Alçak şasi dorse

SCHEUERLE EuroCompact U73+5 Flachbett ausziehbar Pendela.

Koşul: yeni, boş ağırlık: 17.500 kg, azami yük ağırlığı: 43.500 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.750 mm, yükleme alanı yüksekliği: 400 mm, lastik boyutu: 245/70 R 17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and removable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, “SUPER LOW” design, length approx. 7,550 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking - Supply lines routed protected inside the extendable beams and automatically adjust to the respective lowbed length Bodpfx Ahoh Hm The Sewl Rear running gear: - Rear running gear with closed outer frame, chequer plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at rear - 2 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame Axles and tyres: - “PENDLE-AXLE”, all axles forced-steered by hydromechanics - Burst protection valve on axle compensation cylinder with automatic RESET feature - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres / 3PMSF Accessories included: - Prepared for mounting attachable container positions for 1x 20ft or 1x 40ft container on the outer beams - 2'' king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with bracket - At the galvanized front connection strip: yellow-red air couplings - 4 wheel chocks - Remote steering from front and rear by cable remote control with push buttons, including track alignment monitoring for the axles - Hydraulic couplings from gooseneck to lowbed with multi-coupling system instead of screw couplings - Electro-hydraulic unit - White reflector tape according to EU regulations on the sides, extension, and red at the rear - 2 wooden blocks 500x250x200 mm - European reflector plates (red-yellow) at the rear of the trailer - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps for NLGI-2 standard grease - Load pressure gauge to determine axle loads, including load chart - On the gooseneck, plug-in ALU side and rear walls approx. 2,000 x 400 mm - The rear galvanized plug-in posts are removable (body length approx. 2,120 mm) - Separate air connection with air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps to bridge the mountings of the lowbed - Four extendable warning signs approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for the steering in addition to the cable remote, with indicator lights on receiver for track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beam for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Folding extensions, approx. 230 mm per side - Anti-slip sand layer painted on the loading platform - Dipper recess on the rear running gear closed at the front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (Zinc 85% - Alu 15%)

Koşul: yeni, boş ağırlık: 17.250 kg, azami yük ağırlığı: 48.700 kg, toplam ağırlık: 66.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 375 mm, lastik boyutu: 245/70 R 17.5, renk: gri, işletme ağırlığı: 17.250 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized load platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Suitable for tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: - Low bed with external beams, configured as a telescopic vessel bridge in low construction with extension at the front - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Tread plate covering and continuous prismatic excavator recess approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Final coating of axles with 2 layers of single-colour 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps with climbing strips and fixing bolts for bridging the low bed uptake hooks - Ramps can be placed over or between the hooks - Mounting points for steel loading ramps at the rear between the external beams of the gooseneck - One locking position approximately every 1,000 mm on the extension - 1 lashing ring each left and right on the front cross member - Supply line connection strip to the tractor unit, fitted at the height of the outer frame profile - 6 pairs of threaded blocks on the outside of the inner beams of the load platform for mounting screw-on M24 rings - 6 pairs of recessed lashing rings on the outside of the outer beams of the load platform, foldable inwards and outwards - 1 pair of threaded blocks at the front and rear of the outer beams of the load platform for mounting screw-on M24 rings - Insertion strip for loose ALU approach ramps on the rear cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering from front and rear, operable via cable remote control, with single-track control of axles Bwedpfx Ahoh Hm Tzo Ssl - 3 kW electro-hydraulic power pack for operating hydraulic functions, except hydraulic winches - Removable load floor (galvanised), can be inserted in 3 elements between the outer beams, with hardwood covering - Folding extensions, approx. 230 mm per side - Loose widening boards, framed in steel - 4 warning panels approx. 423 x 423 mm - Radio remote control for remote steering operation - 3.5" kingpin - Anti-slip stickers on the left bevel of the gooseneck - Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings - Guiding plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning panels when not in use - 2 pairs of stanchion pockets recessed in the outer frame of the chassis for insertable stanchions approx. 100 x 50 mm - Rear section of the chassis with a detachable plate closing the bucket arm recess at the rear - Trailer colour MB 7350 Novagrau

Koşul: yeni, makine/araç numarası: ...7329, kilometre: 622 km, güç: 309 kW (420,12 bg), yakıt türü: dizel, dingil konfigürasyonu: 8x8, yakıt: dizel, renk: diğer, şoför kabini: gündüz kabini, vites türü: mekanik, vites sayısı: 16, toplam uzunluk: 9.800 mm, toplam genişlik: 2.500 mm, toplam yükseklik: 3.550 mm, Üretim yılı: 1996, The Iveco Trakker 8x8 tanker truck, model 340E42, is a highly mobile vehicle designed for refueling operations with diesel and kerosene. It features a stainless steel tank with a capacity of 18,000 liters, manufactured by IWS DIEHL. This vehicle is in unused condition and comes from former army reserve stock, ensuring reliability and robust performance. Equipped with a 16-speed manual transmission and differential locks on the axles, the tanker offers solid handling and maneuverability across various terrains. It is fitted with single tires, specifically 365/85R20 Michelin XZL, and uses steel suspension for enhanced durability and load-bearing capacity. With only 622 kilometers on the odometer, this tanker is essentially like new. The Iveco Trakker 8x8 is ideal for demanding environments and provides a dependable solution for refueling tasks requiring high capacity and mobility. = Further Information = GVW: 17,600 kg Engine make: IVECO Overall condition: very good Damage: none Bodpfxjutfy Tj Ah Sswl

Koşul: yeni, boş ağırlık: 12.900 kg, azami yük ağırlığı: 34.100 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.850 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 350 mm, süspansiyon: diğer, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 12.900 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,750 mm long - Gooseneck hydraulically height-adjustable and detachable - Technical fifth wheel load: 23,000 kg - Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading Platform: - Low bed with external beams in extendable "SUPER LOW" design, length approx. 6,850 mm - Low bed with fixed hardwood floor approx. 40 mm thick and mechanical locking Rear Chassis: - Rear chassis with closed outer frame, checker plate covering and continuous prismatic excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings foldable outward - 1 pair of lashing rings lying in the trough - 2 pairs of stake pockets for plug-in stakes (100 x 50 mm) in the outer frame Pendulum Axle and Tires: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-insert to secure in lifted position - Final coating of axles with 2 layers of single-color 2K paint, painted in "FAY-Grey-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 245/70 R17.5 - TPMS (Tire Pressure Monitoring System) compliant with ECE R 141 Accessories: - Prepared for fitting of bolted container locking positions for 1x 20ft or 1x 40ft container on the external beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel - On the galvanized connection strip at the front: yellow-red air couplings - 4 wheel chocks - Remote steering front and rear operable via cable remote control with push buttons, including single-track monitoring of the axles - Hydraulic connections from gooseneck to low bed with multi-coupling instead of threaded couplings - Electro-hydraulic unit Bwsdpohlz R Sofx Ah Sjl - White reflector tape on sides, extension and rear, according to EU regulations - European reflector panels (red-yellow) at the rear of the trailer - At the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting of bolt-on RUD rings VLBG-4 - Removable ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized plug-in posts are removable (body length approx. 2,560 mm) - Gooseneck at the upper rear area closed with a removable cover - 5 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading platform - Fold-out extensions, approx. 230 mm per side - 2 pairs of bolt-on RUD rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the low bed’s mounting hooks - Sanded layer painted on the loading platform as an anti-slip coating - Speed stickers 80 km/h on rear and both sides - Rear chassis’ bucket recess at the rear closed with a plug-in plate - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm - Radio remote control for the rear steering, in addition to the cable remote control, with indicator lights on the receiver as single-track monitoring - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determining axle loads - HRM (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces hot-finished in metallization with ZINACOR 850 (Zinc 85% - Alu 15%)

Koşul: yeni, boş ağırlık: 22.700 kg, azami yük ağırlığı: 79.300 kg, toplam ağırlık: 102.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 11.000 mm, yükleme alanı genişliği: 2.850 mm, yükleme alanı yüksekliği: 920 mm, lastik boyutu: 245/70 R 17.5, renk: gri, işletme ağırlığı: 22.700 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading deck length, approximately 3,750 mm long, with rear tapering of about 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6x4 and 8x4 Loading Platform: - Extendable loading platform, length approx. 11,000 mm with rear taper approx. 500 mm x 10° - A recess in the platform and into the taper for accommodating the excavator bucket arm, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking bolt and reinforced locking positions; supply lines are protected in the extendable beams and automatically adapt to the respective platform length Ramps: - One pair of two-part steel ramps, approx. 4,650 mm long and approx. 900 mm wide - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" rubber flooring 25 mm and approx. 5 mm steel flooring as additional reinforcement on the tapered section of the platform Bwsdpfjk Af Svex Ah Ssl - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension and Tyres: - PA-X axle system, all axles forced steered hydro-mechanically - Steering behavior of the first two axles can be optimally adjusted to the platform length both mechanically and hydraulically - Hose rupture valve on the axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pilot pin for securing in raised position - 245/70 R 17.5 3PMSF Accessories Included: - Removable steel front wall, approx. 400 mm high - Supply line connection strip to tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of the gooseneck with mounting holes for screwable lashing rings - The first hole approx. 200 mm from the front, then spaced approx. every 400 mm - 2 pairs of screw-in lashing rings included - Checker plate covering over the gooseneck - 1 pair of removable ALU sideboards approx. 400 mm high, anodized, mounted on the gooseneck - Removable rear ALU wall on the gooseneck, approx. 400 mm high, anodized - 3.5" king pin / 2" king pin fitted - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - 4 wheel chocks - 4 axle load gauges - Mechanical fixed support legs at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical fixed support legs at the front - Continuous steel sheet flooring with painted-in sand layer on the platform for anti-slip protection - 1 intermediate table, approx. 500 mm wide, for the extending section, with elongated holes for suspended and adjustable bridging elements - Painted sand coating on the supporting surfaces of the intermediate table - Mechanical locking for securing the intermediate table in the extended position - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widening units approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing light each left and right at the rear of the vehicle - 3 kW electro-hydraulic power unit - Widening boards, loose, in reinforced steel U-frame - Radio and cable remote control - 4 warning panels, approx. 423 x 423 mm

Koşul: mükemmel (kullanılmış), dingil konfigürasyonu: 3 aks, izin verilen dingil yükü (dingil 1): 12.000 kg, izin verilen dingil yükü (dingil 2): 12.000 kg, izin verilen aks yükü (aks 3): 12.000 kg, yükleme alanı uzunluğu: 17.320 mm, yükleme alanı genişliği: 3.200 mm, yükleme alanı yüksekliği: 400 mm, toplam uzunluk: 17.320 mm, toplam genişlik: 3.200 mm, süspansiyon: hidrolik, lastik boyutu: 245/70 R 17.5 | 143/131L (146/146F), renk: beż, Üretim yılı: 2021, Colour: Yellow Bedpfxovzaanj Ah Sswl Loading capacity: 64,800 kg Main Features Manufacturer: Faymonville Model: GigaMax 1+4 / F-S45-2GXX Chassis Number: YAFTL1009M0027562 Year of Manufacture: 2021 Weights/Loading Capacity King-pin load: 25,000 kg Axle load: 12,000 kg Total axle load: 12,000 kg x 5 = 60,000 kg Gross vehicle weight (GVW): 84,200 kg Unladen weight: 20,200 kg Payload capacity: 64,800 kg Axles Pendle axles Hydraulic suspension All axles with hydraulic steering WABCO braking system with EBS-E Tyres: 245/70 R 17.5 | 143/131L (146/146F) Dimensions Overall length: 17,320 mm Loading platform length: 6,800 mm 2x extension beams: 2,000 mm / 3,000 mm Loading platform width: 2,750 mm / 3,200 mm Loading platform height: 400 mm Ground clearance: 150 mm King-pin height: +/- 1,340 mm Additional information: Gooseneck with integrated 1-axle pendle axle Hatz diesel powerpack Hydraulically operated gooseneck Aluminium side boards on gooseneck 2x extension beams: 2,000 mm / 3,000 mm Excavator trough Lashing rings Stainless steel toolbox Spare wheel + holder Rear under-run protection with lighting King-pin 3.5" Central greasing system with 2 BEKAMAX pumps = Further Information = General Information Year of manufacture: 2021 Axle Configuration Tyre size: 245/70 R 17.5 | 143/131L (146/146F) Suspension: hydraulic suspension Front axle: twin tyres; lift axle; max. axle load: 12,000 kg; steering axles Rear axle 1: twin tyres; lift axle; max. axle load: 12,000 kg; steering axles Rear axle 2: twin tyres; lift axle; max. axle load: 12,000 kg; steering axles Rear axle 3: twin tyres; lift axle; max. axle load: 12,000 kg; steering axles Rear axle 4: twin tyres; lift axle; max. axle load: 12,000 kg; steering axles Weights Unladen weight: 20,200 kg Payload: 64,800 kg Gross vehicle weight: 85,000 kg Functional Platform height: 40 cm Extendable structure: Yes Condition Technical condition: very good Visual condition: very good Financial Information Price: On request Additional information Please contact Stefan Schaapveld for further information.

Koşul: iyi (kullanılmış), Fonksiyonellik: tamamen fonksiyonel, kilometre: 198.108 km, güç: 270 kW (367,10 bg), vites türü: otomatik, yakıt türü: dizel, renk: sarı, toplam ağırlık: 48.000 kg, lastik boyutu: 445/95 R25, ilk tescil: 03/2008, süspansiyon: hidrolik, Üretim yılı: 2008, çalışma saatleri: 13.613 h, makine/araç numarası: W094845008EL05362, Donanım: ABS, UVV güvenlik kontrolü, araç içi bilgisayar, diferansiyel kilidi, kabin, park ısıtıcısı, retarder, Konum: 73230 Kirchheim unter Teck Liebherr LTM 1070-4.1 Fabrika No: 059 524 Kaldırma kapasitesi: 70 t / 2,5 m / %75 Üretim yılı: 2008 - Teleskopik bom: 11–50 m - Vinç sayısı: 1 - Karşıağırlık: 14,5 t - Kanca bloğu: 3 makaralı, 38,3 t (DH) - Alt şasi motoru: Liebherr Dizel D 936 L A7 – Çalışma saati: 21.043 h / 270 kW / 367 PS (EURO III) - Alt şasi çalışma saati: 7.430 h - Üst şasi (vinç çalışma saati): 13.613 h - Şanzıman: ZF AS-Tronic otomatik şanzıman - Tahrik/direksiyon: 8 x 6 x 8 - Ek fren: Telma retarder - Lastikler: 445/95 R25 (16.00 R25) Bridgestone - Kilometre: 198.108 km Bodpfx Ahsx H Shts Sewl Diğer Özellikler - Sürücü ve vinç kabininde kalorifer - Destek kuvveti göstergesi - Çalışma alanı sınırlama - Dönüş parçasında xenon çalışma farı İyi durumda, hemen kullanıma hazır – ek bilgiler talep üzerine – kısa sürede teslim edilebilir.

Koşul: ikinci el, kilometre: 107.755 km, güç: 260 kW (353,50 bg), vites türü: otomatik, yakıt türü: dizel, renk: sarı, dingil konfigürasyonu: 6x6, ilk tescil: 08/2009, emisyon sınıfı: Euro 3, Üretim yılı: 2009, Donanım: ABS, araç içi bilgisayar, diferansiyel kilidi, klima, tır çekici bağlantısı, vinç, çekiş kontrolü, - Alet kutusu - EBS - Elektrikle ayarlanabilen kapı aynaları - Elektrikle çalışan camlar - Hidrolik direksiyon - Isıtma Bwedpfsxt T Tujx Ah Sel - Isıtmalı koltuk - Merkezi yağlama - Radyo - Sis lambaları

Koşul: yeni, azami yük ağırlığı: 65.400 kg, toplam ağırlık: 93.400 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Pos. 1. Type STZ-VP 6 (245) (2+4) with pendulum axles The specified technical data are only valid when using a 4-axle tractor unit with the following data: Dimension a: 5,400 mm Bsdpfxjwg N N Io Ah Sjwl Fifth wheel height (loaded): 1,300 mm Weights - Speed 80 km/h Fifth wheel load: 22,000 kg Axle load: 6 x 12,000 kg Gross vehicle weight rating: 94,000 kg Curb weight: approx. 29,600 kg Payload: approx. 64,400 kg (depending on load chart / easyLOAD calculation) Dimensions Dimension b: 18,765 mm Total combination length: 24,165 mm Vehicle width: Gooseneck length x width: 3,700 mm x 2,480 mm Fifth wheel height (loaded): 1,300 mm Steering radius front/rear: 1,370 mm / 2,735 mm King pin: 3.5'' 2-axle front running gear Wheelbase: 1,510 mm Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S Steering axle arrangement: counter-steered 14,400 mm flatbed (external beams), single telescoping with disconnect point Length x width: 7,000 mm x 2,750 mm Telescopic extension by/max.: 3,400 mm / 10,400 mm Build height: 300 mm Plus 4,000 mm extension beam incl. Loading height loaded: approx. 450 mm 4-axle rear running gear Wheelbase: 3 x 1,510 mm Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S Steering axle arrangement: forced steering

Koşul: ikinci el, dingil konfigürasyonu: 3 aks, ilk tescil: 10/2006, toplam genişlik: 2.850 mm, süspansiyon: diğer, lastik boyutu: 285/70R19.5, renk: siyah, Üretim yılı: 2006, Donanım: ABS, = Additional Options and Accessories = - Central lubrication = Remarks = Bsdoxbng Espfx Ah Sowl Faymonville Jeep Dolly D3 Year: 10-2006 • 1 x lift axle • 1 x friction-steered axle / trailing steering • Air suspension • Max. technical weight: 56,000 kg Faymonville STBZ-5VA Year: 10-2006 • Pendle axle • Removable gooseneck • Movable table • Extendable bed: 400 cm • Load bed: 650 + 400 cm • 50,000 kg gooseneck load • Max. technical weight: 119,680 kg = Further Information = Axle configuration Tire size: 285/70R19.5 Brakes: Drum brakes Front axle 1: Twin tires; Tire tread left inside: 15%; Tire tread left outside: 60%; Tire tread right inside: 60%; Tire tread right outside: 60%; Suspension: Air suspension Front axle 2: Twin tires; Tire tread left inside: 30%; Tire tread left outside: 30%; Tire tread right inside: 40%; Tire tread right outside: 60%; Suspension: Air suspension Front axle 3: Twin tires; Steering; Tire tread left inside: 30%; Tire tread left outside: 70%; Tire tread right inside: 60%; Tire tread right outside: 70%; Suspension: Air suspension Rear axle 1: Twin tires; Steering; Tire tread left inside: 30%; Tire tread left outside: 60%; Tire tread right inside: 40%; Tire tread right outside: 70%; Suspension: Hydraulic suspension Rear axle 2: Twin tires; Steering; Tire tread left inside: 50%; Tire tread left outside: 50%; Tire tread right inside: 30%; Tire tread right outside: 75%; Suspension: Hydraulic suspension Rear axle 3: Twin tires; Steering; Tire tread left inside: 60%; Tire tread left outside: 60%; Tire tread right inside: 60%; Tire tread right outside: 60%; Suspension: Hydraulic suspension Rear axle 4: Twin tires; Steering; Tire tread left inside: 60%; Tire tread left outside: 60%; Tire tread right inside: 40%; Tire tread right outside: 50%; Suspension: Hydraulic suspension Rear axle 5: Twin tires; Steering; Tire tread left inside: 70%; Tire tread left outside: 70%; Tire tread right inside: 20%; Tire tread right outside: 70%; Suspension: Hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 83,080 kg Gross vehicle weight: 119,680 kg Financial Information Price: On request Identification Type number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company Information = ALL PRICES ARE NET FOR EXPORT, Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT), We speak Russian. We strive to provide correct information, but no rights can be derived from the listed texts.