Alçak şasi dorse

Wiese SA 36 CS-S Tieflader-Auflieger Plane,Rampe

Durumu: yeni, makine/araç numarası: 56c59c8aba35227ffb44c9f75, boş ağırlık: 11.350 kg, azami yük ağırlığı: 26.650 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 3 dingil, lastik boyutu: 235 / 75 r 17,5, Further information Jumbo Chassis Semi-Trailer Steel welded construction with closely spaced cross members, reinforced design, low-loader outer frame profile, suitable for transporting construction machinery up to 32,000 kg and a maximum external machine width of 2550 mm, fifth wheel plate with interchangeable 2'' kingpins. Rear slant approx. 1200 mm at 7°. Enclosed upper ramp shaft with steel/tread plate. In the low-bed section, omega rail laterally below the outer frame serves as a hanging strip for tarpaulins and distance holders for the lashing mushrooms, not in the wheel area. For the lift table: an additional fixed lightweight outer frame with omega profile allows for the lift table to be raised with closed tarpaulin! 24 t, 2-speed landing gear with single-side operation, half-round base and straight mounting plate, with thrust compensation. Free swing radius to rear: approx. 1950 mm. Rear support foldable 2 wheel chocks with holders Side underrun protection made of aluminium Quarter-shell mudguards at front and rear of each axle Anti-spray flaps behind each axle Rear underrun protection made of steel Full-width spray flap across the rear 4 stainless steel toolboxes, w=800/h=350/d=350 mm, with polished doors, lockable; 2 each on FR-left and FR-right in front of the 1st axle Lift table after gooseneck, approx. 3000 mm long, hydraulically liftable for driving over the gooseneck, with mechanical locking in raised position (cylinder angled for good ground clearance, Fliegl standard). Controls on FR-right + additional operation via wireless remote control (same as ramp operation). Lift table can be raised with tarpaulin closed! Tarpaulin hanging on lift table area on an additional lightweight fixed outer frame with omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms remain usable even when table is lowered! Lashing points Gooseneck: 4 pairs of 5 t lashing rings recessed into outer frame 2 pairs of lashing mushrooms, both above and on the sides, recessed into outer frame Low-bed: 8 pairs of lashing mushrooms, both top and side, recessed into outer frame, each 10 t 't 9 pairs of 5 t in outer frame Axles & Suspension SAF drum brake axles Last axle steered, with automatic reverse lock via reversing light, and additional lock feature on vehicle via hand button Air suspension with lift & lower valve + auto-reset function H & S function with quick venting 1st axle is an automatic lift axle, including forced lowering and starting aid, actuated by 3x braking (starting aid is functional up to 30% axle load exceedance and up to a max. speed of 25 km/h) Axle lift is below recommended driving height, therefore no guarantee for tire damage Nedpfxsi Riw Aj Afgswc Wheels and Tyres 235 / 75 R 17.5 from leading manufacturers Steel twin wheels, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 tamper-proof coupling heads at front, no connecting line EBS, electronic braking system with EBS socket at front, no connecting cable Note: The trailer may only be towed by trucks that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck installation (no calibrated scale) Electrical System 24 volt, multi-chamber lights, side yellow LED lighting 2 white position lights at the front, in LED 2 white/red lane marker lights at the rear 1 rotating beacon with holder, switchable via parking light (removable beacon) 2 pairs of warning signs, double LED illuminated and e

Durumu: kullanılmış, azami yük ağırlığı: 36.216 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.100 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Üretim yılı: 2024, Donanım: ABS, FAYMONVILLE MAX100 3-axle SANH semi low-loader forklift transport trailer First registration: 10/2024 Unladen weight approx. 13,200 kg Fifth wheel height: 1,150 mm Low-bed length: 9,300 mm Gooseneck length: 3,800 mm Internal width: 2,480 mm Load height in the low-bed: 860 mm Height-adjustable tarpaulin superstructure, adjustable by approx. 400 mm Nwedpfxjx Nlhrs Afgjc EDSCHA sliding roof, movable forward The structure can be hydraulically widened at the rear portal by approx. 750 mm Loading area behind the gooseneck hydraulically raisable and lowerable, length approx. 2,800 mm; gooseneck and low-bed with grating flooring, over the axles: checker plate flooring with integrated sand coating Two-part steel ramps, approx. 3,185 + 1,420 mm, width 1,250 mm each, also with grating surface, max. load capacity 30,000 kg Tyres: 13 x 235/75 R 17.5 BPW axles with drum brakes 1st axle: LIFT AXLE 3rd axle: STEERABLE TRAILING AXLE Air suspension with raising/lowering function WABCO trailer EBS 24-volt E-hydraulics RENTING is the new BUYING – immediately available from us with full-service rental as well.

Durumu: yeni, azami yük ağırlığı: 36.461 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.480 mm, toplam yükseklik: 860 mm, Üretim yılı: 2026, Technical Description Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Area: Hydraulically liftable and lowerable platform after the gooseneck, approx. 2,800 mm in length, with rear taper approx. 1,000 mm x 8°. 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN). 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN). 1 pair of foldable lashing rings to the inside on the front central beam (LC 10,000 daN). Grating floor covering C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles tread plate covering. Two-Piece Steel Ramps: One pair of galvanized two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating covering C40/5 (point load 8 t on an area of 20 x 20 cm). Ramps with hydraulically folding ramp sections and hydraulic lifting mechanism. Njdpfsw Dl Hwex Afgewc Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not included in the overall vehicle length of 16,500 mm. Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R17.5 3PMSF tyres at the manufacturer’s discretion. TPMS: TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface according to ISO 11992. For proper display, the towing vehicle must be capable of transmitting and displaying this data. Axles: BPW axles and suspension, 2 rigid axles, 1 trailing steering axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated by reverse gear and manually. Air suspension with lift and lower valve. Axle tools. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit. Electrical System: Electrical system complying with EU regulations, 24-volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicators. ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Manufactured from high-strength fine-grained steels. Steel grades: – S355J2+N / S355MC (yield strength 355 MPa) – S690QL / S700MC (yield strength 690 MPa) Curtain Body: Curtain body ??? 3,960 mm ??? – Galvanized front wall with tensioning system for sliding curtains. – "EDSCHA" brand roof, forward-sliding on ALU roof bow profiles (bolted to front and rear wall). – 3 pairs of sliding stakes in the loading area. – Rear of the body hydraulically extendable to left and right by approx. 750 mm. – Sliding roof with upwards foldable portal beam. – Sliding curtain with 700 mm length reserve, lashing straps approx. every 600 mm. – Height to upper edge of body approx. 3,960 mm (loaded). – Driving with open sliding roof is prohibited and will damage the curtain. Paintwork: Entire steel structure is automatically blast-cleaned with a wheel blasting machine after welding. Second blast treatment with corundum for optimal coating adhesion. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection. Final painting with 2 coats of 2K topcoat, single colour, shade of choice according to RAL system 841GL. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint.

Durumu: yeni, boş ağırlık: 12.300 kg, azami yük ağırlığı: 37.200 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 30 mm thick hardwood flooring - 3 pairs of lashing rings Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Loading platform: - Loading platform with rear chamfer approx. 1,000 mm x 8° - Approx. 48 mm hardwood flooring, over the axles with checker plate surface Njdpfetvfkfsx Afgowc Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering axle - Air suspension with lift and lower valve - Self-steering axle with electro-magnetic reverse lockout, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" king pin - One galvanized steel headboard - Yellow-red air couplings on the galvanized connection rail at the front - 4 chocks with holders on the headboard - Mounting at the rear of the gooseneck for ALU drive-on ramps - 3 height levels of aluminum planks - Galvanized folding supports under the chamfer of the loading platform - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized headboard with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - Roof brand "EDSCHA" sliding forward on ALU roof rail profiles, bolted to front and rear wall - 3 pairs of sliding stakes in the loading platform - Body rear left and right hydraulically extendable by approx. 750 mm - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm reserve length, with tension belts at spacing approx. 600 mm - Upper edge of structure approx. 3,960 mm high - Driving with open sliding roof is not permitted and will cause damage to the curtain - Cover plates for bridging the gap between ramps and loading platform - Electro-hydraulic unit at the rear, beneath the loading platform - At the gooseneck and at the ramps left and right each a bracket for warning panels incl. socket - Control valves for the ramps positioned on the right trailer side - 6 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform - Lift axle at the front axle - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm on the right in driving direction between the axles - On the checker plate on the gooseneck and loading platform, a painted sand layer for slip resistance - Central lubrication system BEKAMAX (Pico) with standard lubricant NLGI-2 and removable guard around the pump - Four warning panels extendable by approx. 400 mm, each approx. 423 x 423 mm, with position light - Load pressure gauge for determining axle loads including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then visible defined surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Durumu: kullanılmış, azami yük ağırlığı: 31.300 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2019, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.050 mm, toplam genişlik: 2.550 mm, Donanım: ABS, Meusburger MPG-3 Alçak Tır Perdeli, Yönlendirilebilir/Kaldırılabilir Dingil Donanım: Havalı süspansiyon * Dingil kantarı * 1. dingil kaldırılabilir * 3. dingil yönlendirilebilir * Ek destekli ve uzaktan kumandalı hidrolik rampa * Geçişli rampa * Uzaktan kumandalı elektrikli vinç * Edscha tavan * Her iki tarafta depolama kutuları * Yedek lastik (yolda kullanım için) * Ekstra farlar * Çıkarılabilir genişlik levhaları Güvenlik: ABS * EBS * Disk fren Nwedpfx Aewfwd Djfgjc Hatalar ve ön satış hakkı saklıdır. Dahili araç numarası: 8303

Durumu: kullanılmış, azami yük ağırlığı: 44.980 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 09/2024, bir sonraki muayene (TÜV): 09/2025, toplam genişlik: 2.550 mm, Donanım: ABS, Our entire fleet of vehicles, including immediately and soon available models, can be found on our website. Selection of features. Complete specifications available on request. Chassis, stepped frame: * Special steel frame made from high-strength fine-grained steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle layout. Wheel covers above the axles with spray-suppression Nsdolthguepfx Afgewc * All steel parts sandblasted * Side underrun protection made of anodised aluminum fitted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area to enable the greatest possible low-bed length in combination with AluLeg support legs instead of telescopic landing gears, max. rear swing clearance of the tractor unit approx. 2,100 mm Special superstructure with extendable rear stanchions * Self-supporting aluminum roof bow/profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear stanchions extendable to approx. 4,200 mm * Three sliding stanchions per side with rubber spring relief * Additional middle stanchion lockings in the roof bow and stowage position, actuated by pull cable and spring latch * Mechanically adjustable lifting roof, lift height approx. 400 mm, operable from both sides or one-sided without opening the opposite side or doors * Additional height adjustment approx. 480 mm in approx. 40 mm increments via stanchion adjustment * Front overlap at the bulkhead for driving under tarpaulin up to overall height approx. 4,400 mm * Four rows of approx. 150 mm stackable aluminum slats per side, 450 mm pockets at the bottom, four rows of single pockets above * Only three rows of plug-in slats in the upper deck. Spacings evenly distributed Floor * Approx. 27 mm special water-resistant bonded beech multiplex panels, rough surface * Steel sheeting in the wheel arch area * Suitable for forklift traffic according to DIN ? standard * Outer frame flush finish Brakes * WABCO air brake system with EBS according to EC Directive 71/320 EEC including PREV (Park Release Safety Valve) * Spring-type parking brake cylinders * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer axles with drum brakes, low-loader version * Air suspension with lifting and lowering function, total travel approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical locking Twin tires * 235/75 R 17.5, -16-fold, incl. spare wheel holder, without spare wheel Paintwork * Chassis RAL 3002 red, single color * Middle stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork in single-tone RAL color Special equipment included * ECAS air suspension, operation on the trailer * Oversize signage front and rear, galvanized, stepless telescoping with marker lights incl. bases for revolving beacons (small plates) * Additional external unlocking for sliding tarpaulin frame * 4 stanchion adapters for special outer frame profile, for locking the middle stanchions arbitrarily * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, extra-wide and extra-high version, flat hooks, tarpaulin folds, closures with ratchet/OCS * Rear left telescoping base for revolving beacon incl. light * Outer frame for machinery transport with approx. 64 lashing points in 2,000 kg, 3,000 kg, and 10,000 kg versions, according to construc

Durumu: kullanılmış, azami yük ağırlığı: 26.100 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2013, bir sonraki muayene (TÜV): 02/2025, yükleme alanı uzunluğu: 13.650 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 3.000 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Donanım: ABS, Krebs Mega Sliding Curtain Semi-Trailer with Dhollandia Tail Lift, 9-ton Capacity with Ramp Function * Recently fitted with new tarpaulins, rear and front portals newly painted * SAF axles * 1st axle liftable * 3rd axle is a trailing steering axle * Dhollandia tail lift type DHLSU.90, lifting capacity 9,000 kg, ramp function * Remote control * 3 large storage boxes * Work lights * Ice-Protect Nedpfx Afou Em Nnogjwc For further information, please do not hesitate to contact us.

Durumu: yeni, azami yük ağırlığı: 37.500 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Complete specification available upon request. Chassis, cranked: * Special steel frame made from high-tensile fine-grain steels, electrically welded at the joints * Well-dimensioned outer frame * 3-axle configuration * Wheel covers above the axles with spray suppression * All steel parts sandblasted * Lateral underrun protection made from anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 5,000 mm * Special design in the cranked area – for maximum low-bed length in combination with AluLeg landing legs * Drop-leg supports instead of telescopic support winches, maximum rear swing radius for the tractor unit 2,100 mm Special body with rear stake widening: * DINKEL – Special body construction * Self-supporting aluminium roof rail / profile approx. 100 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable to approx. 4,200 mm (for loading and unloading only) * Three sliding stakes per side with rubber tension relief * Additional intermediate stake locks in the roof rail and parked position, via rope and spring latch * DINKEL – mechanical lift roof height adjustable * Lift roof height approx. 400 mm, operable from either side without opening the opposing side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments, height adjustment in stakes * Front overlap at bulkhead for on-road operation under tarpaulin up to total height 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats at each side, lower portion has 450 mm pockets, above are four rows of single pockets * In the high-bed, only three rows of insert slats, gaps evenly distributed Floor: * Approx. 27 mm thick special water-resistant bonded beech plywood, textured surface * In the wheel arch area: steel sheet. Forklift rated to DIN standard * Outer frame flush with the surface Brakes: * WABCO compressed air braking system with EBS according to EC directive 71/320 EEC incl. PREV (park-release safety valve). Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and aggregate load indicator * Including WABCO tyre pressure monitoring Axles: * 3 x 10,000 kg SAF axles with drum brakes in low-loader specification Njdpfx Aswx Dcmefgowc * Air suspension with raise and lower function, total stroke approx. 230 mm * Third axle as friction-steered trailing axle with electric and mechanical lock Twin tyres: * 235/75 R 17.5, 12-ply. Premium brand of our choice, including spare wheel mount Lighting: * In compliance with EC standards, side markers in LED version * Position lamps in LED version * 2 additional reversing lights * 2 work lights on inner front wall, top section Paintwork: * Chassis and superstructure in RAL colour (RAL 3002) * Intermediate stakes and axles KTL coated black * Corner stakes hot-dip galvanised * Plastic parts in black * Galvanised parts unpainted * Rims in factory silver * Bodywork in RAL colour, monochrome Included special equipment: * Air suspension in ECAS version, operated on the trailer * Intermediate stakes with additional roof rail lock, operated via pull-rope from below * Additional sliding-roof frame unlocking from outside * 4 stake adapters for special outer frame profile, for variable locking of intermediate stakes * PVC sliding tarpaulins, colour SILVER similar to RAL 9006, in oversized width and height, flat hooks, curtain folds, cl

Durumu: iyi (kullanılmış), çalışma saatleri: 4.299 h, kaldırma yüksekliği: 3.000 mm, Üretici: KALMAR Model: DCE100-6 Yıl: 2010 Kapasite: 12 ton Nwjdpfx Afjv D Ixdegsc Boş Ağırlık: 16 ton Kaldırma Yüksekliği: 3 m Çalışma Saati: 4.299 saat Donanım: Isıtıcılı tam kabin, 2 m çatal uzatması