Kullanılmış Müller-Mitteltal Etü Fragmanlar satın al (252)

Durumu: yeni, azami yük ağırlığı: 38.900 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (when lifted, ride height +30 mm) * Last axle with forced steering (locking of the trailing axle is possible from the cab for maneuvering purposes without truck-side installation, as well as additionally via a switch on the trailer). The lock must be disengaged before driving on public roads. * Forced raising and lowering of the lift axle for maneuvering purposes (requires truck-side installation), speed-controlled via EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors for total axle load display per axle group * Tire pressure monitoring system with display in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24V * LED beacon (removable) at the rear ----General accessories: * Mechanical warning panel kit for 3m total width * Toolbox made of galvanized steel, approx. 650 x 300 x 600 mm, mounted left side * Plastic fenders front axle and galvanized steel mudguards rear axle ----Low loader platform: * Front section of bogie platform with 45° corners, 3 storage compartments with lockable hinged lids (opening to the rear) * Shortening of low loader platform by 500 mm to 6,280 mm including extended step profile by 500 mm to the front * Rubber coating on the folding frame, ramp incline and running surface of the low loader platform * Bamboo wood between the longitudinal beams in front of the excavator arm storage ----Load securing (LaSi Package): * 2 x 6.4 t lashing rings front corners * On each side, front and rear corners, 2 x 13.4 t UVV lashing points * Additionally, each side with 5 x 10 t UVV lashing points (swiveling, lowerable, loadable in all directions) * Each side with 4 stake pockets, each with a simultaneous 2 t lashing option * 1 x 16 t UVV lashing point on rear crossmember ----Widening: * Extendable and foldable widening supports for 3m total width (plank holder under chassis, right side) ----Excavator arm storage: * Continuous excavator arm holder with reinforcement profile from last axle to end beam, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of the excavator arm holder ----Ramps: * Hydraulic folding ramp with two-line hydraulics and fold-out tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump output on truck of over 40 l/min up to max. 140 l/min) ----Loading height: * Loaded: 890 mm +/- 20 mm due to air suspension ----Loading area dimensions: * Platform over slewing ring: 2,600 + 390 x 2,520 mm * Lowbed loading area: 6,280 + 500 x 2,520 mm, incl. 860 mm ramp ----Paintwork: * Chassis, bogie, drawbar, widening consoles, access ramps hot-dip galvanized * Drawbar, axles, hydraulic axle supports, and air tanks painted black ----Information: * New vehicle with manufacturer's warranty Nksdpfx Afjxptn Djgou * Subject to errors and prior sale ----Delivery time: Available from CW

Durumu: yeni, azami yük ağırlığı: 29.850 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 8.000 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rearmost axle configured as trailing steering axle, with electro-pneumatic steering lock activated by reverse gear PIN * Additional lock for the trailing axle, operated from the tractor unit for maneuvering purposes – installation on the truck side is not required – assigned to PIN 10. The lock must be disengaged before driving on public roads. ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride-through-Reset) function ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck's dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as information tool with pressure sensors for total axle load indication only * 7-pin socket at the rear for extra-length lighting * Removable LED beacon at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing gears * Galvanized steel mudguards * Swivel arm as carrier for connecting lines in front of the front bulkhead ----Warning Package: * Mechanically adjustable warning sign package ----Low Loader Bed: * 50 mm floor made of larch / Douglas fir instead of spruce / fir * Rear incline – 700 mm long – from the fifth wheel platform to the low bed with chequer plate surface, plus a perforated strip at the end for attaching aluminum loading ramps * Chequer plate cover over the wheels * SP-Combo Package: Tool box with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the fifth wheel platform, approx. 2,480 x 500 mm * Folding top lid and side doors in the angled corners * Foldable aluminum side walls 500 mm high on the fifth wheel platform, including folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Prepared for container lock fittings * Prepared for 3 receiving recesses in the entry incline from the low bed to the gooseneck * Prepared for retrofitting folding supports for 3 m extension by welding the mounting brackets into the outer frame ----Load Securing: Fifth-wheel platform: Nodpoykx I Hsfx Afgsku * Front corners and front with 50 mm bores, each for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed into the floor on the sides towards the entry incline * Perforated outer frame, 45° angled, with hole pattern for lashing equipment (2 t lashing points every 480 mm) * 2 x 6.3 t retractable lashing rings on each side integrated into the outer frame Low bed platform: * 2 x 16.5 t lashing rings centered directly in front of the incline to the gooseneck * 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings per side, integrated into the outer frame * 4 stanchion pockets per side integrated into the outer frame * Profifix lashing rail placed centrally along the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From the end of the last fixed axle to the rear crossmember: W = 770 mm, D = 270 mm (2 x 6.4 t lashing rings per side, rigidly welded in the excavator arm rest) ----Ramp: * Hydraulic single-piece "ALLTEC" aluminum access ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp adjustment on guide tube of the ramp

Durumu: yeni, azami yük ağırlığı: 29.850 kg, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 8.000 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes Nodpfx Afoykx I Togeku ----Axles: * 2 x 10 t axles * Rearmost axle configured as trailing steering axle, with electro-pneumatic steering lock activated by reverse gear PIN * Additional lock for the trailing axle, operated from the tractor unit for maneuvering purposes – installation on the truck side is not required – assigned to PIN 10. The lock must be disengaged before driving on public roads. ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride-through-Reset) function ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck's dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as information tool with pressure sensors for total axle load indication only * 7-pin socket at the rear for extra-length lighting * Removable LED beacon at the rear ----General Attachments: * Aluminum air tanks * Mechanical crank landing gears * Galvanized steel mudguards * Swivel arm as carrier for connecting lines in front of the front bulkhead ----Warning Package: * Mechanically adjustable warning sign package ----Low Loader Bed: * 50 mm floor made of larch / Douglas fir instead of spruce / fir * Rear incline – 700 mm long – from the fifth wheel platform to the low bed with chequer plate surface, plus a perforated strip at the end for attaching aluminum loading ramps * Chequer plate cover over the wheels * SP-Combo Package: Tool box with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the fifth wheel platform, approx. 2,480 x 500 mm * Folding top lid and side doors in the angled corners * Foldable aluminum side walls 500 mm high on the fifth wheel platform, including folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Prepared for container lock fittings * Prepared for 3 receiving recesses in the entry incline from the low bed to the gooseneck * Prepared for retrofitting folding supports for 3 m extension by welding the mounting brackets into the outer frame ----Load Securing: Fifth-wheel platform: * Front corners and front with 50 mm bores, each for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed into the floor on the sides towards the entry incline * Perforated outer frame, 45° angled, with hole pattern for lashing equipment (2 t lashing points every 480 mm) * 2 x 6.3 t retractable lashing rings on each side integrated into the outer frame Low bed platform: * 2 x 16.5 t lashing rings centered directly in front of the incline to the gooseneck * 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings per side, integrated into the outer frame * 4 stanchion pockets per side integrated into the outer frame * Profifix lashing rail placed centrally along the longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From the end of the last fixed axle to the rear crossmember: W = 770 mm, D = 270 mm (2 x 6.4 t lashing rings per side, rigidly welded in the excavator arm rest) ----Ramp: * Hydraulic single-piece "ALLTEC" aluminum access ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp adjustment on guide tube of the ramp

Durumu: yeni, azami yük ağırlığı: 8.750 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, Donanım: ABS, hidrolik arka platform, Müller-Mitteltal KA-TA-R 11.9 Tandem Low-Loader Three-Way Tipper Trailer with Ramps Reference Number: 11612 * NEW VEHICLE, not yet registered, now available in RAL 9016 traffic white * Door-to-door delivery available for an additional charge! * Gross weight: 11,900 kg, payload: 8,750 kg * Galvanized floor, 5m x 2.42m x 0.5m; side boards can swing, fold down, and be removed; prepped for later retrofit side board extensions * Front wall hot-dip galvanized * Lockable compartment under the tipping platform for loading ramp * Includes loading ramps 3.31m, 8t per pair * 4 UVV lashing rings LC 5000 daN at front and rear * 8 recessed, folding lashing eyes LC 3000 daN mounted in the tipper floor (centered) * Net hooks * Drawbar continuously height-adjustable, hot-dip galvanized, towing eye 40mm * Galvanized chassis * Tires: 235/75R 17.5 (x4), BPW axles, parabolic springs * Tire pressure monitoring * EBS (Electronic Braking System) * LED lighting system for 12+24 Volt * Side marker lights with indicator activation * Bolted, galvanized rear stanchions * Excavator bucket holder mounted on the front wall --- Please request an individual quote from us! Additional equipment options available. Financing from just €405 net for 72 months with no down payment and no final residual value. An offer from our financing partner "FM LeasingPartner" --- Our Opening Hours Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside of business hours, appointments can be arranged. Nsdpfxjyl Ebps Afgoku WhatsApp Leasing, financing, and trade-ins possible---

Durumu: kullanılmış, azami yük ağırlığı: 9.720 kg, toplam ağırlık: 13.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/1993, yükleme alanı uzunluğu: 5.170 mm, yükleme alanı genişliği: 2.440 mm, yükleme alanı yüksekliği: 1.800 mm, yükleme alanı hacmi: 23 m³, toplam genişlik: 2.500 mm, toplam yükseklik: 3.200 mm, Üretim yılı: 1993, * Salınımlı yan duvarlı üst yapı, büyük tavan altı * Dış çerçeve ve dikmeler paslanmaz çelik * Dekra sertifikalı * Ortada 1 sıra yük emniyeti * Çift kanatlı arka kapı * Lastikler 275/70 R 22.5, %90 * Yüksekliği ayarlanabilir çekme kolu Nkedpfoykxk Iex Afgju * Parabolik süspansiyonlu * Mükemmel durumda

Durumu: kullanılmış, azami yük ağırlığı: 9.720 kg, toplam ağırlık: 13.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 07/1993, yükleme alanı uzunluğu: 5.170 mm, yükleme alanı genişliği: 2.440 mm, yükleme alanı yüksekliği: 1.800 mm, yükleme alanı hacmi: 23 m³, toplam genişlik: 2.500 mm, toplam yükseklik: 3.200 mm, Üretim yılı: 1993, * Büyük döner yan duvarlı üst yapı, çatı altında * Paslanmaz çelik dış çerçeve ve dikmeler * Dekra sertifikalı * Ortada 1 sıra yük güvenliği Nkodpsykxkzjfx Afgju * Arkada çift kanatlı kapı * Lastikler 275/70 R 22.5, %90 * Yüksekliği ayarlanabilir çekme kolu * Parabol süspansiyonlu * MÜKEMMEL DURUMDA

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, Donanım: ABS, * T 3: * ABS braking system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical axle equalization at the rear * Side underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front & rear * Front: closed plastic mudguards; rear: straight galvanized steel skirts, each with spray protection * Reflective contour tape on the sides and rear * Foldable (hot-dip galvanized) cover for the toolbox on the bogie platform * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm - powder-coated in black - mounted on the side under the chassis * 15-pin electrical connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via drawbar spring & turnbuckle * 4 stake pockets on each side (stakes not included) with simultaneous lashing option * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform * 5 pairs of UVV folding and lowering lashing rings * Loadable in all directions, recessed into the external frame at the corners (13.4 t), otherwise 10 t * 6 pairs of mechanical folding outriggers for a total width of 3 m (not at rear chamfer) * Extension planks stored in a compartment under the loading area * Excavator arm rest over the rear axle up to the end crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator arm rest) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable ramp tip and load holding valves, hydraulic lateral ramp shift * Hydraulic flow divider in the trailer (for truck hydraulic pump capacity over 40 ltr. up to max. 140 ltr./min.), dual-line hydraulic system * Loading area above the slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loaded deck height approx. 860 mm +/- 30 mm compensation unit * Chassis, bogie, folding outriggers, drop-down rear supports and ramps hot-dip galvanized * Axles, springs, drawbar, air tanks etc. painted in black * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 19/2026 Nkjdpfx Afeq Dyv Isgeu

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * PT 30 Profile: * EBS (electronic braking system) Nsdpfx Aetplwisfgsku * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lifting and lowering function, including return-to-ride (RtR) valve * Smart-Board installed on the trailer as an infotool (for displaying axle loads – separate display for front and rear) * Tire pressure monitoring system with display option in the truck via EBS signal, no truck-side installation required * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign sets at front and rear * Front axle with plastic quarter mudguards and spray protection * Rear axle with straight, galvanized steel apron and spray protection * Reflective contour tape on the side and rear * 15-pin electrical connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar 1,200 mm long with 40 mm draw eye and height adjustment via draw spring & turnbuckle * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted on the right side * Compartment in the turntable for accessories with folding lid, 2 fixed container locks (directly after the turntable platform) * ROBOT-welded anti-slip covering on the steel plate of the turntable platform (with protruding weld seams) * Load securing package consisting of: 2 lashing eyes (13.4 t) at the front left & right at the bulkhead support, one pair each of UVV lashing rings (13.4 t) front & rear, 3 pairs of swing- and lowerable UVV lashing rings (10 t each) per side, loadable in all directions and integrated into the outer frame, plus 3 stake pockets per side, each with additional 2 t lashing possibility * 6 pairs of mechanical folding outriggers for up to 3 meters total width (not in the rear taper) * Widening planks stored in the center of the cargo area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanical lateral adjustment * 4-section control block prepared for future retrofit of hydraulic ramp shift * Excavator stick support over rear axle, extending to rear cross member (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator stick support, mounted on the side in the longitudinal frame * 2 galvanized steps at the turntable, left & right * Profifix lashing rail along the center longitudinal axis, in flat area, with lashing points up to LC 3000 daN * Chassis, turntable, folding outriggers, drop supports, and loading ramps hot-dip galvanized * Axles, slewing ring, air reservoirs, and drawbar painted in black * Loading edge height laden approx. 910 mm +/- 20 mm (air suspension) * New vehicle with manufacturer’s warranty * Subject to error and prior sale * Available approx. from calendar week 22/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 14.660 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 19.0: Nkedel Th Hwspfx Afgou * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem equalizer assembly * Drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at front * Rear foldable external support legs * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood flooring * Preparation in front of the bulkhead for retrofitting container locks * Bolt-on flat steel bulkhead * Side walls made of trapezoidal-profile steel sheeting, fold-down with drop-side spring lift assist * Steel rear wall, slidable between the ramps, storage mount inside front bulkhead when not in use * Rear stanchions bolted * Perforated outer frame, approx. 45° edged, with 2 t lashing capacity every 480 mm * Option to fit 3 t fold-down lashing rings every 600 mm * In each corner, front and rear, 1 x 10 t lashing ring, multiple holes in the bulkhead and end cross member for 1.2 t lashing points * Profifix lashing rail along the centre axis for lashing capacity up to LC 3000 daN * One-piece mechanical grating ramps with spring mechanism for single-man operation, approx. 2,750 x 620 mm (can be compressed to 20 mm) * Rear approach wedge approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps and support legs hot-dip galvanized * Body side walls painted RAL 9010 pure white * Side walls can be painted in any RAL color for an additional charge * Axles, springs, air tanks, flange eye and landing gear painted in black * New vehicle with full manufacturer warranty * Subject to errors and prior sale * Available approx. from calendar week 21/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 23.830 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.460 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * T3 Profile 30.0: * EBS braking system * TPMS tire pressure monitoring system Nkodpfx Afsl Thxdjgju * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Side underrun protection * Swing-down supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle with closed plastic mudguards; rear axle with straight, galvanized steel skirts, each equipped with spray protection * Contour tape on the sides and rear, reflective * Foldable lid (hot-dip galvanized) for the toolbox on the turntable platform * Multi-voltage system * LED tail lights * Removable rotating beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring and turnbuckle * 15-pin power connector * Four stake pockets on each side (no stakes included) with lashing points * Cargo securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant lashing rings, pivotable and recessed, loadable in all directions and integrated into the outer frame – 13.4 t load capacity in the corners, otherwise 10 t * Six pairs of mechanical folding outriggers for a total width of 3 m (not on the rear slope) * Extension planks stored in the center of the loading bed * Excavator boom support over the rear axle up to the end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the side in the excavator boom support) * One-piece hydraulic loading ramps (approx. 3,000 x 720 mm) * Four-section control block for future retrofitting of hydraulic ramp shift * Mechanical lateral ramp shift * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, turntable, drawbar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * -- Gross weight of 30,000 kg technically possible -- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from calendar week 18/2026

Durumu: yeni, azami yük ağırlığı: 13.700 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TRA 18.0:  * 2 in 1 = suitable for roll-off containers and as a low-loader/platform trailer ---- Brakes: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ---- Axles: * 2 x 10-ton axles ---- Suspension: * Air suspension with lifting and lowering function as well as RTR valve ---- Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and height adjustment ---- Electrics / Lighting: * Tire pressure monitoring with display possibility in truck via EBS signal – no truck-side installation required * LED rear lights 12 / 24 V * 15-pin power connector ---- General Attachments: * Tool box made of powder-coated steel, approx. 1,000 x 300 x 600 mm * Storage box for container nets made of galvanized sheet metal, 960 x 300 x 450/400 mm * Reflective contour tape on sides & rear * Side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * Foldable A-sign at the rear ---- Loading Area: Nsdpfjl Tq Nmox Afgeku * Main frame with raised outer rails for guiding roll-off containers * Steel sheet floor with recesses for rollers in the bogie area * Container length from 5,500 – 7,000 mm possible * Pneumatic 4-point clamp locking system and mechanical plug-in end stops at the front in the guide track, load securing certificate according to DIN 30722 - 1 * Weld bead as anti-slip surface in the drive-on slope area * Mechanical drop legs at the rear ---- Load Securing: * 1 pair of 10 t UVV lashing rings at the front bulkhead crossmember * 3 pairs of 10 t UVV lashing rings on the side outer frame * Each side with 4 x 2 t cloverleaf-style lashing eyes * 4 x 8 t recessed lashing brackets in the outer frame ---- Ramps: * 1 pair of aluminium ramps (10.6 t / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ---- Paintwork: * Chassis, bogie, locking parts, and rear drop legs hot-dip galvanized * But the drawbar, axles, and air tanks painted in a shade of black ---- Information: * New vehicle, unregistered, with full manufacturer's warranty * Subject to errors and prior sale * Sample images ---- Delivery Time: * Available approx. from KW 23 / 2026

Durumu: yeni, azami yük ağırlığı: 13.700 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TRA 18.0: * 2 in 1: Suitable for roll-off containers and as a low-bed trailer ----Braking System: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10-ton axles ----Suspension: * Air suspension with lifting and lowering function and RTR valve ----Drawbar: * Drawbar 2,000 mm long with 40 mm towing eye and adjustable height mechanism ----Electrics / Lighting: * Tyre pressure monitoring system with display in the truck via EBS signal – no installation required on the truck side * LED tail lights 12/24V * 15-pin electrical connector ----General Accessories: * Tool box made from powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Storage box for container net made from galvanized sheet metal, 960 x 300 x 450/400 mm * Reflective contour tape on sides & rear * Side underrun protection * Plastic quarter mudguards with splash guards * Rear plastic impact buffer * Foldable rear A-sign ----Loading Area: * Main frame with raised outer frame for roll-off container guidance * Steel floor with roller recesses in the bogie area * Suitable for container lengths from 5,500 to 7,000 mm * Pneumatic 4-point locking system and mechanically insertable stop angles at the front, load securing certificate according to DIN 30722-1 * Weld bead as anti-slip surface in the ramp running area * Mechanical drop-down supports at the rear ----Load Securing: * 1 pair of 10-ton UVV lashing rings at the front wall cross member * 3 pairs of 10-ton UVV lashing rings on the outer frame * Each side features 4 x 2-ton cloverleaf-style lashing eyes * 4 x 8-ton lashing shackles recessed in the outer frame ----Ramps: * 1 pair of aluminium loading ramps (10.6 tons/pair) 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) ----Paint Finish: * Chassis, bogie, locking components, and rear drop supports hot-dip galvanized * Drawbar, axles, and air reservoirs painted in black ----Information: * New vehicle without first registration with full manufacturer's warranty * Subject to errors and prior sale * Sample images ----Delivery Time: Nkedpfx Afel Tpc Asgeu * Available approx. from calendar week 23 / 2026

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.380 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * PT 30 Profile: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lift and lowering function and return-to-ride (RtR) valve * Smart-board mounted on trailer as info tool (for axle load display – separately for front and rear) * Tyre pressure monitoring with in-cab display via EBS signal, no truck-side installation required * Side underrun protection * Swivel support legs at rear of chassis frame * Mechanically adjustable warning board packages front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight galvanized sheet metal skirts with spray protection * Reflective contour tape on sides and rear * 15-pin electrical connector * LED lighting 12 / 24 V * LED beacon (removable) mounted at rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Toolbox made of galvanized steel approx. 650 x 300 x 600 mm, black powder-coated, mounted right side * Compartment in turntable for accessories with folding lid, 2 container locks permanently installed (immediately after the turntable platform) * ROBOT-WELDED ANTI-SLIP coating to steel turntable platform (protruding weld seams) * Load securing package consisting of: 2 lashing eyes (13.4 t) front left & right on bulkhead carrier, 1 pair each of UVV lashing rings (13.4 t) front & rear, 3 pairs each of UVV lashing rings (10 t) on each side, swiveling and lowerable, loadable in all directions and integrated into the outer frame, 3 stake pockets per side, each with 2 t lashing capability Nksdpfoxptn Rjx Afgeu * 6 pairs of mechanical folding outriggers for 3 m total width (not at rear taper) * Extension planks stored in the center of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way control block for later retrofitting of hydraulic ramp shift * Excavator arm recess over rear axle, continuous up to end crossmember (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in excavator arm recess, integrated in the side longitudinal frame * 2 galvanized steps at turntable left + right * Profifix lashing rail in longitudinal axis, centered in level area, for lashing up to LC 3000 daN * Chassis, turntable, folding outriggers, drop supports and loading ramps hot-dip galvanized * Axles, slewing ring, air tank, towing bar painted in black tone * Loading height loaded approx. 910 mm +/- 20 mm air suspension * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from approx. calendar week 22/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 23.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, Donanım: ABS, * T 3: * ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle equalization at rear * Side underrun protection * Pivoting supports at the rear of the chassis frame * Mechanically adjustable warning panel sets at front & rear * Front axle: closed plastic fenders; rear axle: straight, galvanized steel skirts, each with splash guards * Reflective contour tape on sides and rear * Hinged (hot-dip galvanized) cover for toolbox on the turntable platform * Toolbox made of galvanized steel, approx. 650 x 300 x 600 mm, powder-coated black, mounted laterally under the chassis * 15-pin electrical connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Drawbar with 40 mm towing eye and height adjustment via draw spring & turnbuckle * 4 stake pockets per side (no stakes included), doubles as lashing points * Load securing package including: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and retractable * Loadable in all directions, integrated in outer frame corners 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for overall width of 3 m (not at rear slope) * Extension planks for platform width stored in a storage compartment under loading area * Digger arm cradle above rear axle up to rear crossmember, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings per side in the cradle) * Hydraulically operated folding ramps (approx. 4,650 x 720 mm) with hydraulic movable tip and load holding valves, hydraulically adjustable ramp lateral shift * Hydraulic flow divider in trailer (for truck hydraulic pump performance over 40 l up to max. 140 l/min), dual-circuit hydraulics * Loading area above turntable: approx. 1,960 x 2,520 mm Nsdpfx Afstplwfegjku * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm drive-up slope) * Loaded platform height approx. 860 mm +/- 30 mm with compensation unit * Chassis, turntable, folding outriggers, drop supports at rear, and loading ramps hot-dip galvanized * Axles, springs, drawbar, air tanks, etc., painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 19/2026

Durumu: yeni, azami yük ağırlığı: 14.660 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 19.0: * Wabco EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs – 110 mm wide – with tandem equalizing unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at front * External folding supports at rear * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of bulkhead for retrofitting container locks * Bolted flat plate bulkhead * Trapezoidal-profiled steel side panels, foldable with drop side spring assist * Steel rear wall, retractable between the ramps – bracket for storage in the front bulkhead when not in use * Bolted rear stanchions * Perforated outer frame, approx. 45° angled, with 2 t lashing force every 480 mm Nodpol Th Hlefx Afgoku * Option to fit 3 t recessed lashing rings every 600 mm * In each front and rear corner 1 x 10 t lashing ring, various holes for 1.2 t lashing options in front and rear crossmembers * Profifix lashing rail along center axis for securing up to LC 3000 daN * One-piece mechanical grating ramps with spring mechanism suitable for single-person operation, approx. 2,750 x 620 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, loading ramps, and folding supports hot-dip galvanized * Side panel painting in RAL 9010 pure white * Painting in other RAL shades available on request for additional charge * Axles, springs, air tank, flange towing eye, and landing gear painted black * New vehicle with full manufacturer’s warranty * Errors and prior sale excepted * Available approx. from calendar week 21/2026 * Sample images

Durumu: yeni, azami yük ağırlığı: 23.830 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.460 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Side underride protection * Rear swing-down supports on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle: closed plastic mudguards; rear axle: straight, galvanized steel skirting with splash guards * Reflective contour tape on the sides and rear * Folding lid (hot-dip galvanized) for toolbox on the bogie platform * Multi-voltage system * LED taillights * Detachable beacon at the rear * Towing scissors with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * Four stake pockets per side (stakes not included), also usable as lashing points * Load Securing Package including: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings, foldable and lowerable, loadable in all directions and recessed into the outer frame – corners rated at 13.4 t, others 10 t * 6 pairs of mechanical folding outriggers for a total width of 3 m (not in the rear taper) * Widening planks stowed in the center of the loading area Nksdjl Th Adspfx Afgou * Excavator arm rest above rear axle to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the side of the excavator arm rest) * One-piece hydraulic ramps (approx. 3,000 x 720 mm) * 4-section control block for future retrofitting of hydraulic ramp shifting * Mechanical lateral ramp shifting * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen load height: approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen load height: approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, towing scissors, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Technically permissible gross weight: 30,000 kg-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from CW 18/2026

Durumu: kullanılmış, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 02/2021, bir sonraki muayene (TÜV): 08/2026, yükleme alanı uzunluğu: 4.800 mm, yükleme alanı genişliği: 2.430 mm, yükleme alanı yüksekliği: 500 mm, Donanım: ABS, Müller-Mitteltal alçak şasi damperli römork - Bir araçta hem alçak şasi hem de iki yandan damperli römork - 40 mm çeki halkası - Basınçlı hava fren sistemi - Yükleme ve boşaltma için destek ayakları - Gigant akslar - Lastik ölçüleri: 235/75 R 17,5 - Tambur fren - Boş ağırlık: 3.620 kg - Yükseklik ayarlı çekme kolu Nksdsyk Rfkjpfx Afgou - Muayene son tarihi: 08.2026 - SP son tarihi: 02.2026 - SP son tarihi: - Yükleme alanı uzunluğu: 4.800 mm - Yükleme alanı genişliği: 2.430 mm - Yan tavan yüksekliği: 0,5 m Hatalar ve ara satış ihtimali saklıdır. Dahili araç numarası: 11349.

Durumu: yeni, azami yük ağırlığı: 17.650 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.230 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TP 30.0 with 3 cable drum stands ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering system ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck display via EBS signal – no truck-side installation required * 15-pin electrical connector * 2 additional LED reversing lights (controlled via reverse gear) * LED lighting ----General Attachments: * Aluminum air reservoir * Side-mounted stainless steel toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Flatbed Structure: * Zurr-fix outer frame, 45° bent with hole pattern for lashing means; lashing capacity per lashing point 2,000 kg with a spacing of 480 mm * Option to install 3,000 kg drop-down lashing brackets at approx. 600 mm intervals – delivery includes 12 pcs. 3,000 kg lashing brackets per side * 5 pockets per side in the outer frame for stakes 100 x 50 mm – stakes are not included in the delivery * 30 mm phenolic plywood floor ----Cable Drum Stands: * 3 galvanized cable drum stands secured by container locks, with side forklift pockets, center/center 800 mm (pocket width 185 mm) * Maximum drum diameter 2,600 mm and maximum drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross connection * 6,000 kg drum weight per drum stand * Without drive and drum brake * Support arm with clamping lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotatable ends * 2 locating rings * 2 centering cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for customer-side securing of drums against rotation and unwinding Nkjdpfx Aox Nli Nefgeu ----Loading Height: * Loaded approx. 1,040 mm ----Paintwork: * Chassis, bogie, drawbar, outer frame, underrun protection hot-dip galvanized * Axles painted in a black tone ----Information: * Technical upgrade to 30 t gross vehicle weight possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available from calendar week 28 / 2026

Durumu: yeni, azami yük ağırlığı: 17.650 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.230 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TP 30.0 with 3 Cable Drums (Cable Reel Mounts) ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with raise/lower control ----Drawbar: * Drawbar, 1,800 mm long, with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability on the truck dashboard via EBS signal (no installation required on the truck side) * 15-pin power connector * 2 additional LED reversing lights (activated via reverse gear) * LED lighting ----General Attachments: * Aluminum air tank * Stainless steel side-mounted toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Flatbed: * "Zurr-fix" outer frame, 45° bent, with drilled hole pattern for lashing points, lashing capacity per point: 2,000 kg at 480 mm spacing * Option to install 3,000 kg folding lashing rings at approx. 600 mm spacing – 12 pcs 3,000 kg lashing rings included per side * 5 pockets per side for stake tubes 100 x 50 mm in the outer frame – stakes themselves not included in delivery * 30 mm phenolic resin-coated plywood floor ----Cable Drum Mounts (Drum Supports): Nkjdpfx Aox Nlkasfgju * 3 galvanized cable drum mounts secured by container locks with lateral forklift pockets, center-to-center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with crossbar * 6,000 kg drum weight per cable drum mount * Without drive system and drum brake * Support arm with clamping latch to secure drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 clamping rings * 2 centering cones made from polyamide * 4 pcs 3.2 t lashing eyes on the support arms for customer-provided securing against drum rotation and unwinding ----Loading Height: * Approx. 1,040 mm when loaded ----Paintwork: * Chassis, bogie, drawbar, outer frame, and underrun protection hot-dip galvanized * Axles painted in black

Durumu: yeni, azami yük ağırlığı: 17.650 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.230 mm, yükleme alanı genişliği: 2.480 mm, Üretim yılı: 2026, * TP 30.0 with 3 cable drum supports ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lift and lower facility ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display capability in the truck dashboard via EBS signal -no truck-side installation required- * 15-pin power connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Attachments: * Aluminium air tank * Side-mounted stainless steel toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Underrun protection ----Platform: * Zurr-fix outer frame, 45° angled with hole pattern for lashings, lashing capacity per point 2,000 kg at a distance of 480 mm * Option for installation of 3,000 kg drop lashing rings at intervals of approx. 600 mm - delivery includes 12 each side, 3,000 kg lashing rings- * 5 pockets each side for stake posts 100 x 50 mm in the outer frame - stake posts are not included in delivery- * 30 mm phenolic plywood floor ----Drum Supports: * 3 galvanized drum brackets, secured via container locks, with side forklift pockets, center/center 800 mm (width of pockets 185 mm) * Max. drum diameter 2,600 mm, max. drum width 1,650 mm * Internal width between support arms approx. 1,775 mm, with cross brace * Max. drum weight per support 6,000 kg * Without drive and drum brake * Support arm with locking device for securing drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 locating rings * 2 centering cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unwinding Nedpfxox Nlkge Afgeku ----Loading Height: * Approx. 1,040 mm loaded ----Paintwork: * Chassis, turntable, drawbar, outer frame, underrun protection hot-dip galvanized * Axles painted in black shade ----Information: * Technical GVW upgrade to 30 t possible * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available from week 28/2026

Durumu: yeni, azami yük ağırlığı: 14.620 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2026, * RA-T 18.0 / 018: Nsdpsv Nulzofx Afgeku * Wabco EBS-E (electronic braking system) * TPMS (Tire Pressure Monitoring System) * Emergency release system for spring brake cylinders * Disc brakes * 2 x 10 t BPW wide-track axles * Air suspension (automatic lowering when disconnecting the brake) * Drawbar approx. 2,300 mm long with 40 mm towing eye and height adjustment via traction spring & turnbuckle * Plastic toolbox 450 x 470 mm, right side * Side-mounted storage box 1,000 x 500 x 500 mm * Enclosed plastic fenders front & rear axle * Closed side underrun protection, usable as advertising panel * Rear underrun guard * Plastic bumper buffers at the rear * Hazardous goods sign at the rear * 15-pin electrical connector * LED tail lights * Conveyor (roller) track length approx. 6,830 mm * Pneumatic 4-point clamp lock * Mechanically adjustable stop brackets (2 positions) front left and right on the running tracks * 265/70 R 19.5 twin tires * Curb weight 3,220 kg * --Technical gross vehicle weight rating of 20,000 kg possible-- * Approx. 1,130 mm ride height when loaded * Suitable for container lengths of 5,500 - 7,000 mm * Hot-dip galvanized chassis * Air tanks, axles, kingpin plate and drawbar * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 38.290 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2025, * TS 3 Profile 30.0: ----Braking System: * Wabco EBS-E (Electronic Braking System) * Emergency Release Device for Spring-Loaded Cylinders * Drum Brakes ----Axles: * 3 x 11 t BPW Eco Plus Axles * Rear axle with steered trailing axle and electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering system as well as RtR-valve ----Electrical / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an infotool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12 / 24V * Removable LED beacon at rear left ----General Attachments: * Side underrun protection * Landing gear at the front and mechanical swing supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder under the chassis, right side ----Low Loader Deck: * Fifth wheel platform with 45° chamfered front corners and front toolbox made of galvanized steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high side aluminum drop sides (RAL 9010 pure white) foldable and removable on the fifth wheel platform * Rear wall -150 mm- pluggable * Rear slant on the fifth wheel platform to the low bed, approx. 700 mm long * Fifth wheel platform with 50 mm timber flooring and low bed platform with 60 mm timber flooring * Checker plate above the axles ----Widenings: * 8 x mechanical folding extensions to 3 meters total width, but not in the rear slant (extension planks available and stored on the platform) * Mechanically adjustable warning panel sets at front and rear ----Load Securing (Load Securing Package): * On the fifth wheel platform, 2 x 6.3 t lashing rings each, and 3 x 5 t lashing bars per side in the outer frame * On the low bed platform, 2 x 13.4 t lashing rings per side and 4 x 10 t lashing rings, pivotable and lowerable, recessed into the outer frame * 2 x 6.4 t lashing points per side, and 1 lashing ring in the excavator arm trough at the rear * 2 x container locks directly after the cranked section in the low bed platform ----Excavator Arm Trough: * Continuous excavator arm trough from the end of the last rigid axle over the steering axle to the rear crossbeam with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanically single-piece, hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) Nkodpfx Afjl Tnvgjgsu * 4-way control block for the customer's retrofitting of hydraulic ramp shifting * The outer board on the ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp as well as on the entry slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output on the truck from over 40 l up to 120 l/min) ----Loading Dimensions: * Fifth wheel platform loading area: approx. 3,935 x 2,480 mm * Low bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm entry slope) ----Fifth Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, landing gear, air tanks painted black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer warranty * Subject to errors and prior sale * Sample images may contain equipment features not included in the offered vehicle ----Delivery Time: * Available from calendar week 26/2026

Durumu: yeni, azami yük ağırlığı: 38.290 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.520 mm, Üretim yılı: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Rear axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering system as well as Run-on-Ready (RtR) valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control panel mounted on trailer as an infotool with pressure sensors for axle load display * 15-pin power socket * LED lighting system 12 / 24V * Rear left removable LED beacon ----General Attachments: * Lateral underrun protection * Front landing gears and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel carrier under chassis, right side ----Low Loader Deck: * Fifth-wheel platform with 45° chamfered front corners and toolbox at the front made of galvanized steel sheet, W = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm high aluminium drop sides (RAL 9010 pure white) on the sides of the fifth-wheel platform, foldable and removable * 150 mm high removable rear drop board * Rear slope on the fifth-wheel platform to the low bed, approx. 700 mm long * Fifth-wheel platform with 50 mm timber planks, low-bed platform with 60 mm timber planks * Chequer plate over the axles Nedpfx Afjpk D I Asgeku ----Extensions: * 8 x mechanical folding extensions to a total width of 3 m, but not on the rear slope (extension boards included, with storage on the fifth-wheel platform) * Mechanically adjustable warning sign sets front and rear ----Load Securing (Lashing Package): * On the fifth-wheel platform, each 2 x 6.3 t lashing points and 3 x 5 t lashing bars on each side of the outer frame * On the low-bed platform, each side 2 x 13.4 t lashing rings and 4 x 10 t lashing rings, pivoting and retractable, integrated in the outer frame * Each side 2 x 6.4 t lashing eyes and 1 lashing point in the excavator arm recess at the rear * 2 x container locks directly after the step in the low-bed platform ----Excavator Arm Recess: * Continuous excavator arm recess from end of last rigid axle over steering axle to end cross-member, with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanically single-piece, hot-dip galvanized, hydraulic ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way valve block for future retrofit of hydraulic ramp sliding by customer * Outer plank on ramp made from 50 mm hardwood * Climbing strips on outer frame of ramp and on approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump output in truck from over 40 l/min up to 120 l/min) ----Loading Dimensions: * Loading surface of fifth-wheel platform: approx. 3,935 x 2,480 mm * Low-bed loading surface: approx. 8,500 x 2,520 mm * Unladen deck height approx. 910 mm (incl. 860 mm approach slope) ----Fifth-Wheel Height: * Approx. 1,220 mm (suitable for 2-axle and 3-axle tractor units) ----Painting: * Chassis, ramps, rear folding supports, extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in black tone * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and intermediate sale excepted * Sample images may show equipment not included on the offer ----Delivery Time: * Available from week 26/2026

Durumu: kullanılmış, dingil konfigürasyonu: 2 dingil, yükleme alanı hacmi: 10 m³, toplam uzunluk: 7.500 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 4.000 mm, Üretim yılı: 2012, Kullanılabilir malzeme: Beton Boş ağırlık: 6.530 kg Yük kapasitesi: 25.470 kg Azami toplam ağırlık (zGG): 32.000 kg Nedpfox Utq Sjx Afgoku

Durumu: yeni, azami yük ağırlığı: 8.750 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Donanım: ABS, hidrolik arka platform, Reference number for inquiries: 23185L Financing price: €26,800 net plus 19% VAT. Nksdpfoykgnbox Afgeu * Now affordable hire purchase: * e.g. €520 net per month for 60 months, no down payment, no final installment. * An offer from our financing partner FM LeasingPartner * We will be happy to send you a non-binding quotation. Financing price: €26,800 net plus 19% VAT. Available immediately New Müller-Mitteltal KA-TA-R 11.9 tandem low-bed three-way tipper trailer with ramps * Tyres: 385/55 R19.5 (4 units), BPW axles, parabolic springs, drum brakes * Gross weight: 11,900 kg, payload 8,750 kg * Tyre pressure monitoring with display option in the truck via EBS signal * EBS 24 Volt * Side marker lights with indicator activation * LED lighting system for 12+24 volts * 2 LED reversing lights at the rear (suitable for 12 V and 24 V) * Floor galvanised, 5m x 2.42m x 0.5m, side walls laser-welded, swinging, folding and removable * Preparation for future installation of additional side wall extensions * Laying cables for the rear wall * Lockable compartment under the tipping platform for loading ramp * Including aluminium ramps, 8 t load capacity, 3.57 m long, stored in the ramp tray under the tipper body * Front wall hot-dip galvanised * 4 UVV lashing rings LC 5000 daN at the front and rear + 8 lashing eyes LC 3000 daN recessed and foldable in the tipper floor (centered) * Stepless height-adjustable drawbar, hot-dip galvanised, towing eye 40 mm * Net hooks * Bolted, galvanised rear stanchions * One plastic toolbox on the right-hand side of the chassis frame * Step in front of the front wall We are Müller-Mitteltal authorized partner Our business hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside these hours available by appointment. Wir sprechen deutsch, we speak English, mowimy po polsku, on parle français. WhatsApp Leasing, financing, and trade-in available.