Kullanılmış Diğer Çalışma Platformu satın al (66)

Durumu: yeni, azami yük ağırlığı: 31.630 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring system with indication option in the truck via EBS signal – no truck-side installation required * Warning sign package at front and rear * Reflective contour marking strips on the sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED rotating beacon Dodsrczm Dspfx Ag Tjkg * 24 V 15-pin power cable and additional 12 V 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm draw eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in basket design, right side * Front enclosed single plastic mudguards * Rear straight steel mud flaps, each with spray suppression (anti-spray design) * Side underrun protection * Extended offset neck, 500 mm forward * Turntable platform extended by 520 mm at the front with 45° corners, 3 integrated lockable storage compartments with covers * Chassis made from high-strength fine grain steel * Floor over turntable platform made of 50 mm softwood, lowbed platform made of 60 mm softwood * Outer planks of the loading ramps made from 50 mm bamboo wood * Four stake pockets each side (stakes not included), each with 2 t lashing possibility * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the turntable platform, one pair 13.4 t lashing rings each front and rear side on the outer frame, four pairs each side of 10 t swiveling and lowerable lashing rings, loadable in all directions and recessed in the outer frame, two pairs 6.4 t lashing rings on the excavator arm recess, 8 pairs of galvanized folding outriggers for 3 m total width (not at the rear end slope) * Extension planks stored in a side compartment on the left * Excavator arm recess over rear axle to end of ramp slope approx. 2,300 x 740 x 190 mm * Mechanical fall supports at the rear * Hydraulically galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic side ramp shift on sliding pipe from ramp shaft * Loading area over turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Laden loading height approx. 860 mm (including 860 mm ramp slope) * Chassis, turntable, loading ramps, mechanical rear folding supports hot-dip galvanized * Axles, springs, air tanks, and turntable painted in black tone * New vehicle with manufacturer's warranty * Subject to prior sale and errors * Available from calendar week 46 / 2025

Durumu: yeni, azami yük ağırlığı: 14.000 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 11.000 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 2.340 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 3.500 mm, Üretim yılı: 2025, Donanım: hidrolik arka platform, * Metal-Fach T019/1 * Bale Trailer * New vehicle * New model * Year of manufacture: 2025 * Gross weight: 18,000 kg * Payload: 14,000 kg * Unladen weight: 4,000 kg * Overall dimensions: 13,627 mm x 2,550 mm x 3,500 mm * Loading platform dimensions: 11,000 mm x 2,550 mm x 2,347 mm * Loading height: 1,153 mm * Front and rear loading racks * Tires: 445/45 R19.5 * Chassis made of high-grade steel * Floor made of checker plate * ADR axles * Side underrun protection * Tension chains for front and rear loading racks * Side access ladder * Lashing eyes for tie-down straps every 50 cm * Large storage box * LED lighting * Air brake system * Mudguards on all wheels * Certified for 40 km/h ATTENTION !!!! PLEASE READ CAREFULLY !!!!! Dkjdpfx Aephk Theg Tsg We expressly reserve the right to prior sale, as this item is also offered on other platforms. We highly recommend inspection and verification to avoid any misconceptions regarding the condition and suitability of the vehicle. Viewings and inspections are possible at any time by appointment and are expressly encouraged!!! Images may be similar and may show optional, extra-cost equipment. Stated internal dimensions are approximate. The seller is not liable for any errors, input mistakes, or data transmission issues. Changes and prior sale reserved! Inspection & test drives are only possible by telephone appointment. Information provided online is non-binding and does not constitute guaranteed features. This advertisement serves solely as a preview of our vehicle and is not a part of any sales contract! TRADE-INS POSSIBLE FOR ALMOST EVERYTHING!!! TRADE DEALS AND ADDITIONAL PAYMENTS POSSIBLE!!! Exhibition site: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday – Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Over 500 new and used trailers always in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Durumu: kullanılmış, azami yük ağırlığı: 14.170 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 02/2006, yükleme alanı uzunluğu: 6.530 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.000 mm, toplam genişlik: 2.550 mm, Toplam ağırlık: 18.000 kg Boş ağırlık: 3.830 kg Yük kapasitesi: 14.170 kg Toplam uzunluk: 8.550 mm Yükleme uzunluğu: 6.530 mm Genişlik: toplam genişlik 2.550 mm / yükleme genişliği 2.540 mm Yükseklik (yerden yükleme yüksekliği): yaklaşık 1.000 mm Diğer bilgiler Dkedpjw N A Eyjfx Ag Tjg - Omega profilli sert ağaç taban - Yan paneller mevcut - Çift tekerlekli - BPW akslar - Yük sabitleme halkaları - LED geri vites lambası

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2024, * PT 30 Profile: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lifting and lowering feature as well as RtR valve * Smart-Board installed as infotool on the trailer (for axle load display—front and rear separated) * Tire pressure monitoring with display option in the truck via EBS signal, without installation on truck side * Side underrun protection * Swivel support legs at the rear chassis frame * Mechanically adjustable warning board packages front and rear * Front axle plastic quarter mudguards with splash protection * Rear axle straight galvanized steel skirts with splash protection Dksdpfxjtplwie Ag Tsg * Reflective contour tape on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Toolbox, galvanized sheet steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted on right side * Compartment in the bogie for accessories with folding lid, 2 container locks permanently installed (directly behind bogie platform) * ROBOT-welded anti-slip coating on the steel surface of the bogie platform (protruding weld beads) * Load securing package consisting of: 2 lashing rings (13.4 t) front left & right on the front wall carrier; front & rear, 1 pair each of UVV lashing rings (13.4 t); and 3 pairs per side of UVV lashing rings (10 t) – pivotable and lowerable, loadable in all directions and integrated in side frame; 3 each side stanchion pockets with simultaneous 2 t lashing capability * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear slope) * Widening planks stowed in the center of the loading platform * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically adjustable side-to-side * 4-way control block for retrofitting hydraulic ramp displacement * Chassis, bogie, folding outriggers, drop legs and loading ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in a black shade * Loaded loading height approx. 910 mm +/- 20 mm with air suspension * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 11.400 kg, toplam ağırlık: 15.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 12.000 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 850 mm, toplam genişlik: 2.550 mm, Üretim yılı: 2025, Metal-Fach T009 Bale Trailer 3-Axle Platform Trailer Flatbed Trailer New vehicle Year of manufacture: 2025 Overall dimensions: 11990 mm + 800 mm x 2480 mm x 2900 mm Internal dimensions: 9300 mm + 800 mm x 2380 mm x 1875 mm Gross weight: 15,000 kg Unladen weight: 3,560 kg Payload: 11,440 kg Loading height: 1,160 mm Tyres: 500/50-17 Extendable loading platform Wide tyres Air brake system ALB regulator Djdstw N D Sjpfx Ag Tskg Side underrun protection Side lighting Parabolic suspension Parking brake Adjustable front and rear loading racks Y-drawbar Road registration possible for 40 km/h Mudguards Custom paint option available !!! IMPORTANT - PLEASE READ CAREFULLY !!! We expressly reserve the right to prior sale, as this item is also offered on other platforms. We strongly recommend inspection and testing to avoid any misunderstanding regarding condition and suitability. Inspections and tests are possible at any time by appointment and are expressly encouraged!!! Images may show optional, surchargeable accessories. The given internal dimensions are approximate values. TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! PART EXCHANGE AND ADDITIONAL PAYMENT POSSIBLE!!! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday – Friday 8:30 a.m. to 5:00 p.m., Saturday 8:30 a.m. to 2:00 p.m. Over 500 new and used trailers in stock at all times!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Durumu: yeni, azami yük ağırlığı: 31.000 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.290 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 950 mm, * PT 40.0 Profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift and lower system and RtR valve * Pressure gauge scale for load weight determination (axles separated into 2 air suspension circuits) * Side underrun protection * Swing-out supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front and rear * Front axle: plastic quarter mudguards with splash protection * Rear axle: straight, galvanized steel sheet skirts with splash protection * Reflective contour tape on the sides and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power connector * LED lighting system 12/24 V * Removable LED rotating beacon at the rear Dsdpfx Ajl Tlhreg Tokg * 2 LED reversing lights (activated by reverse gear) * Drawbar with 50 mm towing eye and height adjustment * Tool box made of galvanized, black powder-coated steel sheet, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOT-welded anti-slip covering on the steel plate of the turntable platform * Load securing package consisting of: 1 x 13.4 t UVV lashing eye on left and right in front of the front wall support, 4 holes on each side of the turntable platform with 2 t lashing capacity each, 1 pair of lashing eyes (13.4 t) hanging at the rear left & right in front of the rear support, 4 pairs of UVV lashing rings (10 t) per side, pivoting and lowerable, loadable in all directions and integrated into the outer frame, 3 stake pockets per side with simultaneous 2 t lashing option * Hot-dip galvanized mechanical folding outriggers for 3 m total width (not at the rear bevel) * Beam holder for extensions under the chassis on the left, longitudinally * Excavator arm holder above the rear axle up to the end beam, approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 t lashing eyes per side in the excavator arm holder * Hardwood floor on the running surfaces of the low-loader platform * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) mechanically adjustable laterally * Outer beams of the loading ramps made of hardwood * Steel construction prepared for 6-control valve block * Loading edge unloaded approx. 950 mm +/- 20 mm chassis * Turntable, folding outriggers, mechanical drop supports, loading ramps hot-dip galvanized * --Axles, air tank, drawbar painted in a black tone-- * Tyres 235/75 R 17.5 * Vehicle has a one-day registration in 07/2024 due to missing tire pressure monitoring system and was never loaded/used * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 9.000 kg, toplam ağırlık: 11.600 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 9.080 mm, yükleme alanı genişliği: 2.520 mm, yükleme alanı yüksekliği: 850 mm, toplam genişlik: 2.550 mm, Üretim yılı: 2025, Metal-Fach T014/2 Bale Trailer 2-Axle Platform Trailer Flatbed Trailer New Vehicle Year of Manufacture: 2025 Overall Dimensions: 9089mm + 800mm x 2520mm x 2880mm Internal Dimensions: 6409mm + 800mm x 2380mm Loading Height: 1150mm Gross Weight: 11,600kg Unladen Weight: 2,600kg Payload: 9,000kg Tyres: 400/60-15.5 Extendable Loading Platform Wide Tyres Air Brake System ALB Regulator Side Underrun Protection Side Lighting Parabolic Suspension Parking Brake Adjustable Front and Rear Load Racks Y-Drawbar Road Approval up to 40km/h Possible Mudguards Custom Paintwork Available Dedpfx Agshlr Rds Tekg PLEASE NOTE! IMPORTANT INFORMATION—PLEASE READ! We expressly reserve the right to prior sale as this item is also listed on other platforms. We highly recommend viewing and inspection to avoid any misconceptions regarding condition and suitability. Viewings and inspections are possible at any time by prior arrangement and are expressly encouraged! Photos may include optional, extra-cost accessories. All internal measurements are approximate values. TRADE-INS ACCEPTED FOR ALMOST ANYTHING! TRADE AND PART-EXCHANGE POSSIBLE! Showroom: 58285 Gevelsberg, Am Sinnerhoop 17 Opening Hours: Monday – Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Constantly over 500 new and used trailers in stock! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Durumu: yeni, azami yük ağırlığı: 16.400 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as an information tool on the trailer, with pressure sensors for axle group load indication * Side underrun protection * Mechanically adjustable warning sign boards at the front and rear * Front axle: closed plastic mudguards; rear axle: straight galvanized steel skirts, both with splash protection * Foldable (hot-dip galvanized) cover for the toolbox in the turntable platform * Toolbox made from galvanized sheet steel, approx. 650 x 300 x 600 mm (black powder-coated), mounted on right side * 15-pin electrical connector * LED lighting, 12 / 24 V * Removable LED beacon at rear * Side marker lights with indicator control * Towing bar with 40 mm towing eye, height adjustable via tension spring and turnbuckle Dkedpfx Aeq Dyvceg Tjg * Tire pressure monitoring system with in-cab display via EBS signal (no installation required on the truck) * Rubber lining on the folding ramps and on the left and right drive-up slope (approx. 860 mm long) * Rubber lining on longitudinal members from bulkhead to end crossmember * Hardwood flooring on the running surfaces of the low-bed platform * 4 stake pockets per side, each with 2 t lashing capacity * Load securing package consisting of: 5 pairs of UVV load rings, swiveling and retractable, loadable in all directions and recessed into the outer frame - corners rated to 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the sloped rear section) * Timber support holders under loading platform in longitudinal direction * Raised roller stop in front of the bulkhead, with 1 x 6.4 t lashing ring on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically deployable ramp tip and load-holding valves * Hydraulic lateral ramp adjustment * Rear hydraulic support (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck from over 40 l to max. 140 l / min) * Hydraulic control block, splashwater protected * Dual-line hydraulic system * Platform above turntable: approx. 1,960 x 2,520 mm * Rear loading platform: approx. 6,500 x 2,520 mm (including 860 mm approach ramp) * Loaded platform height: approx. 890 mm +/- 20 mm (air suspension adjustment) * Chassis, turntable, roller stop, folding extensions, and access ramps hot-dip galvanized * Axles, turntable, drawbar, air tanks, etc. painted black * Loaded platform height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 14.550 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension, drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * External folding support legs at the rear * Toolbox made of galvanized sheet steel, approx. 650 x 350 x 320 mm, mounted laterally on the right (powder-coated in black) * Side underrun protection Dedpfxjpk D D Hj Ag Tjkg * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * Reinforcement package for drill rig transport on chassis – loading height + 20 mm * 50 mm softwood floor, clamped design * Provisions in front of the bulkhead for subsequent installation of container locks * Bolted smooth sheet steel front wall * Drop-down side walls of trapezoidal profiled steel with tailgate spring assist * Steel rear panel, retractable between ramps – bracket inside ahead of front wall for storage when not in use * Bolted rear stanchions * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * In each front and rear corner: one 10 t lashing point; various holes for 1.2 t lashing options in the front and rear cross members * One-piece mechanical grating ramps with spring assist for single-person operation, approx. 2,750 x 620 mm (can be compacted to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, front wall, tailgate, rear folding supports, and access ramps hot-dip galvanized * Axles, springs, air tanks, and landing gear painted in black * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Side board coating in RAL 9010 pure white * Painting of the side walls in a RAL color of your choice available at extra charge * New vehicle with manufacturer's warranty * Subject to changes and prior sale * Immediately available from Egestorf

Durumu: yeni, azami yük ağırlığı: 10.750 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: * RDÜ Tire Pressure Monitoring System * EBS Braking System * Emergency Release Device for Spring-Loaded Brake Cylinders * Drum Brakes * 2 x 7 t Gigant Axles * Parabolic Springs with Compensating Unit * Drawbar height-adjustable by approx. 300 mm – drawbar extension by 250 mm to a total of 2,250 mm * 15-pin electrical connector * LED lighting Dkodpfx Aov Eq Evjg Tog * Front support winch * Fold-out rear support legs * Plastic toolbox approx. 858 x 500 x 500 mm mounted at the front right on the outside of the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood flooring * Mounting provision at the front wall and rear slope for retrofitting container locks for transporting 20" containers * Bolted front wall made of smooth sheet metal * Side walls made of trapezoidal-profiled steel sheet, foldable, split once in the middle * Steel rear wall insertable between the ramp brackets, stored inside in front of the front wall when not in use * Bolted rear stakes * Exterior frame with perforations, approx. 45° angled, with 2 t lashing capacity every 480 mm, installation option for 3 t drop-forged lashing rings every 600 mm, in the front and rear corners each 1 x 6.3 t lashing ring, various holes in the front and rear crossmembers for 1.2 t lashing options * One-piece mechanical grid ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be telescoped down to 20 mm) * Rear driving ramp, approx. 860 mm chassis height * Drawbar, front wall, tailgate, folding supports, and ramps hot-dip galvanized * ---Axes, springs, air tanks, flange towing eye as well as support winch painted in a black tone--- * Reinforced and certified structure according to EN 12642 XL, incl. load securing certificate-- * Wheelbase 1,140 * Painted drop sides in RAL 9010 pure white * Painting of side walls in any RAL color available at an extra charge * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 23.700 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with manual lowering at rear * Pressure gauge for axle load determination (separate display for both air suspension circuits) Djdpjl Tpwyofx Ag Tekg * Side underrun protection * Rear swing-out supports on chassis frame * Mechanically adjustable warning sign packages, front and rear * Front axle: closed plastic mudguards; rear axle: straight galvanized steel skirts, both with spray protection * Reflective contour marking tape on sides and rear * Hinged (hot-dip galvanized) lid for toolbox on the turntable platform * LED tail lights * Removable warning beacon at the rear * Drawbar with 40 mm draw eye and adjustable height via tension spring & turnbuckle * 2 x 7-pin electrical connectors * Four stake pockets on each side, each with 2 t lashing point * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on main frame of the turntable platform, 5 pairs of UVV (Accident Prevention Regulation) lashing rings, tiltable and lowerable, loadable in all directions and recessed into the outer frame - 13.4 t in corner positions, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not present on rear beveled section) * Widening boards stored in the center of the loading area * Hydraulic one-piece ramps (approx. 3,000 x 720 mm), adjustable in width * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm approach ramp) * Chassis, turntable, drawbar, folding extensions & ramps hot-dip galvanized * Axles, turntable, air tanks etc. painted in black * Tyres: 235/75 R 17.5 * Payload approx. 24,000 kg at 30,000 kg gross vehicle weight * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 14.660 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs, 110 mm wide, with tandem equalizing unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing legs at the front * External folding supports at the rear * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of bulkhead for retrofit installation of container locks * Bolted bulkhead made of smooth sheet metal * Side walls made of trapezoidal-profile steel sheet, foldable, with drop-side shock absorbers Dedsl Th Hwopfx Ag Tskg * Steel tailgate, insertable between the ramps – storage bracket provided inside at bulkhead when not in use * Rear stanchions bolted * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Possible installation of 3 t drop lashing rings every 600 mm * In each corner front and rear 1 x 10 t lashing ring; various holes in front and rear crossbeam for 1.2 t lashing points * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, ramps and folding supports hot-dip galvanized * Side board painting in RAL 9010 pure white * Painting of side walls in an RAL color at extra cost possible * Axles, springs, air tanks, flange towing eye, and landing legs painted black * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 10.360 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 14.4: * TPMS (Tyre Pressure Monitoring System with in-cab display via EBS signal, installation on the truck side not required) * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 5.5 t Gigant axles * Air suspension with lifting and lowering functionality * Drawbar height adjustable by 300 mm * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox in front right, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards * LED lighting system * 15-pin power connector * Hot-dip galvanized chassis, drawbar, front, and rear walls * 50 mm softwood floor * Prepared for subsequent installation of 20" container locks at the front and rear * Bolted bulkhead made of smooth sheet metal * Side walls made of trapezoidal steel sheet, folding, with drop-side spring assist * Bolted, hot-dip galvanized rear stanchions * Perforated outer frame angled at approx. 45°, with 2 t lashing capacity every 480 mm, can be equipped with 3 t folding lashing rings every 600 mm, 1 x 6.3 t lashing ring in each front and rear corner; multiple holes in bulkhead and endmember for 1.2 t lashing possibilities * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles, stowed at the rear below the platform in a compartment integrated in the chassis * Vehicle fully hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale Dodpfopk D Dqsx Ag Tokg * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 14.200 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2023, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension * Drawbar with 50 mm flange eye and height adjustment of 110 mm via offset plate * Jost landing leg at front * External folding support legs at rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted on right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED lights * Reinforcement package for drilling equipment transport on the chassis * 50 mm softwood flooring, clamped design * Pre-fitted assembly rail in front of headboard for retrofitting container locks * Bolt-on headboard made of smooth sheet metal * Split steel sheet (trapezoidal profile) side walls, foldable with central folding stanchion * Steel tailboard, retractable between ramps, with internal storage mount in front of headboard when not in use * Rear stanchions bolted * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option for installing 3 t drop lashing rings every 600 mm * Load securing package: in each front/rear corner 1 x 10 t UVV lashing point, 2 x 8 t UVV retractable lashing rings per side in outer frame, various 1.2 t lashing options via holes in front/rear crossmember * One-piece mechanical grating loading ramps with spring mechanism for one-man operation, approx. 3,000 x 620 mm (contract to 20 mm) Dkodpfsl Tp Azjx Ag Tog * Rear approach angle approx. 860 mm * Chassis, drawbar, headboard, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, air reservoirs, flange eye, and landing leg painted in black * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls can be painted in a RAL color of your choice at extra cost * Vehicle has a day registration (unused) * Errors and prior sale excepted * Immediately available from Egestorf, near the A7

Durumu: yeni, azami yük ağırlığı: 10.900 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring System) * EBS electronic braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension * Height-adjustable tow bar by approx. 300 mm; tow bar extension by 250 mm to 2,250 mm * Jost landing gear at the front * LED tail lights * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox, front right side, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis as well as tow bar, bulkhead, rear wall, tailgate, and loading ramps * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted smooth sheet metal bulkhead * Drop side walls made from trapezoidal-profiled steel sheet, foldable with drop side spring assist * Steel rear wall, can be stored between ramps; holder for unused rear wall inside at the bulkhead * Bolted rear stanchions * Perforated outer frame, approx. 45-degree bent, with 2 t lashing capacity every 480 mm; optional installation of 3 t recessed lashing rings every 600 mm; each corner at front and rear with one 6.3 t lashing ring; various holes for 1.2 t lashing points in bulkhead and rear crossmember * Single-piece mechanical grating ramps with spring system for one-man operation, approx. 2,750 x 600 mm (retractable to 20 mm) * Rear approach angle approx. 860 mm * -- Reinforced and certified body to EN 12642 XL, including load-securing certificate -- Dkedpfxoq Dyvyo Ag Tsg * Drop side color in RAL 9010 pure white * Painting of side walls in RAL color of your choice available at extra cost * New vehicle with manufacturer’s warranty * Errors and interim sale excepted * Available immediately from Egestorf

Durumu: iyi (kullanılmış), Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: YGCD160XTF0017195, azami yük ağırlığı: 215 kg, ilk tescil: 07/2015, bir sonraki muayene (TÜV): 11/2027, toplam uzunluk: 6.155 mm, toplam genişlik: 1.800 mm, toplam yükseklik: 2.300 mm, lastik boyutu: 195R14C 106N, renk: kırmızı, Üretim yılı: 2015, çalışma saatleri: 2.588 h, Detaylı bir teklif veya bir inceleme randevusu için bizimle iletişime geçmekten çekinmeyin! Djdsxu D Rajpfx Ag Tjkg HEMATEC Arbeitsbühnen GmbH // KLUBB, ISOLI ve DINO çalışma platformu üreticilerinin Almanya temsilciliği, Dresden, Vehlefanz (Berlin yakınlarında), Göttingen ve Lauchheim şubeleriyle hizmetinizdedir. Çalışma platformlarıyla ilgileniyorsanız, bizimle iletişime geçebilirsiniz.