Kullanılmış Müller-Mitteltal Etü Fragmanlar satın al (272)

Koşul: yeni, azami yük ağırlığı: 6.870 kg, toplam ağırlık: 9.900 kg, dingil konfigürasyonu: 1 dingil, Üretim yılı: 2026, * KWH 9.9 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support winch at the front * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Drawbar with 40 mm bolted towing eye (height-adjustable mm) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made of torsionally stiff square tubing and cross-members * Enclosed steel mudguards with splash protection * Enclosed side underride guard, can be used as an advertising space * Plastic toolbox with floor liner (laying installation) approx. 500 x 350 x 400 mm * Swiveling cable drum construction, clear width between drum arms 1,700 mm, with tension latch for drum securing at the carrying arm ends as well as a central claw lock for connecting the cable drum frame to the chassis * Motor hydraulic drum drive with oil motor * Valves and movable, rubber-coated drive rollers * Hydraulic speed regulator and brake for the drum drive * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 1 pair of polyamide centering cones, stepped design * Hydraulic power unit with Loncin petrol engine, includes manual and electric starter * Fuel tank and manual starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * 2,690 kg unladen weight * Vehicle is hot-dip galvanized * New vehicle with full manufacturer's warranty Redpfou I Iqrox Aatocb * Subject to errors and prior sale * Immediately available from Egestorf

Koşul: yeni, azami yük ağırlığı: 6.870 kg, toplam ağırlık: 9.900 kg, dingil konfigürasyonu: 1 dingil, Üretim yılı: 2026, * KWH 9.9 ML: * RDÜ Tire Pressure Monitoring System * EBS Braking System * Drum Brakes * BPW Axle Rsdpfx Aeu I Iq Ejatocb * Parabolic Springs * Front Support Wind Jack * Rear Square Tube Supports with Spring Assist and Base Plate, Safety Lock Pins for Adjustable Support Heights * Drawbar with 40 mm Screw-Type Towing Eye (height-adjustable mm) * 15-pin Electrical Connector * LED Lighting * Flashing LED Side Marker Lights * Chassis Made of Torsion-Resistant Square Tubes and Cross Members * Closed Steel Mudguards with Splash Protection * Closed Side Underrun Protection, Usable as Advertising Space * Plastic Toolbox with Bottom Insert (installed lying down) approx. 500 x 350 x 400 mm * Swiveling Cable Drum Superstructure, width between drum arms 1,700 mm – with tension lock for drum securing at support arm ends as well as a central claw lock for securing the cable drum superstructure to the chassis * Motor-Hydraulic Drum Drive with Oil Motor * Valves and Adjustable Rubber-Covered Drive Rollers * Hydraulic Speed Controller and Brake for Drum Drive * Steel Drum Shaft with 76 mm Diameter as well as Centering and Rotatable Ends * 1 Pair of Stepped Polyamide Centering Cones * Hydraulic Pump Unit with Diesel Engine * Fuel Tank and Hand Starter * 6.5 HP with Gear Pump (150 bar) * Hot-Dip Galvanized Color * New Vehicle with Full Manufacturer Warranty * Subject to errors and prior sale * Immediately available ex Egestorf * Sample images

Koşul: yeni, azami yük ağırlığı: 6.870 kg, toplam ağırlık: 9.900 kg, dingil konfigürasyonu: 1 dingil, Üretim yılı: 2026, * KWH 9.9 ML: * RDÜ Tire Pressure Monitoring System * EBS Brake System * Drum Brakes * BPW Axle * Parabolic Springs * Front Support Winch * Spring-assisted square tube supports at the rear with baseplate and safety locking pins for different support heights * Drawbar with 40 mm bolt-on towing eye (height adjustable, mm) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubular steel and cross members * Enclosed steel mudguards with splash protection * Enclosed side underrun protection, suitable as advertising space * Plastic toolbox with floor insert (installed lying down), approx. 500 x 350 x 400 mm * Swiveling cable drum structure, light width between drum arms 1,700 mm, with clamp lock for securing the drum at the ends of the support arms, as well as central claw lock for fixing the cable drum structure to the chassis Rjdpfou I Iqfjx Aatscb * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated friction rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotating ends * 1 pair of stepwise graduated centering cones made of polyamide * Hydraulic pump unit with Loncin petrol engine, including hand and electric starter * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * Unladen weight 2,690 kg * Vehicle is hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Available immediately ex Egestorf * Sample images

Koşul: yeni, azami yük ağırlığı: 6.900 kg, toplam ağırlık: 9.900 kg, dingil konfigürasyonu: 1 dingil, Üretim yılı: 2026, * KWH 9.9 ML: * TPMS (Tire Pressure Monitoring System) * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Support windlass at the front * Spring-assisted square tube supports at the rear with base plate and safety locking pins for various support heights * Drawbar with 40 mm screwed towing eye (height adjustable mm) * 15-pin electrical connector Rcjdpoxyniwofx Aatsb * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and crossbeams * Closed fenders made of sheet steel with splash guards * Closed side underrun protection can be used as an advertising area * Plastic toolbox with base inlay (horizontal installation) approx. 500 x 350 x 400 mm * Swiveling cable drum frame, clear width between the drum arms 1,700 mm with tension latch for drum securing at the support arm ends and a central claw lock securing the drum frame to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotating ends * 1 pair of stepwise offset centering cones made of polyamide * Hydraulic lines supply and return * Chassis and hydraulic preparation for retrofit of a separate engine * 315/80 R 22.5 tires * Unladen weight: 2,690 kg * Vehicle is hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and intermediate sale excepted * Immediately available ex Egestorf

Koşul: iyi (kullanılmış), dingil konfigürasyonu: 3 dingil, izin verilen dingil yükü (dingil 1): 10.000 kg, izin verilen dingil yükü (dingil 2): 10.000 kg, izin verilen aks yükü (aks 3): 10.000 kg, ilk tescil: 11/2015, toplam uzunluk: 14.000 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.050 mm, süspansiyon: hava, lastik boyutu: 235/75 17.5, dingil mesafesi: 1.300 mm, Üretim yılı: 2015, Donanım: ABS, = Further Options and Accessories = - EBS - Rear air suspension = Remarks = - Müller Mitteltal 3-axle low-loader - 3 × 10,000 kg axles - Fifth-wheel load: 11,000 kg - Load platform dimensions: length 930 cm × width 252 cm - Loading height: 98 cm - Covered neck dimensions: length 500 cm × width 264 cm - Neck loading height: 144 cm - Sliding tarp left and right - Dimensions of the hydraulic loading ramp: - Section 1: 270 × 235 cm - Section 2: 180 × 235 cm - Lashing points - 2 storage boxes Well-maintained and robust low-loader, ideally suited for transporting, among other things, machinery, forklifts, and access platforms! = Further Information = Axle configuration Tyre size: 235/75 17.5 Suspension: Air suspension Rjdpfxsy I Axxj Aatecb Rear axle 1: twin tyres; max. axle load: 10,000 kg; tyre tread left inner: 50%; tyre tread left outer: 50%; tyre tread right inner: 50%; tyre tread right outer: 50% Rear axle 2: twin tyres; max. axle load: 10,000 kg; tyre tread left inner: 50%; tyre tread left outer: 50%; tyre tread right inner: 50%; tyre tread right outer: 50% Rear axle 3: twin tyres; max. axle load: 10,000 kg; steered; tyre tread left inner: 30%; tyre tread left outer: 30%; tyre tread right inner: 30%; tyre tread right outer: 30% Weights Curb weight: 10,700 kg Payload: 25,300 kg Gross vehicle weight: 36,000 kg Condition Technical condition: good Cosmetic condition: good Product Safety Manufacturer: Clean Mat Trucks B.V. Wageningsestraat 17 6673DB ANDELST, NL

Koşul: ikinci el, boş ağırlık: 3.110 kg, azami yük ağırlığı: 9.490 kg, toplam ağırlık: 12.600 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 05/2016, bir sonraki muayene (TÜV): 02/2025, yükleme alanı uzunluğu: 4.550 mm, yükleme alanı genişliği: 2.380 mm, yükleme alanı yüksekliği: 600 mm, süspansiyon: çelik, lastik boyutu: 285/70R19.5, renk: mavi, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Vehicle location: Bovenden, steel body, 2 axles, turntable steering, leaf suspension, ABS (anti-lock braking system), lashing eyes, tool box, swing tailgates Body: 2-axle 3-way tipper trailer, Gigant axles, drum brakes, hot-dip galvanized frame! Loading height approx. 1290 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors! Rcodpfxswth Iij Aatjb

Koşul: ikinci el, dingil konfigürasyonu: 3 dingil, süspansiyon: parabolik yaprak (yay), lastik boyutu: 235-75R17.5, Üretim yılı: 2010, 3 dingilli alçak şasi römork, arkadan yüklenebilir. Azami toplam ağırlık 30.000 kg, taşıma kapasitesi 22.700 kg. Yükleme alanı 8.900 mm (7.000 + 1.900) x 2.550 mm, aşırı genişlik için ikaz paketi, 12 yük bağlama halkası ile 8 dikme cebi, aynı zamanda bağlama imkanı, 6 adet alet kutusu. İki parçalı hidrolik rampalar yaklaşık 2.100+2.000 x 800 mm ve kauçuk kaplamalı, hidrolik arka destek. BPW akslar, EBS, dengeleme ünitesine sahip parabolik süspansiyon, lastik ölçüsü 235-75 R 17.5. Kavisli çekme kolu, döner çekme gözü 40+50 mm. 2 hatlı hava (Duomatik), 2 hatlı hidrolik, 24 volt. Boşken yükseklik yaklaşık 910 mm. Turuncu boyalı. Muayenesi 03-2027'ye kadar geçerli. Rsdpfx Aey Evvloatscb = Ek Bilgiler = Lastik ölçüsü: 235-75R17.5 Süspansiyon: Parabolik süspansiyon Boş ağırlık: 7.300 kg Yük kapasitesi: 22.700 kg Azami toplam ağırlık: 30.000 kg Üretim ülkesi: DE Daha fazla bilgi için Jan-Marc Schwickert ile iletişime geçin.

Koşul: ikinci el, azami yük ağırlığı: 4.960 kg, toplam ağırlık: 10.500 kg, ilk tescil: 04/1993, bir sonraki muayene (TÜV): 01/2026, yükleme alanı uzunluğu: 6.260 mm, yükleme alanı genişliği: 2.430 mm, yükleme alanı yüksekliği: 2.430 mm, yükleme alanı hacmi: 37 m³, Donanım: ABS, hidrolik arka platform, 2-axle tandem refrigerated trailer, 7 m, with 1-ton tail lift * THERMOKING LND-II MAX (diesel engine) and standby cooling 380 V ELECTRIC * Vehicle no. for customer inquiries: 4593 * Tail lift * Air suspension * EBS (Electronic Braking System) * Anti-lock Braking System (ABS) Rcjdpoykxflefx Aateb No liability for printing or typing errors Sale exclusively to business customers Subject to prior sale and errors. Changes, prior sale and errors expressly reserved. The description serves only as vehicle identification and does not constitute a warranty in the legal sense of a purchase. The description in the purchase contract is binding. * TOP SERVICE + QUALITY * We can provide a LEASING-FINANCING-HIRE PURCHASE offer * Warranty insurance available on request from the insurer * TÜV / UVV tail lift inspection / Tachograph testing and fitting of OBU unit by our local partners * 30-day export license plates available    All export documents possible, but must be requested separately individually * TOLL booking for Toll-Collect can be arranged in-house * Free transfer from Stuttgart Airport or Metzingen train station (Württ) * TRAIN STATION FOR ARRIVAL: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP Number * * ---- Visit us on our website at * over 200 vehicles in stock at all times

Koşul: yeni, azami yük ağırlığı: 20.500 kg, toplam ağırlık: 27.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2026, * ETÜ-TR 27.0 flatbed: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system with RTR function * 1st axle liftable * Last axle as self-steering trailing axle with electro-pneumatic steering lock via PIN reverse gear (lock of trailing axle from the tractor for maneuvering purposes – without any truck-side installation – assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for use in public road traffic) * SmartBoard control box as an infotool with pressure sensors for total axle load display * Tire pressure monitoring with in-cab display via EBS signal, without need for truck-side installation * Fixed central drawbar with 50 mm flange towing eye (loaded 900 mm, adjustable height at head plate) * Mechanical landing leg at the front, mechanical swing-down support legs at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center posts) up to the drive-on slope * Folding rear stanchions * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Toolboxes made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm, mounted right side * 15-pin power connector * LED rear lights * LED revolving beacon (removable), including bracket and installation * 2 x LED reversing lights at the rear of the vehicle (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir timber flooring * 400 mm steel front wall, plug-in * Perforated outer frame, approx. 45 degrees bent, with fixture for fitting 3 t lashing brackets * In each corner, 1 x 10 t lashing ring, plus 2 x 10 t and 3 x 6.3 t lashing rings on each side * In front and end crossmembers, various holes for 1.2 t lashing options * Hydraulic, one-piece ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-section hydraulic control block for possible later retrofit of hydraulic ramp displacement * Chassis, drawbar, front wall, rear mechanical supports, and ramps hot-dip galvanized * Axles, air tanks, flange towing eye, and front landing leg painted in black * Hydraulic flow divider in trailer (for hydraulic pump performance in truck from over 40 l/min to 120 l/min) * New vehicle with manufacturer warranty * Subject to errors and prior sale Rjdpfxer Dpzxs Aatecb * Immediately available ex Egestorf

Koşul: yeni, azami yük ağırlığı: 37.560 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, * TS 3 RM ML 30.0: ----Braking System: * Wabco EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11-ton BPW axles * Traction aid for shunting purposes, activated on the first axle via EBS (no truck-side installation required) * The last axle as a self-steering trailing axle with electro-pneumatic steering lock * Locking of the trailing axle for shunting purposes, controlled from the driver's cab via EBS (no truck-side installation required) ----Suspension: * Air suspension with lift and lower function as well as Ride height control valve ----Electrical / Lighting: * Smart-Board mounted as an info tool on the trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * Removable LED rotating beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for extended length lighting * Side marker lights with indicator function * Tire pressure monitoring system with display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: Rcedpfx Asykx Nkjatjb * Side underrun protection * Landing gears at the front and swiveling supports at the rear of the chassis * Straight sheet steel mudguards * Spare wheel holder in front of the bulkhead cross member (without spare wheel) * Mechanically adjustable warning sign packages at the front and rear * Swivel arm as carrier for connection lines from truck to trailer ----Low Loader Platform: * 2nd kingpin position * Fifth wheel platform with 45° chamfered front corners and a front toolbox made of galvanized, powder-coated sheet steel, W = 2,480 mm x H = 500 mm x L = 665 mm with hinged lid * 400 mm high aluminium drop and removable side walls (in RAL color of choice) on the fifth wheel platform * Rear wall —150 mm— plugged in high * Rear slope on the fifth wheel platform to the low-bed, approx. 700 mm long with checker plate covering and a perforated strip at the end for attaching aluminium drive-on ramps * Fifth wheel platform with 50 mm clamped wooden floorboards, low bed platform with 60 mm clamped wooden floorboards * Checker plate over the axles * 9 mechanical folding wideners to 3 m overall width (excluding rear slope); widening planks available with closed transverse storage compartment underneath the load platform * Preparation for 3 insertion shafts under the fifth wheel platform to store either aluminium drive-on ramps or wooden planks for covering wheel recesses * Preparation for container locks on the gooseneck ----Load Securing (LaSi Package): Fifth Wheel Platform: * Perforated external frame, 45° bent, with hole pattern for lashing devices (2 t lashing capacity per point at a minimum distance of 480 mm) * 3 x 13.4 ton lashing rings recessed to the side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the step, 1 x above the middle axle next to the longitudinal beam) Low Loader Platform: * 3 x 13.4 ton lashing rings on each side of the external frame (1 x at the start of the fifth wheel step, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 ton lashing rings on each side (1 x between the front wheel recess and first axle, 1 x between 2nd and 3rd axle) * 3 x 5 ton lashing rings screwed to each side of the external frames of the wheel recesses (2 at the front, 1 at the rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from end of last

Koşul: yeni, azami yük ağırlığı: 37.560 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Maneuvering aid for shunting purposes on the first axle, activated via EBS (no truck-side installation required) * Rear axle as self-steering axle with electro-pneumatic steering lock * Steering lock for the trailing axle, operated from the cab for shunting purposes via EBS (no truck-side installation required) ----Suspension: * Air suspension with lift and lower function and RTR valve ----Electrics / Lighting: * Smart-Board installed on the trailer as an info tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for length extension lighting * Side marker lamps with indicator function * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Side underrun protection * Support winds at the front and swiveling supports at the rear on the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall crossmember (without spare wheel) * Mechanically adjustable warning sign packages front and rear * Swivel arm as a carrier for connection cables from the truck to the semi-trailer ----Lowbed Deck: * 2nd kingpin position * Fifth wheel platform with 45° chamfered front corners and tool box at the front made of galvanized, powder-coated steel B = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm high drop-side aluminium boards on the sides of the fifth wheel platform (in RAL color of choice), foldable and removable * Rear wall insertable, 150 mm high * Rear slope on the fifth wheel platform, approx. 700 mm long with chequer plate surface and at the end a perforated bar for hooking in aluminium loading ramps * Fifth wheel platform with 50 mm clamped wooden planks and lowbed platform with 60 mm clamped wooden planks * Tear plate over the axles * 9 x mechanical fold-out extensions to 3 m total width, except on the rear slope (extension boards available with closed storage compartment crosswise under the loading area) * Preparation for 3 mounting shafts under the fifth wheel platform to store either aluminium loading ramps or wooden planks for wheel well covers * Preparation for container locks on the swan neck ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame, 45° angled with hole pattern for lashing points (2 t lashing force per point at a minimum spacing of 480 mm) * 3 x 13.4 t lashing rings recessed into the floor on each side (1 x on the fifth wheel platform, 1 x on the longitudinal beams after necking, and 1 x above the center axle next to the longitudinal beam) Lowbed platform: * 3 x 13.4 t lashing rings on each side of the outer frame (1 x start of the fifth wheel platform neck, 1 x start of the ramp slope, 1 x end of the ramp slope) * 2 x 10 t lashing rings on each side (1 x between the front wheel well and 1st axle, and 1 x between 2nd and 3rd axles) * 3 x 5 t lashing rings on each side, bolted to the outer frame of the wheel well (2 on the front wheel well, 1 on the rear wheel well) Rodpfx Aaeykx Nqstecb ----Excavator boom support: * Extended excavator boom support from the end of the last rigid axle, over the steering axle, up to the end crossmember, continuous with internal reinforceme

Koşul: yeni, azami yük ağırlığı: 20.500 kg, toplam ağırlık: 27.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, Üretim yılı: 2026, * ETÜ-TR 27.0 Flatbed: * EBS (electronic braking system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lowering function featuring RTR function * 1st axle liftable * Last axle as a trailing steering axle with electro-pneumatic steering lock via reverse gear pin (trailing axle lock for shunting purposes from the towing vehicle side - without any vehicle-side installation - assigned to PIN 10 in the 15-pin connector, only for shunting, not for use on public roads) * SmartBoard control unit as an info tool with pressure sensors for total axle load display * Tire pressure monitoring with in-cab display possible via EBS signal without any vehicle-side installation * Fixed central drawbar with 50 mm flanged towing eye (loaded height 900 mm, adjustable headplate height) * Mechanical landing gear in front, mechanical swiveling supports at the rear of the chassis * Mechanically adjustable warning signage package front and rear * Toolboxes made of galvanized sheet steel – black powder coated – approx. 650 x 300 x 600 mm, located right side * Hydraulic flow divider * Continuous side walls (without central stanchion) up to the drive-on slope * Rear stanchions foldable * Steel rear wall inserted in front of the rear stanchions * 15-pin electrical connector * LED tail lights * Removable LED beacon including holder and installation * 2 x LED reverse lights at the rear of the vehicle (switched via reverse gear) * Flashing LED side marker lights Redpfxor Dpz As Aatocb * 60 mm larch/Douglas fir wooden floor * 400 mm steel front wall, slotted in * Perforated external frame approx. 45° bent, equipped for the installation of 3 t lashing brackets * One 10 t lashing ring in each corner; additionally, two 10 t and three 6.3 t lashing rings on each side * Various drill holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * Four-way hydraulic valve block for possible retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, mechanical rear support legs, loading ramps, tailgate hot-dip galvanized * Axles, air tanks, flanged towing eye, and front landing gear painted in a black tone * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck of over 40 liters up to 120 liters/min.) * New vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available from Egestorf

Koşul: ikinci el, boş ağırlık: 2.700 kg, azami yük ağırlığı: 7.300 kg, toplam ağırlık: 10.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 06/2006, yükleme alanı uzunluğu: 4.500 mm, yükleme alanı genişliği: 2.200 mm, yükleme alanı yüksekliği: 1.000 mm, süspansiyon: çelik, lastik boyutu: 245/70R19.5, renk: turuncu, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Vehicle location: Bovenden, steel body, leaf suspension, 2 axles, BPW axles, tandem, lashing rings, underrun protection, front support, swing tailgates. Body: 3-way tipper trailer, steel drop sides, swinging and folding, 2x BPW axles, drum brakes! Loading height approx. 1040 mm. Rsdpfsytxx Rex Aatjcb Drop sides foldable at both top and bottom! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale and errors excepted!

Koşul: ikinci el, dingil konfigürasyonu: 3 aks, süspansiyon: parabolik yaprak (yay), lastik boyutu: 235-75R17.5, Üretim yılı: 2008, 4 dingilli alçak şasi römork, üzerinden geçilebilir. Azami toplam ağırlık 40.000 kg, taşıma kapasitesi 31.820 kg. Yükleme yüzeyi yaklaşık 9.800 mm (2.400+7.400 mm) x 2.550 mm, katlanabilir genişletmelerle 3.000 mm'ye kadar, aşırı genişlik uyarı paketi, döner tepe lambası, kepçe kolu desteği, yükseklik yaklaşık 900 mm. 12 bağlama halkası, dış şasede 12 bağlama köprüsü. Hidrolik rampalar yaklaşık 3.000 x 650 mm. SAF akslar, EBS, dengeleyicili parabolik süspansiyon, lastik ölçüsü 235-75R17.5. Takım sandığı. Arka hidrolik ayaklar. Çeki oku 50 mm. 2 hat hidrolik, 2 hat hava (duomatik), 24 volt. Sarı boya. Mevcut durumda satılık. = Daha fazla bilgi = Lastik ölçüsü: 235-75R17.5 Rcsdpfx Aeuuxg Noatob Süspansiyon: Parabolik süspansiyon Boş ağırlık: 8.180 kg Yük kapasitesi: 31.820 kg Azami toplam ağırlık: 40.000 kg Üretim ülkesi: DE Daha fazla bilgi için Jan-Marc Schwickert ile iletişime geçin.

Koşul: ikinci el, azami yük ağırlığı: 13.860 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2022, yükleme alanı uzunluğu: 6.770 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 600 mm, yükleme alanı hacmi: 10 m³, Donanım: ABS, ? galvanizli şasi ? alçaktan bağlı ? 50 mm çekme halkası ? konteyner kilidi ? her iki tarafta 12 bağlama halkası ? geri görüş kamerası ? kampana fren ? duomatic bağlantı ? ABS ? havalı süspansiyon ? alet kutusu ? EBS ? destek ayakları ? ikiz lastik Rjdpfx Aaexb Ig Sotecb ? BPW akslar Tüm bilgiler taahhütsüzdür / ara satış hakkı saklıdır.

Koşul: ikinci el, azami yük ağırlığı: 13.860 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2022, yükleme alanı uzunluğu: 6.770 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 600 mm, yükleme alanı hacmi: 10 m³, Donanım: ABS, ? Galvanizli şasi ? Alçak bağlantı ? 50 mm çeki halkası ? Konteyner kilitleme Rcedpfx Aajxb Iglsteb ? Her iki tarafta 12 sabitleme halkası ? Geri görüş kamerası ? Kampana fren ? Duomatic bağlantı ? ABS ? Havalı süspansiyon ? Takım sandığı ? EBS ? Destek ayakları ? İkiz tekerlekler ? BPW akslar Tüm bilgiler taahhütsüzdür / Ara satışa tabidir.

Koşul: mükemmel (kullanılmış), dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 85.000 mm, yükleme alanı genişliği: 30.000 mm, yükleme alanı yüksekliği: 30.000 mm, Üretim yılı: 2016, T3 Profil 30, 0: Drum brakes, 3 x 10 t axles, side underrun protection, swing-out supports at the rear of the chassis frame, mechanically adjustable warning sign packages at the front and rear, folding lid on the toolbox in the bogie platform, 4 lashing eyes per side, 6 pairs of mechanical folding outriggers for a total width of 3 m, extension planks stored in the middle of the loading area, hydraulically operated, two-part loading ramps, laterally adjustable, loading area above the slewing ring: approx. 2,000 x 2,520 mm, loading height approx. 1,070 mm, rear loading area: approx. 6,500 x 2,520 / 3,000 mm, loading height approx. 910 mm (including 860 mm approach slope), technically permitted gross weight of 30,000 kg, vehicle is hot-dip galvanized and in excellent, near-new condition. = Further information = Weights Rodoyz Ix Repfx Aatecb Payload: 24,000 kg gross vehicle weight: 6,000 kg Maintenance, history, and condition Number of owners: 1 Technical condition: Very good Visual condition: Very good Further details Front tire condition: 90% Rear tire condition: 90% Front tires: 235/75 R 17.5 Rear tires: 235/75 R 17.5 Country of manufacture: DE Further information Please contact Bernd Strack for further details.

Koşul: yeni, azami yük ağırlığı: 6.810 kg, toplam ağırlık: 9.600 kg, dingil konfigürasyonu: 1 dingil, yükleme alanı uzunluğu: 4.030 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 700 mm, Üretim yılı: 2026, * EK 9.6 ----Braking system: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * SAF axle ----Suspension: * Parabolic springs Rcodpfxew Ndr Uj Aatob ----Drawbar / Flange Eye: * Drawbar as central axle drawbar with 40 mm bolt-on drawbar eye * Infinitely adjustable drawbar height via spindle lifting element instead of rigid drawbar ----Coupling height: * Standard coupling height approx. 900 mm (+/- 150 mm) ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * 15-pin electrical connector * LED tail lights * Flashing side marker lights ----General attachments: * Support windlass at the front * Enclosed plastic mudguards * Folding underride guard for paver applications ----Chassis: * Chassis made of fine-grain steel ----Tipper body: * Pal.- 3-way tipper body * 700 mm steel front wall * Aluminum side walls, asymmetrical, continuous, without center stanchion, foldable with long travel locks and swinging via manual central locking * 800 mm high steel rear wall with automatic rear wall opening during rear tipping * 4 mm Hardox 450 steel floor ----Load securing: * On each side, 2 pairs of 3 t lashing rings, recessed and foldable in the steel floor ----Paintwork: * Chassis, drawbar, underride guard hot-dip galvanized * Tipper body painted in a RAL color of choice (no special or metallic paint), color can be changed up to approx. 6 weeks before completion ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. calendar week 42/2026

Koşul: yeni, Üretim yılı: 2026, New model, now with 9,900 kg gross vehicle weight! Cable drum transport trailer. Permissible gross weight: 9,900 kg, payload approx. 7,000 kg (standard equipment). Hydraulic lifting and lowering of the cable drum from the towing vehicle or via separate engine (4-stroke petrol, 8.1 kW, electric start) with weather protection cover, hydraulically driven drum with rubber-coated drive rollers, drum diameter 800–3,000 mm, drum width up to approx. 1,650 mm, centring cones for cable drums. Dual-speed support winch at the front, extendable rear support. BPW axle, EBS, parabolic suspension, tyres 315-80R22.5, tyre pressure monitoring. Height-adjustable 40 mm towing eye, 2-line air, LED lighting 12+24 V. Toolbox, advertising panels integrated into the side underrun protection. Fully hot-dip galvanized vehicle. New vehicle including factory warranty. Available from approx. week 26, 2026. (Archive photos) Rodpfx Aeyyhb Neatscb = Further information = Unladen weight: 2,900 kg Payload: 7,000 kg Gross vehicle weight: 9,900 kg Front tyres: 315-80R22.5 Country of manufacture: DE Please contact Jan-Marc Schwickert for further information.

Koşul: ikinci el, azami yük ağırlığı: 7.100 kg, toplam ağırlık: 10.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/2007, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.450 mm, yükleme alanı yüksekliği: 1.100 mm, toplam genişlik: 2.550 mm, Araç / Üst yapı: Tandem üç taraflı damper İlk tescil: 07/07 Rcedpfx Aeyz H Azeatsb Toplam ağırlık: 10.000 kg Boş ağırlık: 2.900 kg Taşıma kapasitesi: 7.100 kg Toplam uzunluk: 6.900 mm Yükleme uzunluğu: 5.000 mm Genişlik: 2.550 mm / yaklaşık yükleme genişliği 2.450 mm Yükleme yüksekliği: yaklaşık 1.100 mm Diğer bilgiler - 40 km/s - 500 mm yan paneller - 500 mm galvanizli ön ek - Yük yüzeyinde 7 çift sabitleme halkası - Üst yapı dışında 4 çift sabitleme halkası - Destek ayağı - Arka destek - Yan panel kaldırma yayı - Opsiyonel rampalar 1.280,00 €

Koşul: ikinci el, boş ağırlık: 3.280 kg, azami yük ağırlığı: 14.600 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 09/2013, süspansiyon: hava, lastik boyutu: 265/70 R19,5, dingil mesafesi: 5.030 mm, Donanım: ABS, | Müller-Mitteltal roll-off trailer | Toolbox | Galvanized | Tires: 265/70R19.5 | BPW disc brakes | TÜV valid until | Subject to errors, input mistakes, and prior sale. Rcsdowd Sdcjpfx Aatob

Koşul: ikinci el, azami yük ağırlığı: 19.800 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2019, Donanım: ABS, * Müller Mitteltal 3 dingilli konteyner taşıma römorku * Tip TM 2 24 Rjdpfx Asyx R Enoatocb * 7 ila 10 m³ arası iki konteyner için * Yük emniyeti her bir konteyner için yalnızca iki zincir ile sağlanır * Çift teker 265/70 R19,5 * Havalı süspansiyon * BPW dingiller * Dönel şasi çeki oku; pnömatik olarak alçaltılabilir ve pnömatik kilit açma mekanizmalıdır * Gergi elemanları takılması için 8 adet 5 ton UVV bağlama halkası * Konteynerlerin yandan merkezlenmesi için 8 adet değiştirilebilir konteyner durdurucu * EBS * Teknik olarak izin verilen toplam ağırlık 27.000 kg

Koşul: ikinci el, boş ağırlık: 8.800 kg, azami yük ağırlığı: 31.200 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 04/1996, yükleme alanı uzunluğu: 10.000 mm, yükleme alanı genişliği: 2.510 mm, yükleme alanı yüksekliği: 1 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: kırmızı, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Araç lokasyonu: Bovenden, 4 akslı, döner tabla, yaprak süspansiyon, 3 metreye kadar genişletilebilir, bağlama halkaları, 2 parçalı rampalar, hidrolik rampalar, arka destek, yan alüminyum yan koruma, çift tekerlek, depolama kutusu. Üst yapı: Hidrolik 2 parçalı rampa ile donatılmış 4 akslı alçak yükleyici dorse. Yükseklik yaklaşık 900 mm. 4x 10 ton SAF aks, kampanalı frenler, 40'lık ve 50'lik çeki halkası! Üst platform uzunluğu yaklaşık 2900 mm! Alt platform uzunluğu yaklaşık 7100 mm! EKİPMAN BİLGİLERİ GARANTİSİZ VERİLMİŞTİR, değişiklik, ara satış ve yazım hataları saklıdır! Rcjdsywvhropfx Aatjb

Koşul: yeni, azami yük ağırlığı: 38.620 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height increases by +30 mm when lifted) * Last axle steered (axle steering lock for maneuvering can be engaged from the driver’s cab without truck-side installation or additionally via a switch on trailer). The lock must be disengaged before entering public roads. * Forced lifting and lowering of the lift axle for maneuvering purposes (requires truck-side installation), with speed-dependent activation via EBS control ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar, 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as info tool with pressure sensors for total axle load display per axle group * Tire pressure monitoring system, displayable in truck via EBS signal (without truck-side installation) * LED lighting system 12/24 V * Removable LED beacon at the rear ----General Attachments: * Mechanical warning sign package for 3 m total width * Toolbox made of galvanized steel sheet approx. 650 x 300 x 600 mm, mounted left side * Front plastic mudguards and rear galvanized steel mudflaps ----Low Loader Deck: * Gooseneck turntable platform with 45° corners and 3 storage compartments with lockable folding lids (rear-opening) * Shortened lowbed platform by 500 mm to 6,280 mm including extended stepped contour, 500 mm forward * Rubber lining on folding frame, drive-on slope and load-bearing surface on the low loader platform * Bamboo wood between the longitudinal beams in front of the excavator stick recess ----Load Securing (LaSi package): * 2 x 6.4 t lashing rings at the front corners * 2 x 13.4 t UVV lashing points per side (front & rear corners) * 5 x 10 t UVV lashing rings per side (pivoting, retractable, loadable in all directions) * 4 stake pockets per side, also providing 2 t lashing capability each * 1 x 16 t UVV lashing point on the rear traverse ----Widening: * Extendable and foldable extension arms for up to 3 m total width (deck board holder under the chassis, right side) ----Excavator Stick Recess: * Fully continuous, reinforced profile from last axle to rear cross member. Approx. L=2,350 x W=770 x D=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for truck hydraulic pump outputs over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Platform Dimensions: * Load area above turntable: 2,600 + 390 x 2,520 mm * Lowbed area: 6,280 + 500 x 2,520 mm, incl. 860 mm drive-on slope Rcsdpfx Aasl Tihujteb ----Paintwork: * Chassis, turntable, drawbar, extension consoles, and loading ramps hot-dip galvanized * Tow bar, axles, hydraulic axle supports, and air tanks painted in black ----Notes: * New vehicle with manufacturer’s warranty * Subject to prior sale and errors ----Delivery Time: Immediately available*

Koşul: yeni, azami yük ağırlığı: 38.620 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, T5 Profile 50.0: ----Braking System: * Wabco EBS (Electronic Braking System) * Emergency release device for spring brake chambers * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm with axle lifted) * Last axle with trailing steering (lockable from cab for shunting without truck-side installation, additionally lockable via switch on the trailer). Lock must be deactivated before entering public roads. * Forced relief as well as forced lowering of lift axle for manoeuvring purposes (truck-side installation required), with speed-dependent control via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as an infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with display function in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24 V * Removable LED beacon at rear ----General Attachments: * Mechanical warning sign kit for 3 m overall width * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, on left side * Plastic fenders at front axle, galvanized sheet steel fender skirts at rear axle ----Low Loader Platform: * Front section of turntable platform with 45° corners and 3 storage compartments with lockable folding lids (lids open to the rear) * Shortening of the low-loader platform by 500 mm to 6,280 mm including extended offset bending by 500 mm to the front * Rubber coating on folding frame, approach slope, and running surface of low loader platform * Bamboo timber between longitudinal beams in front of excavator stick rest ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings in the front corners * 2 x 13.4 t UVV lashing points front and rear on each side * 5 x 10 t UVV lashing rings on each side (pivoting, lowerable, and loadable from all directions) * 4 stake pockets per side, each with 2 t lashing option * 1 x 16 t UVV lashing point at rear cross member ----Widening: * Extendable and foldable widening arms for 3 m overall width (plank holder under the chassis on front right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforcement profile from last axle to rear cross member, approx. L=2,350 x W=770 x H=270 mm, 2 pairs 6.4 t UVV lashing rings on the side in the excavator stick rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and deployable pointed section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump performance in truck over 40 l/min up to max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm via air suspension ----Deck Dimensions: * Platform over turntable: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm incl. 860 mm approach slope ----Paintwork: * Chassis, turntable, drawbar, widening consoles, access ramps hot-dip galvanized * Drawbar, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: Rcjdpfxoxptn De Aatob Available immediately*