Kullanılmış Es-Ge Çalışma Platformu satın al (15)

Durum: ikinci el, azami yük ağırlığı: 35.480 kg, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 05/2026, bir sonraki muayene (TÜV): 05/2027, Donanım: ABS, Donanım Özellikleri Özeti Şasi: Yüksek kaliteli çelik profillerden kaynaklı yapı, yüksek nokta yüklerine dayanacak şekilde tasarlanmıştır. Profillerde ara destekler bulunur. Alt kısımda darbe emici, yaklaşık 700 mm genişliğinde, dış çerçeve UNP profili, yaklaşık 8 mm kalınlığında sürtünme plakası, ön kısımda yaklaşık 130 mm boşluk. Çekme Düzeni: 2 inç kingpin. Alt Koruma: Cıvatalı tip, AB yönetmeliklerine uygun. Yan Koruma: AB yönetmeliklerine uygun, alüminyum profillerden yapılmış, eloksal kaplama. Dingil Destekleri: 2 x 12 ton dingil destekleri, denge ayağı ve tek taraflı kumanda (sağ tarafta). Dingiller: 3 x 9 ton hava süspansiyonlu dingil grubu, disk frenler 22,5". Toplam hareket mesafesi yaklaşık 180 mm, hareket ettirme ve indirme mekanizması döner valf ile kontrol edilir. Fren Sistemi: Çift devre basınçlı hava fren sistemi, AB yönetmeliklerine uygun, EBS ve RSS ile, otomatik yüke bağlı regülasyon, yaylı akümülatörlü silindirler park freni olarak, değiştirilebilir şekilde kilitlenmiş bağlantı başları şasiye sabitlenmiştir, çekiciye bağlantı hattı olmadan. Lastikler: 6 adet, 385/55 R22,5 160J, çelik jant üzerinde 11,75 x 22,5 ET 120. Marka bizim seçimimiz. Lastik basıncı kontrolü (TPMS), EBS'nin CAN-Bus sistemi üzerinden. Çamurluklar: AB yönetmeliklerine uygun. Yedek Lastik Yuvası: Yok. Yük Sabitleme: - 9 çift katlanabilir bağlama halkası, eşit aralıklarla yerleştirilmiş, yaklaşık 5,0 ton çekme kuvveti. - 9 çift katlanabilir bağlama halkası, eşit aralıklarla yerleştirilmiş, yaklaşık 2,0 ton çekme kuvveti. - Dış çerçevede, yaklaşık 400-600 mm aralıklarla, bağlama kayışlarının takılması için delikler. Ön Panel: Güçlendirilmiş çelik yapı, sabit, yaklaşık 1.400 mm yüksekliğinde. İç kısmı yaklaşık 9 mm kalınlığında serigrafi baskılı panel ile kaplı (yaklaşık 1.250 mm yüksekliğinde). Zemin: Yaklaşık 28 mm kalınlığında Z tipi sert ahşap zemin, dış çerçeveye yerleştirilmiş, galvanizli omega çelik profillerle desteklenmiştir. Aydınlatma: AB yönetmeliklerine uygun, 24 volt, çok odacıklı farlar, LED yan işaret lambaları, LED konum lambaları (ön tarafta beyaz, arka tarafta kırmızı), plaka lambaları. Şerit takip lambaları LED. 1x15 ve 2x7 kutuplu bağlantı prizleri ön panelde. Donanım: Hsdpfezkx E Rox Ap Iefi - 2 adet tekerlek tutucu, tutucu ile birlikte. - Uyarı levhaları ECE 70. - Döner lamba tutucu, döner lambası ile birlikte. - Arka tarafta 2 adet kauçuk tampon. - Sağ tarafta katlanabilir ve uzatılabilir merdiven (platformsuz). - Delikli sacdan yapılmış, enine olarak yerleştirilmiş 1 adet açık kasa, yaklaşık 600 x 450 x 2.430 mm, galvanizli, dingillerin arkasında. Boya: Ön panel: RAL 3002 karmin kırmızısı. Şasi: Sıcak daldırma galvanizli. Dış çerçeve: Sıcak daldırma galvanizli + RAL 3002 karmin kırmızısı. Yan destekler: RAL 3002 karmin kırmızısı. Dingil destekleri: Alüminyum eloksal. Alt koruma: Beyaz (RAL 9016 trafik beyazı). Bağlantı parçaları: Galvanizli/KTL siyah. Jantlar: Gümüş. Kontur İşaretleme: Tamamı sarı renk. Ekipman dahil. Birinci dingil kaldırılabilir, tam otomatik, yüke bağlı kaldırma kontrolü. Dış çerçevede 10 çift yan destek cebi, eşit aralıklarla yerleştirilmiş. Yükleme alanına enine olarak yerleştirilmiş 4 sıra yan destek cebi. 20 adet galvanizli 80/50 borudan yapılmış yan destek, toplam uzunluk yaklaşık 1.200 mm. Ön panelde, 20 adet fişli yan destek için bir depolama alanı. 5 x 25 eloksal alüminyum kutu profilinden yapılmış yan duvarlar ve arka duvar, katlanabilir ve çıkarılabilir, çıkarılabilir Kinnegrip yan destekleri.

Durum: yeni, azami yük ağırlığı: 35.510 kg, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 3 dingil, Donanım: ABS, Tüm mevcut ve kısa sürede teslim edilebilecek araç stokumuzu web sitemizde bulabilirsiniz. Donanımdan bir alıntı. Tüm donanım talepler üzerine bildirilebilir. Şasi: * Yüksek kaliteli çelik profillerden yapılmış ve delinmiş profil enine kirişlere sahip kaynaklı yapı, yüksek noktasal yüke dayanacak şekilde tasarlanmıştır. Alt kısım genişliği yaklaşık 700 mm, dış çerçeve UNP profil olarak, şasi plakası yaklaşık 8 mm, ön boğaz yüksekliği yaklaşık 130 mm Çekme Donanımı: * 2 inç kral pimi Arka Alt Koruma: * Vidalı yapı, AB standartlarına uygun Yan Koruma: * AB standartlarına uygun, eloksallı alüminyum profillerden Çekici Ayakları: * 2 x 12 t çekici ayağı, ayarlı ayak tabanı ve sağ tarafta tek taraflı kumanda (FR sağ) Akslar: Hfedpfezhd Ncsx Ap Ioi * 3 x 9 t hava süspansiyonlu SAF marka aks grubu, 22,5 inç disk frenli * Toplam kaldırma kapasitesi yaklaşık 180 mm, kaldırma ve indirme el vanası üzerinden gerçekleşir Fren Sistemi: * AB standartlarına uygun çift devreli pnömatik fren sistemi, EBS ve RSS ile, otomatik yük bağımlı regülasyon, park freni olarak yaylı fren silindiri, yanlış bağlantıya karşı korumalı bağlantı başlıkları ön travers üzerine monte edilmiş, çekiciye bağlantı hattı yok Lastikler: * 6 adet, 385/55 R22,5 160J çelik jant (11.75 X 22,5 ET 120), marka tercihe bağlı * TPMS lastik basıncı kontrolü EBS'nin CAN-Bus sistemi üzerinden Çamurluklar: * AB standartlarına uygun Stepne Tutucu: * Yok Yük Sabitleme: * 9 çift katlanabilir bağlama halkası, eşit dağılmış, çekme kuvveti yaklaşık 5,0 t * 9 çift katlanabilir bağlama halkası, eşit dağılmış, çekme kuvveti yaklaşık 2,0 t * Dış çerçevede yaklaşık 400-600 mm arayla kayış takma delikleri Ön Duvar: * Takviyeli sabit çelik yapı, yüksekliği yaklaşık 1.400 mm * İç yüzeyde yaklaşık 9 mm kaymaz kontrplak kaplama (yaklaşık 1.250 mm yüksekliğinde) Zemin: * Dış çerçeveye gömülü yaklaşık 28 mm Z-tipi sert ağaç zemin, galvanizli omega çelik profilli Aydınlatma Sistemi: * AB standartlarına uygun, 24 Volt, çoklu bölmeli lambalar, LED yan markör lambalar, önde LED pozisyon lambaları (beyaz), arkada LED kontur işaretleyici, plaka lambaları * Şerit izleme LED lambaları * Ön travers üzerinde 1x15 ve 2x7 pinli prizler Donanım: * ECE 70 uyarı plakaları * Döner uyarı lamba tutucu dahil dönel uyarı lamba * Sağ arka köşede katlanır ve çekilir tırmanma merdiveni (platformsuz) * Delikli sacdan açık kutu, yanlamasına, yaklaşık 600 x 450 x 2430 mm, galvanizli, aksların arkasında Boya: * Ön duvar: RAL 5010 gentian mavisi * Şasi: sıcak daldırma galvanizli * Dış çerçeve: sıcak daldırma galvanizli + RAL 5010 gentian mavisi * Orta dikmeler: RAL 5010 gentian mavisi * SSV: Alüminyum eloksallı * Alt koruma: Beyaz (RAL 9016 trafik beyazı) * Takılı parçalar: galvanizli/KTL siyah * Jantlar: gümüş Aksesuarlar: * Birinci aks kaldırılabilir, tam otomatik yük bağımlı kaldırma kontrolü ile * Dış çerçevede 10 çift dikme cebi, eşit dağılmış * Yükleme alanı boyunca 4 sıra dikme cebi * 20 adet galvanizli borudan dikme, toplam uzunluk yaklaşık 1.200 mm * Ön duvarda içeride 20 adet fişli dikme için şarjör * 5 x 25'lik yan ve arka kapaklar, eloksallı alüminyum kutu profilden, katlanabilir ve çıkarılabilir, çıkarılabilir dikmeler * Sol ve sağ şasi altında yan kapaklar için magazin * Yan kapaklar için sürgü rayları * 1 x 40 ft veya 2 x 20 ft konteyner için arka hizalı konteyner kilitleri * 1 x 20 ft konteyner için orta kısımda konteyner kilidi * Arka lambalara entegre çalışma lambası (vitesle etkinleşir) * 2 adet paslanmaz çelik alet kutusu,

Durum: yeni, azami yük ağırlığı: 14.910 kg, toplam ağırlık: 20.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.550 mm, Donanım: ABS, Web sitemizde, hemen ve kısa süre içinde teslim edilebilecek araçların tamamını bulabilirsiniz. Donanımın bir özeti aşağıda verilmiştir. Komple donanım bilgisi isteğe bağlı olarak sunulabilir. Şasi: * Yüksek kaliteli çelikten enine traversli ve dış çerçeveli kaynaklı konstrüksiyon Rampa bölmesi: * Uzunlamasına taşıyıcılar arasında rampa bölmesi Alt koruma: * ECE R58-03 yönetmeliğine uygun sabit alt koruma * AB düzenlemelerine uygun yan ve alt koruma Ön destek: * Çift hızlı kriko ayakları ile ön destek (2 x 12 t) Arka destek: * Sabitlenebilir düşme ayakları ile arka destek Akslar: * 2 x 10 t SAF aks, kampanalı fren, düşük bakım gerektiren havalı süspansiyon aksı, yaklaşık 180 mm toplam kaldırma/indirme mesafesi, asbestsiz fren balataları, aks başına 10.000 kg taşıma kapasitesi * Çelik hava deposu Hfjdpszgqncefx Ap Iei * Merkezleme ile tekerlek bağlantısı Lastikler: * 235/75 R 17,5 lastikler, çelik disk jantlarda, 8'li, marka tercihi bize ait * Lastik basınç izleme sistemi, düşük basınç uyarısı Paspaslık: * Plastik çamurluklar, çamur tutucu Yük emniyeti: * Dış şaseye eşit aralıklı 8 t kapasiteli 6 çift sabitleme noktası * Eğik ve delikli dış şase, kapalı yan tahtada sabitleme kancaları için * 3 çift kaynaklı dikme cepleri, yaklaşık 80 x 50 mm ölçüsünde, eşit mesafeli Fren sistemi: * EG yönergesine uygun otomatik yük sensörlü iki hatlı havalı fren sistemi, yay tahrikli park freni (1 boşaltma valfi dahil), EBS hava bağlantıları kırmızı/sarı spiral hortumlu, römork için Zemin: * Yaklaşık 30 mm kalınlığında z-profilli sert ağaç zemin Ön duvar: * Çıkarılabilir yan panelli, yaklaşık 600 mm yüksekliğinde Aydınlatma/Elektrik: * Elektrik: StVZO'ya uygun 24 volt aydınlatma sistemi * Çok odacıklı, tamamen LED arka lambalar, entegre balastlı ve yan işaret lambasıyla birlikte * Römorkta ayrıca şerit takip lambaları * Ön alt kısımda beyaz pozisyon lambaları (AB ve İsviçre onayı gerektirir) Elektrik bağlantıları: * Römork için 2x7 pin ve 1x15 pin bağlantı * Bağlantı levhası ön travers üzerinde, kablolar sabit, ayrı bağlantı olmadan, sol tarafta besleme bağlantıları Aksesuar: * StVZO'ya uygun takozlar * Arkada takılabilir dönerli uyarı lambası * Ekstra 40’lık çekme tertibatı teslimatı (azami GG 13.500 kg) Boya: * Alt yapı galvanizli + toz boya * Şasi yüksek kaliteli sıcak daldırma galvanizli ve ardından toz boyalı; optimal korozyon koruması için. Yüzeyde galvanizden kaynaklı izler olabilir * Standart üst yapı boya Renkler: * RAL 3002 karmen kırmızısı * Orta ve köşe dikmeleri: KTL + toz boya, RAL 3002 karmen kırmızısı * Yan paneller: RAL 3002 karmen kırmızısı * Çekme borusu: sıcak daldırma galvanizli * Şasi büyüklüğü ve galvanizleme yöntemi nedeniyle yüzeyde hatalar (ör. sıcak çinko kabarcıkları, artçılar, çinko sarkmaları, deformasyon vb.) olabilir. Bunlar üzerinde kontrolümüz yoktur ve ürünün görselliğinde yasal kusur teşkil etmez Kontur işaretleme: * Yanlarda sarı reflektif kontur işareti * Arkada çevreleyen sarı reflektif kontur işareti Opsiyonel aksesuar: * Arkada yaklaşık 800 mm uzatmalı, tekerlekli sabit alt korumalı

Durum: ikinci el, Fonksiyonellik: tamamen fonksiyonel, boş ağırlık: 9.000 kg, azami yük ağırlığı: 29.000 kg, toplam ağırlık: 38.000 kg, ilk tescil: 08/2020, renk: kırmızı, Üretim yılı: 2020, ES-GE 2-Axle Lowbed, non-extendable, Tridec Steering Gross weight: 38,000 kg Axle load (2 x 10,000 kg): 20,000 kg Fifth-wheel load: 18,000 kg Unladen weight +/- manufacturer's tolerance: approx. 9,000 kg Payload: approx. 29,000 kg Overall length: approx. 13,650 mm Overall width: approx. 2,540 mm Loading platform length: approx. 13,200 mm Loading platform width: approx. 2,540 mm Front overhang: approx. 1,200 mm Front radius: approx. 1,750 mm Swing radius (tractor unit): approx. 2,100 mm Coupling height: approx. 1,150 mm B-dimension: approx. 12,000 mm Raised bed length: approx. 3,700 mm Raised bed loading height: approx. 1,480 mm Lowbed length: approx. 6,500 mm Lowbed loading height: approx. 250 mm Lowbed ground clearance: approx. 100 mm Loading height above axle assembly: approx. 3,000 mm Tractor unit details A-dimension: approx. 4,500 mm Coupling height: approx. 1,150 mm Swing radius: approx. 2,100 mm Chassis: - Chassis manufactured from high-quality fine-grain steels - Lowbed in rigid construction - Axle assembly not detachable - Without excavator trough Kingpin - 2" kingpin Landing legs - Without front landing gear Axles - 2 x 10,000 kg axles (17.5"), technically rated at 12,000 kg each – brand: Gigant - Enclosed drum brakes, asbestos-free brake linings - Automatic slack adjusters, centralizing device - Axle spacing approx. 1,360 mm Suspension - Air suspension with lift and lower system - Second ride height for air suspension (+ approx. 30 mm) Steering - Hydraulic axle steering - All axles steered, make "Tridec" Tyres - 9 tyres 245/70 R 17.5, load index 146/146 F – tyre brand: Continental - Steel rims Brakes - Dual-line air brake system according to EC directive, make "Knorr" - Automatic load-dependent brake force regulator - Operated via standard air couplings, red/yellow, acc. ISO 1726 - Electronic brake system (EBS), 7-pin socket acc. to ISO 7638, mounted at the front, acc. to EU regulations. With ABS 4S/2M - With RSS (Roll Stability Support) - Parking brake with spring-loaded cylinder - 4 wheel chocks with holders - Without connecting hoses (Wendeflex) to tractor - Aluminium air tanks - TIMG2 (Trailer Information Module) installed for current axle load readout Rear underrun protection - Integrated into the rear end plate Side frame - Side frames made of UNP steel, approx. 200 mm Load securing - 13 lashing points per side with 13,400 kg tensile force, foldable outwards, mounted on the outer frame - 1 pair of lashing rings with approx. 13,400 kg lashing capacity in the rear area of the gooseneck, approx. 400 mm above the ground - 1 pair of lashing rings with approx. 13,400 kg tensile force at the rear of the lowbed at the vertical neck Hjdpfsu U Np Tox Ap Iofi - 7 stake pockets per side on the inside of the outer frame for bolsters approx. 80x50x4 mm, evenly distributed along the loading platform - 6 stake pockets per side welded externally onto the longitudinal beam Floor - Approx. 28 mm hardwood floor with Omega profiles, fitted between the longitudinal beams - Chequer plate (approx. 8/10 mm) above axle assembly Bulkhead - Designed as a toolbox with lid, approx. D 400 x H 450 mm, spanning the full width of the loading platform, corners chamfered Side panels - 3 removable, anodised side panels on the gooseneck, approx. 2,440 x 400 mm - Removable stanchions at rear, galvanized Finishing - All steel parts shot-blasted - Chassis spray-galvanized Paintwork - Primer and single-color coating in RAL 3002 flame red - Axles and landing gear KTL-c

Durum: ikinci el, azami yük ağırlığı: 32.610 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2023, bir sonraki muayene (TÜV): 11/2025, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Complete specifications available upon request. Chassis: * Welded construction made of high-quality steel profiles with through-profile crossmembers, designed for high point loads Fifth wheel coupling: * 2-inch kingpin Underrun protection: * Bolted design, compliant with EU regulations Side underrun protection: * Compliant with EU regulations Landing gear: * 2 x 12 t landing legs with compensating foot and single-sided operation on the right in driving direction Axles: * 3 x 9 t air suspension axle assemblies * Disc brakes * Brand: Gigant Hjdpfjwyhy Eox Ap Iofi Brake system: * Dual-line compressed air brake system according to EU regulations with EBS and RSS, automatic load-dependent control * Spring-type cylinders as parking brake * Mistake-proof coupling heads permanently mounted on the front crossmember, without connecting line to the towing vehicle * Brand: Wabco Tyres: * 6 units, 385/55 R22.5 160J on 11.75 x 22.5 steel rims, offset 120 Mudguards: * Compliant with EU regulations, PVC mudguards before and after the axle assemblies Spare wheel carrier: * 1 double basket with mounting material for one spare wheel with offset 120 Load securing: * 9 pairs of foldable lashing rings, evenly distributed, tensile strength approx. 8.0 t * 8 pairs of foldable lashing rings, evenly distributed, tensile strength approx. 2.5 t * Holes for tension belts in the outer frame, approx. every 500 mm Front wall: * Reinforced steel construction, fixed * Interior covered with approx. 9 mm phenolic plywood (approx. 1,250 mm high) Floor: * Approx. 28 mm Z-hardwood floor recessed in the outer frame Lighting system: * Compliant with EU regulations, 24 Volt, with multi-chamber lights * LED side marker lights * LED front position lights (white) * LED rear outline marker lights * Number plate lights * 1x 15-pin and 2x 7-pin socket connections on front crossmember Paintwork: * Chassis and front wall cleaned by sandblasting, primed and painted in single color * Chassis: RAL 3002 Carmine red * SSV: Aluminium anodized * Underrun protection: white RAL 9010 * Attachments: galvanized/black KTL * Rims: silver Incl. special equipment: * First axle liftable, with fully automatic, load-dependent lift control * 10 pairs of stanchion pockets in the outer frame, evenly distributed * 4 rows of stanchion pockets across the loading area * 20 stanchions made of galvanized tube 80/50, total length approx. 1,000 mm * Magazine for 20 plug-in stanchions inside the front wall * Container locks for 1 x 40' and 2 x 20' containers, flush with rear * Container locking for 1 x 20' container in the center * Work lamp on lamp bracket (switched via reverse gear) * 2 PVC toolboxes, approx. 660 x 400 x 500 mm

Durum: ikinci el, Üretim yılı: 2000, ES-GE 4.vod-25-40.4-h13. Hjdpfxjy Ay Efj Ap Isfi Baujahr: 2000. 10-Tonnen-SAF-Achsen. Eigengewicht: 16.840 kg. Nutzlast: 45.660 kg. Gesamtgewicht: 62.500 kg. Sattellast: 22.500 kg. 2-fach ausziehbar: 10,4 Meter + 9,3 Meter = Gesamt 19,7 Meter ausziehbar. Hydraulikversorgung über NATO-Kupplung vom Zugfahrzeug. Servolenkung mit 4 gelenkten Achsen. Luftfederung. Werkzeugkästen. Abmessungen Ladefläche: Länge: 16.000 mm. Breite: 2.550 mm. Höhe: 1.500 mm. Sattelhöhe: 1.250 mm. Bereifung: 275/70R22,5, Profil 80%. Deutscher Auflieger! ID-Nr.: 487. Die Allgemeinen Geschäftsbedingungen der Firma Heinhuis gelten für alle Anzeigen, Angebote und Offerten sowie für sämtliche Verträge und den ihnen vorausgehenden Verhandlungen. Mit einer Kontaktaufnahme erkennen Sie die Gültigkeit der Allgemeinen Geschäftsbedingungen an und bestätigen deren Kenntnisnahme. Unsere Preise sind Netto-Exportpreise. = Weitere Informationen = Baujahr: 2000 Leergewicht: 16.840 kg Zuladung: 45.660 kg zGG: 62.500 kg Ausziehbarer Aufbau: Ja = Firmeninformationen = Für weitere Informationen: WhatsApp:

Durum: yeni, azami yük ağırlığı: 36.200 kg, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete inventory of immediately and soon available vehicles on our website. Excerpt from the equipment. Full specification available upon request. Chassis: * Welded construction made of high-quality steel profiles with through-profile cross members, designed for high point loads Hedpfx Ajzahp Eep Ijfi * Underrun nose approx. 700 mm wide * Outer frame as UNP profile * Wear plate approx. 8 mm * Neck height at the front approx. 130 mm * Coupling device with 2-inch kingpin * Bolted underrun protection, compliant with EU regulations * Side underrun protection, compliant with EU regulations, made of anodised aluminium profiles * Landing gear: 2 x 12 t * Landing gear with compensating foot and single-sided operation on the right (FR) * Axles: 3 x 9 t air suspension axle units * Disc brakes 22.5, total stroke approx. 180 mm * Lift and lowering mechanism via rotary slide valve Brake System: * Dual-circuit air brake system compliant with EU regulations, with EBS and RSS, automatic load-dependent control * Spring-loaded cylinders as parking brake * Swapped-proof coupling heads securely mounted on the front cross member, no connecting line to the tractor unit Tyres: * Sixfold, 385/55 R22.5 160J mounted on 11.75 x 22.5 steel rims, ET 120, make as per our choice * Tyre Pressure Monitoring System (TPMS) via EBS CAN-Bus system Load Securing: * 9 pairs of foldable lashing rings, evenly distributed, tensile force approx. 5.0 t * 9 pairs of foldable lashing rings, evenly distributed, tensile force approx. 2.0 t * On the outer frame, holes every approx. 400–600 mm for securing straps Front Wall: * Reinforced steel construction, fixed, approx. 1,400 mm high * Interior covered with approx. 9 mm phenolic board (approx. 1,250 mm high) Floor: * Approx. 28 mm Z-hardwood floor recessed in the outer frame with galvanised omega steel profiles Lighting System: * According to EU specifications, 24 Volt, with multi-chamber lights * LED side marker lights * LED position lights white at the front * LED outline markers at the rear * Number plate lights * Lane departure LED lights * 1x 15-pin and 2x 7-pin sockets on the front cross member Equipment: * 2 wheel chocks with holder * ECE 70 warning plates * Holder for beacon including beacon * 2 rubber bumpers at rear * Rear right access ladder, foldable and extendable (without platform) * 1 open box made of perforated sheet steel, transverse to the direction of travel, approx. 600 x 450 x 2,430 mm, galvanised, located behind the axles Paintwork: * Front wall: RAL 3002 carmine red * Chassis: Hot-dip galvanised * Outer frame: Hot-dip galvanised + RAL 3002 carmine red * Side underrun guard: Aluminium, anodised * Underrun protection: white (RAL 9016 traffic white) * Mounted parts: galvanised/KTL black * Rims: silver Including special accessories: * First axle liftable, with fully automatic, load-dependent lift control * 10 pairs of stake pockets in the outer frame, evenly distributed * 4 rows of stake pockets across the loading platform * 20 stakes made of galvanised pipe 80/50, total length approx. 1,200 mm * Stake rack for 20 plug-in stakes mounted inside the front wall * Container locks for 1 x 40’ or 2 x 20’ containers, flush with rear * Container locks for 1 x 20’ container in centre position * Work spotlight on lamp bracket (switched via reverse gear) * 2 stainless steel toolboxes, approx. 600 x 500 x 500 mm, one on each side

Durum: yeni, azami yük ağırlığı: 34.350 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full specification on request. Chassis: * Welded construction from high-quality steel profiles with punched cross members, suitable for high ground or point loads, featuring a heavy-duty outer frame * Rear loading floor as a steel welded construction, equipped with two welded-in outer driving rails made from 5-hole steel plate (hole pattern system Lohr/Rolfo), hydraulically lowerable over a length of approx. 2,250 mm by approx. 350 mm * Rear of vehicle incorporates a hydraulically extendable loading table (approx. 1,500 mm) as a steel welded structure with 5-hole steel plate (hole pattern system Lohr/Rolfo) cover, lamp mount, and 2 ramp compartments with ramp supports * Rear section operated and controlled via an electric-hydraulic power unit, mounted in a stainless steel box on the left side of the chassis, controlled by radio remote control * Power supply via the towing vehicle’s battery (NATO socket on the front wall, no connecting cable to the tractor) Kingpin: * 2-inch kingpin, replaceable from below Underrun Protection: * According to EU standards, fixed mounted Landing Legs: * 2 x 12 t landing gears with 2-speed gearbox Axles: * 3 x 9 t air suspension axle units * Make: SAF with disc brakes approx. 370 x 45 mm * ABS * 10-hole wheel connection, centered, ET120 Hfsdpfxjwt Iylj Ap Ioi * Total air suspension stroke approx. 310 mm (raising approx. 220 mm, lowering approx. 90 mm) * Air suspension control via hand lever with stop function Lift Axle: * 1st and 3rd axles liftable automatically, additionally switchable via controls on the chassis frame or via PIN 12 of the lighting socket Tyres: * 6x, 445/45R19.5, on 14.00x19.5 rims, 10-hole ET120 fitted Mudguards: * According to EU standards, 1/4 PVC mudguards * 1st axle front and rear, 2nd and 3rd axle rear Brake System: * Make: Wabco * Dual-line brake system according to EU standards, with EBS and automatic load sensing * Spring actuators serving as parking brakes on 2 axles * Interchange-proof coupling heads fixed to the front cross member, without connecting line to the tractor Lighting System: * According to EU standards, 24 Volt, * Multi-chamber rear lights * License plate lights * LED side marker lamps * LED position lamp (white) front and LED lane marker lights on the rear * 15-pin socket as well as 2x 7-pin sockets fixed on the front cross member, no connecting lines to the tractor Load Securing: * 9 pairs of folding lashing rings evenly distributed, lashing capacity approx. 8 t * 8 pairs of folding lashing rings evenly distributed, lashing capacity approx. 2.5 t * 2 pairs of folding lashing rings at vehicle rear, lashing capacity approx. 2.5 t * Drilled holes in outer frame every approx. 500 mm for tie-down straps Stake Pockets: * 16 detachable stakes approx. 100/40 mm, usable length approx. 800 mm Stake Pocket Recesses: * Each side recessed with 8 stake pockets in the outer frame * 4 rows of stake pockets transverse to the loading platform Floor: * Approx. 28 mm Z-hardwood floor embedded in the outer frame Front Wall: * Enclosed front wall * Storage depot for 16 detachable stakes approx. 100/40 mm * Front wall bolted to head frame Equipment: * 2 wheel chocks with brackets * 2x PVC toolboxes, approx. 600/400/500 mm * Bracket for revolving beacon at rear incl. lamp * 2 LED reversing lights (at rear) * 2 aluminium loading ramps, approx. 1,550 x

Durum: yeni, azami yük ağırlığı: 37.350 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You will find our complete range of vehicles with units available immediately and at short notice on our website. Partial list of equipment. Full equipment details on request. Chassis: * Welded construction made from high-quality steel profiles with pass-through cross members for high surface and point load capacity, featuring a heavy-duty outer frame * Rear loading deck constructed as a welded steel structure with two welded-in drive tracks on the outside made of 5-hole steel plate (hole pattern System Lohr/Rolfo), hydraulically lowerable by approx. 350 mm over a length of approx. 2,250 mm * At the rear of the vehicle: integrated hydraulically extendable loading platform (extendable by approx. 1,500 mm) as welded steel construction with 5-hole steel plate (hole pattern System Lohr/Rolfo) cover, including lamp mount, 2 ramp compartments, and ramp supports * Rear operation and control via an electric-hydraulic power pack mounted in a stainless-steel box on the left side of the chassis, including radio remote control * The power supply comes from the towing vehicle’s battery * NATO socket on the front wall, without connection cable to the truck tractor Coupling system: * 2" kingpin, replaceable from below Underrun protection: * Meets EU regulations, permanently mounted Landing gears: * 2 x 12 t support legs with two-speed gearbox Axles: * 3 x 10 t air suspension axle sets, SAF brand with disc brakes size approx. 370 x 45 mm, ABS, 10-hole centric wheel connection ET120, total air suspension stroke approx. 200 mm (raise approx. 140 mm, lower approx. 60 mm), air suspension controlled via manual control with stop function Steering axle: * Third axle as trailing steering axle, with manual and automatic reverse lock Lift axle: * First axle automatically liftable, can also be operated via control on the chassis frame or via pin 12 of the light socket Hedjy Up S Sepfx Ap Iofi Tyres: * 6 units, 445/45R19.5, selected brand, mounted on 14.00x19.5 wheels, 10-hole ET120 Mudguards: * In accordance with EU regulations, 1/4 PVC mudguards in front of and behind the wheels on first axle front and rear, and on second and third axles at rear Spare wheel holder: * Not included Brake system: * Two-line brake system per EU regulations with EBS, automatically load-sensitive control * Spring-loaded parking brake acting on 2 axles, anti-mix-up coupling heads fixed on the front cross member, no connecting line to the truck tractor. Manufacturer: Wabco Lighting system: * In accordance with EU regulations, 24 volt, multi-chamber tail lights, license plate lights, LED side marker lights, white LED position lights at front and LED lane assist lights at rear, 15-pin socket and 2 x 7-pin sockets fixed on the front cross member, no connecting cables to the tractor unit Load securing: * 9 pairs of folding lashing rings, evenly distributed, tensile force approx. 8 t * 7 pairs of folding lashing rings, evenly distributed, tensile force approx. 2.5 t * 2 pairs of folding lashing rings at rear of vehicle, tensile force approx. 2.5 t * Outer frame equipped with drilling points for tie-down straps approx. every 500 mm Stake pockets: * 16 removable stakes approx. 100/40 mm, with usable length approx. 800 mm Stake pockets: * 8 pockets per side recessed into outer frame * 4 rows of stake pockets across the load floor Floor: * Approx. 28 mm Z-hardwood floor recessed into outer frame Front wall: * Solid front wall, storage for 16 removable stakes approx. 100/40 mm * Front wall screwed onto

Durum: ikinci el, dingil konfigürasyonu: 3 aks, ilk tescil: 04/2007, toplam uzunluk: 13.400 mm, toplam genişlik: 2.550 mm, süspansiyon: hava, lastik boyutu: 205/65R17.5, dingil mesafesi: 9.800 mm, renk: beyaz, Üretim yılı: 2007, Donanım: ABS, SAF axle. 2 x trailing steer axles. Extendable. Lifting roof. Sliding roof. Loading platform length: 910 cm. Floor height: 80 cm. Neck length: 390 cm. = Further Information = Axle configuration Tire size: 205/65R17.5 Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Twin tires; Tire tread left inner: 30%; Tire tread left outer: 30%; Tire tread right inner: 30%; Tire tread right outer: 30% Rear axle 2: Twin tires; Tire tread left inner: 30%; Tire tread left outer: 30%; Tire tread right inner: 30%; Tire tread right outer: 30% Rear axle 3: Twin tires; Tire tread left inner: 30%; Tire tread left outer: 30%; Tire tread right inner: 30%; Tire tread right outer: 30% Rear axle 4: Twin tires; Tire tread left inner: 40%; Tire tread left outer: 40%; Tire tread right inner: 40%; Tire tread right outer: 40% Weights Unladen weight: 9,940 kg Payload: 37,660 kg Gross vehicle weight: 47,600 kg Identification Type number: 4STL48 / 4 AXLE / SLIDING ROOF / = Company Information = Hfedpfx Apsy N Aw Ro Ioi ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN) Wouter Greutink (NL-DE-EN-ES-IT) We speak Russian. We always strive to provide correct information, however, no rights can be derived from the published texts.

Durum: yeni, azami yük ağırlığı: 15.825 kg, toplam ağırlık: 20.500 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.550 mm, yükleme alanı genişliği: 2.550 mm, toplam genişlik: 2.550 mm, Donanım: ABS, Our complete range of vehicles, including those available for immediate or short-term delivery, can be found on our website. This is an excerpt from the equipment features. Full equipment details available on request. Chassis: * Steel welded construction with welded longitudinal beams and punched Z-cross members, narrow cross member spacing for high floor load capacity * Ramp storage between the longitudinal beams behind the axle assembly, two insertion pockets for drive-on ramps under the loading floor, closure plate in the rear head frame Underrun Protection: * In accordance with EU regulations Front Landing Legs: * Single-sided operated landing legs Rear Support: * Two adjustable drop-down supports Axles: * 2 x 10 t air suspension axle unit, SAF make, drum brakes approx. 300 x 200 mm, wheel connection with center mounting for twin tyres, ABS, total air suspension lift approx. 200 mm, lift approx. 140 mm, lower approx. 60 mm, controlled by manual lever with detent function Tyres: * 8-fold, 235/75R 17.5 - make at our discretion, mounted on steel rims 6.75 x 17.5, with offset Splash Protection: * PVC splash guards in front of and behind the axles in accordance with EU regulations Load Securing: * Drill holes for lashing straps every approx. 150 mm on the outer frame, lashing capacity approx. 2.5 t (lashing straps can be hooked in even with drop sides closed, chamfered outer frame) * 6 pairs of folding lashing rings, evenly distributed, lashing capacity approx. 8 t * Stake pockets for 80/50 plug-in stakes: 3 pairs of stake pockets evenly distributed on the outer frame Brake System: * Pneumatic brake system in accordance with EU with EBS * Two coiled connecting lines to the towing vehicle with red/yellow coupling heads * Spring-loaded parking brake on one axle Floor: * Approx. 28 mm Z-hardwood floor flush-fitted in the outer frame Front Wall: * Detachable 25 mm drop side Lighting System: * Lighting system in accordance with EU regulations, 24 Volt, multi-chamber rear lights, license plate lights, side marker and outline lights at the rear, terminal box on the left of the drawbar including connection cable with 15-pin and 2 x 7-pin connectors Accessories: * 2 wheel chocks with holders * Detachable beacon at the rear * Delivery includes an additional 40 mm towing device (GVW max. 13,500 kg) Paintwork: * Chassis shot-blasted, cleaned and high-quality hot-dip galvanized according to the latest technological standards * Superstructure parts cleaned, primed, and hot-dip galvanized Chassis: * Hot-dip galvanized + RAL 3002 carmine red * Drop sides: RAL 3002 carmine red * Kinnegrip stakes: RAL 3002 carmine red * Hubs: KTL black * Underrun protection: RAL 9010 pure white * Rims: RAL 9006 silver * Mounted parts: galvanized / KTL black Contour Marking: Hfsdpfsy Auhbjx Ap Isi * In accordance with EU, yellow on sides and rear Including Special Equipment: * Rear extension by approx. 800 mm including underrun protection, extendable loading platform, load capacity approx. 2 t, locking at approx. 200 mm intervals * Mechanically length-adjustable rigid drawbar, 6 x approx. 100 mm increments, with bolted towing eye approx. 50 mm as per DIN 74053 * 4 rows of stake pockets across the loading area, evenly distributed * 12 plug-in stakes made of galvanized tubular steel, approx. 80/50/4 mm, approx. 1,000 mm long * Container locks for 1x20' container, extendable to approx. 2,820 mm, according to ISO 1496, EN 284, or EN 452 * 1 pair of aluminum loading ramps, load capa

Durum: yeni, azami yük ağırlığı: 32.155 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Selection of features. Full specification on request. Chassis: * Welded structure made of high-quality steel profiles with punched profile cross members. Designed for high point loads. Coupling system: * Fifth wheel plate with 2-inch kingpin. Underrun protection: * In accordance with EC regulations, bolted design. Hfodjy Auhzjpfx Ap Ioi Side underrun protection: * In accordance with EC regulations. Landing legs: * 2 x 12 t landing legs with compensating foot and single side operation (right side in direction of travel). Axles: * 3 x 9 t air suspension axle units, brand SAF, with disc brakes approx. 430 x 45 mm, centered wheel hub ET120, ABS, total air suspension travel approx. 180 mm (lifting approx. 110 mm, lowering approx. 70 mm) * Air suspension controlled via manual control valve with stop function. Steering: * Last axle forced-steered via rod linkage. Axle lift: * First axle liftable, with fully automatic load-dependent lift control. Brake system: * Two-line pneumatic brake system according to EC with EBS and RSS, automatic load-sensing control, spring-loaded cylinders for parking brake, anti-interchange couplings mounted fixed to front cross member, no connecting line to tractor unit. * Manufacturer: Wabco Tyres: * 6 units, 385/65 R22.5 160J on 11.75 x 22.5 ET 120 rims – brand of our choice. Incl. tyre pressure monitoring, tyre pressure display in cab (prepared by vehicle manufacturer). Mudguards: * In accordance with EC regulations, 1/4 PVC mudguards front and rear of axle units. Load securing: * 9 pairs of foldable lashing rings, evenly distributed (traction force approx. 8.0 t) * 8 pairs of foldable lashing rings, evenly distributed (traction force approx. 2.5 t) * External frame features a lashing point approx. every 500 mm for tension belts (lashing can be applied with side walls closed; outer frame with chamfered design). Stake pockets: * 10 pairs of stake pockets evenly distributed in outer frame * 4 rows of transverse stake pockets across the loading area * Plug-in stanchions: 20 pcs, galvanized pipe approx. 80/50 mm, total length approx. 1,000 mm * Magazine for 20 plug-in stanchions mounted inside front bulkhead. Front bulkhead: * Reinforced fixed steel construction, interior paneled with approx. 9 mm phenolic plywood (height approx. 1,250 mm) Floor: * Approx. 28 mm Z-hardwood floor recessed into the outer frame. Sideboards: * 4 x 25 side panels and rear wall made from anodized aluminum hollow profiles, foldable and removable, removable Kinnegrip stanchions. * Sideboard and stanchion magazine: under chassis * Insertion rails on left and right for sideboards and stanchions Lighting system: * In accordance with EC regulations, 24 Volt with multi-chamber lights, LED side marker lamps, LED front position lamps (white), LED rear outline lamps, license plate lamps * 1 x 15-pole and 2 x 7-pole socket connections on front cross member. Equipment: * Two wheel chocks with holders * Warning boards according to ECE 70 * Work light mounted on light bar (switches on via reverse gear) * Holder for beacon at rear incl. beacon * 2 x stainless steel toolboxes, approx. 600 x 500 x 500 mm Painting: * Chassis and front bulkhead cleaned by sandblasting, primed and finished in a single color * Chassis: hot-dip galvanized + RAL color of choice * Front bulkhead: RAL color of choice * Sideboards: anodized aluminum * Front bulkhead stanchions: hot-dip galv

Durum: yeni, azami yük ağırlığı: 39.070 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. Excerpt from the equipment list. Full specification available upon request. Chassis: * Welded structure made of high-quality steel profiles with through cross-members. Designed for high point loads * Outer frame as UNP profile * Wear plate approx. 8 mm, underride guard nose approx. 700 mm wide Coupling device: * 2-inch kingpin (also suitable for 3.5-inch mounting) Underrun protection: * According to EU regulations, bolted version Side impact protection: * According to EU regulations Landing gear: * 24 t landing legs with single-sided operation (test load approx. 66 t), Jost Modul CH (Heavy Duty) S-foot Axles: * 3 x 9 t air suspension axle units, brand SAF, with disc brakes approx. 430 x 45 mm, ABS, hub-piloted 10-hole wheel bolts with ET 120, total air suspension lift approx. 200 mm (lifting approx. 140 mm, lowering approx. 60 mm), control via rotary slide valve with stop function, with RTR function * Switch for second ride height (+ approx. 50 mm) mounted on the lift/lowering unit bracket * Smartboard/TIM/Infocenter, without TPMS display Lift axle: * First axle liftable, with fully automatic, load-dependent lift control, start assist via push button in driver's cab (15-pin socket PIN12). The cab push button is not included in delivery Brake system: * Two-line compressed air brake system according to EU standard with EBS and RSS, automatic load-dependent adjustment, spring-loaded cylinders as parking brake, anti-swap coupling heads firmly mounted on front cross-member, no connecting line to the tractor unit, brand Wabco Tyres: * 6 units, 385/65 R22.5 160J on rim 11.75 x 22.5 (brand of our choice), ET 120 * Basic tyre pressure monitoring system, connected to the EBS CAN-bus system * Tyre pressure display in the driver’s cab (pre-installed by chassis manufacturer) Mudguards: * According to EU regulations, PVC mudguards (half-shells) over all axles * Mud flaps with anti-spray design Load securing: * 8 pairs of hook plates welded into the outer frame (pulling force approx. 3 t) * 6 pairs of lashing rings in the outer frame, evenly distributed (pulling force approx. 10 t) Stanchion pockets / stanchions: * 5 pairs of stanchion pockets recessed into the outer frame, approx. 90 x 90 x 4 mm * 3 pairs of stanchion pockets recessed into the floor, approx. 90 x 90 x 4 mm * 10 removable stanchions made of galvanized square tube, approx. 80 x 80 x 4 mm, with bottom stop Front wall: * Front wall bolted, approx. 1,200 mm high, sheet metal clad Stanchion magazine: * Magazine for removable stanchions inside the front wall Floor: * Approx. 28 mm hardwood floor recessed in the outer frame, with galvanized Omega steel profiles Hedpfxsyz E T So Ap Iefi Lighting system: * According to EU regulations, 24 Volt with multi-chamber lights, LED side marker lights, white LED position lights front, LED outline marker lights rear, license plate lights * 1 x 15-pin and 2 x 7-pin socket at the front cross-member Equipment: * Warning plate according to ECE 70 * 2 x LED work lights at the lamp carrier (activated by reverse gear) * Bracket for rotating beacon at the rear (including rotating beacon) * 1 folding and extendable rear access ladder (without platform) * 2 stainless steel toolboxes, approx. 450 x 450 x 450 mm, in front of the front wall * Smart-Board with axle load display * 2 LED work lights above the front wall, switchable via switch on the c

Durum: yeni, azami yük ağırlığı: 56.570 kg, toplam ağırlık: 66.500 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, Our complete vehicle stock with immediately and short-term available vehicles can be found on our website. Excerpt from the equipment specification. Complete equipment details available on request. Chassis: * Chassis frame construction made of welded longitudinal beams and inserted cross members Hfjdswx Dctepfx Ap Isi * Underrun nose width approx. 700 mm * Fifth wheel plate at least approx. 8 mm thick, positioned between the main beams * Maximum cross member spacing 400 mm (for longitudinally laid floor) * 3.5 inch kingpin according to SAE standard, replaceable * Outer frame as UNP 200, open to the outside Landing legs: * 24 t telescopic landing gear JOST - MODUL CH (Heavy Duty) S-foot Axles: * 4 x 10 t SAF axles with large drum brake * 22.5 single tires * Axle spacings approx. 1,700/1,810/1,810 mm * Air suspension units, each with 10 t load capacity, lifting and lowering device with 1 rotary valve Knorr/Wabco * Mounting bracket for lifting and lowering device, bolted version Brakes: * Smartboard/TIM/Infocenter on the holder for lifting and lowering, in addition to the lifting and lowering valve, without battery (can only be operated with the towing vehicle) * Holder for lights and brakes at the front of the underrun nose, total height approx. 700 mm * Tire pressure monitoring basic version, connected to the EBS CAN bus system * With dual release valve for brake and spring accumulator * Test nipple for brake cylinder pressure on the front right brake cylinder * 1 coupling head each red and yellow * Lifting and lowering device installed at the rear left in driving direction * EBS brake system by Wabco, EBS diagnostics via CAN bus (EBS connector), no external diagnostic cable provided!! Tyres: * 8 x 445/65 R 22.5 – branded manufacturer of our choice * Hub centering Lubrication: * Grease nipple strips on the bogies and at the front on the steering. No central lubrication Body: * Without body certificate according to DIN EN 12642 XL * 2x LED work lamps on top of the front wall (rear-facing), switch on lifting/lowering control bracket * Robust front wall for platform body * Contour markings side yellow, rear yellow * Front wall approx. 800 mm high, with sheet metal cladding, bolted design Lighting system: * 2x LED work lamps, installed in the lamp plate, switched via reverse gear * 2x LED work lamps, switched via reverse gear, 1x per side near landing gear * 2x LED reversing lights per side, 1 mounted before the 1st axle * Lighting/wiring system by manufacturer of our choice * Number plate lighting * The towing vehicle must provide adequate power for the chosen lighting (esp. reversing lights) * Position lights front, bottom, white, 1 each right and left (LED) * 24 volt lighting system with large multifunction lamp * Side marker lights (LED) flashing * 1x 15-pin and 2x 7-pin connectors at the front via multifunction box * EBS socket * 1 pair of lane departure warning lights (LED) Floor: * Hardwood floor approx. 28 mm, alternately with galvanized omega steel profiles Paint/Coating (no metallic colors): * Chassis painted in RAL color of choice, front wall (steel construction) in RAL color of choice * Axle hubs in chassis color * Axles and landing legs black * Wheels in aluminum/silver similar to RAL 9006 * Wheel nuts untreated * Underrun protection painted in RAL 9010 pure white (aluminum) Accessories: * Lifting device for 1st axle * 9 hook plates welded into the outer frame per side, lashing capacity max. 3,000 daN * 12 RUD SLP lashing points per side w

Durum: yeni, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.550 mm, Donanım: ABS, Our complete vehicle inventory, featuring vehicles available for immediate and short-term delivery, can be found on our website. Excerpt from the equipment specification. Complete equipment details available on request. Chassis: * Welded construction made of high-quality steel profiles with through-type cross-members, designed for high point load * Underride nose, approx. 700 mm wide * Outer frame as UNP profile * Wear plate approx. 8 mm * Fifth wheel height at front approx. 130 mm Towing Equipment * 2" kingpin Underrun Protection * Bolted version, compliant with EC standards Side Protection * EC compliant, made of anodized aluminum profiles Landing Legs * 2 x 12 t landing legs with compensation foot and single-side operation on the right in direction of travel Axles * 3 x 9 t air suspension axle units, disc brakes 22.5" * Total lift approx. 180 mm * Lifting and lowering system via rotary slide valve Brake System * Dual-line compressed air brake system according to EC, with EBS and RSS, automatic load-dependent control * Spring-actuated cylinders as parking brake * Reversal-proof coupling heads permanently mounted on front beam, without connecting line to tractor unit Tyres * 6-off, 385/55 R22.5 160J on 11.75x22.5 ET 120 steel rims, manufacturer of our choice * Tyre pressure monitoring (TPMS) via EBS CAN-bus system Fenders * EC compliant Spare Wheel Carrier Not included Load Securing * 9 pairs of foldable lashing rings, evenly distributed, tensile strength approx. 5.0 t * 9 pairs of foldable lashing rings, evenly distributed, tensile strength approx. 2.0 t * Outer frame with boreholes approx. every 400–600 mm for inserting tension belts Front Wall * Reinforced steel construction, fixed, approx. 1,400 mm high * Interior lined with approx. 9 mm phenolic plywood (approx. 1,250 mm high) Floor * Approx. 28 mm Z-hardwood floor recessed in outer frame with galvanized omega steel profiles Lighting System * EC compliant, 24 V, with multi-chamber lights * LED side marker lights * LED position lights, white, front * LED outline lights, rear * License plate lights * Lane marker LED lights * 1x15- and 2x7-pin socket connectors on front beam Equipment * 2 wheel chocks with holder * ECE 70 warning panels * Bracket for rotating beacon, incl. beacon * 2 rubber dock buffers at the rear * Rear right foldable and extendable access ladder (no platform) * 1 open box made of perforated sheet metal, transverse to the direction of travel, approx. 600 x 450 x 2,430 mm, galvanized, behind axles Paintwork * Front wall: RAL single colour of choice * Chassis: hot-dip galvanized * Outer frame: hot-dip galvanized + RAL single colour of choice * Central stanchions: RAL single colour of choice * Side guard system: aluminium anodized * Underrun protection: white (RAL 9016 traffic white) * Add-on parts: galvanized/KTL black * Rims: silver Conspicuity Marking * Fully yellow Including Special Accessories * First axle liftable, with fully automatic, load-dependent lifting control * 10 pairs of stanchion pockets in the outer frame, evenly distributed * 4 rows of stanchion pockets transverse to the loading area * 20 pieces of stanchions made of galvanized tube 80/50, total length approx. 1,200 mm * Magazine for 20 insertable stanchions on inside of front wall * 5 x 25 side panels and rear panel made of anodized aluminum hollow profiles, foldable and removable * Removable Kinnegrip stanchions Hfodpfxjw U H Sbe Ap Iji * Side panel and stanchion magazine: under-chassis left and right i