Alçak şasi dorse

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader

Durumu: kullanılmış, azami yük ağırlığı: 37.950 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2024, bir sonraki muayene (TÜV): 02/2026, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment list available on request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading area: * Telescopic loading area with rear slope approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and widening in the lower section * Between 1st and 2nd axle a pair of fixed wheel recesses with covers, approx. 1,610 x 700 x 400 mm (L x W x D) * Recess in the sloped area and extending into the loading area for excavator arm reception, approx. 2,900 x 750 x 210/290 mm (L x W x H) * 1 pair of flat-mounted lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) * Incl. 3-piece removable galvanized covers over the wheel recess - max. point load approx. 3.5 t / each Axles: * BPW axles and suspension, 2 rigid axles, 3rd axle self-steering * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually Ijdjyc Axyopfx Acyehw * Air suspension with lift and lower valve * Axle tool kit Tyres: * 235/75 R 17.5 3PMSF tyres Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel construction: * High-strength fine-grained steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * First-class and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc-rich primer * High-quality single-tone 2-component (2K) finishing coat in RAL 3002 carmine red * Rear section metalized and painted in RAL 9010 pure white Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * Spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection rail at the front * 4 wheel chocks with holders on the front wall * Mounting at the rear of the gooseneck for aluminium loading ramps * Galvanized foldable supports under the rear slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Yellow reflector tape according to EU regulations on the sides, extension and rear of the trailer * Bracket on the gooseneck and rear plate, left and right, for warning signs incl. socket * One mud flap at the rear of the trailer * Manual and documentation on USB stick * On the warning signs, a bracket for rotating beacon * European reflector plates (red-yellow) at the rear of the trailer * 80 km/h speed decals on the rear and both sides * Load manometer for axle load determination including load diagram * On the gooseneck, plug-in aluminium side panels and rear wall, approx. 2,440 x 400 mm (L x H) * Rear galvanized drop-in stakes are removable (superstructure length approx. 2,560 mm) * A tool ...

Durumu: yeni, azami yük ağırlığı: 39.670 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Summary of equipment. Full equipment details available upon request. Gooseneck: * Gooseneck with approx. 30 mm thick hardwood flooring * Gooseneck at the rear, straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading Area: * Extendable loading area * 5 pairs of fold-out lashing rings on the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings on the outside (LC 10,000 daN) * 1 pair of lying lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, diamond plate over the axles Landing Legs: JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, two fixed and two self-steering axles * Air suspension with lifting/lowering function * Self-steering axles with electromagnetic reversing lock, can be activated via reverse gear or manually * Drum brakes * Axle tools Tyres: * 205/65 R 17.5 * Brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141 * Data transmission to the tractor via standardised EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to transmit and display this data Brake System: * Brake system in compliance with EU regulations with EBS-E (4S3M), without connector lines to the tractor unit Steel Construction: * Steel structure made from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: * Entire steel structure automatically shot-blasted after welding Iedpfx Asxarlvocyohw * Secondary blast treatment with corundum for optimal coating adhesion * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection * Final paint finish with 2 coats of 2K topcoat, single colour in RAL 3002 carmine red, according to RAL 841GL * Rims in silver * Rear section metallised and painted in RAL 9010 (pure white) * Metallic paints not possible * Paint system tested in salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Electrical System: * Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights flash with the indicators * ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets; connections according to ISO (24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098) Accessories included: * 2-inch king pin * One spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanised front connection rail * Galvanised drop supports under the ramped section of the loading area * One galvanised steel bulkhead (EN12642-XL), approx. 1,600 mm high * Removable ALU side boards and rear gate approx. 2,440 x 400 mm (L x H) on the gooseneck * Rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) * Support block with 1 pair of WADER container pockets; fifth wheel load approx. 20,000 kg * 7 pairs of WADER container pockets for 1x 20' container in the loading area * 1x 40' container in the loading area, 1x 40' container above the gooseneck, 2x 20' container * 7 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading area * One galvanised crosswise holder under...

Durumu: yeni, azami yük ağırlığı: 36.360 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete stock of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with front chamfered corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Telescopic loading platform with rear chamfer approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm as well as lower area widenings * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (width approx. 670 mm) – max. point load 5 t each * Recess in the chamfer and protruding into the loading platform to accommodate an excavator bucket handle (approx. 2,900 x 750 x 210/290 mm – L x W x H) * 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 2 pairs of lashing rings in the excavator bucket recess (LC 5,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Two-part steel ramps: * One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulically foldable ramp sections and hydraulic lifting gear, hydraulically adjustable * Maximum load per pair: 40,000 kg Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lockout via reverse gear and manual activation * Air suspension with lift and lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – make at our discretion Ihjdpfxjyhkq Uj Acyew TPMS: * TPMS Tyre Pressure Monitoring System according to ECE R 141 Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure optimal corrosion protection * Final coating with two layers of 2K topcoat, single-color in RAL 3002 Carmine Red, according to RAL System 841GL * Rims in silver-grey Incl. the following additional features: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Electro-hydraulic unit at the rear, under the loading platform * On the gooseneck, plug-in aluminum side and rear panels, approx. 2,440 x 400 mm (L x H). The rear galvanized stanchions are removable. (Body length approx. 2,560 mm) * One galvanized toolbox, integrated into the chamfered gooseneck * 2 pairs of WADER container pockets in the loading platform for a 20' or 30' container * 3 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the loading platform * 3 pairs of additional removable, galvanized covers over the wheel recesses – max. point load 3.5 t each * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional hook-on intermediate table, ap

Durumu: yeni, azami yük ağırlığı: 37.075 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment details. Complete specification available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45°, with rear bevel approx. 750 mm x 10° * 3 pairs lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading platform: * Loading area aft of the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs outward-folding lashing rings (LC 5,000 daN) * 2 pairs outward-folding lashing rings (LC 10,000 daN) * 1 pair inward-folding lashing rings at the central beam front (LC 10,000 daN) * Cutouts in the external frame of the loading area for securing strap hooks (LC 2,000 daN) * Grating floor covering C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), checker plate floor covering above the axles Two-piece steel ramps: * One pair galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections * Hydraulic lifting unit, hydraulically adjustable * Maximum load capacity per pair: approx. 40,000 kg Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steered axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting and lowering valve Brake system: Isdpfoyhkrrox Acyshw * WABCO brake system according to EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * Tire Pressure Monitoring System (TPMS) according to ECE R 141 Paintwork: * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with two layers of 2K top coat, single color in RAL 3002 Carmine Red in accordance with RAL System 841GL * Wheels in silver grey Accessories included: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * Grating floor covering in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating floor covering in the loading platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electro-hydraulic unit at the rear beneath the loading area * On the gooseneck – plug-in aluminum side and rear walls, approx. 2,440 x 400 mm (L x H). The rear galvanized stake pockets are removable (body length approx. 2,560 mm) * One electric cable winch with remote control, approx. 5,400 kg pulling force, incl. wire rope approx. 9.5 mm thick, approx. 24 m long, with guide roller * Bolted approx. 5t ring for winch cable insertion on the gooseneck without deflection roller * One galvanized toolbox, integrated in the gooseneck bevel with an opening for a winch * Grating floor covering on the gooseneck C30/3 (point load approx. 2t over an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stanchions approx. 100 x 50 mm in the external frame of the loading area * Lift axle on the front axle, controlled via TEBS E in accordance with current axle load and loading condition * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs at the r

Durumu: yeni, azami yük ağırlığı: 37.075 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick Loading Platform: * Platform behind the gooseneck hydraulically liftable and lowerable, approx. 2,800 mm long, with rear chamfer approx. 1,000 mm x 8° * 6 pairs of fold-out lashing rings (LC 5,000 daN) Isdoyhkqzopfx Acyjhw * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of fold-in lashing rings on the central beam at the front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over axles with checker plate Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding and unfolding ramp sections. Hydraulic lifting, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Gear: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lift and lower valve Brake System: * WABCO braking system in accordance with EU regulations, with EBS-E (2S2M) Tires: * Tires 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tire pressure monitoring system in accordance with ECE R 141 Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) ensuring optimal corrosion protection * Final paint with 2 layers of 2K top coat, single color in RAL 3002 carmine red, in accordance with RAL System 841GL * Wheels in silver-gray Accessories included: * 2-inch kingpin * Galvanized steel front wall approx. 400 mm high * Grating surface in the gooseneck chamfer C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating surface in the loading platform chamfer C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Painted sand layer as anti-slip on the checker plates above the kingpin and platform * Electro-hydraulic unit at rear beneath the loading platform * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H). The rear galvanized stakes are removable. (Body length approx. 2,560 mm) * Electric cable winch with radio remote control, lifting force approx. 5,400 kg, incl. approx. 9.5 mm thick wire cable, approx. 24 m long, with cable guiding roller * Bolted approx. 5 t ring for redirecting the winch cable on the gooseneck without guide pulley * One galvanized toolbox integrated in the chamfered gooseneck with an opening for a cable winch * Grating surface on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes, approx. 100 x 50 mm, in the outer frame of the loading platform * Lift axle on the front axle, controlled via TEBS E based on current axle load and loading status * 7 pairs inst...

Durumu: kullanılmış, azami yük ağırlığı: 38.440 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 08/2023, bir sonraki muayene (TÜV): 08/2026, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Complete equipment list available on request. - Load area with rear bevel, approx. 1,000 mm x 8° - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm - JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) - BPW axles and suspension, 1 axle with self-steering function - Technical axle load: 12,000 kg each - Air suspension with lifting and lowering valve - One-color topcoat in RAL 3002 carmine red - 2-inch kingpin - Galvanized front wall made of steel, approx. 400 mm high - Electro-hydraulic unit at the rear under the load area - Load gauge for determining axle loads, including load diagram - On the gooseneck: plug-in aluminum drop sides and rear panel, approx. 2,440 x 400 mm (L x H) - One galvanized toolbox integrated into the beveled gooseneck - 6 pairs of stanchion pockets for approx. 100 x 50 mm plug-in stanchions in the outer frame of the load area - Extensible galvanized side extensions, approx. 230 mm per side - Lift axle on the first axle - 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear - 2 LED reversing lights mounted on the rear panel - HRM metallization (High Resistance Metallisation) Ihodpfx Acsxthz Tsysw

Durumu: kullanılmış, azami yük ağırlığı: 39.780 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 01/2023, bir sonraki muayene (TÜV): 01/2027, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our entire stock of vehicles, including those available for immediate or short-term delivery, on our website. Extract from the equipment list. Complete specification upon request. Gooseneck: * Gooseneck with approx. 45° chamfered front corners and a rear chamfer of approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading bed * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of flat lashing rings at the front of the loading bed (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: * Tyre size 205/65 R 17.5, twin-mounted Axles: Ihedpex Uvlrofx Acysw * BPW axles, two fixed axles, two air-suspended self-steering axles, with drum brakes and lift/lower function * The self-steering axles have an electromagnetically controlled reverse lock, operable via reverse gear or manually Brake system: * Brake system compliant with EU regulations with EBS-E (4S3M), without connection lines to the tractor unit Steel structure: * High-strength fine-grained steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer * High-quality single-colour 2-component (2K) top coat in RAL 3002 Carmine Red * Rear section metallised and painted in RAL 9010 Pure White * Rims in silver Electrical system: * Electrical system according to EU regulations Lighting: * 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin connection per ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included accessories: * 2-inch kingpin * Galvanised steel front wall approx. 400 mm high * Spare wheel carrier in front of the front wall * Yellow-red air couplings mounted on the galvanised connection rail at the front * 4 wheel chocks with holders on the front wall * Mountings at the rear of the gooseneck for aluminium loading ramps * Galvanised folding supports under the rear slope of the loading area * Bracket for a beacon at the rear of the trailer * Yellow reflective tape as per EU regulations at sides, extension, and rear * Mounts for warning plates, left and right on the gooseneck and rear panel, including socket * Mudflap at the rear of the trailer * Manual and documentation on USB stick * European reflective plates (Red-Yellow) at the rear * 80 km/h speed stickers at the rear and both sides * Audible reverse warning signal * Load pressure gauge for axle load determination, including load chart

Durumu: yeni, azami yük ağırlığı: 37.150 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of vehicles, including immediately and short-term available units, on our website. Sample features – full specification available on request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Iodex H Hi Eopfx Acyjhw Extendable loading area: * Extendable loading area with rear chamfer approx. 1,000 mm x 8° * 6 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cut-outs in the outer frame of the loading area for attaching tie-down straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate over the axles Landing legs: * JOST landing legs (manual) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * 235/75 R 17.5 tyres, 3PMSF TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 * Data transfer to the tractor unit via standardized EBS interface according to ISO 11992. For correct display, the tractor must be able to transmit and display this data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting/tipping valve * Axle tool kit Brake system: * Brake system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel structure: * Steel structure made of high-tensile fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Complete steel structure is automatically shot-blasted after welding using a blast wheel system * Second blasting with corundum for optimal adhesion of the coating system * Top coat with 2 layers of 2K finish paint, single colour RAL 3002 Carmine Red, according to RAL System 841GL * Rims in silver grey * Rear section metallized and painted in RAL 9010 (pure white) * Coating build-up tested in salt spray test according to ISO 9227-NSS * Sealant applied to cavities with special wax Electrical System: * Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin connections according to ISO. 24N ISO-1185, 24S ISO-3731 * 15-pin ISO-12098 Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * Spare wheel carrier in front of the front wall * At the galvanized front connection rail, yellow-red air couplings * Mount at the rear of the gooseneck for ALU loading ramps * Galvanized folding supports under the loading area chamfer * Mounts for warning signs including socket on both the gooseneck and rear section, left and right * Load gauge for axle load determination including load chart * On the gooseneck, plug-in aluminium side and tail boards, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated into the chamfered gooseneck * 3 pairs of WADER container locks in the loading area for one 20' (30') or one 40' container * 6 pairs of pockets for plug-in stanchions, approx. 100 x 50 mm, in the outer

Durumu: yeni, azami yük ağırlığı: 37.820 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory with immediately or short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: Gooseneck with front corners beveled at approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load platform: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and widenings at the lower section * Between the 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (width approx. 670 mm) - max. point load approx. 5 t/each * Recess in the beveled area and extending into the load platform for accommodating the excavator dipper stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of horizontally mounted lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of outward foldable lashing rings (LC 5,000 daN) * 3 pairs of outward foldable lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the load platform for attaching tensioning straps (LC 2,000 daN) One-piece steel ramps: * 1 pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramp with hydraulic lifting system, hydraulically adjustable * Maximum load per pair: 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not have to be included in the vehicle length when in driving position Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 axles rigid, 1 axle self-steering * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, can be engaged via reverse gear and manually * Air suspension with lift and lower valve * Axle tools Tyres: * Tyres 235/75 R 17.5 3PMSF – Brand of our choice * TPMS tyre pressure monitoring system as per ECE R 141. Data transfer to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be capable of both receiving and displaying this data Brake system: * WABCO brake system in compliance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Steel construction: Ihedpfx Acsw Tpqwoyjw * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system as per EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S, and 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Coating: * Complete steel structure automatically shot-blasted with turbine system after welding * Second sandblasting with corundum for optimum adhesion of the coating system * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection * Final coating with two layers of 2K topcoat, plain color RAL 3002 Carmine Red in accordance with RAL system 841GL * Rims in silver * Rear section metalliz

Durumu: yeni, azami yük ağırlığı: 37.635 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with hardwood covering approx. 48 mm thick * Ramp with hydraulic lift, hydraulically adjustable * Maximum load per pair: 40,000 kg According to Regulation 1230/2012/EU, ramps with a length of less than 300 mm in transport position do not have to be included in the vehicle length Loading platform: * 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with checker plate strips approx. 15 x 15 mm and extensions in the lower section * Between the 1st and 2nd axle, one pair of permanently installed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) - max. point load 5 t each * Recess in the chamfer as well as into the loading platform for excavator stick positioning (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of flat lashing rings at the front of the loading platform (LC 10,000 daN) * 5 pairs of folding external lashing rings (LC 5,000 daN) * 3 pairs of folding external lashing rings (LC 10,000 daN), 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cut-outs in the outer frame of the loading platform for fixing lashing straps (LC 2,000 daN) Landing gear: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lift/lowering valve * Axle tool Tyres: * Tyres 235/75 R 17.5 3PMSF — make at our discretion * TPMS: Tyre pressure monitoring system according to ECE R 141. Data transmission to the truck unit takes place via the standardized EBS interface in accordance with ISO 11992. For correct display, the truck unit must be able to transmit and display this data Braking system: * WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical equipment: * Electrical system in accordance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted with centrifugal wheel machine after welding * Second blasting with corundum for optimal adhesion of the coating system Ihedpfx Acextc Ubeyow * Final paintwork in two coats of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL system 841GL * Rims silver * Rear section metallized and painted in RAL 9010 (Pure White) * Paint finish tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including the following additional features: *