Kullanılmış Müller-Mitteltal Kwh Fragmanlar satın al (255)

Durumu: yeni, azami yük ağırlığı: 31.630 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.520 mm, * T 4: * EBS * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display function in the truck via EBS signal – without truck-side installation * Warning sign packages front & rear * Contour marking tape on sides and rear, reflective * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED beacon * 24 V – 15-pin and additionally 12 V – 7+4 pin power cable * Extended connector lines for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on the right side * Closed single mudguard at the front (plastic) * Straight steel mud flaps at the rear, each with spray suppression * Side underrun protection * Extended offset cranking by 500 mm forwards * Bogie platform extension at the front by 520 mm with 45° corners, 3 integrated compartments incl. lids and lockable * Chassis made of high-strength fine-grained steel * Floor above the bogie platform made of 50 mm, and in low-bed platform made of 60 mm softwood * Outer planks of loading ramps made of 50 mm bamboo wood * Four stake pockets per side (no stakes included) with simultaneous 2 t lashing possibility * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, front and rear pairs of 13.4 t lashing rings on outer frame, 4 pairs per side of 10 t lashing rings, swiveling and lowerable, loadable in all directions and integrated in the outer frame, 2 pairs of 6.4 t lashing rings on the side in the excavator arm rest, 8 pairs of galvanized folding outriggers for 3 m total width (not at rear slope) * Widening planks stored sideways left in storage compartment * Excavator arm rest above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * Mechanical drop legs at rear * Hydraulic, hot-dip galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp displacement on sliding tube from ramp shaft * Loading area above slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded deck height approx. 860 mm (including 860 mm approach slope) Nodsrczm Djpfx Afgjku * Chassis, bogie, loading ramps, and rear mechanical drop legs hot-dip galvanized * Axles, springs, air tanks, and slewing ring painted in black tone * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Available from week 21 / 2026

Durumu: yeni, azami yük ağırlığı: 6.810 kg, toplam ağırlık: 9.600 kg, dingil konfigürasyonu: 1 dingil, yükleme alanı uzunluğu: 4.030 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 700 mm, Üretim yılı: 2025, * EK 9.6 ----Braking System: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * SAF axle ----Suspension: * Parabolic springs ----Drawbar / Flange Towing Eye: * Drawbar as central beam with 40 mm screw-in towing eye * Continuously adjustable drawbar height with spindle lift mechanism instead of fixed drawbar ----Coupling Height: * Standard coupling height approx. 900 mm (+/- 150 mm) ----Electrics / Lighting: Nodpfxjw Ndr Us Afgjku * Tire pressure monitoring with display capability in the truck via EBS signal – no installation required on truck side * 15-pin power connector * LED rear lights * Flashing side marker lights ----General Attachments: * Front landing gear * Closed plastic mudguards * Folding underrun protection for pavers ----Chassis: * Chassis made from high-tensile fine-grain steel ----Tipper Body: * Pallet-compatible 3-way tipper body * 700 mm steel front wall * Continuous asymmetric aluminium side walls – foldable without central stanchion, with long-travel locks and pivoting via manual central locking * 800 mm high steel tailgate with automatic opening during rear tipping * 4 mm Hardox 450 steel floor ----Load Securing: * 2 pairs of 3 t lashing rings on each side, recessed and folding in the steel floor ----Paintwork: * Chassis, drawbar, underrun protection hot-dip galvanized * Tipper body painted RAL 9010 pure white ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 10.760 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 14.4: ----Braking System: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring-loaded cylinders Nsdpfx Aervvfljfgeku ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm (total length 2,250 mm) * 40 mm flange eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General Attachments: * Jost landing leg at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox front right, exterior of the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Preparation in front of the bulkhead for subsequent installation of container locks * Bolted bulkhead made of smooth sheet metal * Side panels made from trapezoidal profile steel plate, foldable with sideboard assist spring * Rear wall made of steel, can be inserted between the ramps (bracket for storage provided inside in front of the bulkhead when not in use) * Rear stanchions bolted ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity at 480 mm intervals * Optionally, installation of 3 t drop lashing rings every 600 mm possible * 1 x 6.3 t lashing ring in each corner at the front and rear * Various bores in front and end crossmember for 1.2 t lashing options ----Ramps: * One-piece mechanical steel mesh ramps with spring-assist, suitable for single-person operation, approx. 2,750 x 600 mm (can be compressed to 20 mm) * Rear approach angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, loading ramps, and rear wall * Sideboard color RAL 9010 pure white * Side panel paintwork in any RAL color available for an additional charge ----Information: * -- Reinforced and certified body according to EN 12642 XL, incl. load securing certificate -- * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from calendar week 08/2026

Durumu: yeni, azami yük ağırlığı: 10.760 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes Nkodsxglibjpfx Afgsu * Electronic braking system (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with balancing unit ----Drawbar / Flange Drawbar Eye: * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to total 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General Attachments: * Jost landing gear at front * Externally mounted hot-dip galvanized folding supports at rear * Plastic toolbox mounted front right externally on the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Pre-fitted for subsequent installation of container locks in front of bulkhead * Bolt-on smooth steel bulkhead * Side walls made of trapezoidal-profiled steel, foldable with drop side spring assist * Steel tailgate, insertable between ramps (storage mount inside at front wall when not in use) * Removable rear stanchions, bolted ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes for 1.2 t lashing options in the bulkhead and rear crossmember ----Ramps: * One-piece mechanical grating ramps with spring assist for single-operator use, approx. 2,750 x 600 mm (can be compressed to within 20 mm) * Rear drive-up angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, ramps, and tailgate * Drop side color in RAL 2011 deep orange * Painting of side walls in custom RAL color available at extra charge ----Information: * --Reinforced and certified structure in accordance with EN 12642 XL including load securing certificate-- * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available from calendar week 08/2026

Durumu: yeni, azami yük ağırlığı: 10.760 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring actuators ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange drawbar eye ----Lighting / Electrics: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox, front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood flooring * Preparation in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Fold-down trapezoidal-profiled steel side walls with drop side spring assist * Steel rear wall, can be slid in between the ramps—holder for storage inside the bulkhead when not in use Njdpfeq Dyvvex Afgjku * Bolted rear stanchions ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option for installing 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various holes in bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring system for single-person operation, approx. 2,750 x 600 mm (can be pushed together up to 20 mm) * Rear entry ramp angle approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, bulkhead, access ramps and rear wall * Drop side color in RAL 9010 pure white * Side wall painting in any RAL color available at extra charge ----Information: * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available from week 08/2026

Durumu: yeni, azami yük ağırlığı: 10.760 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2026, * ETÜ-TA-R 14.4: ----Brake System: * Drum brakes * Electronic braking system (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Flange Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm, total 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * TPMS (tyre pressure monitoring system) * LED lighting ----General Equipment: * Jost landing leg at the front * Externally mounted, hot-dip galvanized rear folding supports * Plastic toolbox at the front right on the bulkhead exterior * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: Nedexglh Rjpfx Afgsku * 50 mm softwood floor * Fixture in front of the bulkhead for retrofitting container locks * Bolted smooth steel bulkhead * Drop sides made of trapezoidal steel sheet, foldable with drop side spring assists * Rear wall made of steel, retractable between the ramps – storage bracket when not in use in front of the bulkhead * Rear stanchions bolted ----Load Securing: * Perforated outer frame angled approx. 45° with 2 t lashing capacity every 480 mm * Optional installation of 3 t recessed lashing rings every 600 mm * One 6.3 t lashing ring in each corner at the front and rear * Various holes in front and rear crossmembers for 1.2 t lashing capability ----Ramps: * One-piece mechanical grating ramps with spring system for single-person operation, approx. 2,750 x 600 mm (can be pushed together down to 20 mm) * Rear approach slope approx. 860 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, bulkhead, access ramps and rear panel * Drop side colour RAL 2011 deep orange * Optionally, side panels can be painted in any RAL colour at extra charge ----Info: * --Reinforced and certified bodywork according to EN 12642 XL, including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to alterations and prior sale ----Delivery time: * available from CW 08/2026 (week 8/2026)

Durumu: yeni, azami yük ağırlığı: 31.630 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation, front and rear * Tire pressure monitoring system with cab display option via EBS signal – no installation required on the truck side * Warning sign package front & rear * Reflective contour tape, side and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED beacon * 24 V – 15-pin and additional 12 V – 7+4-pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting Nkodjl Th Evepfx Afgeu * Straight drawbar with 40 mm towing eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and basket-type spare wheel holder, right side * Closed single plastic mudguard front * Straight rear steel splash guards, each with spray suppression * Side underrun protection * Extended offset by 500 mm to the front * Extended turntable platform at the front by 520 mm with 45° corners and three recessed storage compartments incl. lid, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, low-bed platform floor made of 60 mm softwood * Outer planks of ramps made of 50 mm bamboo wood * Four stake pockets per side (no stakes supplied), each with 2 t lashing points * Load securing package consisting of: 2 lashing eyes (6.4 t) front left and right on the main frame of the turntable platform; one pair of 13.4 t lashing rings at the front and rear outer frames; four pairs of 10 t swivel and retractable lashing rings per side, loadable in all directions and integrated into the outer frame; two pairs of 6.4 t lashing rings on the side in the excavator stick rest; eight pairs of galvanized folding outriggers for 3 m overall width (not on rear incline) * Widening planks stored left side in storage compartment * Excavator stick rest over rear axle to end of rear incline, approx. 2,300 x 740 x 190 mm * Mechanical rear support legs * Hydraulic, hot-dip galvanized ramps, approx. 3,000 x 720 mm * Hydraulic side ramp displacement on guide tube from ramp shaft * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Laden loading height approx. 860 mm (incl. 860 mm rear incline) * Chassis, turntable, ramps, and rear mechanical support legs hot-dip galvanized * Axles, springs, air tanks and turntable painted in black tone * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 21 / 2026

Durumu: kullanılmış, dingil konfigürasyonu: 3 aks, ilk tescil: 04/2000, yükleme alanı uzunluğu: 10.790 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 950 mm, toplam uzunluk: 14.790 mm, toplam genişlik: 2.500 mm, süspansiyon: çelik, Üretim yılı: 2000, Ek bilgi : Marka: MÜLLER MITTELTAL Model: TS4 Yapı: alçak şasi treyler (platform L=10790 mm / G=2500 mm / Y=950 mm) Yıl: 2000 Süspansiyon: çelik yaprak Frenler: kampana Boyutlar: U/G: 14790 mm / 2500 mm Ağırlıklar: azami/boş: 57000 kg / 11800 kg HİDROLİK RAMPALAR / ÇELİK SÜSPANSİYON / KAMPANA FREN Süspansiyon tipi: yapraklı süspansiyon Frenler: Kampana = Daha fazla bilgi = Süspansiyon: yapraklı süspansiyon Boş ağırlık: 11.800 kg Taşıma kapasitesi: 45.200 kg Azami yüklü ağırlık (GVW): 57.000 kg Daha fazla bilgi için lütfen Andrei Somov, Mark Ševtšenko veya Deniss Urmaker ile iletişime geçiniz. Njdpjuwu Ezsfx Afgjku

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2001, toplam uzunluk: 10.000 mm, toplam genişlik: 2.510 mm, süspansiyon: çelik, Üretim yılı: 2001, = Ek Bilgi = Marka: MÜLLER MITTELTAL Model: T 3 Yapı: Platform (platform L=8.400 / G=2.510 / Y=940 mm) Yıl: 09.2001 Süspansiyon: Çelik (makaslı) Frenler: Kampana Boyutlar: U/G: 10.000 mm / 2.510 mm Ağırlıklar: azami/boş: 24.000 kg / 6.100 kg Taşıma kapasitesi: 17.900 kg Azami yüklü ağırlık (GVW): 24.000 kg Daha fazla bilgi için lütfen Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche veya Deniss Urmaker ile iletişime geçiniz. Nodjuwvbqspfx Afgsku

Durumu: yeni, azami yük ağırlığı: 10.750 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: ----Braking system: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS tire pressure monitoring system * 15-pin electrical connector * LED lighting ----General fittings: * Landing gear (support winch) at the front * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm, front right, fitted externally on the front wall * Side underrun protection * Plastic quarter mudguards ----Low-loader platform: * 50 mm softwood flooring * Preparation in front of the front wall and at the rear slope for subsequent installation of container locks for transporting 20" containers * Bolted, smooth sheet metal front wall * Side walls made of trapezoidal-profiled steel, centre-split and foldable * Steel rear wall insertable between ramp brackets; can be stowed inside at front wall when not in use * Bolted rear stanchions ----Load securing: * Perforated external frame angled at approx. 45 degrees with 2 t lashing capacity every 480 mm Nkjdpfx Ajv Eq Evofgsu * Option to install 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes in the front and rear cross members for 1.2 t lashing capability ----Ramps: * One-piece mechanical grating ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 mm ----Paint finish: * Drawbar, front wall, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tank, flange towing eye, and landing gear painted in black shade * Drop side boards painted RAL 9010 pure white * Side wall painting in an RAL color of choice possible at extra cost ----Information: * Reinforced and certified construction according to EN 12642 XL, incl. load securing certificate * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex location Egestorf on the A7

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, 300 mm range, with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical support winch at the front * Rear: 2 mechanical folding supports * Plastic toolbox, approx. 750 x 350 x 300 mm, right-hand side * Bolted underrun protection * Plastic quarter mudguards ----Chassis: * Main frame made of high-strength fine-grain steel ----Tipping Body: * Net hooks on the sides and rear in the central locking mounts plus 2 pieces on the front wall * 2-way pallet steel tipper body, fixed front wall of smooth sheet, continuous drop sides (without center stanchions, fold-down with sideboard spring assist) and swinging via manual central locking * Rear stanchions bolted * Steel rear wall inserted in front of the ramps * 1 x 5 t lashing point in each corner and 4 x 3 t lashing rings each side, recessed in the outer frame * 4 mm fine-grain steel floor ----Ramps: * Two-part mechanical steel grid access ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (can be manually telescoped to 80 mm overlap) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical drop supports, and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Drop sides and platform painted RAL 9010 pure white * Side wall and tipping body paintwork in any RAL color available at extra charge ----Info: * New vehicle with manufacturer’s warranty Nkjdpfxotr Sucs Afgju * Subject to errors and prior sale ----Delivery Time: * Available from week 07/2026

Durumu: yeni, azami yük ağırlığı: 10.400 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release mechanism for spring-actuated cylinders * Drum brakes Nksdpfx Afstr St Usgou ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / flange eye: * Height-adjustable drawbar by 300 mm with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring system with readout in truck via EBS signal, no installation required on truck side * 15-pin power connector * LED tail lights ----General accessories: * Mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm, mounted on right side * Bolted underrun protection * Plastic quarter mudguards ----Chassis frame: * Main frame made of high-tensile fine-grained steel ----Tipper body: * Mesh hooks on the sides and rear at the central locking bearings, plus 2 hooks at the front wall * Steel pallet - 2-way tipper body with fixed steel front wall, continuous smooth steel side walls, folding without center stanchions using drop-side spring lifters, also swinging via manual central locking * Rear stanchions bolted * Steel rear panel slid in front of the ramps * 1 x 5 t lashing point in each corner, 4 x 3 t lashing rings recessed per side in the outer frame * 4 mm floor made of fine-grained steel ----Ramps: * Two-part mechanical grating ramps with aluminium nose sections, 2,150 + 1,300 mm x 600 mm (manually retractable to 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange eye, and support winch painted in black tone * Sideboards and tipper body finished in RAL 9010 pure white * Optional: painting of side walls and tipper body in any RAL color available at additional cost ----Additional information: * New vehicle with manufacturer’s warranty * Subject to prior sale and errors ----Delivery time: * Available from week 07/2026

Durumu: yeni, azami yük ağırlığı: 10.750 kg, toplam ağırlık: 14.400 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 7.000 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 14.4: ----Braking System: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizer assembly ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * LED lighting ----General Attachments: * Support windlass at the front * Externally mounted folding support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, located front right on the outside of the front wall * Side underrun protection * Plastic quarter fenders ----Low Loader Platform: * 50 mm softwood floor * Preparation in front of the front wall and rear incline for retrofitting container locks for transporting 20" containers * Bolted front wall made of smooth sheet metal * Drop-side walls made of trapezoidal-profile steel sheet, foldable, split in the middle (1x) * Steel rear wall, can be slid in and stored between the ramp mounts or in front of the front wall when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, angled at about 45 degrees with 2 t lashing capacity every 480 mm * Option to install 3 t drop-type lashing rings every 600 mm * In each corner at front and rear, 1 x 6.3 t lashing ring * Various holes in the front and end cross members for 1.2 t lashing capability Nsdpsv D Tcbefx Afgsku ----Ramps: * One-piece mechanical grating loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compacted to 20 mm) * Rear ramp angle approx. 860 mm chassis height ----Wheelbase: * Wheelbase 1,140 mm ----Paint Finish: * Drawbar, front wall, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support windlass painted in black * Sideboards painted in RAL 9010 pure white * Painting of side walls in RAL color of your choice at extra cost ----Information: * Reinforced and certified body according to EN 12642 XL, including load securing certificate * New vehicle with manufacturer warranty * Subject to prior sale and errors excepted ----Delivery Time: * Available immediately ex works Egestorf (A7 motorway)

Durumu: kullanılmış, azami yük ağırlığı: 22.500 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 05/2002, yükleme alanı uzunluğu: 9.250 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, Toplam ağırlık: 24.000 kg / 30.000 kg Boş ağırlık: 7.500 kg Yük kapasitesi: 16.500 kg / 22.500 kg Toplam uzunluk: 11.600 mm Yükleme uzunluğu: toplam yaklaşık 9.250 mm / alçak platform yaklaşık 7.150 mm / köprü bölümü 2.100 mm Genişlik: 2.550 mm / yükleme genişliği yaklaşık 2.500 mm Yükleme yüksekliği: 900 mm Diğer bilgiler - Tekerlek yuvası - Ekskavatör arm yuvası - Hidrolik rampalar, bölmeli, yaklaşık 640x3.300 mm - 3 m'ye kadar genişletme Nedpox E I Uaofx Afgeku - Uyarı panoları - Yükleme alanı altında depo - Büyük sabitleme paketi - Köprü kısmında depo - Payandalı cep - LED geri vites farları - 235/75R17,5 çift lastik - BPW akslar - Alt koruma Yeni ve ikinci el 3 ve 4 dingilli alçak yataklı treylerler hemen teslim. Daha fazla bilgi için

Durumu: kullanılmış, azami yük ağırlığı: 8.000 kg, toplam ağırlık: 11.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 10/2000, yükleme alanı uzunluğu: 5.600 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 900 mm, toplam genişlik: 2.550 mm, Toplam ağırlık: 11.000 kg Boş ağırlık: 3.000 kg Yük kapasitesi: 8.000 kg Toplam uzunluk: 7.450 mm Nkedpfx Aswz Drgsfgou Yükleme uzunluğu: toplamda 5.600 mm, bunun 1.000 mm'si arka eğim Genişlik: toplam genişlik 2.550 mm / kasa içi genişlik 2.480 mm Yükleme yüksekliği: yaklaşık 900 mm Diğer bilgiler: - Yan panjur yüksekliği: 400 mm, bölmeli, katlanabilir - Bölmeli yaylı rampalar, ölçüler yakl. U: 3.380 mm G: 600 mm - Rampalar kaymaz kontrplak kaplı - Büyük yük sabitleme paketi - BPW akslar - 235/75 R17,5 lastikler - LED geri vites lambası - Plastik alet kutusu

Durumu: yeni, azami yük ağırlığı: 8.620 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2024, *KA-TA-R 11.9:* Brakes: - Electronic Braking System (EBS) - Emergency release device for spring brake cylinders Nsdpjm Angvofx Afgeku - Drum brakes Axle: - 2 x 5.5 t Gigant axles Suspension: - Parabolic springs with tandem equalizer unit Drawbar / Drawbar Eye: - Height-adjustable (300 mm) hot-dip galvanized drawbar with 40 mm flange drawbar eye Electrics / Lighting: - Tire Pressure Monitoring System (TPMS) - 15-pin electrical connector - LED tail lights General Attachments: - Jost mechanical landing gear, front - 2 mechanical hot-dip galvanized folding supports, rear - Toolbox made of galvanized sheet steel, right side - Hot-dip galvanized bolted underrun protection - Toolbox made of galvanized sheet steel, right side - Plastic quarter mudguards Tipper Platform: - Mesh hooks on the sides and rear at the central locking mounts, plus 3 on the front wall - Hot-dip galvanized chassis - Steel pallet 3-way tipper body - Continuous side walls, foldable without center stanchions, with drop side spring assist - Tailgate foldable and swingable via manual central locking - Bolted hot-dip galvanized rear stanchions - 4 mm steel floor plate - Preparation for later retrofit of side wall extensions - Platform length: 5.5 meters Load Securing: - Each corner with 1 x 5 t lashing point - Each side with 4 x 3 t lashing rings recessed in the outer frame Ramps: - Mounting rail at rear for loading ramps - 1 pair aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles - Lockable storage compartment under the load platform, integrated into the chassis from the rear Wheelbase: - Wheelbase: 990 mm Tyres: - Tyres: 235/75R17.5 Paintwork: - Axles, springs, air tank, drawbar, and landing gear painted in black - Platform body color: RAL 9010 pure white - Painting of side walls and tipper platform in a different RAL color possible at extra cost Information: - Reinforced body with EN 12642 XL load securing certificate - New vehicle without initial registration with manufacturer’s warranty - Subject to errors and prior sale Delivery Time: - Available immediately ex stock Egestorf (A7)

Durumu: yeni, azami yük ağırlığı: 8.620 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.500 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2024, * KA-TA-R 11.9: ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axles ----Suspension: * Parabolic springs with tandem balance unit ----Drawbar / Flange Eye: * Hot-dip galvanized, height-adjustable drawbar (300 mm adjustment) with 40 mm flange towing eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin power connector * LED tail lights ----General attachments: * Jost mechanical landing leg at the front * Two rear mechanical, hot-dip galvanized folding supports * Tool box made of galvanized sheet steel, mounted on the right side * Bolted hot-dip galvanized underrun guard * Plastic quarter mudguards Nkodpel Thx Esfx Afgju ----Tipper body: * Mesh hooks on the sides and rear in the central locking mounts, plus three on the front wall * Hot-dip galvanized chassis * Steel pallet – 3-way tipper body * Continuous, fold-down side walls without central stanchions, fitted with drop-side spring lifts * Tailgate foldable and swinging, controlled via manual central locking * Hot-dip galvanized bolted rear stanchions * 4 mm steel floor plate * Preparation for subsequent installation of side wall extensions * 5.5-meter-long body ----Load securing: * 1 x 5 t lashing point in each corner * 4 x 3 t lashing rings recessed into the outer frame on each side ----Ramps: * Rear ramp rails for loading ramps * 1 pair of aluminum ramps, approx. 3,310 x 400 mm (8 t capacity per pair), suitable for rubber-tired and tracked vehicles * Lockable rear storage compartment beneath the platform, integrated into the chassis ----Wheelbase: * Wheelbase: 990 mm ----Tyres: * Tyres: 235/75R17.5 ----Paintwork: * Axles, springs, air tanks, drawbar, and landing leg painted in black * Body paintwork: RAL 9010 pure white * Painting of side walls and tipper body in any other RAL colour available at extra cost ----Additional information: * Reinforced body with EN 12642 XL load securing certificate * New vehicle without first registration, with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available immediately from Egestorf on the A7

Durumu: kullanılmış, azami yük ağırlığı: 28.700 kg, toplam ağırlık: 40.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 09/2013, bir sonraki muayene (TÜV): 09/2026, toplam genişlik: 2.550 mm, Donanım: ABS, Web sitemizde hemen ve kısa vadede temin edilebilen tüm araç stokumuzu bulabilirsiniz. Donanımın özeti. Tüm donanım bilgisi talep üzerine sunulur. * Kazıcı kepçesi, yaklaşık 2.800 x 770 x 280 mm * 2 parçalı hidrolik rampalar, yaklaşık 2.100 x 2.100 x 700 mm, hidrolik olarak kayar Nkedpfx Aex Tx Elsfgju * Hidrolik arka destekler * Hidrolik kaldırma yatağı, yaklaşık 4.020 mm uzunluğunda * Kısmen yükleme alanı ve rampalarda kauçuk kaplama * Rampalar için geçiş sacı * Yükleme alanı genişletilebilir * Wabco Smartboard * Yükseltme ve alçaltma fonksiyonlu havalı süspansiyon * Rampalarda 2 adet çalışma projektörü * Çekiciye hidrolik bağlantılar * 15 kutuplu elektrik + ABS * 50 mm çeki halkası * BPW akslar * Ahşap kaplamalı kuğu boynu * Kuğu boynuna entegre kapaklı depolama kutusu

Durumu: yeni, azami yük ağırlığı: 14.400 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system (TPMS) * Emergency release device for spring-actuated cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lift and lowering device * Drawbar with 50 mm flange towing eye and height adjustment of 110 mm by offset plate * Jost landing gear at front * External folding supports at rear * Plastic toolbox, approx. 750 x 350 x 300 mm, on right side * Lateral underrun protection * Plastic quarter mudguards * 15-pin electrical connector * Multi-chamber tail lights * Reinforcement package for drilling rig transport on chassis * 50 mm softwood floor, clamped design * Preparation in front of bulkhead for retrofitting container locks * Bolted front wall made of smooth panel * Split side walls made of trapezoidal-profiled steel sheet, foldable, with central folding stanchion * Steel rear wall, can be slid in between ramps—bracket for stowage when not in use, mounted inside front wall * Rear stakes bolted * Perforated outer frame, approx. 45° bent with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings possible every 600 mm * Lashing package: in each corner front and rear 1 x 10 t UVV lashing ring, on each side 2 x 8 t UVV retractable lashing rings in outer frame, multiple holes in front and rear cross beam for 1.2 t lashing possibilities * One-piece slide-in ramps, 12 t per pair, approx. 2,750 x 620 mm * Rear approach slope approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports and access ramps hot-dip galvanized * ---Axles, air tanks, flange towing eye and landing gear painted black--- * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm * Wheelbase: 1,810 mm * Tyres: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty Nedpomi Tmaefx Afgoku * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 14.400 kg, toplam ağırlık: 19.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lifting and lowering system * Tow bar with 50 mm flange eye and height adjustment of 110 mm via offset plate * Jost landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical socket * Multi-chamber tail lights Nksdjmi Tcqjpfx Afgou * Reinforcement package on chassis for drill rig transport * 50 mm softwood floor in clamped version * Pre-fitted equipment for retrofitting container locks in front of bulkhead * Bolt-on bulkhead made of smooth sheet metal * Split side walls, steel sheet - trapezoidal profile - foldable with central folding stake * Rear wall, steel, slide-in type between ramps - bracket for storage in front of bulkhead when not in use * Rear stakes bolted * Perforated outer frame approx. 45° angle, with 2 t lashing capacity every 480 mm * Option to install 3 t drop-forged lashing rings every 600 mm * Load securing package (Lasi): front and rear corners each equipped with 1 x 10 t UVV lashing ring, sides each with 2 x 8 t UVV retractable lashing rings in outer frame, multiple holes in bulkhead and end crossmember for 1.2 t lashing points * One-piece slide-in ramps, 12 t / pair, ramps approx. 2,750 x 620 mm * Rear access ramp approx. 860 mm * Chassis, tow bar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * ---Axles, air tanks, flange eye and landing gear painted in black--- * Unladen loading height approx. 940 mm * Laden loading height approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 8.800 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.370 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release device for spring-actuated cylinders * Drum brakes, 2 x 5.5 t ----Axles: * Gigant axles ----Suspension: Nksdpfx Afsl Th Nrsgsu * Parabolic springs with equalizing unit ----Towing Eye / Flange Tow Eye: * Towing bar adjustable in height by 300 mm * 40 mm flange tow eye ----General Attachments: * Jost landing gear front * Exterior folding support legs at the rear * Plastic toolbox, front right, mounted externally on the front wall * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * LED lighting ----Loading Platform: * Loading platform 5.37 m * 50 mm softwood floor * Bolted front wall made of smooth sheet metal * Drop sides made of trapezoidal-profiled steel, foldable with drop side spring assist * Steel rear wall, slide-in panel between ramp holders - stowed in front of the front wall when not in use * Rear stakes bolted ----Load Securing: * Perforated outer frame, angled approx. 45 degrees with 2 t lashing capacity at 480 mm intervals * Option to equip with 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing ring in each of the front and rear corners * Various holes for 1.2 t lashing options in the front and rear crossmembers ----Ramps: * One-piece mechanical grating access ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be compacted to 20 mm) * Approach slope at the rear approx. 860 mm chassis height ----Tyres: * Tyres 235/75 R 17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, front wall, tailgate, folding supports, and access ramps hot-dip galvanized * Axles, springs, air tanks, 40 mm flange tow eye painted in black * Sideboard painted RAL2011 deep orange * Painting of side panels in any RAL color available at extra cost ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 8.870 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 11.9: ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle assembly ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Towing Eye: * Drawbar with 300 mm adjustable height * 40 mm flanged towing eye ----General Attachments: * Jost mechanical landing gear at front * Externally mounted, hot-dip galvanized folding supports at rear * Side underrun protection * Plastic quarter mudguards * Plastic toolbox, front right, mounted externally on the front wall ----Electrics / Lighting: Nedpsl Thy Rofx Afgeku * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector * LED tail lights ----Cargo Area: * 50 mm softwood floor * 20" container locks mounted at front and rear * Bolted smooth sheet steel front wall * Drop sides made of trapezoidal steel sheet, foldable, with drop-side spring assist * Hot-dip galvanized, bolted rear stanchions ----Load Securing: * Perforated external frame, approx. 45-degree bent, with 2 t lashing capacity every 480 mm * Option to install 3 t swing lashing rings every 600 mm (5 lashing rings mounted on each side) * One 6.3 t lashing ring in each of the four corners front and rear * Various holes in the front and rear crossmembers for 1.2 t lashing options ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tyred and tracked vehicles * Rear access, storage compartment below loading platform integrated into the chassis ----Paintwork: * Hot-dip galvanized chassis as well as drawbar, front wall, rear wall * Dropside colour in RAL 9010 pure white * Painting of sidewalls in an RAL colour at additional cost possible ----Information: * New vehicle, unregistered * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Durumu: yeni, azami yük ağırlığı: 8.800 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.370 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-R 11.9: ----Braking System: * EBS brake system * Emergency release system for spring brake cylinders * Drum brakes, 2 x 5.5 t ----Axles: * Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Eye: * Height-adjustable drawbar, 300 mm range * 40 mm flange towing eye ----General Attachments: * Jost landing gear at the front * External foldable support legs at the rear * Plastic toolbox, front right, mounted externally on the front bulkhead * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ (tyre pressure monitoring) * LED lighting ----Loading Platform: * Loading length 5.37 m * 50 mm softwood floor * Bolted front bulkhead made of smooth sheet steel * Drop sides made of trapezoidal profiled steel, foldable, with drop side spring assist * Rear wall made of steel, can be slid between the ramp holders forward of the bulkhead when not in use * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * One 6.3 t lashing ring in each front and rear corner * Various holes in front and end crossmembers for 1.2 t lashing options ----Ramps: * One-piece mechanical steel grating ramps with spring assist for single-person operation, approx. 2,750 x 600 mm (can be compressed to 20 mm) * Approach slope at rear approx. 860 mm chassis height ----Tyres: * 235/75 R 17.5 tyres ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, bulkhead, tail gate, support legs, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flange towing eye painted black Nkjdpol Th Ncefx Afgou * Drop sides painted in RAL2011 deep orange * Sides can be painted in any RAL color at extra cost ----Information: * New vehicle with manufacturer's warranty * Subject to prior sale and errors ----Delivery Time: * Available immediately ex works Egestorf

Durumu: yeni, azami yük ağırlığı: 8.870 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.270 mm, yükleme alanı genişliği: 2.470 mm, yükleme alanı yüksekliği: 400 mm, Üretim yılı: 2025, * ETÜ-TA-ER 11.9: ----Braking System: * Electronic brake system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle assembly ----Suspension: * Parabolic springs with compensating unit Nksdpfx Afsl Tilxjgsu ----Drawbar / Flange Eye: * Drawbar adjustable in height by approx. 300 mm * 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Side underrun protection * Plastic quarter mudguards * Plastic toolbox, front right, mounted exterior on bulkhead ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin power connector * LED tail lights ----Cargo Area: * 50 mm softwood floor * 20" container locks, mounted at front and rear * Bolted smooth sheet steel bulkhead * Drop-down trapezoidal profile steel side walls with spring-assisted wall lifters * Bolted, hot-dip galvanized rear stakes ----Load Securing: * Perforated outer frame, bent at approx. 45°, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing brackets every 600 mm (5 lashing rings fitted on each side) * 1 x 6.3 t lashing ring at each front and rear corner * Various boreholes in the bulkhead and rear cross-member for 1.2 t lashing options ----Ramps: * 1 pair of aluminum approach ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Rear-accessed storage compartment for ramps, integrated under the loading area within the chassis ----Paint / Finish: * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * Drop side color RAL 9010 pure white * Side wall painting in a RAL color of your choice available at extra cost ----Information: * New vehicle without registration * Subject to errors and prior sale ----Delivery Time: * Available immediately ex Egestorf

Durumu: yeni, azami yük ağırlığı: 8.780 kg, toplam ağırlık: 11.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 5.000 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 500 mm, Üretim yılı: 2024, * KA-TA-R 11.9 Masterline: ----Braking System: * EBS brake system * Emergency release mechanism for spring brake cylinders * Drum brakes Nodpfopk D D Uex Afgsku ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Towing Eye: * Height-adjustable, hot-dip galvanized drawbar (adjustable by 300 mm) with 40 mm flange towing eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding support legs at the rear * Toolbox made from galvanized sheet steel on the right side * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin power connector * Bolt-on underrun protection with LED rear lights ----Tipping Platform: * Mesh hooks on the sides and rear in the central locking bearings, plus 3 on the outside of the front panel * Hot-dip galvanized chassis * Fully galvanized steel three-way tipper body * Continuous side walls, foldable without central stanchion, equipped with drop-side spring assistors * Rear tailgate foldable and swinging via manual central locking * Hot-dip galvanized, bolted rear stanchion ----Load Securing: * 1 x 5 t recessed and foldable lashing point in each corner, plus 4 x 3 t recessed and foldable lashing rings per side in the outer frame * 4 mm steel floor, ramp mounting rail at the rear for drive-on ramps ----Ramps: * 1 pair of aluminium loading ramps, approx. 3,570 x 400 mm (load capacity 8 t per pair), suitable for vehicles with rubber tires or tracks * Lockable rear storage compartment recessed in the chassis beneath the loading area ----Tyres: * 235/75 R 17.5 tires ----Paintwork: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle hot-dip galvanized ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf, near the A7