Kullanılmış Stas Agrostar Yarı Römorklar satın al (115)

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2008, yükleme alanı uzunluğu: 9.700 mm, yükleme alanı genişliği: 2.350 mm, yükleme alanı yüksekliği: 2.165 mm, yükleme alanı hacmi: 50 m³, Chassis ALU chassis, aluminium alloy 5383H34 Two fully automatically welded T-profiles (width 200 mm) Corrosion protection between steel and aluminium parts, continuous rubber strip pressure-bonded to the longitudinal members, maximum stability via integrated tipping shaft with wear-resistant, pressed-in special bushings, chassis width approx. 1,600 mm, air and electrical lines integrated in a plastic conduit Axles and Suspension, Disc Brakes Jost-disc axle units 3 x 9 tonnes with DCA air suspension, lift and lower valve, load gauge, 3rd axle automatically liftable Tyres and Wheels 6 wheels with tyres size 385/65 R 22.5 approx. 50-60% tread on silver steel rims, 11.75x22.5 ET 120 Hedpfx Aexf Spfofgei Landing Legs Mechanical support legs, load capacity 2 x 20 t, swing feet used for air suspension Brake System According to E.C. standard, two-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E system 2S/2M, with RSS (Roll Stability Support), ALU air tank Electrical System According to StVZO regulations, with two 5-chamber Aspöck LED tail lights, 24 Volt system with two 7-pin and one 15-pin socket at the front, EBS socket, with LED side marker lights, 2 clearance lights, 2 separate LED reversing lights Tipping Body / Dump Bed ALU dump body, side walls with welded vertical aluminium profiles, floor approx. 6 mm in highly wear-resistant aluminium alloy (5383H34), Brinell HB 110, front wall angled design in 4 mm ALU with reinforcing profiles for hydraulic cylinder mounting, side walls in 3 mm hard alloy, straight rear wall, automatic pneumatic (lockable) universal tailgate with pendulum and 2/3-1/3 barn door configuration, double hinge, made from 4 mm thick aluminium, 1 grain chute with water protection, wear plates fitted on side approx. 400-1,000mm x 3,000mm x 4mm Hydraulic System Hydraulic cylinder mounted at the front wall, operating pressure 150 bar, brand Edbro, with approx. 2 m hydraulic hose and 1" quick-release coupling Accessories 6 Parlok plastic mudguards with 2 Stas splash guards, 3 m aluminium ladder, reinforced and foldable underrun protection with 2 towing eyes, one foldable side underrun guard, catwalk on front wall with access ladder (left side), 3 swivelling ALU bows, 1 central additional bow holder, rolling tarp with aluminium tube in centre, rolling tarp system, approx. 660g/m² quality, tarp fastener with quick-action lock (no lashing straps), wheel brace, 2 chocks, toolbox type 800, continuous splash flap on underrun guard, etc. Offer and images are subject to prior sale/change.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2017, yükleme alanı uzunluğu: 10.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 1.900 mm, yükleme alanı hacmi: 50 m³, Chassis light version Aluminium (15-6-12) Two fully automatically welded I-section longitudinal beams with welded cross members. Chassis width approx. 1,600 mm Axles and Suspension Disc brakes 430 mm "Off Road Version" SAF Intradisc axle units 3 x 9 t with SAF air suspension, central air bag arrangement next to the chassis longitudinal beams, 1st axle liftable with drive-off aid and manual forced lowering, Smart Board info center, lift-lower valve, 3rd axle with trailing steering, electrically lockable, Tyres and Wheels 6 wheels fitted with 385/65 R 22.5 tyres, approx. 40-50 % tread remaining, with Alcoa aluminium rims "satin" 11.75 x 22.5 ET 120, UNI-wheel bolts for aluminium rims Landing Gear Mechanical version with single-side operation, 2 speeds, with swing foot for air suspension, 2x20t static load capacity Braking System According to E.C. standards, twin-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E including RSS (Roll-Stability-System), Wabco Smartboard info center, aluminium air reservoir system Electrical System According to StVZO regulations, with 2 five-chamber lamps type Aspöck Ecopoint 2, 24-volt system with 2x7- and 1x15-pin sockets, with lateral outline marker lights, 2 separate LED reversing lights at the rear. All air and electrical lines neatly installed in plastic tubing. Tipping Body/Bin Body, fully welded interior Aluminium bin, side walls made of 30 mm thick plank profiles (2-3 mm), 600 mm wide, welded, floor 8 mm thick high wear-resistant alloy (5383H34/HB 110), bulkhead 4 mm reinforced in straight version, rear wall as double swing doors in straight version with 2 half/half doors each with a grain chute, pneumatic floor vibrators underneath, rear hanger made of aluminium, swing-out, two hold-downs with rubber buffers on the tipper bin attached to the frame at the bulkhead, Hodpfx Aoxf Sn Iefgoi Hydraulic System Tipping cylinder with "cardan" mounting, 7,630 mm stroke Hydraulic cylinder mounted to the bulkhead, working pressure 220 bar, make Hyva, 220 bar with approx. 2.5 m hydraulic hose and loose half 1", tipping angle approx. 48° Accessories 6 Parlok mudguards, full-width spray flaps fitted to underrun protection, aluminium spare wheel holder, foldable lateral underrun protection right-hand side, large 860-type toolbox, approx. 3 m aluminium ladder, 3 mid-position, approx. 150 mm raised swing bars, rolling tarp with central light strip and separate reinforcements at wear points, approx. 660 g/m² quality, with rolling tarpaulin system, perimeter rubber cord in rear end of tarp with two tension hooks to fix onto the rear swing bar, catwalk on bin with access on left, side tarp lock with tensioning straps, rear tarp closure with welded-in rubber cord for water resistance, robust foldable aluminium underrun guard with two towing eyes left and right including locking pins, 2 "Clear-Pass" spray flaps on the mudguard to EC standard, etc. Offer and images non-binding.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2021, yükleme alanı uzunluğu: 9.700 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.200 mm, yükleme alanı hacmi: 53 m³, Chassis, Lightweight Version Made of aluminum (15-6-12) Two fully-automated, welded I-beams longitudinally, with welded cross members. Chassis width: 1,600 mm Axles and Suspension: 430 mm disc brakes, 'Off-Road Version', SAF Intradisc Light axle units, 3 x 9 t with SAF air suspension, centrally aligned with the chassis longitudinal member, 1st axle liftable via air bags with starting aid and manual forced lowering, SmartBoard info center, Hebert lowering valve, front load pressure gauge Wheels and Tires on Aluminum Rims 6 wheels with 385/65 R 22.5 tires, approx. 50% tread, wheels 11.75 x 22.5 ET 120, UNI wheel bolts for alloy rims Kingpin 2” screw-in on an 8 mm thick 'light' mounting plate Landing Legs Support winches, each with 20 t capacity, swing foot for air suspension Brake System According to EC standards, dual-line Wabco system, spring-loaded parking brake acting on two axles, and Wabco EBS-E incl. RSS (Roll Stability System), Wabco SmartBoard Info Center, aluminum air tank system Electrical System According to German Road Traffic Licensing Regulations (StVZO), with 3 round triple-chamber Aspöck tail lights, 24-volt system with 2x7-pin and 1x5-pin sockets, 2x7 side marker lights, 2 centrally mounted LED reversing lights, 1 round fog lamp, 4 LED work lights, 1 interior LED light, 4 red LED position lights in rear door frame All air and electrical lines are properly laid in plastic conduits! Tipper Body / Tipping Body, "Smooth Construction" Body internally fully welded, aluminum tipping body, 30 mm thick plank profiles (2-3 mm), 600 mm wide welded side panels, Hsdpfx Afeyiw T Eogji 8 mm thick highly wear-resistant floor alloy (5383H34/HB 110) with 90° profile to side wall, 4 mm reinforced, straight front wall, universal straight rear door with two half-and-half swing doors and a grain chute, universal door automatic pneumatic operation with separate lockable lever, swingable ALU rear hoop, two hold-downs with rubber buffers on the tipper body fixed to the front wall frame. Hydraulic System—Tipping Cylinder with "Cladding" Mounting Hydraulic cylinder mounted on front wall with working pressure of 150 bar, Edbro brand, with approx. 2.5 m hydraulic hose and loose end 1”, tipping angle appx. 48° Accessories 6 Parlok mudguards, full-width splash guard mounted on underrun protection, no spare wheel holder, foldable aluminum side underrun protection (right), large Type 860 toolbox, approx. 3 m aluminum ladder, 3 central aluminum swing hoops, approx. 150 mm raised, additional mid mount, roll tarp with central skylight and extra reinforcement in wear areas, quality approx. 660 g/m², roll tarp system with quick-tension closure, all-round rubber rope at rear with two tension hooks to fasten on rear swing hoop, walkway on the frame, rear tarp edge has welded-in rubber cord for water protection, robust foldable underrun guard, 2 "Clear-Pass" spray flaps on the mudguard (EU standard), ALU grain funnel with dust sack fixed to the side of the frame, holders for shovel, broom, and scraper above the axles, etc. Unladen weight: 5,950 kg Offer and images non-binding.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2013, yükleme alanı uzunluğu: 9.700 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 1.900 mm, yükleme alanı hacmi: 46 m³, Chassis, lightweight version In aluminium (15-6-12) Two fully automatically welded I-section longitudinal beams with welded cross members. Chassis width: 1,600 mm Hsdpfx Afeyiw T Ssgei Axles and suspension, disc brake 430 mm "off-road version" SAF Intradisc light axle assemblies, 3 x 9 t with SAF air suspension, air bellows centrally aligned to the chassis longitudinal beams. 3rd axle liftable with starting aid and manual forced lowering, Smart Board Info Center, raising/lowering valve, BVA brake wear indicator Tyres and Wheels 6 wheels with tyres size 385/65 R 22.5 approx. 60-70% tread remaining, silver steel rims, 11.75x22.5 ET 120, UNI-wheel bolts Kingpin 2" – bolted into an 8 mm thick plate Landing Legs Mechanical support winds, 2-speed, 2x20t load bearing capacity, with swivel base for air suspension Brake System According to E.E.C. standards, dual-line Wabco system, spring-loaded parking brake acting on two axles, and Wabco EBS-E incl. RSS (roll stability system), Wabco Smartboard Info Center, aluminium air tank system Electrical System Compliant with StVZO regulations, with 2 five-chamber Aspöck lamps, 24V system with 2x7- and 1x15-pin sockets, featuring side marker lights, 2 separate halogen reversing lights, all air and electrical lines neatly routed in plastic conduits Tipping Body/Tipper Body “smooth design”, fully welded on the inside Aluminium tipper body, sidewalls made of 30 mm thick plank profiles (2-3 mm), 600 mm wide, welded; floor 6 mm thick, high-wear resistant alloy (5383H34/HB 110) with 45-degree chamfer to the sidewall; front wall 4 mm reinforced, slanted design; rear wall as universal door, straight, with two wing doors in 2/3-1/3 configuration, fitted with a grain slide; ALU round profile welded to side and bottom of rear doors to seal the door gap; rear doors partially clad smooth in aluminium; operation of the universal door is automatic-pneumatic with separate lockable lever; rear bow swing-out in ALU; two hold-down clamps with rubber buffers attached between the tipper body and the frame at the front wall Hydraulics Tipping cylinder with "Rotulen" suspension (light version). Hydraulic cylinder mounted on the front wall with an operating pressure of 150 bar, make Edbro with approx. 2.5m hydraulic hose and 1" quick coupling, tipping angle approx. 48 degrees Accessories 6 Parlok mudguards, complete with splash guards spanning the entire vehicle width attached to the underrun protection, without spare wheel holder ALU, collapsible side underrun protection on the right, large toolbox type 860, approx. 3 m aluminium ladder, 3 aluminium folding bows raised by approx. 150 mm centrally; additionally, one centrally mounted bow holder for positioning a total of 2 bows to increase loading width; rolling tarpaulin with central light strip and separate reinforcements in wear areas, approx. 660 g/m2 quality with rolling tarp system; all-round elastic cord at rear closure of tarp, with two tension hooks attached to the rear swing bow; catwalk on the frame in chassis color with access steps left and right; side tarp lock with quick release closure; rear tarp closure with welded-in elastic cord for water resistance; robust foldable underrun protection in aluminium; 2 "Clear-Pass" splash guards on the mudguards as per EC standard; laterally attached to the frame is an ALU grain hopper with tarpaulin sack; holders for shovel, broom and scraper mounted above the axles, etc. Unladen weight: 5,960 kg Offer and images subject to change.

Durumu: kullanılmış, azami yük ağırlığı: 33.707 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2025, bir sonraki muayene (TÜV): 09/2026, yükleme alanı uzunluğu: 8.912 mm, yükleme alanı genişliği: 2.400 mm, yükleme alanı yüksekliği: 2.285 mm, yükleme alanı hacmi: 50 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.672 mm, Üretim yılı: 2025, Donanım: ABS, STAS 3-Axle Hardox Steel Tipper 50 cbm "EXTREME" Rock Tipper First registration 09/2025, condition NEW Internal dimensions (LxWxH): 8,912 x 2,350/2,450 x 2,285 mm (tapered body in width) Unladen weight: 8,293 kg Z-chassis, cranked design Floor made of continuous 6 mm Hardox steel HB450 4 crusher bars evenly distributed along the entire length of the floor, fully welded Hodpfx Afsxriu Ejgoi Front wall and side walls made of 5 mm Hardox steel HB450 Inclined front wall, with internal access ladder Deflector plates along the full length of side walls (to protect mudguards) Hydraulic rear wall flap (with pendulum function) HYVA tipping cylinder, Alpha type, suitable for high and low pressure ALU landing legs, full load capacity 2x air vibrators mounted under the body SAF axles with large 430 mm disc brakes 1st axle is a lift axle with starting aid WABCO Trailer-EBS with anti-skid RSS WABCO Smartboard Automatic tipping lowering system Lifting and lowering device Tyres: 385/65 R 22.5 Aluminium access ladder Shovel and broom holder Tool box on the right 4x LED reversing lights RENTING is the new BUYING – with us also available IMMEDIATELY in FULL-SERVICE RENTAL-----

Durumu: kullanılmış, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2023, Üretim yılı: 2023, Donanım: ABS, Besuchen Sie unsere Webseite, wo Sie unseren vollständigen Fahrzeugbestand mit zahlreichen weiteren Fotos und Informationen in mehreren Sprachen finden. SEL 8346 STAS S3000ZX deutsche Zulassung / 1. Hand Erstzulassung: 06.02.2023 Baujahr: 2023 Techn. Gesamtgewicht (kg): 42.000 Zulässiges Gesamtgewicht (kg): 42.000 Leergewicht (kg): 7.990 FIN: YE6S300ZXN0009 HU: 03.2026 BEREIFUNG UND ACHSEN: Bereifung: 385/65 R 22,5 Achskonfiguration: 3 Achsen Jost Luftfederung Scheibenbremsen AUFBAU Innenmaße: Höhe (m): 2,81 (2,67) Hjdoygp Ivspfx Afgji Breite (m): 2,48 Länge (m): 13,50 WEITERE SPEZIFIKATIONEN: Portaltüren FAHRZEUGUNTERLAGEN: Zulassungsbescheinigung Teil I (Schein) Zulassungsbescheinigung Teil II (Brief) COC (Übereinstimmungsbescheinigung) M. BUFANO m. (Italienisch, Englisch, Deutsch) J. CORDEIRO j. (Portugiesisch, Spanisch, Italienisch, Englisch) J. MARJANOVIC j. (Deutsch, Bosnisch) L. OBODYNSKA Ukrainisch/?????, Russisch/??-?????) Wir sprechen: DEUTSCH, ENGLISCH, ITALIENISCH, SPANISCH, PORTUGIESISCH, UKRAINISCH, RUSSISCH, POLNISCH, BOSNISCH Obwohl alle Anstrengungen unternommen wurden, um die Richtigkeit der Angaben zu gewährleisten, übernehmen wir keine Haftung für eventuelle Fehler oder Auslassungen. Wir bitten unsere Kunden, die verfügbaren Fotos zu prüfen. Die angegebenen Maße sind Circa-Angaben. Unsere Fahrzeuge werden im aktuellen Zustand verkauft. Wir laden unsere Kunden ein, unser Unternehmen zu besuchen, um sich persönlich vom Zustand des Fahrzeugs zu überzeugen. Zudem bieten wir die Möglichkeit zu einer Probefahrt an. Es ist zu beachten, dass die mit dem Fahrzeug gelieferten Batterien diejenigen sind, die aktuell eingebaut sind. Sollten Sie neue Batterien wünschen, informieren wir Sie gerne über die Preise.

Durumu: yeni, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.535 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.650 mm, yükleme alanı hacmi: 93 m³, Chassis Version with reinforced continuous frame, newly manufactured superstructure in self-supporting design with corresponding reinforcements in the lower chord for particularly high stability and strength, cross members 140 mm high in reinforced design (for high ground load capacity), additional reinforcement as gusset plate in the front lower chord/vehicle frame area, chassis made of galvanized steel up to the support assembly (trailer construction max. 39,000 kg). Axles and Suspension "Disc brake 22.5" Jost (DCA) axle assemblies, 3x9 tonnes with DCA air suspension, raise and lower function, Wabco Smartboard infotainment center, electronic brake lining wear indicator (BVA) readable in the tractor unit (display), first axle with start-up aid (new EU regulation, without tractor unit equipment) (optional: 1st and 3rd axle liftable). Hodpfx Asyh S Aiofgji Tyres and Wheels 6 wheels fitted with tyres size 385/65 R 22.5 of manufacturer's choice (Br-Go-Co) on silver steel rims, 11.75x22.5 ET 120. Landing Legs Mechanical landing gears with two speeds, 2x 20 tonnes load capacity with swivel foot. Brake System In accordance with EU standard; EBS electronic system Wabco with RSS (Roll-Stability-Support) and premium modulator, spring-loaded parking brake system operating on two axles with controls at the rear, ALU air reservoir system. Electrical System According to the guidelines of EU standard 91/633 and 97/28, with 2 five-chamber lamps type Aspöck Europoint 3 integrated into the aluminium rear cover, 24 Volt system with 1x 15-pin and 2x 7-pin sockets, with LED side marker lights, 2 reflective panels on the rear, position lights front 2x white, rear 2x red, 2 separate LED reversing lights integrated into the underrun protection. Superstructure / Tipper Body "Body fully welded inside" Reinforced side walls, front wall load 17,250 daN, side and rear wall 13,400/10,400 daN. Aluminium tipper body, side walls 30 mm thick ALU plank profiles (2-3 mm), 600 mm wide, fully welded with upper and lower chord, plank profiles fully welded inside, floor as moving floor system mounted on 140 mm ALU crossmembers, forklift floor load approx. 9 t/m², crossmembers closely spaced (approx. 350 mm), ALU front wall with 600 mm plank profile, 2-3 mm thick, in straight design, special ALU corner profiles in chamfered design, smooth rear wall in straight design with 2 ALU swing doors 50/30 mm thick, with 2 locking bars locked in a welded ALU rear frame, mounted with Teflon and Inox bearings, doors secured when open with one chain each side, reinforced wear plates on the side walls approx. 2,000x1,500x4 mm, fully welded, moving residue discharge wall with Kevlar tarp approx. 1,800 mm long plus side Kevlar tarp seals, service door in front wall with ladder folding inward. Hydraulic System "Cargo Floor" Moving Floor System Moving floor system in floor with hydraulically operated ALU profiles on ALU box section profiles with approx. 880 PE-HD sliding blocks plus anti-lifting sliding bearings, Type CF 10 mm floor version, hydraulic stroke approx. 200 mm working travel, fixed ends on front wall, separate option for connecting hydraulic lines under the vehicle with fixed couplings, line size NW 21, fixed couplings with size and type to be specified, operating pressure 190–max. 240 bar, ALU end pieces welded in moving floor, electronic controls rear left with radio control integrated in lockable waterproof box, without hydraulic hoses. Accessories 6 PVC mudguards with 2 anti-spray mud flaps,

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2021, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.675 mm, yükleme alanı hacmi: 87 m³, Chassis Manufactured in self-supporting aluminum construction with corresponding reinforcements in the lower belt for particularly high stability and strength. Equipment chassis made from aluminum, frame height 140 mm! (max. 39t) Axles and Suspension "Disc Brake 22.5" Jost axle assemblies, 3 x 9 tons with DC air suspension, Wabco Smartboard, electronic brake wear indicator (BVA) for display in the tractor unit (without tractor unit equipment), 1st and 3rd axles separately liftable with starting aid (without tractor unit equipment), 3rd axle additionally with Optiturn, ECAS air suspension Tyres and Wheels 6 wheels with 385/65 R 22.5 tyres, approx. 50% tread remaining, mounted on Alcoa aluminum rims, satin finish, 11.75x22.5 ET120 Landing Gear Aluminum two-speed landing legs, manufacturer Alu Leg, with 2x10 t static load capacity; for air suspension, we use swiveling support feet Brake System Hjdjxuy I Iepfx Afgoi According to E.G. standards, two-line braking system, EBS E-system by Wabco with RSS system (Roll-Stability Support), spring loaded brake system acting on two axles with controls at the rear, aluminum air reservoir system, premium modulator Electrical System According to StVZO regulations, with 2 LED five-chamber tail lights of the Aspöck Europoint III type integrated in the aluminum rear closure, 24-volt system with 1x 15-pin and 2x 7-pin sockets, with lateral LED marker lights, 2 separate LED work lights at the rear, 2 LED work lights at the side at the height of the landing gear, 1 LED work light inside front left, operable from outside Body/Tipper Body "Interior Fully Welded" Front wall load 17,250 daN, rear and side walls 10,250/13,400 daN. Aluminum tipper body, side walls made from 30 mm thick aluminum plank profiles (2-3 mm), 600 mm wide, fully welded with lower and upper belts, plank profiles inside fully welded. Floor designed as moving floor system on 140 mm aluminum cross members, cross members closely spaced (approx. 350 mm). Aluminum front wall with 600 mm plank profile, 2-3 mm thick, in straight design. Special aluminum corner profiles in chamfered design, smooth straight rear wall with 2 aluminum swing doors, 50/30 mm thick, with 4 locking rods fitted in a welded aluminum rear frame, mounted in Teflon and stainless steel bearings. Movable aluminum wall suspended in the reinforced upper belt with "Kevlar cover" for complete emptying, side brush sealing and additional Kevlar cover, integrated grain funnel with cover plate - operable from the outside with inspection window at the rear left, 2 sampling slides in the rear doors. Hydraulic System "Cargo Floor" 24-Slat System Moving floor system in the floor with hydraulically operated aluminum profiles on aluminum square profiles, supported by approx. 880 PE-HD sliders, floor approx. 6 mm smooth, hydraulics with approx. 200 mm working stroke, stationary halves at the front wall, separate option for connecting the hydraulic line under the vehicle with stationary halves, line size NW 21, stationary halves with suitable size and design as yet to be specified, operating pressure 190 – max. 240 bar, aluminum end pieces welded into the floor, operation at the rear left with radio remote control in a lockable, waterproof box, without hydraulic hoses. Accessories PVC mudguards with rubber mud flaps, aluminum spare wheel holder, foldable aluminum side underrun guard, one toolbox approx. 800x460x430 mm made of plastic, approx. 3.7 m aluminum ladder, tarpaulin 680 g/m² quality with rolling tarp

Durumu: yeni, azami yük ağırlığı: 28.320 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.535 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.750 mm, yükleme alanı hacmi: 92 m³, Donanım: ABS, Chassis: Constructed with a continuous frame, newly manufactured in a self-supporting aluminum (ALU) design featuring appropriate reinforcements in the lower flange for exceptional stability and strength. Crossmembers are 140mm high and reinforced (for high floor load capacity). Additional reinforcement via gusset plate in the front lower flange/vehicle frame area. Chassis from galvanized steel up to the support structure. Axles and Suspension: Disc brakes 22.5, Jost (DCA) axle assemblies, 3x9 ton with DCA air suspension, lifting and lowering functions, Wabco Smartboard info center, electronic brake wear indicator BVA readable in the tractor unit (display). First axle with traction assist (new EC regulation, without tractor unit installation). Optionally, first and third axles liftable as per MP request. Tyres and Wheels: 6 wheels with tires, size 385/65 R 22.5 as per manufacturer's choice (Br-Go-Co), on silver steel rims, size 11.75x22.5 ET 120. King Pin: 2" bolted into a 10mm thick plate. Landing Legs: Mechanical landing gears with two speeds, 2x 20-ton support load, swing foot. Hjdofi Nmwspfx Afgsi Brake System: According to E.C. norms, EBS electronic system by Wabco with RSS (Roll Stability Support) and premium modulator. Spring-loaded brake system acting on two axles, controlled from the rear, ALU air reservoir system. Electrical System: According to EC Norm 91/633 and 97/28 with two five-chamber rear lamps, Aspöck Europoint type, integrated in ALU rear closure, 24V system with 1x 15-pin and 2x 7-pin sockets. LED side marker lights, two reflective plates at the rear, front position lights (2x white), rear position lights (2x red), two separate halogen reversing lights integrated in underrun protection. Superstructure/Body: Interior fully welded. Reinforced side walls, front wall load 17,250 daN, side and rear wall 13,400/10,400 daN. Aluminium tipper body, side walls of 30mm thick ALU plank profiles (2-3mm), 600mm wide, fully welded with upper and lower flange. Plank profiles fully welded inside. Floor with moving floor system laid on 140mm ALU crossmembers, forklift load approx. 9 t/m2. Crossmembers at approx. 350mm spacing for dense mounting. Special ALU corner profiles in chiseled design. Smooth rear wall, straight design, with two ALU swing doors, 50/30mm thick, with two rod locks mounted in a welded-in ALU rear frame with Teflon and stainless-steel bearings. Doors secured in opened position with lateral chains. Hard wear plates on side walls (approx. 2000x1500x4mm), fully welded. Mobile residual discharge wall with Kevlar tarpaulin, approx. 1800mm long plus lateral brushes with Kevlar seal. Service door in front wall with inward-turning ladder. Hydraulic System: Moving floor system in the floor with hydraulically operated ALU profiles on ALU square profiles with approx. 880 PE-HD sliding elements and additional anti-lifting slide bearings, Type CF 10mm floor version. Hydraulic stroke approx. 200mm. Fixed ends at the front wall. Separate hydraulic connection possibility under the vehicle with fixed halves, pipe size NW 21. Fixing half with size and design to be specified. Operating pressure 190-max. 240 Bar. ALU end sections welded into the moving floor. Electric control rear left with remote integrated in lockable watertight box. Without hydraulic hoses. Accessories: 6 PVC mudguards with 2 anti-spray flaps, 6 PVC splash guards above the wheels, 1 ALU spare wheel holder, foldable side ALU underrun protection, one toolbox approx. 860x460x400

Durumu: kullanılmış, azami yük ağırlığı: 28.150 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 11/2019, yükleme alanı hacmi: 92 m³, Üretim yılı: 2019, Donanım: ABS, * Stas 3-axle walking floor S300ZX * 10 mm floor * approx. 92 m³ load volume * Remote control * Rolling tarpaulin * Air suspension Hjdpfjw H Hprex Afgei * Two lift axles * Disc brakes * JOST axles * EBS * ABS

Durumu: kullanılmış, azami yük ağırlığı: 33.320 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2016, yükleme alanı uzunluğu: 13.530 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.780 mm, yükleme alanı hacmi: 92 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.977 mm, Donanım: ABS, STAS hareketli taban +/- 92 m3, 21 adet 10 mm'lik tahtadan oluşan kargo tabanı, hidrolik. Bagaj kapağı, hidrolik kaput, sürgülü zemin altında arkada paslanmaz çelik aşınma plakası, içeri/dışarı itme fonksiyonu, kablolu uzaktan kumanda, yükleme basınç göstergesi, bölmede servis kapısı, gövdenin ön tarafında erişim ve ayakta durma alanı, çalışma lambaları, ABS, EBS, SAF Intra CD aks(lar), disk fren sistemi, alüminyum düşme ayakları, hava süspansiyonu, Wabco SmartBoard, araç reklamla kaplanabilir ve/veya etiketlenebilir Teklifimiz genellikle yeni bir TÜV onayı olmaksızın yapılır. Yeni bir TÜV muayenesine ihtiyacınız varsa, ortak atölyelerimizden bir teklif sunmaktan mutluluk duyarız! Araç reklam ve/veya etiketlerle kaplanabilir. Teslimat ve ödeme konusunda genel şartlarımız geçerlidir. Bu mülk için size finansman veya kiralama teklifi sunmaktan mutluluk duyarız. Hedpfxswcilns Afgsi Lütfen bizimle iletişime geçin!

Durumu: kullanılmış, azami yük ağırlığı: 31.800 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2015, bir sonraki muayene (TÜV): 02/2026, yükleme alanı hacmi: 92 m³, Üretim yılı: 2015, Donanım: ABS,

Durumu: yeni, azami yük ağırlığı: 30.050 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.664 mm, yükleme alanı genişliği: 2.475 mm, yükleme alanı yüksekliği: 2.165 mm, yükleme alanı hacmi: 52 m³, Üretim yılı: 2025, Braking System: * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring brake cylinders * Disc brakes * Brake pad wear indicator (not connected) Axles: * 3 x 9 t SAF axles * 1st and 3rd axles are automatic lift axles, controlled via the EBS-E system Suspension: * Air suspension with raise/lower system (automatic lowering during tipping—can be manually locked via SmartBoard—as well as via switch on the chassis) Electrical / Lighting: * Tire pressure monitoring system (Wabco Trailerpulse) * Wabco SmartBoard * Starting aid is activated via button in the truck—without truck-side installation—as well as by pressing the brake pedal three times * 2 x 7-pin and 1 x 15-pin sockets * Aspöck LED lighting * 2 LED reversing lights (switched via reverse gear) * 1 LED work light on each side near the landing legs General Attachments: * Aluminum air tanks * Weweler crank landing gear * Side underrun protection * Foldable underrun guard with handle * Speedline Diamond aluminum rims * 1 x plastic toolbox on the left (approx. 860 x 520 x 500 mm) * Air pressure gun with 16 m hose reel in the toolbox * Closed plastic individual mudguards * 1 dust bag incl. bracket on the right side * 3 m aluminum access ladder stored on the right above the mudguards * Shovel and broom holder on the left above the mudguards * Loading pressure gauge mounted at the front of the chassis * Access steps and standing platform mounted at the front of the frame Chassis: * Aluminum chassis frame Tipping Body: * Aluminum rear tipper body—rectangular—with smooth side walls * Hyva hydraulic ram, 250 bar * Straight 4 mm aluminum front wall * Access steps on the inside left front wall of the body * Smooth inner and outer sidewalls * Double-walled 600 mm side wall profiles—30 mm thick—3 mm inside, 2 mm outside * Side wall profiles are continuously welded on the inside; 90° corners formed by right-angled profile between floor and side walls, enabling full utilization of loading width * Top rail 90 mm wide Hsdpfx Afswgg Uzogoi * 6 mm wear-resistant aluminum floor, 110 Brinell quality * Combination double-wing rear doors—straight mounted with double hinges and reinforcement profiles, each with a grain chute and all-round rubber seal * When open, doors are secured with chains, allowing them to rest almost flush against side walls * 4-point door locking hooks at the bottom, automatically released during tipping—can be pneumatically locked via lever on the frame Rollcover: * Rollcover—RAL 9005 deep black—with 3 side tensioning straps * Trapezoidal tarpaulin support, 150 mm high, at front wall and rear flap Loading Volume: * Loading volume: 51.8 m³ Fifth Wheel Height: * Fifth wheel height: 1,150 mm Information: * Body and chassis painted with acrylic paint in RAL 9005 deep black * --Technically permissible gross weight of 39,000 kg-- * New vehicle, unregistered, full manufacturer’s warranty * Errors and prior sale reserved Delivery Time: * Immediately available ex Egestorf

Durumu: kullanılmış, azami yük ağırlığı: 29.950 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2020, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 9.502 mm, yükleme alanı genişliği: 2.472 mm, yükleme alanı yüksekliği: 2.266 mm, yükleme alanı hacmi: 53 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.838 mm, Üretim yılı: 2020, Donanım: ABS, * Aluminium box tipper body with aluminum chassis * 1st axle liftable * 3rd axle steered & lockable * Wabco trailer EBS, ABS, ALR & EBS-E system * Wabco Optilevel electronic air suspension * Wabco SmartBoard unit * CRAMARO electric sliding tarpaulin roof with remote control * SAF INTRA CD axles with disc brake system * Tipper lowering on/off switch * Hyva hydraulic system ----* Rear combination door: double-wing swing door with swivel rod lock / pendulum flap * Pneumatic tailgate locking * 2 x grain sluices with cover ----* LED side marker reflectors * Work lights * Toolbox * Ladder & rear underrun protection * Wheel chocks * Tow coupling * Light metal rims ----* Tire dimensions: 385/65R22.5 160J * Technical gross weight: 39,000 kg * Curb weight: 6,050 kg * Total length: 10,777 mm * Safety inspection due: 04/2026 ----Vehicle number: 11752----Subject to errors and prior sale----Advertising and various lettering digitally removed.-----We are happy to assist you with all formalities involved in purchasing a vehicle. Simply let us know your requirements and suggestions—we will take care of them. Among other services, we can offer the following for an additional fee:----* Trade-in of your old vehicle * TÜV/Safety inspection certification * Complete export processing * Financing brokerage * Application for export license plates * Vehicle delivery/transfer * Vehicle registration * Recovery and vehicle transport ----YOUR VTS TEAM Hjdoygb U Ispfx Afgji

Durumu: kullanılmış, boş ağırlık: 7.590 kg, azami yük ağırlığı: 28.410 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2021, yükleme alanı hacmi: 92 m³, süspansiyon: hava, lastik boyutu: 385/65 R22,5, Donanım: ABS, | STAS Moving Floor Trailer | Model S300ZX, grain hopper, remote control | 7mm floor, extreme Durabright finish | Toolbox with air hose, 2 lifting axles | Air suspension, spare wheel holder | Unladen weight: 7,590 kg, payload: 28,410 kg | Tyres: 385/65 R22.5 | Jost axles with disc brakes Seller: Christopher Glock German/English Mobile: (Whatsapp) Email: christopher. Full stock available at: Hofgasse 25, A-4063 Hörsching | Errors, omissions, and prior sale reserved. | Sale to trade customers only. Hedpfx Afowqqy Aegei

Durumu: kullanılmış, azami yük ağırlığı: 32.550 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 08/2016, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.350 mm, yükleme alanı yüksekliği: 1.500 mm, yükleme alanı hacmi: 30 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.350 mm, Donanım: ABS, Stas S300CX İlk tescil: 25-08-2016 Alüminyum şasi/çelik kasa SAF akslar, disk frenli, ABS ve EBS'li Havalı süspansiyon Smartboard Seri numarası: YE6S300CXG0001112 Lastikler: 385/65 R22,5 %35 Hedpfeyf Sf Usx Afgji Toplam ağırlık: 39.000 kg, Boş ağırlık: 6.450 kg, Yük kapasitesi: 32.550 kg Katlanabilir arka alt koruma Kasa: U-8,50 m, G-2,35 m, Y-1,50 m = 30 m³ ADR onayı için üretilmiştir Hatalar, yazım yanlışları ve ara satış hakkı saklıdır.

Durumu: kullanılmış, boş ağırlık: 9.757 kg, azami yük ağırlığı: 32.243 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2025, bir sonraki muayene (TÜV): 10/2026, yükleme alanı uzunluğu: 13.127 mm, yükleme alanı genişliği: 2.325 mm, yükleme alanı yüksekliği: 2.755 mm, toplam uzunluk: 25.500 mm, toplam genişlik: 39.570 mm, toplam yükseklik: 138.420 mm, süspansiyon: hava, lastik boyutu: 385/55 R 22.5, Üretim yılı: 2025, ön lastik ölçüsü: 385/55 R 22.5, arka lastik boyutu: 385/55 R 22.5, emisyon sınıfı: hiçbiri, Donanım: ABS, ABS, aks üreticisi SAF, renk siyah, havalı süspansiyon ve kaldırma, tahıl boşaltma kapağı, kaldırma ve indirme, damper gövdeli, 1. ve 3. aks kaldırılabilir, brandalı mekanik üstü, frenler disk fren, yan koruma sabit, çelik yapı, 1 adet alet sandığı, katlanabilir arka koruma, duomatik, yük manometresi, 2x7 + 15 pinli elektrik bağlantıları, çalışma platformu, Wabco Smartboard, yanlarda LED çalışma farları, pnömatik son kilitleme, pnömatik katlanabilir arka koruma, devirmede otomatik alçaltma, Alcoa dura bright, tekli çamurluklar, süpürge ve kürek tutucu, 2x LED geri vites lambası, alüminyum merdiven. Hsdpfx Afjydfvqegei

Durumu: kullanılmış, azami yük ağırlığı: 27.500 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 06/2023, bir sonraki muayene (TÜV): 06/2025, yükleme alanı hacmi: 100 m³, Üretim yılı: 2023, Donanım: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length Silver-grey BIOSTAR – STEERING AXLE – V14900 – VERTICAL FRONT WALL – VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg Fifth wheel height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS FIFTH WHEEL HEIGHT: Accurate fifth wheel height is 1,150 mm. AXLES Tridem: Brand: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: large disc Offset: ET 120 BVA: with The first axle is an automatic lift axle controlled via the EBS-E system. The third axle is a self-steering trailing axle. CONNECTION BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: No lift axle. With traction aid. TRACTION AID: The traction aid is activated by pressing a button in the truck (truck equipment not included). AIR SUSPENSION: Lifting and lowering equipment. Aluminium air tank. STEERING AXLE LOCK: The self-steering trailing axle is locked as follows: – via the reversing lights – via a button in the truck (truck equipment not included) TYRES: 6 x 385/65 R 22.5 regional transport tyres (manufacturer’s choice) on ALCOA MATT aluminium rims. ET 120. BRAKING SYSTEM – EBS: WABCO EBS-E 2S/2M system – PREMIUM MODULATOR 2-line compressed air braking system according to CE guidelines. Spring-loaded parking brake acting on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING – ASPÖCK 24 Volt electrical system. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED side marker lighting mounted to the trailer. Without rear junction box – NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is mounted in the fixed aluminium under-run guard. With foldable aluminium lighting guard. 2 x 1 five-chamber rear lights – EUROPOINT III – LED version. HYDRAULIC CONNECTION: Connection at the front wall. With additional connection possibility below the body in front of the landing legs. ACCESSORIES REAR EXTENDABLE LADDER: Extendable ladder integrated at the rear of the vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminium spare wheel holder 2. BODY FRONT WALL: The front wall is made of robust aluminium plank profiles. INNER FRONT WALL TO FLOOR SEAL: Fixed seal between the floor and front wall using aluminium profile and PVC sealing. SIDE WALLS: Side walls smooth inside and out. Double-wall profiles, 600 mm wide – 30 mm thick – 3 mm inside, 2 mm outside (grain version). The side wall profiles are welded continuously on the inside. WEAR PLATE: Rectangular aluminium wear plate, inside rear, 2,000 (L) x 1,500 (H) x 4 mm. Hodpfxsxplxzo Afgji MOVING FLOOR SYSTEM: Cargo Floor CF 500 SL-C E-control. 21-board floor system. Drive segment consisting of 3 double-acting hydraulic cylinders with a stroke of 200 mm. Rear closure plate made of stainless steel. FLOOR SYSTEM CONTROL: E-control – Electric with radio remote control (original Cargo Floor). Load – stop – unload via switch. Manual emergency operation using unique red Cargo turn knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floorboards. FLOORBOARDS: 21 aluminium floor boards – 8 mm ribbed with welded aluminium end caps. REAR DOOR: 2 portal hinged...

Durumu: yeni, azami yük ağırlığı: 28.460 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 2.820 mm, yükleme alanı hacmi: 91 m³, Donanım: ABS, New vehicle! Available for purchase, rental, or lease with purchase option upon agreement! Hedpfx Afewi D S Asgoi STAS 91m³ Moving Floor / 10mm Ribbed Floor ---- * Manufacturer: Stas * Model: BIOSTAR - Moving Floor * First registration: - (New vehicle) * Colour: Body Black RAL 9005, Chassis Black RAL 9005, Tarp Black * Volume: approx. 91m³ (13.5m long x 2.47m wide x 2.82m high) * Gross weight: 36,000 kg * Unladen weight (manufacturer's data): 7,690 kg * Payload: 28,460 kg * Axles: 3x JOST axles / 1st axle liftable / starting aid / disc brakes * Tyres: 385/65 R22.5 on Speedline Diamond aluminium rims * Suspension: Air suspension with lifting and lowering function * EBS * Cargo Floor CF500SL-C with radio remote control * 10 mm ribbed floor * Moving bulkhead * Connection points at the front wall (additional connection points at landing legs) * Operator’s platform with access at front left * Swing doors (50/50) with pneumatic locking * Retractable step ladder on right * Roll tarp with tensioning straps * 3x crossbeams * Toolbox at rear right * Aluminium drop supports * Aluminium ladder approx. 3.80 m * Aluminium rear impact protection * Shovel and broom holder left * Smartboard at rear left * One-piece mudguard for rear lighting * 2x LED work lights (1x left, 1x right) * 2x LED reversing lights, rear left and right New vehicle – Immediately available! Available for purchase, rental, or lease with purchase option upon agreement! Notice regarding possible errors in the listing: Despite the careful preparation of this listing, errors in text or details may occur. We accept no liability for mistakes, amendments or interim sales. All information is provided without guarantee. Please contact us to verify details or clarify any further questions.

Durumu: yeni, azami yük ağırlığı: 28.240 kg, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.820 mm, yükleme alanı hacmi: 91 m³, Donanım: ABS, Stock no. 5559 New vehicle in stock – available immediately! Purchase, rental, or rent with a purchase option upon request! Side tarpaulin retrofit available for an additional charge! Stas 91 m² moving floor / 10 mm flat floor / TÜV load certificate ---- * Manufacturer: Stas * Model: BIOSTAR – Walking Floor trailer * First registration: – (New vehicle) * Color: Galvanized chassis, body in RAL 7016 silver grey, tarpaulin SIO 7340 * Volume: approx. 91m³ (13.50m long x 2.475m wide x 2.64m to 2.82m high) * Gross weight: 36,000 kg * Unladen weight (according to registration): 7,760 kg * Payload: 28,240 kg * Axles: 3x SAF axles / 1st axle liftable / starting aid / disc brakes * Tires: 385/65 R22.5 new on Speedline Diamond aluminium rims * Wheelbase: 7.85 m * Suspension: ECAS air suspension with raise and lower function * ABS / EBS * Cargo Floor CF 500 SL-C with remote control and control box rear left * 21 flat floor boards, 10 mm * 12 pairs of retractable lashing rings in the floor * Welded aluminium end caps * Complete emptying partition with brushes and stainless steel handles * Service door in front wall * Swing doors (50/50) with pneumatic locking Hedpfxev Emk Us Afgei * 2x locking bars * Swivelling rear cross member at door closure * Hydraulic connections at the front with 3 m hoses and * Connection possibility beneath the body without hoses * Operator platform with ladder front left * Fifth wheel height: 1,150 mm * Single mudguards * Full load landing legs * Rear aluminium underride guard (one piece, foldable) * Rolling tarpaulin (900g/m²) with tensioning straps * Steel roof bows, foldable and longitudinal lashing straps * 1x tool box rear left * 1x aluminium ladder, 3.80 m long * Load pressure gauge * Smartboard * TPMS tire pressure monitoring system * Aluminium rear buffer * 1x extendable ladder at the rear right * 2x LED work lights in front of axles * 2x LED reversing lights at the rear * 1x LED work light inside front wall * 2 x 3 function lights in upper rear door cross beam New vehicle in stock – available immediately! Purchase, rental, or rent with purchase option upon request! Note regarding possible errors in the ad: Despite careful preparation, occasional errors in text or specifications cannot be ruled out. We accept no liability for mistakes, changes, or prior sale. All information provided without guarantee. Please contact us to verify details or for further questions.

Durumu: kullanılmış, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2015, yükleme alanı hacmi: 50 m³, Üretim yılı: 2015, Donanım: ABS, 23.500 EUR net, disk frenler, coil havuzu, alüminyum-alüminyum, evrensel kapılar, büyük kapılar, brandalı, Belçika tescilli Hsdpfxsyd Ab Ro Afgoi

Durumu: kullanılmış, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2023, Üretim yılı: 2023, Donanım: ABS, Visit our website, where you can find our complete vehicle inventory with many more photos and detailed information in multiple languages. SEL 8345 STAS S300ZX 2 lift axles German registration / 1 owner First registered: 06.02.2023 Year of manufacture: 2023 Gross vehicle weight (kg): 42,000 Permitted gross weight (kg): 42,000 Empty weight (kg): 7,990 VIN: YE6S300ZXN0008 Main inspection (HU): 02.2026 Hsdpex Sbidofx Afgsi TIRES AND AXLES: Tires: 385/65 R 22.5 Axle configuration: 3 axles, Jost 1st and 3rd axle: liftable Air suspension Disc brakes BODY: Internal dimensions: Height (m): 2.83 (2.71) Width (m): 2.48 Length (m): 13.50 OTHER SPECIFICATIONS: Portal doors VEHICLE DOCUMENTS: Registration certificate part I Registration certificate part II COC (Certificate of Conformity) M. BUFANO (Italiano, English, Deutsch) J. CORDEIRO (Português, Español, Italiano, English) J. MARJANOVIC (Deutsch, Bosnian) L. OBODYNSKA (Ukrainian, Russian) We speak: GERMAN, ENGLISH, ITALIAN, SPANISH, PORTUGUESE, UKRAINIAN, RUSSIAN, POLISH, BOSNIAN While every effort has been made to ensure the accuracy of the information, we cannot be held liable for any errors or omissions. We ask our customers to consult the available photos. All measurements are approximate values. Our vehicles are sold in their current condition (as is). We invite customers to visit our premises to inspect the vehicle in person. Test drives are also possible. Please note that the batteries included are those currently installed. If the customer would like new batteries, we are happy to provide a quote.

Durumu: kullanılmış, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2023, Üretim yılı: 2023, Donanım: ABS, Besuchen Sie unsere Webseite, auf der Sie unseren vollständigen Fahrzeugbestand mit vielen weiteren Fotos und Informationen in mehreren Sprachen finden. SEL 8344 STAS S300ZX 2 Liftachsen Hjdsx Sbh Tjpfx Afgsi deutsche Zulassung / 1. Hand Erstzulassung: 06.02.2023 Baujahr: 2023 Technisch zulässiges Gesamtgewicht (kg): 42.000 Zulässiges Gesamtgewicht (kg): 42.000 Leergewicht (kg): 7.990 FIN: YE6S300ZXN0001770 BEREIFUNG UND ACHSEN: Bereifung: 385/65 R 22,5 Achskonfiguration: 3 Achsen Jost 1. und 3. Achse liftbar Luftfederung Scheibenbremse AUFBAU Innenmaße: Höhe (m): 2,69 Breite (m): 2,48 Länge (m): 13,50 SONSTIGE AUSSTATTUNG: Portaltüren FAHRZEUGUNTERLAGEN: Zulassungsbescheinigung Teil I (Schein) Zulassungsbescheinigung Teil II (Brief) COC M. BUFANO m. (Italienisch, Englisch, Deutsch) J. CORDEIRO j. (Portugiesisch, Spanisch, Italienisch, Englisch) J. MARJANOVIC j. (Deutsch, Bosnisch) L. OBODYNSKA Ukrainisch/?????, Russisch/??-?????) Wir sprechen: DEUTSCH, ENGLISCH, ITALIENISCH, SPANISCH, PORTUGIESISCH, UKRAINISCH, RUSSISCH, POLNISCH, BOSNISCH Obwohl alle Anstrengungen unternommen wurden, um die Richtigkeit der Informationen zu gewährleisten, übernehmen wir keine Haftung für Fehler oder Auslassungen. Wir bitten unsere Kunden, die bereitgestellten Fotos zu beachten. Die angegebenen Maße sind Circa-Werte. Unsere Fahrzeuge werden im gegenwärtigen Zustand verkauft. Wir laden unsere Kunden ein, unser Unternehmen zu besuchen, um den Zustand des Fahrzeugs persönlich zu überprüfen. Außerdem bieten wir die Möglichkeit zu einer Probefahrt. Bitte beachten Sie, dass die mit dem Fahrzeug gelieferten Batterien die aktuell verbauten sind. Sollten Sie neue Batterien wünschen, können wir Ihnen ein Preisangebot unterbreiten.

Durumu: kullanılmış, toplam ağırlık: 36.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2019, * Kaldırma aksı * ALU jantlar * JOST akslar * Rulo branda * Boş ağırlık: 7.760 kg -----Dahili araç numarası: 10296----Hatalar ve ara satış hakkı saklıdır Hsdpfx Aow Rit Tjfgei WhatsApp desteği mevcut! Araçla ilgili sorularınız veya daha fazla bilgi için bizimle WhatsApp üzerinden kolayca iletişime geçebilirsiniz

Durumu: kullanılmış, azami yük ağırlığı: 33.370 kg, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2014, yükleme alanı uzunluğu: 8.500 mm, yükleme alanı genişliği: 2.350 mm, yükleme alanı yüksekliği: 1.500 mm, yükleme alanı hacmi: 30 m³, toplam genişlik: 2.550 mm, toplam yükseklik: 3.160 mm, Donanım: ABS, Stas S300CX İzoleli asfalt damperli dorse İlk tescil MB akslar, disk frenli, ABS ve EBS'li Havalı süspansiyon Smartboard Şasi numarası: YE6S300CXD0001049 Lastik: 385/65 R22,5 %35 Toplam ağırlık: 39.000 kg, Boş ağırlık: 5.630 kg, Yük kapasitesi: 33.370 kg Çalışma platformu Branda (rulo tip) 3x tahıl sürgüsü Katlanabilir yan alt koruma Kasa: U-8,50 m, G-2,35 m, Y-1,50 m = 30 m³ Hedpfxjx Txmio Afgsi ADR onayı için üretildi Hatalar, yazım yanlışları ve ara satış hakkı saklıdır.