Kullanılmış Faymonville Çalışma Platformu satın al (206)

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 10.700 kg, azami yük ağırlığı: 38.800 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 235/75 r 17,5, Donanım: ABS, Gooseneck: • Gooseneck with front corners chamfered at 45° and rear chamfer approx. 750 mm x 10° • 3 pairs of lashing rings • 30 mm thick hardwood floor Extendable loading platform: • Loading platform in extendable design with rear chamfer approx. 1,000 mm x 8° • Cut-outs in the outer frame of the loading platform for securing straps • Approx. 48 mm thick hardwood covering, checker plate covering over the axles Two-part steel ramps: • One pair of galvanized, two-part steel ramps with approx. 48 mm thick hardwood covering • Ramp sections fold in and out hydraulically, with hydraulic lifting system and hydraulic lateral adjustment • Maximum load per pair: approx. 40,000 kg Axles and tires: • BPW axles and suspension, 2 rigid axles, 1 self-steering axle • Technical axle load: 12,000 kg • Electromagnetic reversing lock, activation via reverse gear and manual operation • Air suspension with lift and lower valve • Axle tools • 235/75 R 17.5 3PMSF Braking system: • WABCO braking system according to EU regulations with EBS-E Painting: Dodpfx Ashlz S Nef Teku • First-class and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component zinc-rich primer • High-quality 2-component top coat, single color in MB 7350 Novagrey • Rear section metallized and painted in RAL 9010 Landing legs: • JOST landing legs with 2-speed gearbox for 24t lift capacity (50t test load) Steel construction: • Steel construction made of high-strength fine grain steels • Steel grades: • S355J2+N/S355MC • S690QL/S700MC Electrical system: • Electrical system according to EU requirements, 24 Volt lighting • ASPÖCK UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets Included accessories: • One spare wheel with holder • One galvanized steel headboard approx. 400 mm high • Yellow-red air couplings on the galvanized connection panel at the front • 4 wheel chocks • Bracket for rotating beacon at the rear of the trailer • Holder at rear of gooseneck for ALU approach ramps • Galvanized folding supports under the rear chamfer of the loading platform • Cover plates for bridging the gap between ramps and loading platform • White reflector tape to EU specifications on the sides, extension, and red at rear • Electro-hydraulic unit mounted at the rear, under the loading platform • On both sides of the gooseneck and ramps, holders for warning panels with socket • Control valves for the ramps mounted on the right trailer side • ALU sideboards and tailboard on the gooseneck approx. 2,440 x 400 mm • Rear, galvanized removable stakes (body length approx. 2,560 mm) • Four approx. 400 mm extendable warning boards with position light • 3 pairs of WADER container locks in deck for 20ft, 30ft, or 40ft container • 6 pairs of stake pockets (100x50 mm) in the outer frame of the loading platform • Galvanized extensions, extendable by approx. 230 mm per side • 20 x 20 mm square climbing strips every 200 mm on the outer frame of the rear chamfer of the loading platform • Anti-slip sand coating on checker plate surfaces above kingpin and loading platform • Load pressure gauge for axle load measurement including load chart • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) and hot finished.

Durumu: kullanılmış, dingil konfigürasyonu: 3 aks, dingil mesafesi: 14.560 mm, ilk tescil: 03/2016, süspansiyon: hidrolik, renk: yeşil, lastik boyutu: 285/70R19.5, Üretim yılı: 2016, Donanım: ABS, Belgische Zulassung. Pendelachse. Breite Warntafeln. Verbreiterungen. Ladefläche: Länge: 685 cm + 425 cm. Breite: 274 / 320 cm. Höhe: 45 cm. Funkferngesteuerte Lenkung. Ansteuerung über Hydraulik des Zugfahrzeugs. Maximales technisches Gesamtgewicht: 81.500 kg. Eigengewicht: 24.470 kg. = Weitere Informationen = Achskonfiguration Reifenmaß: 285/70R19.5 Bremsen: Trommelbremsen Federung: Hydraulische Federung Vorderachse 1: Zwillingsbereifung; gelenkt; Reifenprofil links innen: 30%; Reifenprofil links außen: 30%; Reifenprofil rechts innen: 30%; Reifenprofil rechts außen: 30% Hinterachse 1: Zwillingsbereifung; gelenkt; Reifenprofil links innen: 60%; Reifenprofil links außen: 60%; Reifenprofil rechts innen: 60%; Reifenprofil rechts außen: 60% Hinterachse 2: Zwillingsbereifung; gelenkt; Reifenprofil links innen: 50%; Reifenprofil links außen: 40%; Reifenprofil rechts innen: 40%; Reifenprofil rechts außen: 60% Dsdpfjwyiqlex Af Toku Vorderachse 2: Zwillingsbereifung; gelenkt; Reifenprofil links innen: 60%; Reifenprofil links außen: 60%; Reifenprofil rechts innen: 60%; Reifenprofil rechts außen: 60% Maße Abmessungen (L x B x H): 1.626 x 275 x 378 cm Gewichte Leergewicht: 24.470 kg Nutzlast: 57.030 kg Zulässiges Gesamtgewicht: 81.500 kg Wartung Hauptuntersuchung (APK): geprüft bis 12.2025 Finanzielle Informationen Preis: auf Anfrage Identifikation Typennummer: GigaMax STBZ-4VA 1+3 PENDEL / EX = Firmeninformationen = ALLE PREISE SIND NETTO FÜR DEN EXPORT. Joris Versteijnen (NL-DE-EN), Wouter Greutink (NL-DE-EN-ES-IT), Govorim po russki. Wir bemühen uns nach Kräften, korrekte Informationen zu liefern, jedoch können aus den eingestellten Texten keine Rechte abgeleitet werden.

Durumu: mükemmel (kullanılmış), ilk tescil: 10/2021, Üretim yılı: 2021, = Further Information = Unladen weight: 700 kg Payload: 50,000 kg Gross vehicle weight: 60,800 kg Extendable body: Yes Technical condition: very good Visual condition: very good Please contact Sales for further information. = Company Information = If you have any questions or suggestions, don't hesitate to contact us. We guarantee a response within 8 hours. Prices are exclusive of VAT. No rights can be derived from the given information. Office Phone: MOB: Nederlands - English - Deutsch - Français - Español - Italiano (Available on WhatsApp and Viber). MOB: Nederlands (Available on WhatsApp and Viber). Djdswyn U Aopfx Af Teku When paying by bank transfer, funds must be transferred to our bank account as stated below. Always check the payment details provided on our website. If you receive different information, please contact us immediately. If you have any doubts, call us so we can verify the invoice and/or payment. Bank details: Rabobank Laan van Limburg 2 4701BP Roosendaal IBAN: NL 89 RABO EORI/VAT/TAX: NL857401B(01) BIC/SWIFT: RABONL2U

Durumu: kullanılmış, toplam ağırlık: 38.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 9.200 mm, yükleme alanı genişliği: 2.500 mm, ilk tescil: 07/2005, * Extendable * Dead weight: 8,900 kg Djdpfx Aowkn Htjf Tjku -----Internal vehicle number: 7283----Errors & prior sale excepted.

Durumu: kullanılmış, dingil konfigürasyonu: 3 aks, ilk tescil: 01/2020, süspansiyon: hava, renk: diğer, lastik boyutu: 235/75 R17.5, Üretim yılı: 2020, Donanım: ABS, Chassis Chassis height: 90 cm Kingpin / fifth wheel diameter: 2 inch Dkodpfx Afou H D Tas Tju Structure Deck height: 120 cm Special transport 2-piece road plates: ✓ Hydraulic ramps: ✓ Axle length: 90 cm Loading platform length: 930 cm Ramp length: 405 cm Gooseneck length: 430 cm Maximum width: 305 cm (20 cm + 20 cm) Max. length: 930 cm Extendable: ✓ Tank Fuel: ✓ = Additional Information = Axle configuration Tyre size: 235/75 R17.5 Axle brand: SAF Brakes: Drum brakes Suspension: Air suspension Axle 1: Twin tyres; lift axle; left outer tyre tread: 15%; right outer tyre tread: 80% Axle 2: Twin tyres; left outer tyre tread: 60%; right outer tyre tread: 50% Axle 3: Twin tyres; steered; left outer tyre tread: 70%; right outer tyre tread: 70% Axle 4: Twin tyres; steered; left outer tyre tread: 75%; right outer tyre tread: 65% Dimensions Dimensions (L x W x H): 1410 x 255 x 335 cm Weights Unladen weight: 11,480 kg Payload: 49,320 kg Gross vehicle weight: 60,800 kg Functional Body manufacturer: Faymonville Loading platform height: 90 cm Identification Registration number: C525073 Serial number: YAMT14XX5K0104637 = Company Information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Durumu: kullanılmış, toplam ağırlık: 66.500 kg, boş ağırlık: 20.320 kg, azami yük ağırlığı: 46.180 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 01/2004, lastik boyutu: -, Üretim yılı: 2004, ref: 2220 Extra-low 3-axle rear trailer + 1 front axle (Dolly) Maximum authorized weight: 66 t Removable gooseneck trailer Extendable trailer (by 5 m) Trailer with 3 forced steering axles (manual remote control) Trailer can operate with or without Dolly Dksdjwcrzrepfx Af Teu Total trailer length: 16.43 m + 5 m (extendable) Unladen weight: 20,320 kg + 2,520 kg for Dolly Gooseneck: L = 4.43 m Extra-low platform: L = 7.5 m + 5 m (extendable) Height: 0.5 m Trailer width: 2.74 m Platform above rear axles: L = 4.5 m H = 1.05 m Excavator arm recess Removable hydraulic rear ramps and hydraulic ramp displacement Trailer tires: 285/70R19.5 Dolly tires: 235/75R17.5 Serial numbers: YA9TL366B04113968+122B4113969

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 11.400 kg, azami yük ağırlığı: 36.600 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 235/75 r 17,5, Donanım: ABS, Gooseneck: • Gooseneck in SNT design for optimised loading platform length, approx. 3,700 mm long. • Rear gooseneck with chamfer approx. 1,000 mm x 6°. • Technical fifth wheel load: 18,000 kg • Suitable for tractor units: 4x2 or 6x2 Loading platform: • Loading platform, length approx. 9,400 mm, with rear chamfer approx. 900 mm x 6°. • Platform area after the gooseneck, hydraulically liftable and lowerable. • Platform section length approx. 3,000 mm, load capacity up to 9,000 kg Ramps: • 1 pair of two-part hydraulic steel ramps, approx. 4,350 x 900 mm • Hardwood surface • Hydraulically foldable ramp ends • Ramps can be shifted individually by approx. 235 mm outward and approx. 365 mm inward hydraulically Axles and Suspension: • BPW axles and suspension, two rigid axles, one steering trailing axle • Technical axle load: 12,000 kg • Electromagnetic reverse lock, activated via reverse gear and manually • Air suspension with lift and lower valve • Axle tools Tyres: • 235/75 R 17.5 3PMSF twin tyres • Load index 143/141J (144/144F) Braking system: • Brake system by WABCO EBS-E in accordance with EU regulations Lighting system: • 24-volt lighting system in "ASPÖCK-NORDIK full LED" (ASS 3) • Design in accordance with EU regulations Metal finishing: • Standard HRM metallisation (High Resistance Metallisation) of the outer frame • Entire steel structure shot-blasted, then defined visible areas finished • Metallised with ZINACOR 850 (85% Zinc – 15% Aluminium), hot galvanised finish Paintwork: • 6-coat final treatment: • Complete steel structure shot-blasted after welding • One coat of zinc-based primer, followed by an adhesion primer • Final coating with two layers of 2-component (acrylic) paint in solid novagrau colour, followed by cavity sealing with special wax. Rims in silver. Steel Construction: • Steel structure made of high-strength fine-grained steel • Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) • Welders certified to DIN EN 287-1 • MAG welding process according to EN ISO 4063 Dodpfx Afeiuy Npj Tsku • Shielding gas M21 according to EN ISO 14175 Accessories included: • Plug-in steel front wall, approx. 400 mm high • Connector panel for supply lines to tractor unit, mounted at height of outer frame profile • ASPÖCK-UNIBOX on front connector panel with 24N, 24S & 15-pin sockets - 24N connection according to ISO-1185 - 24S connection according to ISO 3731 - 15-pin connection according to ISO-12098 • 1 spare wheel with mounting adapter under the right side of the loading platform, in front of the axles • Parking position for warning plates on the gooseneck when not in use • Gooseneck outer beam with mounting holes for bolted lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) • One mounting hole on upper rear section of gooseneck outer beam for one bolted lashing ring. 1 pair of screw-in lashing rings included (LC 10,000 daN) • 1 pair recessed lashing rings rear centre of the gooseneck (LC 5,000 daN) • 3 pairs recessed lashing rings inside the outer gooseneck beam (LC 5,000 daN) • 3 pairs lashing rings in the centre of the gooseneck (LC 5,000 daN) • Approx. 40 mm hardwood floor above gooseneck • 2" king pin • On gooseneck, 1 pair plug-in aluminium side boards, approx. 400 mm high, anodised finish • On gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodised finish.

Durumu: mükemmel (kullanılmış), yükleme alanı uzunluğu: 20.180 mm, yükleme alanı genişliği: 3.000 mm, ilk tescil: 09/2015, Üretim yılı: 2015, = Further Information = Unladen weight: 13,600 kg Payload: 28,400 kg Gross vehicle weight: 42,000 kg Extendable body: Yes Technical condition: very good Visual condition: very good Damages: none Please contact Sales for further information. = Company Information = Dsdporywukefx Af Teku If you have any questions or suggestions, don't hesitate to contact us. We guarantee a response within 8 hours. Prices are exclusive of VAT. No rights can be derived from the given information. Office Phone: MOB: Dutch - English - German - French - Spanish - Italian (Available on WhatsApp and Viber). MOB: Dutch only (Available on WhatsApp and Viber). When making payment by bank transfer, funds must be transferred to our bank account listed below. Always verify the payment details provided on our website. If you have received other information, please contact us. If in doubt, please call us so we can verify the invoice and/or payment. Bank details: Rabobank Laan van Limburg 2 4701BP Roosendaal IBAN: NL 89 RABO EORI/VAT/TAX: NL857401B(01) BIC/SWIFT: RABONL2U

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 01/2019, süspansiyon: hava, renk: diğer, lastik boyutu: 235/75 R17.5, Üretim yılı: 2019, Donanım: ABS, Chassis Chassis height: 87 cm Kingpin / fifth wheel diameter: 2 inches Kingpin / drawbar height: 120 cm Special transport 2-piece road mats: ✓ Hydraulic ramps: ✓ Loading floor length: 930 cm Ramp length: 395 cm Dkodpou H D R Eofx Af Tsu Gooseneck length: 415 cm Low loader: ✓ Maximum width: 300 cm (25 cm per side) Maximum length: 1380 cm Extendable: ✓ Tank Fuel: ✓ = Further information = Axle configuration Tyre size: 235/75 R17.5 Axle make: Saf Brakes: Drum brakes Suspension: Air suspension Axle 1: Twin tyres; Left outer tyre tread: 60%; Right outer tyre tread: 60% Axle 2: Twin tyres; Left outer tyre tread: 20%; Right outer tyre tread: 30% Axle 3: Twin tyres; Steering; Left outer tyre tread: 55%; Right outer tyre tread: 50% Dimensions Dimensions (L x W x H): 1380 x 255 x 341 cm Weights Unladen weight: 10,040 kg Payload: 30,960 kg Gross vehicle weight: 41,000 kg Functional Body make: Faymonville Loading platform height: 87 cm Identification Registration number: C505325 Serial number: YAMT13XX6K0104043 = Company information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Durumu: yeni, toplam ağırlık: 60.800 kg, azami yük ağırlığı: 49.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 r 17.5, Donanım: ABS, Gooseneck: - Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable Loading Platform: - Loading platform in extendable design with rear taper approx. 1,000 mm x 8° - 5 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - c. 48 mm thick hardwood flooring, over the axles with checker plate covering Detachable Two-Part Ramps: - One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting unit and hydraulically adjustable - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles, two rigid axles, two steering trailing axles, air suspension, with drum brakes, with raise/lower function - The trailing steering axles can be locked electromagnetically via reverse gear or manually - Axle tools - Tyres: 235/75 R 17.5 Brake System: - Brake system according to EU regulations with EBS-E (4S3M) Steel Construction: - Steel construction made of high-tensile fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Djdpfx Afoh Etf Rs Tjku Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat finish in single-colour Novagrau Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front terminal strip with 24N, 24S & 15-pin sockets Accessories Included: - 2" king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings at the galvanized front terminal strip - 4 chocks with holder at the front wall - Mounting at the rear area of the gooseneck for ALU drive-on ramps - Galvanized folding supports under the taper of the loading platform - Bracket for a rotating beacon - Cover plates to bridge the gap between ramps and loading platform - White reflector tape to EU specification on the sides, red at rear and on extension - Electro-hydraulic power pack - On both sides of the gooseneck and ramps, mounting brackets for warning signs incl. socket outlet - Ramp control valves installed on the right trailer side - One mudguard at the rear of the trailer - Instruction manual and description on USB stick - ALU side walls and end wall, plug-in, on gooseneck approx. 2,440 x 400 mm - The rear galvanized plug-in posts are removable (length of structure approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, 2x 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Extensions, galvanized, extendable by approx. 230 mm per side - Lift axle on the front axle with control - Square climbing rails 20 x 20 mm - Central lubrication system BEKAMAX - F

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 10.300 kg, azami yük ağırlığı: 39.200 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17.5, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Loading area after the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear chamfer approx. 1,000 mm x 8° - Cut-outs in the outer frame of the loading area for securing tension straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, chequer plate flooring above the axles Two-part Steel Ramps: - One pair of galvanized, two-part steel ramps approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding and unfolding ramp sections, hydraulic lifting mechanism, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles, Suspension and Tyres: - BPW axles and suspension, 2 axles rigid, 1 axle trailing steer - Technical axle load: 12,000 kg - Electro-magnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lowering valve - Axle tools - Tyres 235/75 R 17.5 3PMSF - TPMS tyre pressure monitoring system according to ECE R 141 Included Accessories: - One spare wheel with holder in front of the bulkhead - 2" kingpin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized connection rail at the front - 4 wheel chocks - Galvanized folding supports under the chamfer of the loading area - One holder for a beacon at the rear of the trailer - Cover plates to bridge the gap between the ramps and the loading area - White reflective tape according to EU regulations on the sides of the trailer and red on the rear - Electro-hydraulic unit at the rear, under the loading area - Holder for warning signs left and right on the gooseneck and ramps, including socket - Control valves for the ramps located on the right side of the trailer - European reflective boards (red-yellow) at the rear of the trailer - Manual and description on USB stick - On the gooseneck, ALU drop-in side boards and rear wall approx. 2,440 x 400 mm - The rear, galvanized drop-in stakes are removable (length of superstructure approx. 2,560 mm) - An electric cable winch with radio remote control, approx. 5,400 kg lifting force, including 9.5 mm thick steel cable, 24 m long with cable guide roller Dkedpfx Asu Hp Hrof Tsu - Bolted 5t ring for running the winch cable on the gooseneck without pulley - 2 pairs of WADER container pockets in the loading area for one 20ft container - 6 pairs of stake pockets for drop-in stakes 100 x 50 mm in the outer frame of the loading area - Lift axle on the front axle controlled by TEBS E depending on the current axle load and load status - 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the central beam at the rear in the chamfer (LC 10,000 daN) - On the chequer plates on the gooseneck and the loading area, painted sand layer as slip resistance - BEKAMAX centralized lubrication system (Pico) with standard grease NLGI-2 and removable guard for the pump - Four warning boards extendable by approx. 400 mm, size approx. 423 x 423 mm - 80 km/h speed stickers at the rear and on both sides - Load gauge to determine axle loads, including load diagram - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot blasted, then defined visible surfaces hot-coated in metallization with ZINACOR 850 (85% zinc - 15% aluminium)

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 9.300 kg, azami yük ağırlığı: 38.700 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.200 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 385/65 R 22,5, Donanım: ABS, Loading Platform: • Loading platform in extendable design with pneumatically operated locking mechanism • Loading platform with approx. 30 mm thick wooden floor • 7 pairs of outward-folding lashing rings (LC 5,000 daN) • 3 pairs of outward-folding lashing rings (LC 10,000 daN) • Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydro-mechanically forced steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with raise/lower valve Djdpfx Aeiu Etrof Teku • Axle tools • Tyres: 385/65 R 22.5 • TPMS (Tyre Pressure Monitoring System) according to ECE R 141 Brake System: • WABCO brake system compliant with EU regulations, with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin • Connections according to ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Accessories Included: • Remote-controlled steering from front and rear via cable remote with push-button operation, including single-track monitoring of axles • 4 wheel chocks with holders mounted on the front wall • 2" kingpin • One galvanized steel front wall approx. 1,600 mm high • Yellow-red air couplings mounted on the galvanized front connection bar • White reflective tape according to EU regulations on the sides, at extension and at the rear of the trailer in red • European reflective plates (red-yellow) on the rear of the trailer • One mudflap at the rear of the trailer • Manual and description • Mounting bracket for a beacon at the rear of the trailer • Loading platform with approx. 30 mm thick wooden floor enclosed in omega profiles • 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform • 1 spare wheel holder under the right side of the loading platform in the direction of travel • Electro-hydraulic unit • On the gooseneck and rear apron left and right, each with a bracket for warning boards including socket • Painted sand layer for anti-slip protection on the main beam • 6 pairs of WADER container locks on the loading platform, for 1x20ft, 2x 20ft, or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container • 4 pairs of crosswise mounted stake pocket bars on the loading platform for plug-in stanchions 100 x 50 mm • Access ladder mounted on the right in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm in front under the loading platform on the left in the direction of travel • BEKAMAX central lubrication system (Pico) with removable pump guard • Lift axle on the front axle controlled by TEBS E depending on current axle load and loading condition • Wireless remote control for the rear steering in addition to the cable remote, with indicator lights on the receiver for single-track monitoring • Four extendable warning plates approx. 400 mm extension, size approx. 423 x 423 mm with position light • Bracket for beacon on the warning plates • 80 km/h speed stickers on the rear and both sides • Load pressure gauge to determine axle loads, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then the defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Durumu: yeni, toplam ağırlık: 61.000 kg, boş ağırlık: 17.500 kg, azami yük ağırlığı: 43.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.750 mm, yükleme alanı yüksekliği: 400 mm, renk: gri, lastik boyutu: 245/70 R 17.5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and removable - For tractor units: 6x4 or 8x4 Lowbed: - Lowbed with external beams, extendable version, “SUPER LOW” design, length approx. 7,550 mm - Lowbed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking - Supply lines routed protected inside the extendable beams and automatically adjust to the respective lowbed length Rear running gear: - Rear running gear with closed outer frame, chequer plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at rear - 2 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame Dsdeh Hm Thepfx Af Tjku Axles and tyres: - “PENDLE-AXLE”, all axles forced-steered by hydromechanics - Burst protection valve on axle compensation cylinder with automatic RESET feature - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres / 3PMSF Accessories included: - Prepared for mounting attachable container positions for 1x 20ft or 1x 40ft container on the outer beams - 2'' king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with bracket - At the galvanized front connection strip: yellow-red air couplings - 4 wheel chocks - Remote steering from front and rear by cable remote control with push buttons, including track alignment monitoring for the axles - Hydraulic couplings from gooseneck to lowbed with multi-coupling system instead of screw couplings - Electro-hydraulic unit - White reflector tape according to EU regulations on the sides, extension, and red at the rear - 2 wooden blocks 500x250x200 mm - European reflector plates (red-yellow) at the rear of the trailer - On the gooseneck and rear panel, left and right, one bracket each for warning panels including socket - Central lubrication system with 2 BEKAMAX (Pico) pumps for NLGI-2 standard grease - Load pressure gauge to determine axle loads, including load chart - On the gooseneck, plug-in ALU side and rear walls approx. 2,000 x 400 mm - The rear galvanized plug-in posts are removable (body length approx. 2,120 mm) - Separate air connection with air gun on the gooseneck - Duomatic air coupling from gooseneck to lowbed - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps to bridge the mountings of the lowbed - Four extendable warning signs approx. 423 x 423 mm, extendable by approx. 400 mm - Radio remote control for the steering in addition to the cable remote, with indicator lights on receiver for track monitoring - 6 pairs of threaded blocks between lashing rings under the top chord on the outer beam for mounting screwable RUD rings VLBG-4 - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Folding extensions, approx. 230 mm per side - Anti-slip sand layer painted on the loading platform - Dipper recess on the rear running gear closed at the front and rear with plug-in plates - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (Zinc 85% - Alu 15%)

Durumu: yeni, toplam ağırlık: 63.000 kg, boş ağırlık: 15.550 kg, azami yük ağırlığı: 47.450 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long - Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator bucket arm - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood flooring on the bevel of the loading platform Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide - Ramps with hardwood covering - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward Djdpek Aht Uofx Af Tsku - Square climbing strips 20 x 30 mm, at approx. 200 mm intervals on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, first axle steerable, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated automatically in reverse gear and manually - Air suspension with lift and lower valve - Tires: 235/75 R 17.5 twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS tire sensors installed in all wheels, including spare wheels Accessories included: - Detachable front wall, steel, approx. 400 mm high - 3kW electro-hydraulic power unit for operating hydraulic functions, except hydraulic cable winch - Parking bracket for warning signs on gooseneck when not in use - 1 spare wheel - On the gooseneck: 1 pair of detachable ALU side boards, approx. 400 mm high, anodized - On the gooseneck: one detachable ALU rear board, approx. 400 mm high, anodized - Over the gooseneck: approx. 40 mm thick hardwood covering, checker plate covering above king pin - 2'' king pin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with two-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Telescopic width extensions (galvanized) approx. 230 mm per side - Wheel recesses with square climbing strips - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering from front and rear via cable remote control, with single track axle monitoring - 1st axle with automatic lifting axle function - Central lubrication system with 1 pump, BEKAMAX brand - Wireless remote control for remote steering, in addition to cable remote, with 2 indicator lights on receiver for single track monitoring - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for beacon

Durumu: yeni, toplam ağırlık: 69.500 kg, boş ağırlık: 13.500 kg, azami yük ağırlığı: 51.500 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 r17.5, Donanım: ABS, Gooseneck: Gooseneck in SNT design for optimization of loading area length, length approx. 3,700 mm Gooseneck rear with bevel approx. 1,000 mm x 10° Djdpfx Afek Ahugj Teku Loading Area: Telescopic loading area, length approx. 8,800 mm, with rear incline approx. 500 mm x 10° Recess in the incline and extending into the loading area for accommodating the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected within the extendable beam and adjust to the respective loading area length Ramps: 1 pair of two-piece steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically adjusted individually approx. 235 mm outwards and 215 mm inwards Axles and Suspension: BPW axles and suspension, two fixed axles, two steering trailing axles Electromagnetic reverse lock activated via reverse gear and manually Air suspension with lifting and lowering valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO brake system, EBS-E according to EU regulations Lighting System: 24-volt lighting system, “ASPÖCK-NORDIK full LED” Metallization: Standard HRM metallization of the external frame Complete steel structure shot blasted, subsequently visible defined surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished Steel Structure: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified according to DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included accessories: Removable steel front wall, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 Round NATO socket on the front connection strip Cable for supplying the electro-hydraulic pump and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations (except for hydraulic winches) 1 spare wheel with mounting adapter External beams on the gooseneck with mounting holes for bolt-on lashing rings, first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included Mounting hole on the upper rear of the gooseneck external beam for a screw-on lashing ring 1 pair screw-in lashing rings Approx. 40 mm thick hardwood floor above gooseneck On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized On the gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodized 2" king pin Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 4 wheel chocks with holders Provision for aluminium approach ramps Mechanical landing gears with 2-speed gearbox and crank On the loading area, continuous hardwood floor approx. 50 mm thick, interrupted only between the axles Load area locking with conically welded positioning profiles every 250 mm including pre-tension plate Slotted holes at the front of the loading area for attachable and repositionable bridging plates 1 intermediate table with recessed loading area, approx. 300 mm wide, for the large cross-section sliding tube with sheet metal covering Front and rear with longe...

Durumu: yeni, toplam ağırlık: 49.500 kg, azami yük ağırlığı: 38.800 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5 3PMSF, Donanım: ABS, Gooseneck: - Gooseneck with front corners chamfered at 45° and rear bevel approximately 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) Djdpfxouqlmns Af Tjku - 30 mm thick hardwood flooring Extendable Loading Platform: - Extendable loading platform with rear bevel approximately 1,000 mm x 8° - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - 1 pair of horizontal lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for securing straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring, over-axle areas with checker plate Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-tracking axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated via reverse gear or manually - Air suspension with raise/lower valve - Axle tools - 235/75 R 17.5 3PMSF Brake System: - WABCO braking system complying with EU regulations, with EBS-E (2S2M) Landing Legs: - JOST mechanical landing legs with 2-speed gearbox, 24 t lifting capacity (50 t test load) Accessories Included: - One spare wheel with holder in front of the front wall - 2" kingpin - Galvanised steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanised front connection strip - 4 wheel chocks with holders on the front wall - Bracket for beacon at rear of trailer - Recess at rear of gooseneck for ALU entry ramps - Galvanised folding supports under the loading platform's rear bevel - Cover plates to bridge gap between ramps and loading platform - White reflective tape according to EU regulations on sides, extendable section, and rear in red - Electro-hydraulic unit at the rear, under the loading platform - Brackets for warning signs on both left/right of gooseneck and ramps, with socket - Ramp control valves fitted on right-hand side of trailer - Mudflap at the trailer rear - Manual and documentation on USB stick - ALU side boards and rear wall on gooseneck approx. 2,440 x 400 mm - Rear galvanised plug-in stanchions, removable (superstructure length approx. 2,560 mm) - Four approx. 400 mm extendable warning signs, approx. 423 x 423 mm, each with a position light - 3 pairs of WADER container locks in the loading platform for 20ft, 30ft or 40ft container - 6 pairs of stake pockets 100x50 mm in outer frame of loading platform - Galvanised extendable width extensions, approx. 230 mm per side - 20 x 20 mm square climbing strips every 200 mm on the outer frame of the loading platform bevel - Sanded, painted anti-slip layer on checker plates over kingpin and loading platform - Holder for beacon on warning signs - European reflector boards (red-yellow) at the rear - 80 km/h speed limit stickers on rear and both sides - Load manometer for determining axle loads including load chart - HRM Metallisation (High Resistance Metallisation) of outer frame - Complete steel structure shot-blasted, then defined visible surfaces metallised with ZINACOR 850 (Zinc 85% - Aluminium 15%) hot-finished

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 11.000 kg, azami yük ağırlığı: 38.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava kaldıracı, renk: gri, lastik boyutu: 235/75 R 17,5, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading platform: - Telescopic loading platform with rear bevel approx. 1,000 mm x 8° - 1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses with 15 x 15 mm square climbing strips and lower section widenings - Between the 1st and 2nd axles, one pair of fixed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the chamfer as well as projecting into the loading platform to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings on the outside (LC 5,000 daN) - 2 pairs of fold-out lashing rings on the outside (LC 10,000 daN) - Cutouts on the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) - Includes 3-piece removable galvanized covers over the wheel recesses – max. point load 3.5 t / piece Hydraulic two-piece steel ramps: - One pair of galvanized two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting system, and lateral hydraulic adjustment Axles and tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift/lower valve - Axle tools - Tires 235/75 R 17.5 Accessories included: - 2” King pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with holder in front of the front wall - Yellow-red air couplings on the galvanized connector bar at the front - 4 wheel chocks with holder on the front wall - Mounting at the rear of the gooseneck for ALU loading ramps - Galvanized extendable widenings, extendable by approx. 230 mm per side - Galvanized folding supports under the bevel of the loading platform - Bracket for a beacon lamp at the rear of the trailer - White reflective tape according to EU regulations on the sides, extendable parts and rear in red - Gooseneck and rear panel left and right with a holder for warning signs including receptacle - One mud flap at the rear of the trailer - European reflector plates (red-yellow) at the rear of the trailer - On gooseneck: plug-in ALU side and rear boards approx. 2,440 x 400 mm - Rear galvanized plug-in stakes removable (superstructure length approx. 2,560 mm) - 2 pairs WADER container pockets in the loading platform for a 20 ft or 30 ft container Dodpfxjup U Hzs Af Tjku - 3 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - One removable galvanized intermediate table with 1 pair of WADER container pockets - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the loading platform chamfer - Four extendable warning signs, approx. 400 mm extendable, size approx. 423 x 423 mm, each with a position lamp - Holder for beacon lamp fitted to warning signs - 80 km/h speed stickers at the rear and on both sides - Load manometer for determining axle loads, including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (Zinc 85% - Alu 15%) Optional extras: - One toolbox on the gooseneck

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 10.350 kg, azami yük ağırlığı: 39.150 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava/hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of fixed built-in wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses equipped with 15 x 15 mm square climbing strips and lower-section extensions - 1 pair of fixed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm - 3-part removable galvanized covers over wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the ramp and extending into the load area to accommodate an excavator bucket arm approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm depression (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece ALU ramps: - One pair of single-piece ALU ramps approx. 2,500 x 600 mm - Ramps with spring assist and manual lateral adjustment - Maximum load per pair: 24,000 kg Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tools - Tyres 235/75 R 17.5 - TPMS (Tire Pressure Monitoring System) in compliance with ECE R 141 Accessories included: - One spare wheel with bracket in front of the bulkhead - 2" kingpin - One galvanized steel bulkhead ca. 400 mm high - Yellow-red air couplings at the galvanized front coupling strip - 4 chocks with bracket at the bulkhead - Accommodation at the rear of the gooseneck for ALU approach ramps - Galvanized extensions, extendable approx. 230 mm per side - Galvanized folding supports under the rear incline of the loading area - Bracket for a rotating beacon at the rear of the trailer - White reflector tape in accordance with EU requirements on sides, red on extension and rear - On the gooseneck and rear panel, bracket for warning boards including socket, left and right - On the gooseneck, plug-in ALU side walls and rear wall approx. 2,440 x 400 mm - Removable rear galvanized stanchions (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area - One removable galvanized intermediate table with 1 pair WADER container pockets - 20 x 20 mm square climbing strips every 200 mm along the outer frame of the loading area's rear incline Dedpfx Aeiu Er Aef Toku - Non-slip sand coating painted onto the checker plate on the gooseneck and loading area - Four warning boards extendable by approx. 400 mm each, approx. 423 x 423 mm with position light - Bracket for rotating beacon on warning boards - 80 km/h speed stickers on the rear and both sides - Load gauge for axle load determination including load chart - HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces metallically finished with ZINACOR 850 (Zinc 85% - Alu 15%) hot metalized

Durumu: yeni, toplam ağırlık: 50.000 kg, azami yük ağırlığı: 38.100 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 760 mm, süspansiyon: hava kaldıracı, renk: gri, lastik boyutu: 205/65 R17.5 3PMSF, Donanım: ABS, Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Loading Platform: 5 pairs of fold-out lashing rings on the outside 3 pairs of fold-out lashing rings on the outside 1 pair of horizontal lashing rings at the front end of the platform Cut-outs in the outer frame of the loading platform for attaching tension straps Approx. 48 mm thick hardwood flooring, checker plate flooring above the axles Landing Gears: JOST landing legs with 2-speed gearbox, lifting capacity 24 t Axles and Tyres: BPW axles, two fixed axles, two steered trailing axles, air suspension, drum brakes, raise/lower function Trailing steering axles with electro-magnetic reverse lock, activated via reverse gear or manually Axle tool Tyres 205/65 R17.5 3PMSF Brake System: WABCO brake system according to EU regulations, with EBS-E Steel Construction: High-strength fine-grained steel construction Steel Grades: S355J2+N/S355MC S690QL/S700MC Electrical Equipment: Electrical system according to EU regulations, lighting: 24 Volt ASPÖCK-NORDIK ASPÖCK-UNIBOX at the front connection panel, with 24N, 24S & 15 pin sockets Connections according to ISO Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by 2-component zinc-dust primer Premium 2-component topcoat, single colour in MB 7350 Novagrau No metallic finish possible Rear section metallized and painted RAL 9010 Accessories Included: 1 spare wheel 205/65 R 17.5 TPMS tyre pressure monitoring system according to ECE R 141 Galvanized front connection bar with yellow-red air couplings 4 chocks with holder at the front wall Mounting at rear of gooseneck for ALU loading ramps Galvanized folding supports under the loading platform’s rear chamfer Holder for a warning beacon at the rear of the trailer Height-adjustable tarpaulin superstructure Galvanized front wall with tensioning mechanism for sliding curtains Height-adjustable by approx. 400 mm Roof brand "EDSCHA" sliding forward on ALU roof support profiles, screwed front and rear walls On platform: 3 pairs of adjustable stanchions Rear of superstructure can be hydraulically widened left and right by approx. 750 mm Sliding roof with upward swinging portal beam Sliding tarpaulin with 700 mm length reserve, securing straps at approx. 600 mm intervals Height upper edge of superstructure approx. 3,960 mm Driving with open sliding roof is not permitted and will damage the tarpaulin Suspension rail for ALU loading ramps at the rear of the vehicle At the gooseneck and at the left and right rear panel: each with a bracket for warning boards including socket Mudflap at the rear of the trailer European reflector boards at the rear of the trailer 7 pairs of stanchion pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading platform Lift axle on the front axle with TEBS E control, depending on current axle load and loading status Rear of superstructure with closed ALU wing doors Anti-slip sand finish painted on checker plates on gooseneck and platform Central lubrication system BEKAMAX, standard grease NLGI-2, removable protective cover for pump 80 km/h speed sticker at rear and on both sides Load gauge for axle load determination including load chart Djdpfxjtphtmo Af Toku

Durumu: yeni, toplam ağırlık: 51.600 kg, boş ağırlık: 10.000 kg, azami yük ağırlığı: 41.600 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Cargo area: - Gooseneck, length approx. 4,100 mm with central beam - Cargo area in extendable design, length approx. 9,500 mm with rear taper approx. 350 mm x 10° and integrated mounting rail for attaching loose aluminum loading ramps - Pneumatic locking with conical locking pins and reinforced locking positions - Supply lines are protected within the extendable beams and automatically adapt to the respective cargo area length Axles, suspension, and tires: - BPW axles and suspension, all axles hydro-mechanically forcibly steered - Mounted on turntable - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Tires: 235/75 R17.5 twin tires Paintwork: - 6-coat final treatment - Entire steel structure shot-blasted after welding - One coat of zinc-based primer, one coat of adhesion primer - Final paint with two coats of 2-component acrylic paint, single color in MB 7350 Novagrau, then hollow sections sealed with special wax Steel construction: - Steel construction made from high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) Dkedpfxsiuy Nle Af Tsu - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - MAG welding process according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Steel front wall, approx. 1,600 mm high - Round NATO socket on the front connection bar - 3 kW electro-hydraulic unit for controlling hydraulic functions - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets recessed in the outer frame of the gooseneck for stakes approx. 100x50 mm - 1 cross stake pocket bar mounted in the gooseneck cargo floor for stakes approx. 100x50 mm (1x at the rear of the gooseneck) - 2" kingpin - Mechanical landing legs with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Approx. 32 mm wooden floor encased in aluminum omega profiles on the gooseneck and cargo area - One locking position per extension, approx. every 500 mm - 10 pairs of recessed horizontal lashing rings in the outer frame of the cargo area, foldable outward - 6 pairs of stake pockets recessed in the outer frame of the cargo area for stakes approx. 100x50 mm - 2 cross stake pocket bars installed in the cargo floor of the cargo area for stakes approx. 100x50 mm - INOX toolbox approx. 1,250 x 500 x 550 mm - Rear cross member with a bevel approx. 350 mm at 10° - Integrated mounting rail for loose aluminum loading ramps at the rear cross member - 1 pair of drop-leg supports at the rear cross member - Fenders on all axles - Central lubrication system with 1 pump - Remote axle steering operated from front and rear via cable remote control with pushbuttons and single-track monitoring of the axles - Under the gooseneck and on the left and right at the rear cross member, one 7-pin socket each for warning boards - One 7-pin socket at the rear cross member - Container locks "TWIST-LOCKS" in the cargo area for transporting 2x 20ft and 1x 40ft containers - Radio remote control for axle steering in addition to cable remote control, with 2 indicator lights at the receiver for single-track monitoring - 2 axle load gauges + axle load chart - 4 warning panels approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then the defined visible areas metallized with ZINACOR 850 (zinc 85% - aluminum 15%) by hot finis

Durumu: yeni, toplam ağırlık: 45.000 kg, boş ağırlık: 9.500 kg, azami yük ağırlığı: 35.500 kg, işletme ağırlığı: 9.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.540 mm, süspansiyon: hava, renk: gri, lastik boyutu: 435/50 R 19.5, Donanım: ABS, Loading platform in extendable design: Loading platform with hardwood floorboards, rear chamfer approx. 1,000 mm x 8° 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm 2 pairs of lashing rings (LC 5,000 daN) 1 pair of lashing rings (LC 10,000 daN) 6 pairs of folding external lashing rings (LC 5,000 daN) 2 pairs of folding external lashing rings (LC 10,000 daN) Cut-outs in the outer frame of the loading platform for hooking in tensioning straps (LC 2,000 daN) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: Premium, durable corrosion protection for the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer High-quality single-color 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic effect paint possible Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting Sockets: 24N, 24S & 15-pin Axles and tires: BPW axles, air suspension, disc brakes (377 mm), with lift/lower function The trailing steering axles can be locked for reversing by electro-magnetic control via reverse gear or manually Axle tools Tires 435/50 R 19.5 Accessories included: At the front galvanized connection rail, yellow-red air couplings 4 wheel chocks with holders 2" king pin Galvanized steel front wall, approx. 1600 mm high, EN12642-XL White reflective tape to EU standards on the sides, on the extension, and red at the rear Loading area with heavy-duty hardwood flooring 9 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform 1 spare wheel holder under the loading platform, right side of direction of travel Galvanized drop-down supports under the loading platform chamfer Sliding hook-in strips for ALU loading ramps at the rear of the vehicle European reflective signs (red-yellow) at the rear of the trailer A mudflap at the rear of the trailer A bracket for a rotating beacon at the rear of the trailer On the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket 1 HDPE toolbox 620x360x610 under the loading platform, left side of direction of travel 4 pairs of WADER container locks in the loading platform for 1x 20ft container or 1x 40ft container; the extension is prepared with an additional locking position for a 45ft container 3 pairs of crosswise stake pocket strips mounted in the loading platform for 100 x 50 mm plug-in stakes Lift axle on the front axle with control via TEBS E depending on current axle load and load status Speed stickers 80 km/h at the rear and on both sides Four warning panels, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light. Each warning panel with a bracket for revolving beacon Dksdpfsk Eammjx Af Teu Load gauge for determining axle loads including load chart HRM metallization (High Resistance Metallisation) of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces are metallised

Durumu: yeni, toplam ağırlık: 45.000 kg, boş ağırlık: 10.600 kg, azami yük ağırlığı: 35.400 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 940 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Loading platform: - Loading platform with extendable design - Loading platform with hardwood planks, approx. 500 mm x 8° rear chamfer - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading platform for attaching tension straps Brake system: - Brake system compliant with EU regulations with EBS-E (2S2M) Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) topcoat, single-color in Novagrau (Nova grey) - Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint not available Landing legs: Dedpfx Asl Ux Rwef Tjku - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel construction made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Electrical system: - Electrical system according to EU regulations, LED lighting 24 Volt - Sockets: 2x 7-pin & 1x 15-pin Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), with lift/lower function - Hydro-mechanically forced steering - Axle tool kit - Twin tires 235/75 R 17.5 Included accessories: - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holders - 2" king pin - Galvanized steel front wall approx. 1600 mm high - White reflective tape as per EU regulations on sides, extension, and rear in red - Loading platform with heavy-duty hardwood floor - Steering from front and rear via cable - Remote control via push buttons with single-track axle monitoring - Radio remote control for auxiliary steering - 9 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform - Galvanized folding supports under the loading platform chamfer - Sliding hook-in rail for ALU ramps at the rear of the vehicle - European reflective signs (red-yellow) at the rear of the trailer - One mudflap at the rear of the trailer - One bracket for a rotating beacon at the rear of the trailer - On the gooseneck and on the left/right rear panel each: one holder for warning signs including socket - INOX toolbox 1,500 x 390 x 810 under the loading platform on the right (direction of travel) - BEKAMAX (Pico) central lubrication system with standard grease NLHI-2 and removable guard for the pump - 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft container, or 1x 40ft container, with additional locking point in the extension for a 45ft container - 4 pairs of cross-mounted stake pocket rails in the loading platform, for plug-in stanchions 100 x 50 mm - Lift axle at the front axle with TEBS-controlled adjustment, depending on current axle load and loading status - Speed stickers 80 km/h at rear and both sides - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Holder for rotating beacon on warning signs - Load pressure gauge for axle load determination, including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then defined visible areas hot-finished metallized with ZINACOR 850 (Zinc 85% - Alu 15%)

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 11.300 kg, azami yük ağırlığı: 36.700 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.250 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 385/65 r 22,5, Donanım: ABS, Loading Area: Extendable loading platform with pneumatically operated locking mechanism A fixed intermediate table approx. 250 mm wide is mounted on the central beam 8 pairs of folding lashing rings (LC 5,000 daN) 3 pairs of folding lashing rings (LC 10,000 daN) Cut-outs in the outer frame of the loading area for hooking in tension straps (LC 2,000 daN) Axles and Tyres: BPW axles and suspension, all axles hydromechanically forced-steered Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tool kit 6 tyres 385/65 R 22.5 Brake System: Brake system according to EU regulations with EBS-E (2S2M) Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load) Steel Construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical System: Electrical system in line with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with 24N, 24S, and 15-pin sockets Connections per ISO: Dedpfohlz Shjx Af Toku 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting: Top-class and durable corrosion protection of the standard shot-blasted welded frame provided by a 2-component (2K) zinc-rich primer High-quality 2-component (2K) top coat in single-colour Nova Grey Rear end metallised and painted in RAL 9010 (pure white) Metallic paint not available Included Accessories: One bracket for warning signs, each at the gooseneck and the rear end plate, left and right, including socket Remote steering operated from front and rear using cable remote control with push-buttons, with single-track alignment of the axles Electro-hydraulic power pack 4 wheel chocks with holder on the front bulkhead 2" kingpin One galvanised steel headboard approx. 2,200 mm high Yellow-red pneumatic couplings on the galvanised connection rail at the front White reflective tape per EU regulations on the sides, on the extension, and red at the rear European reflective warning plates (red-yellow) at the rear of the trailer One mud flap at the rear of the trailer Manual and documentation Bracket for revolving beacon at the rear of the trailer Loading surface with approx. 30 mm thick wooden floor embedded in Omega profiles 10 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading area 1 spare wheel holder under the loading platform on the right in the direction of travel 6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2x 20ft containers, or 1x 40ft container; an additional locking point in the extension is provided for a 45ft container 5 pairs of cross-mounted stanchion pocket rails in the loading area for plug-in stanchions 100 x 50 mm One galvanised bracket crosswise under the loading platform (2,390 x 720 x 400 mm) Entry ladder mounted on the right side in the direction of travel HDPE toolbox 1,200 x 500 x 480 mounted at the front under the loading surface on the left in the direction of travel Lifting axle on front axle, control by TEBS E depending on current axle load and load status Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 general-purpose grease and removable guarding around the pump Red/white reflective tape in the loading platform extension A sand layer painted on the central beam as anti-slip protection Radio remote control for rear steering in addition to cable remote, with in

Durumu: yeni, toplam ağırlık: 60.800 kg, boş ağırlık: 13.250 kg, azami yük ağırlığı: 47.550 kg, dingil konfigürasyonu: 3 aks, süspansiyon: hava, renk: gri, lastik boyutu: 245/70 r17.5, Donanım: ABS, Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Extendable loading platform with rear taper approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of horizontal lashing rings at the front of the loading platform Cutouts in the outer frame of the platform for attaching tension straps Approx. 48 mm thick hardwood flooring, checker plate over the axles Two-piece steel ramps: One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding ramp sections, hydraulic lift mechanism, and hydraulically adjustable. Maximum load per pair: 40,000 kg Landing legs: JOST landing legs (mechanical) with two-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Dkjdsl Uxdkopfx Af Tou Brake system: Braking system according to EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Steel structure: Steel structure made of high-strength fine-grain steels Steel qualities: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer High-quality two-component (2K) topcoat in single-tone Nova Grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint possible Electrical system: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings at the galvanized front connection bar 4 wheel chocks with holder at the front wall One spare wheel with holder in front of the front wall Electro-hydraulic unit Remote steering front and rear via cable remote control with push buttons and single-track axle alignment control Mount for ALU loading ramps at rear section of the gooseneck European reflector boards (red-yellow) at the rear of the trailer White reflector tape as per EU regulations on the side, extension and rear Red at the rear At the gooseneck and ramps, one holder left and right for warning signs including socket Beacon holder at the rear of the trailer Galvanized folding support legs under the rear ramp of the loading area Control valves for ramps located on the right side of the trailer Cover plates to bridge the gap between ramp and loading platform One mud flap at the rear of the trailer Manual and description on USB stick BEKAMAX (Pico) central lubrication system with standard NLGI-2 grease and removable protection for the pump Plug-in ALU side and rear walls on the gooseneck approx. 2,440 x 400 mm Rear galvanized plug-in posts are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350x400x400 on the gooseneck, box covers oil fill plug 4 pairs of WADER container locks in the loading area for a

Durumu: yeni, toplam ağırlık: 102.000 kg, boş ağırlık: 29.600 kg, azami yük ağırlığı: 72.400 kg, işletme ağırlığı: 29.600 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 6.650 mm, yükleme alanı genişliği: 2.840 mm, yükleme alanı yüksekliği: 550 mm, renk: gri, lastik boyutu: 285/70 R19.5, Donanım: ABS, Gooseneck: - Gooseneck hydraulically liftable/lowerable and detachable - Length approx. 3,650 mm - For tractor units: 6 x 4 or 8 x 4 2-Axle Front Bogie: - Hook pick-up at front and rear - Chassis length x chassis width approx. 2,200 mm x 2,850 mm Excavator Deck 'BB-A': - Telescopic excavator deck 'BB-A' with drive-over bridge hooks at the front and bolt-eye coupling at the rear - Length x base width approx. 6,650 mm x 2,850 mm - Beam height x beam width approx. 400 mm x 1,350 mm - Loading height 550 mm with ground clearance 150 mm 4-Axle Rear Bogie: - Mechanical bolt-eye coupling for connecting a low-bed at the front, rear cross member at the back - Bogie length x bogie width approx. 5,480 mm x 2,850 mm - Numerous lashing points Pendulum Axle and Tyres (Front and Rear Bogie): - "PENDULUM AXLE", all axles hydromechanically forced-steered - Burst hose valve on axle compensation cylinders with automatic reset function - Hydraulic cylinders with shut-off valves and locking pins to secure in raised position - Final paint of axles with double-layer 2-component paint in MB 7350 Novagrau, single-color finish - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tyres: 285/70 R19.5 Remote Steering: - Steering from front and rear via cable remote control with push-buttons, including single-track alignment monitoring - Socket for remote steering operation on the gooseneck - Cable remote control with push-buttons including single-track alignment monitoring Included Accessories: - At the galvanized connection bar at the front: yellow-red air couplings - Steel front wall approx. 400 mm high - 4 wheel chocks - 3.5" kingpin - One 7-pin socket at left and right rear of the gooseneck for warning signs - Support bracket with winch for spare wheel at the front of the gooseneck - Truck hydraulic connection with flow controller (40 l/min), including bracket for suspension of supply lines; tractor unit tank must be at least 80 liters with couplings - Plug-in ALU side and tail boards on the gooseneck, approx. 400 mm high, anodized - Control lever on the gooseneck protected by a fold-down cover - Separate air connection with air gun on the gooseneck - Central lubrication system BEKAMAX, 1x on the gooseneck, 1x on the 2-axle bogie, and 1x on the 4-axle bogie - Variomax tool kit - Multi-coupling hydraulic connections on the gooseneck and in the area of the low-bed hook-up - 2 spare wheels - One 7-pin socket left and right, at the front and rear end of the rear bogie for the warning sign - Front bogie with separate air connection for air tools - Foldable extensions with steel deck inserts, width adjustable from approx. 2,850 mm to approx. 3,250 mm - Steel deck inserts can be placed in 2 positions to create a lowered loading area - Steel mats with 12 mm thick rubber surface - Screw-in option (⌀ 40 mm) every approx. 500 mm on the outside flange of the outer tube of the excavator deck for lashing rings - One locking position every approx. 500 mm at the extension with mechanical lock - Socket for cable remote control of the remote steering at the rear bogie - 2 reversing lights on the rear panel - Four warning signs extendable by approx. 2,000 mm approx. 423 x 423 mm with a position light - 1 work light left/right on the rear panel of the gooseneck with separate on/off switch - Two INOX toolboxes approx. 855 x 340 x 390 mm - 1-cylinder Hatz diesel engine (Silent Pack) - Wireless remote control for the remote steering Dedowcmhaspfx Af Teku