Alçak şasi dorse

MÜLLER-MITTELTAL 3- achs Satteltiefl.-Luft-Lenk-hydr. Auffahrram.

Durumu: yeni, azami yük ağırlığı: 38.290 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering system as well as Run-on-Ready (RtR) valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control panel mounted on trailer as an infotool with pressure sensors for axle load display * 15-pin power socket * LED lighting system 12 / 24V * Rear left removable LED beacon ----General Attachments: * Lateral underrun protection * Front landing gears and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel carrier under chassis, right side ----Low Loader Deck: * Fifth-wheel platform with 45° chamfered front corners and toolbox at the front made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm high aluminium drop sides (RAL 9010 pure white) on the sides of the fifth-wheel platform, foldable and removable * 150 mm high removable rear drop board * Rear slope on the fifth-wheel platform to the low bed, approx. 700 mm long * Fifth-wheel platform with 50 mm timber planks, low-bed platform with 60 mm timber planks * Chequer plate over the axles ----Extensions: * 8 x mechanical folding extensions to a total width of 3 m, but not on the rear slope (extension boards included, with storage on the fifth-wheel platform) * Mechanically adjustable warning sign sets front and rear ----Load Securing (Lashing Package): * On the fifth-wheel platform, each 2 x 6.3 t lashing points and 3 x 5 t lashing bars on each side of the outer frame * On the low-bed platform, each side 2 x 13.4 t lashing rings and 4 x 10 t lashing rings, pivoting and retractable, integrated in the outer frame * Each side 2 x 6.4 t lashing eyes and 1 lashing point in the excavator arm recess at the rear * 2 x container locks directly after the step in the low-bed platform ----Excavator Arm Recess: * Continuous excavator arm recess from end of last rigid axle over steering axle to end cross-member, with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanically single-piece, hot-dip galvanized, hydraulic ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way valve block for future retrofit of hydraulic ramp sliding by customer * Outer plank on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump output in truck from over 40 l/min up to 120 l/min) ----Loading Dimensions: * Loading surface of fifth-wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading surface: approx. 8,500 x 2,520 mm * Unladen deck height approx. 910 mm (incl. 860 mm approach slope) ----Fifth-Wheel Height: * Approx. 1,220 mm (suitable for 2-axle and 3-axle tractor units) ----Painting: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in black tone * Vehicle is hot-dip galvanized Hsdpepk D I Ajfx Ad Tjk ----Info: * New vehicle with manufacturer's warranty * Errors and intermediate sale excepted * Sample images may show equipment not included on the offer ----Delivery Time: * Available from week 26/2026

Durumu: kullanılmış, kilometre: 1.400 km, güç: 43 kW (58,46 bg), ilk tescil: 07/2008, yakıt türü: dizel, toplam ağırlık: 4.900 kg, renk: turuncu, vites türü: mekanik, süspansiyon: diğer, çalışma saatleri: 1.400 h, Donanım: her tahrikli, klima, MU/AT yeni, 08.07.2008 1.400 çalışma saati 43 kW 2.746 cm³ Endüstriyel ön yükleyici Dizel Dört çeker Kabin Klima Hidrolik shuttle Çim lastiği Tarla lastiği mümkün Azami toplam ağırlık: 4.900 kg Hjdpfx Adjvidc Ao Tjk BİZİM İÇİN DURUM VE İÇGÜDÜ EN ÖNEMLİSİDİR, FİYAT İKİNCİ SIRADADIR. Diğer sorularınız için lütfen Bay Faller ile belirtilen numaradan iletişime geçin. //ARACINIZI TAKAS EDEBİLİR, SATIN ALABİLİR, TEMİNAT VEREBİLİR YA DA FİNANSMAN SAĞLAYABİLİRİZ! Tüm bilgiler garanti verilmeden sunulmuştur. Diğer tekliflerimiz için lütfen internet sitemizi ziyaret edin. Açıklama ve verilen veriler garanti oluşturmamakta ve bağlayıcı değildir. Satın alma işlemi sırasında galeriyle yapılan satış sözleşmesi bağlayıcıdır. Hatalar ve ara satış hakkı saklıdır!

Durumu: mükemmel (kullanılmış), dingil konfigürasyonu: 2 dingil, ilk tescil: 03/2015, yükleme alanı uzunluğu: 134.450 mm, yükleme alanı genişliği: 2.550 mm, yükleme alanı yüksekliği: 480 mm, süspansiyon: hidrolik, Üretim yılı: 2015, Donanım: ABS, = Diğer seçenekler ve donanımlar = - Merkezi yağlama = Diğer bilgiler = Aks konfigürasyonu Süspansiyon: hidrolik süspansiyon Arka aks 1: Maks. aks yükü: 12.000 kg; Yönlendirilebilir Arka aks 2: Maks. aks yükü: 12.000 kg; Yönlendirilebilir Ağırlıklar Boş ağırlık: 12.660 kg Yük kapasitesi: 34.340 kg Azami toplam ağırlık: 47.000 kg Fonksiyonel Yükleme platformu yüksekliği: 48 cm Çekilebilir üst yapı: Evet Durum Hedpfx Adjvtc Aio Tok Teknik durumu: çok iyi Görsel durumu: çok iyi Finansal bilgiler Fiyat: Talep üzerine Diğer bilgiler Daha fazla bilgi için David F Middelman ile iletişime geçiniz.

Durumu: yeni, azami yük ağırlığı: 67.200 kg, toplam ağırlık: 85.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete range of vehicles, including immediately and short-term available units, on our website. Extract from the specification. Full equipment details available on request. GOOSENECK * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° * For tractor units: 6 x 2, 6 x 4, and 8 x 4 short * Detachable steel front bulkhead, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flush-mount lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized finish * 1 plug-in ALU tailboard, approx. 400 mm high, anodized finish * Approx. 40 mm strong hardwood flooring above the gooseneck, checker plate flooring above the kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, incl. overhead gallows for securing supply lines (Faymonville couplings) * 2 pairs of stake pockets recessed in the gooseneck for plug-in stakes approx. 100 x 50 mm LOADING PLATFORM * Extendable loading platform, length approx. 11,000 mm, rear bevel approx. 500 mm x 10° * Pneumatic locking system with conical locking bolt and reinforced locking positions; supply lines are protected within the extendable beams and automatically adapt to the respective platform length * BPW axles and suspension, 1st axle self-steering, 2nd axle rigid, all other axles hydro-mechanically forced steering * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * Tyres: 235/75 R 17.5 3PMSF twin tires * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous hardwood flooring, approx. 50 mm thick, on the loading platform and interrupted between the axles (providing increased friction coefficient) Hjdpfx Aergzv Njd Tsk * Slotted holes for suspended and repositionable bridging elements: - on the fixed section behind the gooseneck - at the front of the platform * 1 sliding intermediate table, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate covering, slotted holes front and rear for suspended and repositionable bridging elements * 1 pair of flush-mounted lashing rings, lying, in the fixed front section of the loading platform (LC 10,000 daN) * 9 pairs of flush fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle alignment monitoring, without installation in the tractor * 1st axle with automatic lift axle function and starting aid according to EU Directive 2021/535 * Below the gooseneck and at the rear cross member, left and right, a 7-pin socket each with bracket for warning signs * Painted-on sand coating on the outer frame of the platform, the checker plates, and the transition area between the loading platform and...

Durumu: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, 3-axle MULTIMAX PLUS low-loader semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross weight: 49,500 kg or 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Hedpfxjizu Ntj Ad Tjk Kingpin turning radius to rear approx.: 2,100 mm Coupling height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: (value not specified) Loading area width approx.: 2,540 mm Loading height at max load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific legal limits are exceeded. Technical Description Gooseneck: SNT design gooseneck to optimize loading platform length, approx. 3,900 mm length, with rear chamfer approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading area: Loading platform approx. 9,600 mm length with rear chamfer approx. 900 mm x 6°. Section after the gooseneck is hydraulically raisable/lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS Pair of two-section AXS steel ramps, approx. 4,920 mm long and 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Each ramp hydraulically shiftable approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle as per technical datasheet: C470319. Maximum gradient at lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg. Air suspension with lift/lower valve. Axle tools included. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion. Load index 143/141J (144/144F). Braking system: WABCO EBS-E braking system per EU regulations. No cables to the tractor unit. Lighting system: 24V "ASPÖCK-NORDIK full LED" lighting per EU regulations (ASS 3). Metallisation: Complete HRM (High Resistance Metallisation). Full steel structure shot-blasted, then hot-coated with ZINACOR 850 (85% zinc / 15% aluminium). Painting – 6-stage finish: - Complete steel structure shot-blasted after welding - 1 coat zinc-based primer, 1 coat adhesion primer - Top coat with 2 coats 2K acrylic paint, single colour in RAL shade of choice - Cavity sealing with special wax - Rims in silver - Multicolour & special paint available at extra cost Steel structure: High-tensile fine-grain steels Types: S355J2+N/S355MC (yield stress 355 MPa), S690QL/S700MC (yield stress 690 MPa) Welders certified to DIN-EN 287-1, MAG welding per EN ISO 4063, M21 shielding gas as per EN ISO 14175. Front wall: Removable steel front wall, approx. 400 mm high. Supply connection strip for connections to tractor unit, fitted at outer frame profile height. ASPÖCK-UNIBOX at the front supply strip with 24N, 24S & 15-pin sockets. - 24N connection per ISO-1185 - 24S connection per ISO-3731 - 15-pin connection per ISO-12098 If your pin assignment deviates from the ISO standard, please inform us. "Anderson" socket on front supply strip: Rema 78051-00 & Amp. 150 V. Cable for the supply of the electro-hydraulic power pack and/or electric winch (35 mm²,

Durumu: yeni, azami yük ağırlığı: 31.500 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, Donanım: ABS, Wiese 3-axle semi-trailer with lift table and foldable tail section. Ideal for transporting forklifts and/or aerial work platforms. Technical Specifications: - 3 x 10 t axles - Lift axle - Steering axle with Smart Steering (steers forward and reverse) - Outer beam chassis with incline - Gooseneck design rated for 18 t, suitable for 2- and 3-axle tractor units - Hydraulic lift table adjustable in 3 positions - Rear in tailgate version including hydraulic extensions, usable as loading ramps, drive-over ramp or loading area (total length reduced when tailgate is upright) Hodpfx Aovw Hmtjd Tsk - Remote control for ramps and lift table - Front wall - Grated floor - Numerous lashing points - SmartBoard - Central lubrication system - Steel construction, hot-dip galvanized and painted A wide range of options available on request, for example: - Winch - Toolbox on the fifth wheel step - Aluminium rims Further information available upon request.

Durumu: kullanılmış, boş ağırlık: 9.480 kg, azami yük ağırlığı: 31.520 kg, ilk tescil: 03/2020, bir sonraki muayene (TÜV): 04/2024, toplam uzunluk: 11.500 mm, toplam genişlik: 25.500 mm, toplam yükseklik: 38.000 mm, süspansiyon: hava, lastik boyutu: 245/70 R 17.5/10mm, dingil mesafesi: 1.800 mm, ön lastik ölçüsü: 245/70 R 17.5/10mm, işletme ağırlığı: 41.000 kg,

Durumu: kullanılmış, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2017, * SAF akslar * Teker havuzları * Genişliği ayarlanabilir hidrolik yükleme rampaları * Havalı süspansiyon * Genişletilebilir * Boş ağırlık: 11.020 kg Hodpfx Adswta Alj Tok -----Dahili araç numarası: 11010----Hatalar ve ara satış hakkı saklıdır. WhatsApp desteği mevcut! Araçla ilgili sorularınız veya daha fazla bilgi için bize rahatça WhatsApp üzerinden yazabilirsiniz. WhatsApp Almanca, İngilizce -- WhatsApp Almanca, İngilizce, Arapça

Durumu: yeni, boş ağırlık: 10.900 kg, azami yük ağırlığı: 37.100 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 890 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17.5, renk: gri, işletme ağırlığı: 10.900 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear with approx. 1,000 mm x 6° chamfer - Technical fifth wheel load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading Platform: - Loading area, approx. 9,600 mm long, with chamfer at the rear approx. 900 mm x 6° - Loading area behind the gooseneck hydraulically raiseable and lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg - Grating surface and approx. 5 mm steel plate as additional reinforcement on the chamfered section of the loading area Ramps: - One pair of two-piece AXS steel ramps, approx. 4,675 mm long, approx. 900 mm wide - Grating surface - Hydraulically folding ramp tips - Ramps hydraulically adjustable individually approx. 235 mm outwards and approx. 365 mm inwards - Painted sand coating on the outer frame of the ramp as well as on the ramp tip - Flashing lights on the outer side of the ramp tips with switch next to the ramp control - Ramp locking in transport position with quick-release fastener Hedpfsuadk Njx Ad Tok Axles, Suspension and Tyres: - BPW axles and suspension, 1st and 2nd axle fixed, 3rd axle self-steering - 1st axle with starting aid - Operated via the brake pedal of the tractor unit - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 - TPMS tyre pressure monitoring system according to ECE R 141 - TPMS tyre pressure sensors fitted on all wheels including spares Brake System: - WABCO EBS-E braking system according to EU regulations Paintwork: - Trailer painted MB 7350 Novagrau grey Accessories Included: - Plug-in steel front wall, approx. 400 mm high - 3 kW electric hydraulic power pack for controlling hydraulic operations, except hydraulic winches - Guide plate from gooseneck for the fifth wheel plate, approx. 500 mm wide - JOST Module B – static test load = 50,000 kg - Continuous grating surface with 5 mm steel plate underneath as additional reinforcement - Painted sand coating - Cut-outs in the outer frame of the loading platform and lifting bed for attaching hydraulic ramp control valves on the right side of the vehicle - 2" king pin - Central lubrication system with one pump, brand BEKAMAX - On gooseneck, 1 pair of plug-in side ALU folding walls, approx. 400 mm high, anodized - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control - Steel rope approx. 24 m long, rope ø approx. 9.5 mm, incl. rope press roller - WABCO Smart Board system - 4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Durumu: kullanılmış, azami yük ağırlığı: 42.500 kg, toplam ağırlık: 60.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2022, with 12 axles, split, hydraulically suspended, hydromechanical forced steering, with rear bevel and drive-on ramps STZ-L gooseneck - robust steel welded construction - designed loading area: 3,950 x 2,480 mm including bevel - hydromechanical forced steering (dual circuit steering) - turntable-mounted saddle plate with replaceable 2 or 3.5 inch king pin and adjustable steering wedge - fifth wheel load: 24 t - steering radius to rear: 2,600 mm Hsdpew Etd Tofx Ad Tjk Loading Area - recessed outer sections: 4,630 mm, 420 mm deep, providing a loading height of 470 mm or 830 mm with decks installed - extendable by 2,053 mm - including aluminium bridging ramps for creating a level platform - excavator arm trough at rear chassis: 4,900 mm long, 880 mm wide, 480 mm deep - rear chassis length: 4,900 mm incl. 500 mm bevel, loading height 890 mm - one pair of wheel recesses in the lower loading area - hydraulically suspended 3-axle chassis - split Gigant axles with 600 mm lift Rear of vehicle - design: “Beveled” 500 mm - hydraulic rear support Drive-on ramps - two-piece drive-on ramps, length 2,850 + 1,850 mm, width 800 mm - rubber coating with climbing strips Braking System - two-line all-wheel pneumatic brake system with diaphragm brake cylinders - automatic load-dependent brake (ALB) - automatic linkage plates (AGS) - parking brake via spring-loaded cylinders - ABS/ABV brake Special equipment Radio remote control for steering and ramp control Central lubrication system Technical data Gooseneck Loading area (LxW): 3,950 x 2,480 mm Saddle height loaded: 1,300 mm Loading area Loading platform (LxW): 10,030 mm x 2,850 mm, extendable by 2,053 mm recessed outer sections 4,630 mm long plus 2,053 mm extension center beam 980 mm excavator arm trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st axle to 3rd axle: hydromechanically forced steering (dual circuit steering)