cable, connection on front right Note: The towed trailer may only be towed by vehicles that ensure the effectiveness of the ABS system! with lift & lower valve Wheels and Tires 265/70 R19.5, manufacturer brand at manufacturer's discretion Steel rims in twin arrangement, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red contour marker lights at the rear 1 x 15-pin connector at the front, with connecting cable, connection on front right additional LED work light at the rear, activated by reverse light Front LED work spotlight, centrally mounted between the main beams, rearward facing, controlled by reverse light Operating Notes The specified gross weight is technically possible. Depending on the cargo, the permitted gross weight may not be achievable within the permissible axle, support, and kingpin loads. (Poor driving and tracking performance possible due to incorrect load distribution) Approval Country / Plates Germany with Dekra inspection and report (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour marking with reflective tape according to ECE R 048, side white and rear red Paint Finish Frame DB 7350 Nova Grey, 10-year warranty against rust-through Attention: Archive images!

Durumu: yeni, makine/araç numarası: 562ca26c733cc91276e95b716, boş ağırlık: 6.700 kg, azami yük ağırlığı: 28.300 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/55 r22.5, Further information Iijdpfx Agei Riyws Nja Chassis semi-trailer forwarder Fine-grain steel welded construction in lightweight design, up to the support legs, fifth wheel plate with replaceable 2" kingpin Lashing point preparation in the floor along the sides (max. 13 pairs) 24 t two-speed landing gear, single-sided operation, with straight base, without load equalization Pull-out ladder at rear Door hold-backs on the sides 2 wheel chocks with holders Aluminum side underrun protection Steel rear underrun protection with wide Fliegl mud flaps, foldable splash guard for lighting unit Quarter shell mudguards Rear collision protection Aluminum ladder approx. 3,550 mm, with side mount Tarp pole with holder 1 plastic toolbox, with drawer and shelf insert, w=650 / h=520 / d=670 mm, lockable with padlock (padlock not included) 1 spare wheel holder for 1 E-wheel, with wheel fastening kit Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle / chassis laser alignment to reduce tire wear and fuel consumption Air suspension 1st axle with automatic lift axle, including forced lowering and traction aid, activation by braking 3x (traction aid is functional up to a 30% axle overload and up to a maximum speed of 25 km/h) Brake System 2-line compressed air braking system, colored piping for easy servicing Spring-loaded parking brake 2 unmistakable coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: This towed vehicle may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! With raise & lower valve Vehicle - drive stability system Wheels and Tires 385/55 R22.5 tire brand at the manufacturer’s discretion Steel rims, factory silver Electrics 24 volts, multi-chamber lights, yellow LED side lighting 2 white position lamps at front 2 white/red marker lights at rear 2 x 7-pin and 1 x 15-pin unmistakable sockets at front, without connection cable SB Hydraulics Hydraulic cylinder with sliding device installed in the floor. 2-circuit hydraulic system. Forward/reverse operation switching is performed electrically via cable remote control. Sliding floor power supply via parking lights Operation hydraulically via truck PTO Hydraulic connection with hose on front wall and HDK screw connector NW=48 mm Note: A 2-circuit hydraulic system is required! Recommended pump performance: Flow performance: 110 l/min Pressure: 250 bar Minimum oil tank capacity: 100 l SB Floor Moving floor with wear plate at the rear Floor boards made of aluminum, 8 mm floor profile, grooved version SB Body Aluminum box body made of high-quality, abrasion-resistant material. Front and side walls made of aluminum hollow profiles, all around welded with a wide special reinforcement profile at the top, and with a special welded-in frame at the bottom. Sliding wall for better unloading of the load, with reinforced tarpaulin flaps at the bottom. With rail cleaner Rear wall made of aluminum hollow profiles, as a two-leaf door, split 1/2 to 1/2, framed all around with a special U-profile with stop and rubber seal, fitted with 2 externally mounted locking rods, locked at the top and bottom. Rear wall with mechanical safety lock, operated at the rear on the left-hand side in the direction of travel. With pivoting cross brace at the top. The door locks can be secured with a padlock. Standing platform with ladders on both sides (left/right in the direction of travel) and railing, for opening.

Durumu: yeni, makine/araç numarası: 2dee9cc4124b79c4820f5c3cf, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22.5, Further information Fine-grained steel welded construction, saddle plate with replaceable 2" kingpin, outer frame slightly slanted, new version with load-lock profile for lashing strap attachment, 24t two-speed landing gear, single-sided operation, with straight base, without sliding compensation. Note: Free support leg corner spacing or free swing radius to the rear approx. 1930 mm, pull-out ladder at the rear, side door retainer, 2 wheel chocks with holders, Side underrun protection made of aluminum, rear underrun protection galvanized steel, quarter-shell mudguards in front of and behind the axle assembly, antispray splash flaps according to EC, rear impact protection. SAF disc brake axles with 430 mm disc diameter, axles/chassis laser-measured for reduction of tire wear and fuel consumption, air suspension 2-line compressed air braking system, color-coded piping for easy service, spring-loaded parking brake, 2 non-interchangeable coupling heads at front, without connecting line, EBS (Electronic Braking System) with EBS socket at front, without connecting cable. Attention: The trailer may only be towed by towing vehicles that can ensure ABS functionality! With raise and lower valve, vehicle stability control system. 385/65 R22.5 tires, brand at manufacturer’s discretion, steel wheel rims, factory silver. 24 Volt, multi-chamber tail lights, side yellow LED lighting, 2 white position lights at the front, 2 white/red lane marker lights at the rear, 2 x 7-pin non-interchangeable sockets at the front, without connecting cable. Floor: Anti-slip phenolic plywood panels approx. 30 mm thick, on longitudinal beams for high point load capacity, suitable for forklift axle loads up to max. 7100 kg. Front wall/corner posts: 2580 mm high, corner posts in volume design (steel), unlocking device for side tarpaulin at the front wall, crash blocker, lower inside edge with approx. 140 mm high steel impact guard. Center posts: 3 pairs of sliding posts, adjustable over the entire length, with 4 insert pockets per post and long pocket at the bottom, 3 post positions per side. Insert boards: 5 rows of wooden insert boards. Rear wall/corner posts at rear: rear corner posts steel up to lower roof edge, hook-in for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf, each with 2 internal locking rods. Tarpaulin: tarpaulin with welded horizontal and vertical belts, stainless steel tensioning locks. Iedpfxei Riy Ts Ag Noia Roof: sliding roof, rear end-lift foldable, roof can be pushed from rear to front, L-roof beam for the automotive industry, internal width between roof beams approx. 2490 mm, tarpaulin color: white, 400 Roof non-elastic, minimal deflection of roof beam during loading/unloading, optimal rain gutter at rear on end hoop, above doors. Germany, approval in accordance with EC 2007/46, 24/7 service hotline, Fliegl manufacturer certificate for body stability per EN 12642 XL, prepared for single-line number plate holder, warning sign per ECE-70, reflective stripes: white (continuous along lower edge of side curtain and in upper corners; if visible sideboards, stripe at lower edge of sideboards), reflective stripes: red (surrounding the rear portal). Frame DB 7350 Novagrau, 10-year warranty against rust penetration, landing legs coated black, front corner posts hot-dip galvanized, front wall aluminum, rear corner posts hot-dip galvanized, rear wall white, tarpaulin to RAL as desired, single color and subject to availability. Note: Archive im

Durumu: yeni, makine/araç numarası: 5067caac5acaa655d1d94bd2d, boş ağırlık: 760 kg, azami yük ağırlığı: 1.740 kg, toplam ağırlık: 2.500 kg, dingil konfigürasyonu: 1 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Central axle trailer chassis Fine-grain steel welded construction including 4 mounting points for IBC containers as technically feasible Customer drawing approval required upon order placement! 2 longitudinal beams as double-T sections for later self-supporting body installation, with front cross member 2 pairs of lashing eyes for securing the IBC container Telescopic support foot at the front Wheel chocks with holders Mudguards without side underrun protection Steel underrun protection Central axle trailer drawgear Drawbar with certified 40 mm towing eye, freight forwarding version Drawbar height adjustable via spindle, max. adjustment range 250 mm Axles & suspension GFA or BPW axle, at manufacturer's discretion, with tapered roller bearings and S-cam brakes Axles/chassis laser-aligned to minimize tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mountings Wheels and tires 235 / 75 R 17.5 type at manufacturer's discretion Steel rims in factory silver Brake system 2-line air brake system Spring-loaded parking brake 2 anti-mistake coupling heads at the front, with connecting lines to the towing vehicle, without ABS, but with mechanical ALB (automatic load sensing valve), thus max. 60 km/h road approval Electrics 24 volt, multi-chamber lights, without side yellow LED lighting 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin anti-mistake plugs at front, with connecting cables Country of registration / Plates Ijdji Ri Anepfx Ag Njia Country of registration: Germany with Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline prepared for single-row license plate holder Paintwork Frame: DB 7350 Novagrau 10-year warranty against rust-through Attention! These are archive images.

Durumu: yeni, makine/araç numarası: 1eb6bdba4d54d87ab018b84c2, boş ağırlık: 3 kg, azami yük ağırlığı: 14 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 445/45 r19,5, Further information Chassis Interchangeable Central-Axle Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Removable pair of guide rollers, front and rear 4 container locks with robust outriggers for interchangeable containers, 20-foot base, compatible with swap bodies 7.15 and 7.45 1 pair of gearbox support feet at the front, with straight lower part and single-sided operation on the right (FR) 2 wheel chocks with holder Aluminium side underrun protection Steel underrun protection Half-shell mudguards Splash flaps Central axle drawbar assembly Isdpfx Aei Ri Itjg Neia Drawbar with certified 50 mm towing eye, forwarding version (not suitable for trucks with tail-lift; detailed inspection upon order required) Drawbar without length adjustment Axles & Suspension SAF disc brake axles Axles/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Braking System 2-line compressed air braking system Colour-coded wiring for simplified servicing. Air reservoir: 208 litres Spring-loaded parking brake Duomatic coupling at the front, with connecting line to the tractor unit, connection on front left (FR) EBS, Electronic Braking System with EBS socket at the front, with connecting cable, connection on front right (FR) Note: The trailer may only be towed by towing vehicles which ensure the functionality of the ABS! With lift & lower valve, retaining function in both lift and lower positions Wheels and Tyres 445/45 R19.5, make at manufacturer's discretion Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin polarity-protected connectors at the front, with connecting cable, connection on front right (FR) LED work lights on both sides (switched via reverse light) LED work light front-centred between the carrier beams, rear-facing, switched via reverse light Operating Instructions Special permit required if total train length exceeds 18,750 mm. Country-specific approval regulations must be observed. Country of registration / Plates Germany With Dekra inspection and report (according to §13 EC - FGV) 24/7 Service Hotline Prepared for single-line number plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Paintwork Frame painted DB 7350 Nova Grey 10-year anti-corrosion warranty Note: Archive images!

Durumu: yeni, makine/araç numarası: ee3256d63dd23b3ad1bdf9ab0, boş ağırlık: 10.280 kg, azami yük ağırlığı: 13.720 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Low-bed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Side underrun protection, aluminium Rear spray guards across the entire width Quarter-circle mudguard in front of the 1st axle Excavator arm recess starting above rear axles and running to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t in the excavator arm recess, located on the side of the main frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer 1 storage box recessed in the kink of the floor with lid, W=720 mm / L=520 mm / D=170 mm 1st pair of wheel wells recessed after the frame drop in the low-bed running gear area, with ramped entry, length at the bottom approx. 1,600 mm, approx. 400 mm deep. Note! The main frame is 400 mm higher in this area than the wheel well. 2nd pair of wheel wells between the axles in the low-bed section, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The main frame is 300 mm higher in this area than the wheel well. Removable wheel well covers, insertable from main frame, with timber inserts. Distance from outside main frame beam to beam in wheel well area approx. 1,280 mm Extendable widenings to 3,000 mm, folding at the wheel well extensions (widening not at the rear chamfer and not at the bottom of the wheel wells) (Track width of machinery/vehicles to be transported must not exceed the external frame width of 2,550 mm) Storage compartment for timber planks, centrally on or under the loading surface as per technical feasibility Timber planks 70 mm for widening to 3,000 mm Lashing points for low-bed trailer 1 pair of ring lashing eyes recessed at the front on the frame drop, each rated 5 t 8 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated 10 t 2 x front on frame drop 6 x in the low-bed first lashing eye 250 mm from front and last max. 250 mm from rear, spacing between lashing eyes no greater than 1,100 mm 5 pairs of ring lashing eyes recessed into the outer frame, each rated 5 t (convertible to stake pockets) Drawbar and turntable for trailer Drawbar with certified 50 mm towing eye, towing eye inclined at 8° Axles + Suspension SAF drum brake axles Axles/chassis laser alignment to reduce tyre wear and fuel consumption Iiodpoi Ri I Nsfx Ag Nea Air suspension with independently controllable raise & lower valves at front and rear Wheels and tyres 235/75 R 17.5 Manufacturer’s choice Steel rims, twin-wheel arrangement, factory silver Braking system 2-line compressed air braking system Spring-actuated parking brake Trailer Info Center, displays vehicle data such as axle load (not calibrated) and odometer Axle load detection via EBS-CAN bus signal, display in cab (truck must be pre-equipped accordingly, no truck installation, not a calibrated scale) Vehicle stability system Duomatic coupling at front, with connecting line to tractor vehicle EBS (Electronic Braking System) with EBS connector at front, with connection cable Note: The trailer must only be towed by vehicles that guarantee the effectiveness of the ABS! Electrics 24 Volt, multi-chamber LED taillights with resistor, lateral amber LED lights, licence plate LED illumination (Note: with certain towing vehicles false diagnostics may occur even though functionality is guaranteed) 2 front position lights in LED 2 rear lane marking lights in white/red

Durumu: yeni, makine/araç numarası: 2b58968e34fac93b429a256e9, boş ağırlık: 5 kg, azami yük ağırlığı: 12 kg, toplam ağırlık: 18 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Iijdpfoi Ri Nxox Ag Noa Chassis – Low-bed Trailer - Steel welded construction - Turntable with heavy-duty ball race, storage box recessed in turntable front section - Foldable rear support - Wheel chocks with holders - Aluminum side underrun protection - Full-width rear spray flap - Quarter shell mudguards in front of 1st axle - Spare wheel carrier for 1 spare wheel, with attachment kit - Spare wheel, same brand and specification as base tires, steel rim - Plastic toolbox with insert shelf, dimensions: width=620 / height=360 / depth=440 mm, lockable with a padlock (lock not included) Tie-down Points Low-bed - 3 pairs of lashing points, each rated for 10 tons, integrated into the floor at the front - 6 pairs of lashing studs, inserted in the upper and side outer frame, each for 10 tons; 1 in the gooseneck area, remaining distributed with max spacing of 1200 mm; 1 at rear incline - 5 pairs of ring-type lashing eyes recessed into the outer frame, each rated for 5 tons (convertible to stake pockets) Trailer Drawbar/Turntable - Drawbar with tested 40 mm towing eye Axles & Suspension - SAF drum brake axles - Axles/chassis laser aligned to reduce tire wear and fuel consumption - Parabolic suspension with maintenance-free steel-rubber bushings Wheels and Tires - 235/75 R17.5 - Tire brand at manufacturer’s discretion - Steel twin-mounted rims, factory silver Braking System - 2-line air brake system - Spring-loaded parking brake - 2 reverse-polarity-proof coupling heads at the front, with connecting lines to the towing vehicle - ABS and ALB, with ABS plug at the front, connection cable, voltage converter for 12/24 volt operation Note: A 7-pin 12V socket on the tractor/hauler is required (required for electrics with voltage converter!) Warning: The trailer may only be towed by vehicles that guarantee the effectiveness of the ABS! Electrics - 24 volts, multi-chamber lighting, yellow LED side markers - 2 white/red track lights at the rear - 2 white position lights at the front - Additional LED work light at the rear, operated via reverse gear - 2 x 7-pin reverse-polarity-proof plugs at the front, with connecting cable - 1 x 7-pin agricultural plug - Voltage converter 12/24 volt (for electrics only, not for ABS/EBS) Floor - Steel floor in the front area, followed by 70 mm softwood floor - In the wheel arch area: steel / chequer plate covering - Rear incline with 70 mm softwood floor - Low-bed platform including rear incline: 8,200 mm Access Ramps - Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable - Wooden overlay - Spring-lift assisted Operating Instructions - A special permit is required for 10,000 kg axle load. The permit must be applied for separately in each federal state; approval for 20-ton GVW is at the discretion of the authorities – customer’s responsibility. Country of Registration / License Plates - Registration country: Germany - With Dekra inspection and expert's report (according to §13 EC-FGV) - 24/7 service hotline - Prepared for two-line license plate holder - Reflective contour marking as per ECE R 048, white on the sides and red at the rear Paintwork - Frame: DB 7350 Novagrau - 10-year anti-perforation warranty - Drawbar: galvanized or painted black, depending on manufacturer's choice - Ramps: hot-dip galvanized Note: Archive images!

Durumu: yeni, makine/araç numarası: 56c59c8aba35227ffb44c9f75, boş ağırlık: 11.350 kg, azami yük ağırlığı: 26.650 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Jumbo Chassis Semi-Trailer Steel welded construction with closely spaced cross members, reinforced design, low-loader outer frame profile, suitable for transporting construction machinery up to 32,000 kg and a maximum external machine width of 2550 mm, fifth wheel plate with interchangeable 2'' kingpins. Rear slant approx. 1200 mm at 7°. Enclosed upper ramp shaft with steel/tread plate. In the low-bed section, omega rail laterally below the outer frame serves as a hanging strip for tarpaulins and distance holders for the lashing mushrooms, not in the wheel area. For the lift table: an additional fixed lightweight outer frame with omega profile allows for the lift table to be raised with closed tarpaulin! 24 t, 2-speed landing gear with single-side operation, half-round base and straight mounting plate, with thrust compensation. Free swing radius to rear: approx. 1950 mm. Rear support foldable 2 wheel chocks with holders Side underrun protection made of aluminium Quarter-shell mudguards at front and rear of each axle Anti-spray flaps behind each axle Rear underrun protection made of steel Full-width spray flap across the rear 4 stainless steel toolboxes, w=800/h=350/d=350 mm, with polished doors, lockable; 2 each on FR-left and FR-right in front of the 1st axle Lift table after gooseneck, approx. 3000 mm long, hydraulically liftable for driving over the gooseneck, with mechanical locking in raised position (cylinder angled for good ground clearance, Fliegl standard). Controls on FR-right + additional operation via wireless remote control (same as ramp operation). Lift table can be raised with tarpaulin closed! Tarpaulin hanging on lift table area on an additional lightweight fixed outer frame with omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms remain usable even when table is lowered! Lashing points Gooseneck: 4 pairs of 5 t lashing rings recessed into outer frame 2 pairs of lashing mushrooms, both above and on the sides, recessed into outer frame Low-bed: 8 pairs of lashing mushrooms, both top and side, recessed into outer frame, each 10 t 't 9 pairs of 5 t in outer frame Axles & Suspension SAF drum brake axles Last axle steered, with automatic reverse lock via reversing light, and additional lock feature on vehicle via hand button Air suspension with lift & lower valve + auto-reset function H & S function with quick venting 1st axle is an automatic lift axle, including forced lowering and starting aid, actuated by 3x braking (starting aid is functional up to 30% axle load exceedance and up to a max. speed of 25 km/h) Axle lift is below recommended driving height, therefore no guarantee for tire damage Wheels and Tyres 235 / 75 R 17.5 from leading manufacturers Steel twin wheels, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 tamper-proof coupling heads at front, no connecting line EBS, electronic braking system with EBS socket at front, no connecting cable Note: The trailer may only be towed by trucks that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck installation (no calibrated scale) Electrical System 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front, in LED Iiedpsi Riw Aefx Ag Nsa 2 white/red lane marker lights at the rear 1 rotating beacon with holder, switchable via parking light (removable beacon) 2 pairs of warning signs, double LED illuminated and e

Durumu: yeni, makine/araç numarası: ebf3f771e96394cd89e56bbb7, toplam ağırlık: 11.800 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further Information Chassis Central Axle Trailer Fine-grained steel welded construction 6 pairs of lashing eyes bolted to the exterior floor/frame, each rated at 5t 2 additional pairs of lashing eyes bolted to the floor in the corners, each rated at 5t Front support leg, gearbox type Foldable rear support 2 wheel chocks with holders Steel underrun protection Full-width rear mud flaps Quarter mudguards 1 plastic toolbox with shelf, dimensions b=620/h=360/d=440 mm, lockable with a padlock (padlock not included) Drawbar Central Axle Trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles & Suspension Drum brake axles as per manufacturer's specification Axle/chassis laser alignment for reduced tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation (balancing rocker) Wheels and Tyres 235 / 75 R 17.5 as per manufacturer's specification Factory silver steel rims Brake System 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at front with connecting lines to the tractor ABS and ALB, with ABS socket at the front and connecting cable Electrics 24 Volts, multi-chamber lights, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable sockets at the front, with connecting cable Floor Steel chequered plate floor for high point load capacity Note: Slight floor undulation due to welding distortion possible! Platform length approx. 5,200 mm Rear taper approx. 900 mm Front wall / corner posts 25 mm aluminium hollow profile, 400 mm high Side walls 25 mm aluminium hollow profile, 400 mm high, foldable and removable Rear wall / rear corner posts 1 pair steel posts fixed to the frame with holders to secure loading ramps, clear entry width approx. 2,430 mm Loading ramps 2 steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with hand grip on ramps Surfaced with 3 serrated steel tracks Gas strut support for single person operation Registration Country/ Plates Registration country: Germany 24/7 service hotline Prepared for single-line licence plate holder Contour marking with reflective tape as per ECE R 048, white at the sides and red at the rear Paintwork Frame hot-dip galvanised including passivation Iijdji Rixrjpfx Ag Nsa 15-year warranty against rust-through Front wall aluminium Side wall aluminium anodised Loading ramps hot-dip galvanised Note: These are archive images.

Durumu: yeni, makine/araç numarası: c3dd8c834afed73501f8074af, boş ağırlık: 3 kg, azami yük ağırlığı: 20 kg, toplam ağırlık: 24 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/55 r22,5, Further Information Chassis Swap Drawbar Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with robust supports on 20-foot base for swap bodies 7.15 and 7.45 m Turntable with heavy-duty ball bearing slewing ring 2 wheel chocks with holder Side underrun protection aluminium Rear underrun protection steel Half-shell mudguards front and rear 2 stainless steel toolboxes, b=600/h=400/t=500 mm, with polished door, lockable 1 pair of warning signs, double, LED illuminated, extendable to 3,000 mm at the rear, rear only 1 wiring provision for retrofitting customer-side warning signs at the front Drawbar equipment for turntable trailer Drawbar with certified 40 mm towing eye Drawbar mechanically adjustable in length by 6 x 100 mm increments and lockable (drawbar length approx. 1,900–2,500 mm) Drawbar height adjustment via spring Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axles/chassis laser measured – reduces tyre wear and fuel consumption Air suspension with lift & lower valve Wheels and Tyres 385/55 R22.5 Manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle EBS – electronic braking system with EBS connector at the front, with connecting cable Note: The trailer may only be towed by vehicles that ensure correct ABS operation! Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 front white position lights 2 rear white/red lane marker lights Removable rotating beacon 1 additional LED work light at rear, switched via reversing light 2 LED work lights on each side (1 left, 1 right), switched via reversing light 1 x 15-pin connector at the front, with connection cable Registration/Country Plates Country of registration: Germany With Dekra inspection and certificate (according to §13 EC – FGV) 24/7 service hotline Prepared for single-line number plate holder Iedoi Riylspfx Ag Njia Contour marking with reflective strips according to ECE R 048, white on sides and red at rear Paintwork Frame hot-dip galvanized including passivation – 15-year warranty against rust-through Drawbar KTL black

Durumu: yeni, makine/araç numarası: e763c8c2bb3370bd2342236a4, boş ağırlık: 3 kg, azami yük ağırlığı: 8 kg, toplam ağırlık: 11 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Central Axle Tipping Trailer Steel welded construction, continuous tipping shaft at the rear with 80 mm ball tip bearing Gearbox support leg at the front 2 wheel chocks with holders Steel underrun protection Lockable storage compartment for loading ramps underneath the platform Central axle trailer drawbar Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles + Suspension Euro-axles at our discretion, with tapered roller bearings and S-cam brakes Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalisation (rocker equaliser) Wheels and Tyres 235/75 R 17.5 manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Colour-coded line routing for easy servicing Hand spindle parking brake Integral air reservoir Without ABS, but with mechanical ALB. Maximum permissible speed: 60 km/h 2 unmistakable coupling heads at the front with connecting lines to the tractor unit Electrics 12 Volt, multi-chamber lights, no side yellow LED lighting, side reflectors 2 white position lights at the front 2 white/red marker lights at the rear 1 x 7-pin 12 Volt plug at the front, with connecting cable approx. 60 cm extended Hydraulics Three-way tipper, hydraulic multi-piston press with stroke limiter and safety cable Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK connector NW 10/3, incl. connection hose Operation hydraulically via PTO from the truck Tipper Body Robust tipper body with 4 mm steel sheet floor, steel drop side body, continuous side walls, fold-down and pivot-mounted with central locking at the bottom. Removable corner posts at the rear. Rear wall fold-down and pivot-mounted with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2,420 mm 5 pairs of lashing eyes in the floor, each 5 t Iijdpfoi Rizbex Ag Nsa Operating Instructions The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while complying with permissible axle, support, and kingpin loads. (Poor driving and trailing performance possible due to incorrect load distribution) Country of Registration / Licence Plates Country of registration: Germany with Dekra approval and certificate for max. 60 km/h registration, towing vehicle agricultural or forestry tractor (country of registration Switzerland max. 40 km/h possible) Prepared for single-line license plate holder Without contour marking / reflective stripes according to ECE R 048 Paintwork Frame hot-dip galvanised incl. passivation, 15-year warranty against rust-through Side walls/body RAL 3002 Carmine Red Note! If the body is galvanised, it will not be painted! Note! Body interior only primed! Wide tyres possible at extra cost. 355 / 60 R 18, then loading height approx. 980 mm Attention: Archive images!

Durumu: yeni, makine/araç numarası: 8fbda13da8c595f64678f0f82, boş ağırlık: 2.100 kg, azami yük ağırlığı: 11.300 kg, toplam ağırlık: 13.400 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 275/70 r 22,5, Further Information Chassis Central Axle Trailer Fine-grain steel welded construction Fifth wheel coupling, brand at our discretion, suitable for 2 king pins, with ball-bearing turntable, stop max. 20° Support at drawbar and at the front of the dolly Wheel chocks with holder Steel underrun protection Half-shell mudguards Central axle trailer coupling system CLG under-mount drawbar with approved 50 mm towing eyes for connection to dolly and truck, including drawbar lock on the truck! Axles + Suspension BPW disc brake axles Air suspension for Swap Train version, standard fifth wheel height lowered approx. 1100 mm, raised approx. 1280 mm, coupling height approx. 1140 mm, Braking System 2-line compressed air braking system, color-coded piping for easy service. Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to the truck 2 fail-safe coupling heads with spiral-flex connection lines to the trailer EBS, electronic braking system with EBS plug at the front, with connection cable, EBS spiral-flex connection lines to the trailer Iijdpfx Aoi Rizxeg Nsa Attention: The trailer must only be towed by vehicles that ensure the effectiveness of the ABS! with raising & lowering, ECAS, via truck controls, ECAS CAN 2 bus required in the truck. Without ECAS CAN 2 bus in the truck, additional control unit in the truck required (not included): Electrics with pre-wired cable and a distribution box. Operation via 15-pin socket pins 11 and 15 or for 2 x 7-pin sockets pins 7 and 5. Note! This version must still be technically approved in conjunction with the trailer. Dolly and trailer can presumably only be raised and lowered together; if this is not technically feasible, operation is via WABCO eTASC with hold function in the lowered position + auto-reset function (no power from the truck required). Additional operation on vehicle via WABCO eTASC + hold function in the lowered position + auto-reset function (no power from truck required) Vehicle - Driving Stability System ECAS only possible in conjunction with WABCO EBS. Axle load detection via EBS CAN bus signal for display in the driver’s cab (truck must be prepared accordingly, no truck installation/no calibrated scale) Brake release function from the truck (via switch) on pin 14 and additionally via switch on the vehicle next to raise & lower valve, for releasing the brake when coupled, EBS power supply must be ensured! With CAN router Wheels and Tires 275/70 R 22.5, brand at manufacturer’s discretion Steel rims, factory silver Electrics 24 volt, multi-chamber lights, side-mounted yellow LED lighting Side-mounted yellow LEDs linked to turn signals, flashing side markers 2 white LED position lights at the front 2 white/red lane-marking lights at the rear 2 x 7-pin fail-safe connectors at front, with connection cable, 2 x 7-pin fail-safe connectors with spiral-flex connection lines to the trailer Cable + plug/socket for reversing camera system, depending on vehicle type Operating Instructions Note! Observe the Long Truck Regulation! Please observe currently approved route network! Towing vehicle must be brought to Triptis factory for approx. 1 week for drawbar adaptation! Please observe CLG recommendations per attachment Mandatory before order acceptance: Submission of all relevant dimensions as per Fliegl CLG form (see attachment) The coupling height of the planned trailer must be known Fliegl Fahrzeugbau assumes no liability for defects in dimensional accuracy and drivability

Durumu: yeni, makine/araç numarası: 408ba9a39bbb8087056d6e563, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 aks, lastik boyutu: 235 / 75 r 17,5, Further information Chassis Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support Iedji Ri Daepfx Ag Neia 2 wheel chocks with holder Side underrun protection made of aluminium Full-width rear splash guard Semi-shell mudguards on 1st and 2nd axles with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess over the rear axles, running to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes rated 5 t each in the excavator arm recess at the longitudinal frame, approx. 300 mm from the front and approx. 200 mm before the rear incline 1 plastic toolbox, with insert shelf, w=620/h=360/d=440 mm, lockable with padlock (lock not included) 1 storage box recessed in the gooseneck in the floor with lid, W=720 mm/L=520 mm/D=170 mm Extendable width to 3,000 mm (not in the rear incline) (track width of machines or vehicles to be transported must not exceed outer frame width of 2,550 mm) Timber beams 70 mm for extension to 3,000 mm Storage compartment for timber beams under loading area Lashing rings lowbed (40 lashing points) 1 pair of lashing rings on gooseneck, each 5t 9 pairs of lashing studs, integrated in the top and side of outer frame, each 10t 2 x on gooseneck in front 7 x in the lowbed area 6 pairs of lashing holes in the outer frame of the lowbed area, 5 t each (for tie-down straps) 3 additional pairs of folding lashing rings, each 10 t 1 x inside next to main frame at start of lowbed 1 x on gooseneck (protrudes) 1 x recessed in the floor behind the last axle Trailer drawbar assembly Drawbar with tested 50 mm towing eye, towing eye inclined at 8°, D-value minimum 160 kN Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load compensation front and rear (rocker compensation) Wheels and Tires 235 / 75 R 17.5 as selected by manufacturer Steel twin wheels, factory silver Brake system 2-line air brake system Spring-loaded parking brake 2 anti-mismatch coupling heads at front, with connection lines to truck ABS and ALB, with ABS plug at front, with connection cable Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at front 2 white/red marker lights at rear 2 x 7-pin anti-mismatch plugs at front, with connection cable 1 LED rotating beacon with holder, controlled via parking light (beacon detachable) 2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm Floor Gooseneck at front with steel/aluminium chequer plate covering followed by 70 mm softwood floor, with steel/aluminium chequer plate over wheel wells Rear incline with 70 mm softwood floor Access ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable with timber surfacing Hydraulic, powered via tractor PTO with flow restrictor, controlled laterally front left Hydraulic connection with SVK plug NW 10/3, including connecting hose Approval country / Plates Approval country: Germany 24/7 service hotline Prepared for two-line number plate holder Contour marking with reflective tape as per ECE R 048, side white and rear red Warning sign according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation, 15 years corrosion perforation warranty Drawbar galvanized or black, as per manufacturer’s choice Access ramps hot-dip galvanized Note: Images are for illustrative purposes (archive images)!

Durumu: yeni, makine/araç numarası: 71cc13750cef13b72f7a55abe, boş ağırlık: 5.500 kg, azami yük ağırlığı: 29.500 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22,5², Further Information Chassis Semi-Tipper Fine-grain steel welded construction with lightweight design, fifth wheel plate with replaceable 2" kingpin Curved front wall, patented 24t two-speed landing gear, single-sided operation, with straight lower section, without push-rod compensation 2 wheel chocks with bracket Underride protection, foldable Half-shell mudguards Integrated mudguard holder with stone-repellent surface Anti-spray mud flaps on rearmost axle only 1 tarp pole with bracket 2 towing hooks at rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Axles in off-road version Air suspension 1st axle automatic lift axle, including forced lowering and start assist, operated by pressing brake three times (start assist functions up to 30% axle overload and up to max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against corrosion Brake System 2-line compressed air brake system, color-coded pipelines for easy service Spring-loaded parking brake 2 anti-mix coupling heads at front, without connection line EBS, Electronic Brake System with EBS socket at front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of ABS! With raise and lower valve Vehicle stability control system Wheels and Tyres 385/65 R22.5, make per manufacturer’s choice Steel rims, factory silver Electrics 24 Volt, multi-chamber lights, side yellow LED marker lights 2 white position lights at front 2 white/red contour marking lights at rear 2 x 7-pin anti-mix sockets at front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chromed, with HD coupling nut, fixed part, NW 48 mm (without hose connection) Operated hydraulically via vehicle PTO Body Aluminium box body made from high-quality, wear-resistant material; front wall 5 mm thick, external side walls from 30 mm hollow section profiles, expertly welded, with spill-repellent top rail profile. Internal ladder on front wall (not with Cramaro option). Shovel and broom holder outside on front wall. Greenline – conical and aerodynamic body shape Membrane – tailgate Iisdoi Ri Efjpfx Ag Nsa Tailgate pendulum-mounted with double hinge and split 1/2 to 1/2 with top swing arm, with one grain slide per door. Tailgate with rubber seal. Note: Heat-resistant up to max. 170°C! Floor throughout 6 mm thick Standing platform with access steps, connector plate for air/electrics and brake with ample space for ease of use Roll tarp to be stowed on right side (FR-right) with central locking on left side (FR-left) Operating Notes For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent material damage and corrosion. The stated gross weight is technically possible; depending on the load, the gross weight may not be achievable within the allowable axle/kingpin/load limits. (Poor driving and trailing behavior may result from incorrect load distribution) Country of Registration / Signs Germany Approval according to EC 2007/46 24/7 Service Hotline Prepared for single-line license plate holder Conspicuity markings with reflective tape according to ECE R 048, white side and red rear Paintwork Frame DB 7350 Novagr

Durumu: yeni, makine/araç numarası: 207ad28f83705ed0d38a4f174, boş ağırlık: 3 kg, azami yük ağırlığı: 11 kg, toplam ağırlık: 14 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235/75 r17,5, Further information Chassis Swap Central Axle Trailer Fine-grain steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with robust outriggers for 20-foot swap bodies, suitable for swap bodies 7.15 and 7.45 rear-flush (for 7.15 swap bodies, not rear-flush; forklift pockets/frame protrudes) Telescopic support leg at the front 1 pair of gearbox support feet at the front, with straight lower part and single-sided operation on the right (FR) Wheel chocks with holder Aluminium side underrun protection Steel rear underrun guard Half-shell mudguards Mounting for truck-mounted forklift at the rear, incl. 2 fork insertion pockets, 2 extendable support tubes, bracket for chain securing with locking pin. Rear underrun guard with light unit can be folded away. Includes 2 loose rubber pads to protect the rear panel; we recommend counterweight! Note: Partially low ground clearance with forklift, poor trailing behaviour possible, no guarantee! (Forklift self-weight up to max. 1,500 kg for trailers.) (With proximity switch for forklift control in conjunction with lift axle) The forklift mounting shifts the axles rearwards, pay attention to load distribution when driving without a forklift. Customer risk! (For swap body trailers, driving with forklift is only permitted in conjunction with a swap body.) Forklift mount adapted as per AU 203670 for 7.45m swap bodies Counterweight at the front between the frames, approx. 300 kg, if required, exact check still pending Drawbar equipment for central axle trailers Drawbar with approved 50 mm towing eye, forwarding edition (not suitable for trucks with tail lift, exact check still required when ordering) Undercoupler drawbar Drawbar without length adjustment Axles + Suspension SAF drum brake axles as per manufacturer's choice Axles/chassis laser-aligned to reduce tyre wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, colour-coded line routing for easier service Spring-loaded parking brake Duomatic connection at front, with connecting line to the tractor, on the left (FR) Duomatic connection at front, with connecting line to the tractor, connection on the right (FR) EBS, Electronic Braking System with EBS plug at the front, with connection cable, on the left (FR) Attention: The trailer may only be towed by towing vehicles that ensure the functionality of the ABS! Iiedpei Ri Iaofx Ag Nsa With lift & lower valve, holding function in each lift/lower position Vehicle - Drive stability system Wheels and Tyres 235/75 R17.5, brand as per manufacturer's choice Steel twin wheels, factory silver Electrics 24 Volt, 4 x 3-chamber tail lamps + 1 round reversing lamp + 1 round rear fog lamp, side yellow LED lighting, lights mounted protected! 2 white position lamps at the front 2 white/red lane marking lamps at the rear 1 x 15-pin connector at the front, with connecting cable, on the left (FR) 2 x 7-pin sockets at the rear left (FR) for truck-mounted forklift 1 x 15-pin socket at the rear left (FR) for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reverse light) Additional LED work light at rear, switched via reverse light Approval / Plates Germany With Dekra inspection and certificate (as per §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour markings with reflective tape as per ECE R 048, white on the sides and red at the rear Painting Frame DB

Durumu: yeni, makine/araç numarası: 06017a31026c05fc8f6ccf5ae, boş ağırlık: 3.055 kg, azami yük ağırlığı: 14.945 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, lastik boyutu: 235/75 r17,5, Further information Chassis: Swappable rotating dolly Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with robust outriggers on 20-ft base for swap bodies 7.15 and 7.45 Rotating dolly with heavy-duty ball bearing turntable 2 wheel chocks with holders Aluminium side underrun protection Steel rear underrun protection Quarter mudguards at the front and half-mudguards at the rear Drawbar device for dolly trailers Drawbar with certified 40 mm towing eye Axles & Suspension SAF drum brake axles Laser-measured axles/chassis for reduced tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system, color-coded line routing for easy servicing Spring-loaded parking brake 2 foolproof coupling heads at the front, with connecting lines to the motor vehicle EBS, Electronic Braking System with EBS plug in front with connecting cable Note: The trailer may only be towed by towing vehicles that can ensure effective ABS operation! With raise & lower valve, holding function in both lower and raised positions Wheels and tires 235/75 R17.5 tires, brand at manufacturer's discretion Iijdsi Ri Rcepfx Ag Noa Steel twin wheels, factory silver Electrics 24 volt, multi-chamber LED lights with resistor, yellow LED side marker lights, LED number plate light (Note: Certain towing vehicles may trigger false diagnostics despite proper functioning) 2 white front position lights in LED 2 white/red lane marker lights at rear in LED 1 x 15-pin plug at front with connecting cable Additional LED work light at the rear, switched via reverse light Approval / Plates Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame: DB 7350 Novagrau Note: Archive images!

Durumu: yeni, makine/araç numarası: c13a96854ea37997845c1bf36, boş ağırlık: 6.860 kg, azami yük ağırlığı: 28.140 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235/75 17,5,

Durumu: yeni, makine/araç numarası: d24246f092ae53c0e155d19dd, boş ağırlık: 2.400 kg, azami yük ağırlığı: 13.600 kg, toplam ağırlık: 16.000 kg, Further information Chassis tandem trailer Steel welded construction with approx. 152 mm high floor section; load-oriented and torsion-resistant steel frame structure. Longitudinal floor beams with a load-resistant outer frame and a guide tunnel every 600 mm, tunnel with positioning aids at the top and sides; tunnel height approx. 45 mm. 4 interchangeable container corner fittings on 20ft basis. 4 jack legs for jumbo parking height 970 mm, extendable and foldable sideways by 90°, with short safety strut and securing mechanism, pin lock on the frame, sturdy spring bolt as additional transport lock, symmetrical arrangement of legs Form A 2 for CWB C 745 / 782, suitable for parking height approx. 970 mm. Reinforcement between support legs. 7 pairs of lashing rings recessed in the outer frame, each rated at 2.5 t. Heavy-duty pallet stops on both sides, approx. 20–25 mm high, lashing option every 200 mm, loading height reduced by approx. 20–25 mm. Side-mounted door retainers. Rear underrun protection made of flat steel. Flooring Phenolic resin-coated plywood panels, approx. 27 or 30 mm thick (manufacturer's choice), designed for high point load capacity, suitable for forklift axle loads up to max. 4,400 kg. Front bulkhead/corner posts 2,800 mm high, remaining section covered with tarpaulin; volume-optimized steel corner posts; quick-release device for side curtain at front bulkhead. Central stanchions 1 pair of sliding stanchions, adjustable along the full length, with four pockets for insert slats and long lower pocket. Insert slats 3 rows of aluminum V-insert slats or wooden insert slats as per manufacturer, plus 1 additional row of aluminum V-insert slats. Rear wall/corner posts rear Rear steel corner posts up to underside of roof, curtain suspension with round tube and tensioning ratchet. Rear portal doors, double-wing, each with 2 internal locking rods. Curtain Tarpaulin with welded-in horizontal and vertical tension belts. Tension locks in stainless steel. Roof Sliding roof; rear Endlift, can be folded up high at the back, roof slides from rear to front; L-roof beam designed for the automotive industry; internal width between roof beams approx. 2,490 mm, curtain color: white. EcoLift – lifting roof, can be raised by approx. 380 mm, gas-strut assisted. Approval / Plates Country of registration: Germany. Manufacturer's certificate according to EN 12642 XL. Paintwork Chassis hot-dip galvanized. Front corner posts hot-dip galvanized. Ijdpfokt Ni Uox Ag Njia Front wall aluminum. Rear corner posts hot-dip galvanized. Rear wall white. Tarpaulin RAL 9005 jet black with advertising lettering. Attention! These are archive images.

Durumu: yeni, makine/araç numarası: 92df8e9d6c187f34b20298f39, boş ağırlık: 4.900 kg, toplam ağırlık: 35.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 385/65 r22,5², Further Information Chassis Semi-Trailer Tipper Iodpsi Riz Rjfx Ag Njia Fine-grained steel welded construction, lightweight design, saddle plate with replaceable 2" kingpin Patented curved front end Central telescopic support leg, uncoupling with load not possible; when uncoupled, vehicle must be positioned inclined towards the rear. 2 wheel chocks with holders Foldable underrun protection Half-shell mudguards Integrated mudguard mount, stone-repellent surface With anti-spray splash guards on the last axle only 1 tarpaulin bar with holder 2 towing hooks at the rear Axles & Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser alignment to reduce tire wear and fuel consumption Axles in off-road specification Air suspension 1st axle with automatic lift axle, including forced lowering and traction aid, actuated by braking three times (traction aid functional up to 30% axle load exceedance and up to max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded piping for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS electronic braking system, with EBS socket at the front, no connecting cable Note: The trailer must only be towed by tractors that ensure the effectiveness of ABS! With raise & lower valve Vehicle stability control system Wheels and Tires 385/65 R22.5 – manufacturer at the manufacturer's choice Steel rims, factory silver Electrical System 24 volt, multi-chamber lights, yellow LED side marker lights 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin non-interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Actuation hydraulically via truck PTO Bodies Aluminum box body made of high-quality, abrasion-resistant material: front wall 5 mm thick, outer rear walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent upper frame profile. Interior has a step-up at the front wall (not in combination with Cramaro). Shovel and broom holders outside on the front wall. Greenline – conical and aerodynamic body shape Membrane rear wall Rear wall as pendulum tailgate with double-joint hinge, external mounting with double hook locking. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor seamlessly 6 mm thick Standing platform with step-up, connection plate for air/electrical and brake lines with generous clearance for optimal operability. Roll tarpaulin stows to FR-right, with central locking at FR-left Operating Information For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to prevent material degradation and rust. The stated total weight is technically possible. Depending on the cargo, the total weight may not be achievable while complying with permissible axle, support, and kingpin loads. (Poor driving or tracking behavior due to incorrect load distribution possible.) Registration Country / Plates Germany Approval according to EC 2007/46 24/7 Service Hotline Prepared for single-line license plate holder Contour markings with reflective tape according to ECE R 048, white on the side and red at the rear Paintwork Frame DB 7350 Nova Grey 10 years