Kullanılmış Müller-Mitteltal Beton Karıştırıcı satın al (260)

Durumu: yeni, azami yük ağırlığı: 10.800 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with equalizing unit * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm up to 2,250 mm * Tyre pressure monitoring with display option in the truck via EBS signal — no truck-side installation required Dsdpfsrwc R Asx Ag Tokg * Landing gear at the front * External folding supports at the rear * 15-pin electrical connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics * Plastic toolbox approx. 858 x 500 x 500 mm at the front right outside on the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provision in front of front wall for retrofitting container locks * Bolt-on 400 mm smooth-sheet steel front wall * Bolt-on rear stanchions * Drop sides with spring assistance * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm; possible installation of 3 t folding lashing rings every 600 mm; in the corners front and rear, 1 x 6.3 t lashing ring each; front and rear cross beams with various holes for 1.2 t lashing options * One-piece hydraulic grid ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm gap) * Hydraulic flow divider in trailer (with hydraulic pump output in truck over 40 l/min up to max. 140 l/min) * Chassis, drawbar, front wall, mechanical support legs, and ramps hot-dip galvanized * Axles, springs, air tanks, front landing gear, and drawbar eye painted in black * Sideboards painted in RAL 9010 pure white * Painting of side panels in an RAL colour of your choice available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: kullanılmış, dingil konfigürasyonu: 3 aks, ilk tescil: 04/2000, yükleme alanı uzunluğu: 10.790 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 950 mm, toplam uzunluk: 14.790 mm, toplam genişlik: 2.500 mm, süspansiyon: çelik, Üretim yılı: 2000, Ek bilgi: Marka: MÜLLER MITTELTAL Model: TS4 Yapı: Alçak şasi (platform U=10.790 mm / G=2.500 mm / Y=950 mm) Yıl: 2000 Süspansiyon: çelik Frenler: kampana Dkodpfx Agouwu Ezj Tjg Boyutlar: U/G: 14.790 mm / 2.500 mm Kütleler: dolu/boş: 57.000 kg / 11.800 kg HİDROLİK RAMPALAR / ÇELİK SÜSPANSİYON / KAMPANA FREN = Daha fazla bilgi = Süspansiyon: yaprak süspansiyon Boş ağırlık: 11.800 kg Taşıma kapasitesi: 45.200 kg Azami yüklü ağırlık (GVW): 57.000 kg Daha fazla bilgi için lütfen Andrei Somov, Mark Ševtšenko veya Deniss Urmaker ile iletişime geçiniz.

Durumu: kullanılmış, azami yük ağırlığı: 4.500 kg, toplam ağırlık: 6.500 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/1979, bir sonraki muayene (TÜV): 04/2026, yükleme alanı uzunluğu: 4.000 mm, yükleme alanı genişliği: 1.900 mm, yükleme alanı yüksekliği: 380 mm, toplam genişlik: 2.500 mm, toplam yükseklik: 3.000 mm, Üretim yılı: 1979,

Durumu: kullanılmış, boş ağırlık: 2.380 kg, azami yük ağırlığı: 8.320 kg, toplam ağırlık: 10.700 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 04/2016, bir sonraki muayene (TÜV): 06/2026, yükleme alanı uzunluğu: 5.030 mm, yükleme alanı genişliği: 2.010 mm, yükleme alanı yüksekliği: 325 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: gümüş, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Araç konumu: Bovenden, 2 aks, BPW aksları, tandem, yaprak yay süspansiyonu, ABS (antiblokaj sistemi), sabitleme halkaları, mekanik rampalar, ön destek, arka destek, yan alüminyum sürüş koruması, alet kutusu, yükseklik ayarlı çekme kolu Gövde: Mekanik rampa ve tandem alçak yükleme römorku. Rampalar galvanizli, 2x BPW aks, kampana frenler! Dkodpfjxqhltex Ag Teg Yükleme yüksekliği yaklaşık 700 mm! Rampa uzunluğu yaklaşık 2200 mm! AKSESUAR BİLGİLERİ GARANTİSİZ, değişiklik, ara satış ve hatalar saklıdır!

Durumu: kullanılmış, azami yük ağırlığı: 34.400 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 04/2009, bir sonraki muayene (TÜV): 07/2024, Donanım: ABS, Further questions are welcome via WhatsApp. Dkjdst E Eunopfx Ag Tog

Durumu: kullanılmış, azami yük ağırlığı: 8.100 kg, toplam ağırlık: 11.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 10/2008, yükleme alanı uzunluğu: 6.000 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, Toplam ağırlık: 11.000 kg Boş ağırlık: 2.900 kg Djdextfkfspfx Ag Tjkg Yük kapasitesi: 8.100 kg Toplam uzunluk: 8.100 mm Yükleme uzunluğu: 6.000 mm Genişlik: toplam genişlik 2.550 mm / kasa genişliği 2.480 mm Yükleme yüksekliği: yaklaşık 900 mm Diğer bilgiler - Yan duvar yüksekliği: 400 mm - Ahşap zemin - Yaylı yükleme rampaları U: 2.700 mm G: 600 mm - Yüksekliği ayarlanabilir çeki kolu - Lastik ebadı 235/75 R17,5

Durumu: yeni, azami yük ağırlığı: 10.900 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * Wabco EBS (Electronic Braking System) * RDÜ Tire Pressure Monitoring System * Emergency Release Device for Spring Brake Cylinders * Drum Brakes * 2 x 7 t Gigant Axles * Parabolic Springs with Tandem Equalizer Unit * Height-adjustable (approx. 300 mm) hot-dip galvanized drawbar with 40 mm flange towing eye * Jost mechanical landing leg at the front * Two rear mechanical hot-dip galvanized folding supports * 15-pin power connector * LED tail lights * Hot-dip galvanized bolted underrun protection * Right-side galvanized steel toolbox * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel pallet 3-way tipper body * Continuous upper side walls with internal tube reinforcement – foldable without center stanchions, with sideboard spring assist * Rear tailgate foldable and swinging, with manual central locking * Hot-dip galvanized bolted rear stanchions * Lashing rings: 1 x 5 t in each corner, and 4 x 3 t each side recessed in the outer frame * 4 mm fine-grained steel floor plate * Net hooks, rear track for ramp storage * Prepared for retrofitting of additional side wall extensions * Body reinforced with load securing certificate according to EN 12642 XL * Two-stage step on the left side for easier access * 1 pair of aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles Dkedpfxol Th A Eo Ag Tjg * Lockable storage compartment at the rear, mounted under the loading floor in the chassis * Axles, springs, air tanks, and landing leg painted in black * Chassis, drawbar, floor, front wall, folding supports hot-dip galvanized * New vehicle, unregistered, with manufacturer warranty * Tires: 385/55 R 22.5 * Side board paint finish in RAL 9010 pure white * Side wall paint finish in a different RAL color available at extra cost * Errors and prior sale reserved * Available from CW [calendar week]

Durumu: kullanılmış, azami yük ağırlığı: 13.860 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2022, yükleme alanı uzunluğu: 6.770 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 600 mm, yükleme alanı hacmi: 10 m³, Donanım: ABS, ? galvanizli şasi ? alçaktan bağlı ? 50 mm çekme halkası ? konteyner kilidi ? her iki tarafta 12 bağlama halkası Dksdpfx Ajxb Ig Ssg Tsg ? geri görüş kamerası ? kampana fren ? duomatic bağlantı ? ABS ? havalı süspansiyon ? alet kutusu ? EBS ? destek ayakları ? ikiz lastik ? BPW akslar Tüm bilgiler taahhütsüzdür / ara satış hakkı saklıdır.

Durumu: kullanılmış, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 11/2004, bir sonraki muayene (TÜV): 08/2026, * Müller Mitteltal TS3 alçak şasi treyler (dorseli) * İlk tescil: 11/2004 * 3 aks * Havali süspansiyon * Gigant akslar * Hidrolik uzun rampalar, kaydırılabilir ve katlanabilir * Yatak genişliği 2,50 m'den 3,0 m'ye kadar artırılabilir * Yükleme uzunluğu: 8,50 m, yükseklik: 0,85 m Dodpew Tgkbofx Ag Tjkg * Boyun kısmında yükleme uzunluğu: 3,40 m, yükseklik: 1,50 m * Destek ayakları * Boş ağırlık: 10.260 kg * Teknik toplam ağırlık: 47.000 kg * Muayene geçerlilik: 08/2026'ya kadar * Genel muayene: 02/2026'ya kadar geçerli

Durumu: yeni, azami yük ağırlığı: 10.900 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * Wabco EBS (Electronic Braking System) * RDÜ (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer unit * Height-adjustable drawbar, hot-dip galvanized, adjustable by approx. 300 mm, with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 rear mechanical folding supports, hot-dip galvanized * 15-pin electrical connector * LED tail lights * Bolted underrun protection, hot-dip galvanized * Toolbox made of galvanized sheet steel, mounted on the right side * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel pallet 3-way tipper body * Continuous side walls with internal tube reinforcement at the top, without central stanchions, foldable with board wall spring lifter * Rear tailgate foldable and swinging with manual central locking * Bolted, hot-dip galvanized rear stanchions * In each corner: 1 x 5 t lashing point; laterally: 4 x 3 t lashing rings flush-mounted in the outer frame * 4 mm floor plate made of high-strength fine-grained steel * Net hooks, rear ramp mounting rail * Preparation for retrofitting sidewall extensions * Reinforced body with load securing certificate according to EN 12642 XL * Two-step entry on the left side for access assistance * 1 pair of aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t / pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment at the rear, recessed under the loading bed in the chassis * Axles, springs, air tanks, and landing gear painted in black * Chassis, drawbar, floor, front wall, folding supports hot-dip galvanized * Brand new vehicle, no first registration, covered by manufacturer's warranty * Tires: 385/55 R 22.5 * Sidewalls painted in RAL 9010 Pure White * Side panel painting in any RAL color available at extra cost Dkjdpfov Dz N Nex Ag Tog * Subject to errors and prior sale * Available from CW (calendar week)

Durumu: kullanılmış, azami yük ağırlığı: 13.860 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2022, yükleme alanı uzunluğu: 6.770 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 600 mm, yükleme alanı hacmi: 10 m³, Donanım: ABS, ? Galvanizli şasi ? Alçak bağlantı ? 50 mm çeki halkası ? Konteyner kilitleme ? Her iki tarafta 12 sabitleme halkası ? Geri görüş kamerası ? Kampana fren Dksdpfx Agoxb Iglo Tog ? Duomatic bağlantı ? ABS ? Havalı süspansiyon ? Takım sandığı ? EBS ? Destek ayakları ? İkiz tekerlekler ? BPW akslar Tüm bilgiler taahhütsüzdür / Ara satışa tabidir.

Durumu: yeni, azami yük ağırlığı: 10.900 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * Wabco EBS (Electronic Braking System) * RDÜ (Tyre Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizer assembly * Height-adjustable (approx. 300 mm) hot-dip galvanized drawbar with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical, hot-dip galvanized foldable props at the rear * 15-pin electrical connector * LED tail lights * Hot-dip galvanized bolted underrun protection * Toolbox made of galvanized sheet steel on the right side * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel pallet – three-way tipper body * Continuous side walls on top with internal tube reinforcement – foldable, without central stanchions, with drop side spring lifting assist * Rear tailgate foldable and swinging, with manual central locking * Hot-dip galvanized, bolted tail stanchions Dksdov El Tuspfx Ag Tsg * Each corner has one 5 t lashing point, and each side has four 3 t recessed lashing rings in the outer frame * 4 mm fine-grain steel floor plate * Net hooks, mounting rail at the rear for loading ramps * Prepared for later retrofitting of side wall extensions * Structure reinforced with load securing certificate according to EN 12642 XL * Two-step entry on the left side as access aid * One pair of aluminum loading ramps approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable storage compartment at the rear below the loading platform, integrated into the chassis * Axles, springs, air tanks, and landing gear painted black * Chassis, drawbar, floor, front wall, folding supports hot-dip galvanized * New vehicle, not yet registered, with manufacturer’s warranty * Tyres: 385/55 R 22.5 * Body panels painted to RAL 9010 pure white * Painting of side panels in any RAL color available at extra cost * Subject to errors and prior sale * Available from CW (calendar week)

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2024, * PT 30 Profile: * EBS (Electronic Braking System) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lifting and lowering feature as well as RtR valve * Smart-Board installed as infotool on the trailer (for axle load display—front and rear separated) * Tire pressure monitoring with display option in the truck via EBS signal, without installation on truck side * Side underrun protection * Swivel support legs at the rear chassis frame * Mechanically adjustable warning board packages front and rear * Front axle plastic quarter mudguards with splash protection * Rear axle straight galvanized steel skirts with splash protection * Reflective contour tape on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear Dedpfx Ajxptn Reg Tjkg * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Toolbox, galvanized sheet steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted on right side * Compartment in the bogie for accessories with folding lid, 2 container locks permanently installed (directly behind bogie platform) * ROBOT-welded anti-slip coating on the steel surface of the bogie platform (protruding weld beads) * Load securing package consisting of: 2 lashing rings (13.4 t) front left & right on the front wall carrier; front & rear, 1 pair each of UVV lashing rings (13.4 t); and 3 pairs per side of UVV lashing rings (10 t) – pivotable and lowerable, loadable in all directions and integrated in side frame; 3 each side stanchion pockets with simultaneous 2 t lashing capability * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear slope) * Widening planks stowed in the center of the loading platform * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically adjustable side-to-side * 4-way control block for retrofitting hydraulic ramp displacement * Chassis, bogie, folding outriggers, drop legs and loading ramps hot-dip galvanized * Axles, slewing ring, air tanks, and drawbar painted in a black shade * Loaded loading height approx. 910 mm +/- 20 mm with air suspension * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 38.900 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T5 Profile 50.0: * Wabco EBS (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake actuators * Drum brakes * 4 x 11-ton Gigant axles * Last axle is self-steering (Locking of the self-steering axle from the cab for maneuvering is possible without truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads * Air suspension with lift/lower system and RtR valve * 3rd axle liftable (ride height +30 mm when axle is lifted) * Forced unloading and forced lowering of the lift axle for maneuvering purposes (truck-side installation required), controlled depending on speed via the EBS electronics * Smartboard as info tool with pressure sensors for total axle load display by axle group Dksdexptn Dopfx Ag Tjg * Tire pressure monitoring with truck cabin display option via EBS signal (without truck-side installation) * Mechanical warning sign kit for 3 m overall width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable LED beacon at the rear * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, left side * Front fenders made of plastic, rear fender skirts made of galvanized sheet steel * Turntable platform front with 45° corners and 3 storage compartments with lockable folding lids (lids opening to rear) * Lowering of the low-bed platform by 500 mm to 6,280 mm incl. extended recessed neck 500 mm forward * Load securing package: 2 x 6.4 t lashing rings at the front corners, 2 x 13.4 t UVV-lashing rings at the front and rear side corners respectively, 5 x 10 t UVV-lashing rings each side (pivoting, lowering, multi-directional load capability), 4 stake pockets per side with simultaneous 2 t lashing capability, 1 x 16 t UVV-lashing ring on the rear cross member * Rubber covering on the folding ramp, driving slope and running surface of the low loader platform * Bamboo wooden insert between the side members in front of the excavator stick cradle * Extendable and foldable outriggers for 3 m overall width (plank holder under chassis, right side) * Continuous excavator stick cradle with reinforcement profile from last axle to end cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV-lashing rings laterally in the excavator stick cradle * Hydraulic folding ramp with dual line hydraulics and extendable pointed section approx. 4,650 x 720 mm including load-holding valves and hydraulic lateral shift * Hydraulic rear support * Hydraulic flow divider (for hydraulic pump output on truck of over 40 l/min up to max. 140 l/min) * Loaded loading height 890 mm +/- 20 mm via air suspension * Loading area above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm driving slope * Chassis, turntable, drawbar, extension brackets, and ramps hot-dip galvanized * Drawbar, axles, hydraulic axle supports, and air tanks painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 14/2026

Durumu: yeni, azami yük ağırlığı: 38.900 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T5 Profile 50.0: * Wabco EBS (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake actuators * Drum brakes * 4 x 11-ton Gigant axles * Last axle is self-steering (Locking of the self-steering axle from the cab for maneuvering is possible without truck-side installation, and additionally via a switch on the trailer); the lock must be disengaged before driving on public roads Dkedpel Tihuofx Ag Tjg * Air suspension with lift/lower system and RtR valve * 3rd axle liftable (ride height +30 mm when axle is lifted) * Forced unloading and forced lowering of the lift axle for maneuvering purposes (truck-side installation required), controlled depending on speed via the EBS electronics * Smartboard as info tool with pressure sensors for total axle load display by axle group * Tire pressure monitoring with truck cabin display option via EBS signal (without truck-side installation) * Mechanical warning sign kit for 3 m overall width * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment * LED lighting system 12/24 V * Removable LED beacon at the rear * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, left side * Front fenders made of plastic, rear fender skirts made of galvanized sheet steel * Turntable platform front with 45° corners and 3 storage compartments with lockable folding lids (lids opening to rear) * Lowering of the low-bed platform by 500 mm to 6,280 mm incl. extended recessed neck 500 mm forward * Load securing package: 2 x 6.4 t lashing rings at the front corners, 2 x 13.4 t UVV-lashing rings at the front and rear side corners respectively, 5 x 10 t UVV-lashing rings each side (pivoting, lowering, multi-directional load capability), 4 stake pockets per side with simultaneous 2 t lashing capability, 1 x 16 t UVV-lashing ring on the rear cross member * Rubber covering on the folding ramp, driving slope and running surface of the low loader platform * Bamboo wooden insert between the side members in front of the excavator stick cradle * Extendable and foldable outriggers for 3 m overall width (plank holder under chassis, right side) * Continuous excavator stick cradle with reinforcement profile from last axle to end cross member approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV-lashing rings laterally in the excavator stick cradle * Hydraulic folding ramp with dual line hydraulics and extendable pointed section approx. 4,650 x 720 mm including load-holding valves and hydraulic lateral shift * Hydraulic rear support * Hydraulic flow divider (for hydraulic pump output on truck of over 40 l/min up to max. 140 l/min) * Loaded loading height 890 mm +/- 20 mm via air suspension * Loading area above turntable: 2,600 + 390 x 2,520 mm * Low-bed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm driving slope * Chassis, turntable, drawbar, extension brackets, and ramps hot-dip galvanized * Drawbar, axles, hydraulic axle supports, and air tanks painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 14/2026

Durumu: yeni, azami yük ağırlığı: 27.940 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t axles * Air suspension with raise/lower function and RtR valve * Start-assist for maneuvering via EBS to the first axle (no truck-side installation) with lifted lift axle +30 mm ride height * Smart-Board information tool mounted on trailer with pressure sensors for total axle load display * Last axle configured as self-steering axle with electro-pneumatic steering lock * Steering lock for the self-steering axle can be activated from the tractor for maneuvering via EBS (without truck-side installation) * 2" king pin * 1 liftable axle * Side underrun protection * Front aluminum drop legs and rear swinging supports on chassis * Alcoa LVL One aluminum rims * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * 2 additional LED reversing lights * 2 LED work lights on trailer sides (no truck-side installation) * 7-pin socket at rear for overlength lighting * Side marker lights with indicator function * Tire pressure monitoring with in-cab display option via EBS signal (without truck-side installation) * Mechanically adjustable warning sign holder packages front and rear * Straight steel fenders * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated sheet steel (W = 2,480 mm x H = 500 mm x L = 665 mm) with top folding lid and side doors in the chamfered corners * On each side of the fifth-wheel platform, 400 mm high aluminum drop sides (RAL 9010 pure white), foldable and removable * Rear drop-in wall, 150 mm high * Rear slant on the fifth-wheel platform to the lowbed, approx. 700 mm long with checker plate and perforated strip for attaching aluminum loading ramps * Fifth-wheel and lowbed platforms with 50 mm clamped wooden planks * Tread plate above axles * Preparation for 3 receptacle shafts under the fifth-wheel platform for storing optional aluminum ramps * Swivel arm as a carrier for connecting lines from the truck to the trailer * Load securing package consisting of: perforated outer frame on the fifth-wheel platform, 45° bent with hole pattern for lashing equipment (2 t lashing force per point with min. 480 mm spacing), 2 x 6.3 t recessed lashing rings on each side, 1 x 16.5 t lashing ring per side on the slope from lowbed platform to fifth-wheel platform, 2 pairs of 16.5 t lashing rings in the lowbed platform (1 pair on the longitudinal beams after the step, 1 pair over the middle axle next to the longitudinal beam), 3 x 13.4 t lashing rings per side on the outer frame (1 at beginning of fifth-wheel frame step, 1 at start of ramp slope, 1 at end of ramp slope), 3 x 10 t lashing rings each side (2 between front wheel recess and 1st axle, 1 between 2nd and 3rd axle), 3 x 5 t lashing rings per side bolted to the outer frames of the wheel recesses (2 at the front, 1 at the rear) * Extended excavator arm resting area from the end of the last rigid axle over the steering axle to the rear cross member, continuous with internal reinforcement profile approx. W = 770 mm x Depth rear = 270 mm / Depth front 170 mm; 2 x 6.4 t lashing rings per side in the excavator arm rest * 2 wheel recesses per side, 390 mm deep and 640 mm wide, for transporting wheel loaders with a wheelbase of 3,000 – 3,590 mm and a tire diameter of 1,760 mm – with sliding covers * 2nd sliding cover... Dksdswh Hdxepfx Ag Tjg

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: * EBS (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 2 x 7 t Gigant axles Dkedpfxstr St Ho Ag Tjg * Parabolic springs with tandem balancing unit * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Drawbar height-adjustable by 300 mm with 40 mm flanged towing eye * Mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted right side * 15-pin electrical connector * Multi-chamber tail lights * Bolted underrun protection * Plastic quarter mudguards * Net hooks on the sides and rear in the central locking mounts, plus 2 pieces on the headboard * Main frame made of fine-grain steel * Steel pallet/tipper body with fixed front wall of smooth plate, continuous side panels – foldable without intermediate stakes with drop side counterbalance latches, and also pendulum mounted via manual central locking * Rear stakes bolted * Steel rear wall inserted in front of the ramps * Each corner with 1 x 5 t tie-down, plus 4 x 3 t lashing rings recessed into the external frame on each side * 4 mm fine-grain steel floor * Two-part mechanical grid ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (can be manually compressed down to 80 mm) * Chassis, drawbar, rear stakes, underrun protection, mechanical drop supports, and ramps hot-dip galvanized * Axles, springs, air tank, flange towing eye, and support winch finished in black paint * Drop sides and platform in RAL 9010 pure white * Painting of side panels and tipper body in a RAL color tone available for an extra charge * New vehicle with manufacturer's warranty * Errors and intermediate sale reserved * Available from week 07/2026

Durumu: yeni, azami yük ağırlığı: 10.950 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2026, * ETÜ-TA-ER 14.4 Flatbed Trailer: * TPMS (Tire Pressure Monitoring System) * EBS (Electronic Braking System) Djdov D Tbkopfx Ag Tjkg * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 ton BPW axles * Air suspension with lift and lowering function * Mechanically adjustable 3-meter warning panel sets at front and rear * Drawbar adjustable in height by 300 mm with 40 mm flanged towing eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in a B-length of approx. 8,080 mm) * Front support winch * Outward folding supports at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm, mounted on both left and right sides * Side underride guard * Rear underrun protection * Plastic quarter mudguards * 15-pin power connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (activated in reverse gear) * 1 removable LED beacon incl. holder at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m container external width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm; container locks extended = 2,819 mm (this dimension is not to DIN), with an overall width of 3,000 mm * Perforated outer frame, bent approx. 45 degrees, with 2 t lashing capacity every 480 mm, provision for 3 t drop-forged lashing rings every 600 mm – 5 x 3 t UVV lashing rings fitted per side; in the front and rear corners 1 x 6.3 t lashing ring each (front directly behind the container locks in the wooden floor and rear in the end cross member), various bores in front and rear cross member for 1.2 t lashing options * 1 pair of aluminum slide-in ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear accessible storage compartment recessed under the loading platform in the chassis * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air reservoir, front support winch and flanged towing eye painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available from CW 09/2026

Durumu: yeni, azami yük ağırlığı: 30.500 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with in-cab display option via EBS signal (no additional truck-side installation required) * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord installed as an infotool with pressure sensors for total axle load display per axle group * Side and rear reflective contour tape * Removable rear LED beacon * 15-pin electrical connector * LED tail lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height setting * Front closed individual plastic mudguards * Rear straight steel mud flaps, each with spray control (to suppress road spray) * Side underrun protection * Extension front of the turntable platform by approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lids open to the rear) * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm coniferous wood, and 60 mm coniferous wood in the low-loader platform * Outer planks of the loading ramps made of 50 mm hardwood * Lashing package includes: 2 lashing eyes 6.4 t at front left and right on the main frame of the turntable platform, 1 pair each of 13.4 t lashing rings at the front and rear sides on the outer frame, and 1 pair each of 10 t swivel- and lowerable lashing rings on each side, loadable in all directions and recessed into the outer frame, 5 t lashing rings bolted to the outer frame of the wheel recesses (2 each at the front and 1 at the rear wheel recess), 2 pairs of 6.4 t lashing rings on the side in the excavator boom rest * 11 pairs of folding outriggers for 3 m total width (not at the sloped rear) * Storage box (L = 2,470 x W = 570 x H = 250 mm) for steel extension planks, mounted crosswise to the loading area in front of the 1st rear axle * Excavator boom rest above the rear axle to the end of the ramp slope approx. 2,300 x 740 x 190 mm * On each side, 2 wheel recesses approx. 640 mm wide (front 340 mm deep, rear 220 mm deep) with retractable covers (storage for covers on the front of the turntable platform) for transport of wheel loaders with wheelbase 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip approx. 4,650 x 720 mm * Hydraulic side ramp shifting * Loading area over turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded platform height approx. 890 mm +/- 20 mm (incl. 860 mm ramp slope) * Chassis, turntable, folding outriggers, rear supports and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale reserved, * Available from CW 14/2026 * Sample images Dkedexmpydspfx Ag Tsg

Durumu: yeni, azami yük ağırlığı: 30.500 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Tire pressure monitoring system with display in the truck via EBS signal -no installation required on the truck- * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages at front & rear * SmartBord information tool mounted with pressure sensors for axle load display per axle group * Reflective contour tape on the sides and rear * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and continuously adjustable height * Closed plastic single mudguards at the front * Straight steel rear mudguards each with spray protection (anti-spray devices) * Side underrun protection * Front section ahead of the turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lid opens to the rear) * Chassis made from high-strength fine-grained steel * Floor above the turntable platform: 50 mm coniferous wood; on the low-bed platform: 60 mm coniferous wood * Outer planks of the drive-on ramps made from 50 mm hardwood * Load securing package consisting of: 2 lashing eyes, 6.4 t each, at the front left and right on the main frame of the turntable platform; 1 pair of 13.4 t lashing rings at the side, front and rear, on the outer frame; moreover, 1 pair of 10 t lashing rings per side, pivotable and lowerable, loadable in all directions and recessed in the outer frame; 5 t lashing rings screwed to the outer frame of the wheel recesses (2 each at the front and 1 at the rear wheel recess); 2 pairs of 6.4 t lashing rings at the side in the excavator arm storage area * 11 pairs of folding outriggers for 3 m overall width (not at the tapering rear end) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for widening planks, made of sheet steel, mounted transverse to the loading area in front of the 1st rear axle * Excavator arm trough above the rear axle to the end of the approach slope, approx. 2,300 x 740 x 190 mm * Each side with 2 wheel recesses, approx. 640 mm wide; front 340 mm deep, rear 220 mm deep, with sliding covers (storage for covers at the front on the turntable platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height (laden) approx. 890 mm +/- 20 mm (including 860 mm approach slope) * Chassis, turntable, folding outriggers, rear drop-down supports, and access ramps all hot-dip galvanized * Axles, air tanks, and drawbar painted in black * Tires: 235/75R17.5 Dkedpsxmpykofx Ag Tsg * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from KW 14/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders Dkodpfx Agstr Suce Teg * Drum brakes * 2 x 7-ton Gigant axles * Parabolic springs with tandem equalizer unit * Tire pressure monitoring with in-cab display via EBS signal (no truck-side installation required) * Height-adjustable drawbar, adjustable by 300 mm, with 40 mm flange towing eye * Mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * 15-pin electrical connector * Multi-chamber tail lights * Bolt-on underride guard * Plastic quarter mudguards * Net hooks on the sides and rear in locking bar mounts, plus 2 on the front bulkhead * Main frame made of fine-grain steel * Steel pallet platform with three-way tipper body, fixed smooth steel front wall, continuous drop sides (foldable without center posts), with drop side lift assist and swinging via manual central locking * Rear stanchions bolted * Steel rear wall inserted in front of ramps * Each corner with 1 x 5-ton lashing point, and each side with 4 x 3-ton lashing rings recessed in the outer frame * 4 mm fine-grain steel floor * Two-part mechanical grating loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (can be manually retracted up to 80 mm) * Chassis, drawbar, rear stanchions, underride guard, mechanical fall supports, and loading ramps hot-dip galvanized * Axles, springs, air tank, flange towing eye, and landing gear painted black * Drop sides and bed painted RAL 9010 pure white * Drop side and tipping platform painting in any RAL color available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from calendar week 07/2026

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton Gigant axles Dkedpfxjtr St Uo Ag Tsg * Parabolic leaf springs with tandem equalizing unit * Tire pressure monitoring with display capability in the truck via EBS signal, without requiring truck-side installation * Height-adjustable drawbar (300 mm) with 40 mm flanged towing eye * Mechanical support winch at front * 2 mechanical folding supports at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * 15-pin power connector * Multi-chamber taillights * Bolted underrun protection * Plastic quarter fenders * Mesh hooks on the sides and rear at central locking mounts, plus two on the bulkhead * Main frame made of fine-grain steel * Steel pallet body with 2-way tipper, fixed smooth steel bulkhead, continuous side walls—foldable without center posts with drop side spring-lifters, also swinging via manual central locking * Rear stanchions bolted * Steel rear wall inserted in front of ramps * Each corner fitted with one 5-ton lashing point, plus 4 x 3-ton lashing rings recessed in the outer frame per side * 4 mm floor made from fine-grain steel * Two-piece mechanical grate-type loading ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (can be manually collapsed to 80 mm thickness) * Chassis, drawbar, rear stanchions, underrun guard, mechanical drop supports, and ramps hot-dip galvanized * Axles, springs, air reservoir, flanged towing eye, and support winch painted in black * Drop sides and platform painted in RAL 9010 pure white * Alternative color painting of sidewalls and tipping platform in any RAL color available for extra charge * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from KW 07/2026 (calendar week 7 of 2026)

Durumu: yeni, azami yük ağırlığı: 10.950 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2026, * ETÜ-TA-ER 14.4 flatbed trailer: * RDÜ (tyre pressure monitoring system) * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t BPW axles * Air suspension with lifting and lowering system * Mechanically adjustable 3 m warning panel sets at front and rear * Drawbar adjustable in height by 300 mm with 40 mm flange eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting B-dimension of approx. 8,080 mm) * Support winch at front * Outward-folding rear supports * Plastic toolboxes approx. 750 x 350 x 300 mm, mounted left & right sides * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED lighting system 12/24V * 2 additional LED reversing lights at the rear (activated via reverse gear) * 1 removable LED beacon (including bracket) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m external container width) and lockable, lock dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN-compliant) for an overall width of 3,000 mm * Perforated outer frame bent at approx. 45 degrees with 2 t lashing capacity every 480 mm, possible installation of 3 t drop lashing rings every 600 mm - 5 x 3 t UVV lashing rings mounted on each side; at front and rear corners, each 1 x 6.3 t lashing ring (front directly behind container locks in the floor and rear in the end cross member), various bores for 1.2 t lashing points in front wall and end cross member Dedpev D Tbdjfx Ag Tskg * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Storage compartment below loading area embedded in chassis, accessible from rear * --- Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized --- * Axles, air tanks, front support winch, and flange eye painted in black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from KW 09/2026

Durumu: yeni, azami yük ağırlığı: 30.740 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ Tire Monitoring System * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering system and RtR valve * Smard board for load weight determination * Warning sign packages at front and rear * Reflective contour tape on sides and rear * Rotating beacon (removable) at rear * LED lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in basket design, located on the right side * Closed single plastic mudguard at the front * Straight steel mud flaps at the rear, each with spray suppression Dkodpfxol Tik No Ag Tjg * Side underrun protection * Turntable platform extended by 520 mm at the front, with 45° corners and 3 recessed, lockable compartments including covers * Chassis made of high-strength fine-grained steel * Floor over the turntable platform made of 50 mm softwood, and in the low-bed platform 60 mm softwood * Outer planks of the ramps made of hardwood * Four stake pockets per side (stakes not included) each with a 2 t lashing capability * Load securing package consisting of: 2 lashing eyes 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings at both the front and rear side frame, and 4 pairs of 10 t tilting and retractable lashing rings per side, flush mounted in the outer frame and loadable in all directions * 2 pairs of 6.4 t lashing rings at the excavator arm rest area * 8 pairs of galvanized fold-out outriggers for 3 m total width (not in rear slope) * Side extension planks stored in a compartment on the left * Excavator arm rest over the rear axle to end of rear slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm, incl. hydraulic ramp side shift & load holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Laden loading height: approx. 890 mm, +/- 20 mm (incl. 860 mm rear slope) * Flow divider installed * Chassis, turntable, access ramps, fold-out outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air reservoirs, and turntable painted black * Tires: 235/75 R 17.5 * New vehicle without registration, with manufacturer’s warranty * Errors and prior sale excepted * Available from calendar week 07/2025

Durumu: yeni, azami yük ağırlığı: 30.740 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * Smard board for payload determination * Warning panel packages front & rear * Reflective contour tape on sides and rear * Rotating beacon (removable) at rear * LED lighting * Straight drawbar with 50 mm towing eye and continuously adjustable height * Toolbox made of powder-coated steel plate and spare wheel holder in basket design, right side * Closed plastic single mudguard at the front * Rear straight steel mud flaps each with spray suppression * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. lids, lockable * Chassis made of high-tensile fine-grain steel * Floor over turntable platform made from 50 mm and in low-loader platform made from 60 mm coniferous timber * Outer planks of the ramps made from hardwood * Four stake pockets on each side (stakes not included), each with simultaneous 2 t lashing point * Load securing package including: 2 lashing rings 6.4 t at the front left and right on the main frame of the turntable platform * On the outside frame, 2 pairs of lashing rings 13.4 t front and rear, as well as 4 pairs per side of 10 t folding and lowering lashing rings * Loadable in all directions and integrated into the outer frame * 2 pairs of 6.4 t lashing rings at the excavator arm rest on the side * 8 pairs of galvanized folding extensions for 3 m overall width (not in the rear slope) * Widening boards stored on the left side in a storage compartment * Excavator arm rest above rear axle to end of rear slope approx. 2,100 x 740 x 190 mm Dkodpfel Tphrex Ag Tjg * Mechanical rear stabilizers * Hydraulic folding ramps with hydraulically extendable ramp end approx. 4,650 x 720 mm incl. hydraulically lateral ramp shift & load holding valve * Loading area above fifth wheel: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height when loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm rear slope) * Flow divider installed * Chassis, turntable, ramps, folding outriggers, and mechanical stabilizers hot-dip galvanized * Axles, drawbar, air tanks, and fifth wheel painted black * Tires: 235/75 R 17.5 * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale * Available from CW 07/2026