Kullanılmış Faymonville Stn Yarı Römorklar satın al (208)

Durumu: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, 3-axle MULTIMAX *PLUS low bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: * Loading platform width approx.: 2,540 mm Load height at max. payload approx.: 890 mm Suspension stroke approx.: -55/+145 mm Axle spacing: 1,360 mm *Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific regulations are exceeded. Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform, length approx. 9,600 mm with rear bevel approx. 900 mm x 6°. Loading platform behind gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating surface. Hydraulically foldable ramp tips. Ramps are individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward. Maximum load and approach angle as per technical data sheet: C470319 Maximum ramp angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift and lower valve. Axle tools. Crsdpfoizu Ntjx Ab Uoh Tyres: 235/75 R 17.5 3PMSF dual tyres. Manufacturer at our discretion. Load index 143/141J (144/144F) Brake system: WABCO EBS-E braking system according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" configuration according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation). Entire steel structure shot-blasted, then hot-dip refined with ZINACOR 850 (zinc 85% - alu 15%). Painting 6-coat final treatment: Whole steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion promoter. Topcoat with 2 layers of 2-component (acrylic) paint, single-color to RAL palette as chosen, followed by sealing the cavities with special wax. Rims in silver. Multi-color and custom painting available at extra charge. Steel construction: High-strength fine-grained steel construction. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa). Welders certified to DIN EN 287-1. MAG welding process per EN ISO 4063. Shielding gas M21 per EN ISO 14175. Front wall made of steel, removable, approx. 400 mm high. Connection panel for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. 24N connection as per ISO-1185 24S connection as per ISO-3731 15-pin connection as per ISO-12098 If your pin assignment differs from the ISO standard, please inform us. "Anderson" socket on the front connection panel. Rema 78051-00 & Amp. 150 V. Cable for electric-hydraulic unit and/or electric winch (

Durumu: iyi (kullanılmış), dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 156.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 250 mm, ilk tescil: 12/2002, süspansiyon: hava, Üretim yılı: 2002, Donanım: ABS, hidrolik arka platform, = Additional Options and Equipment = - Air suspension = Further Information = Axle Configuration Suspension: Air suspension Rear axle 1: Twin tires; Steered Rear axle 2: Twin tires; Steered Dimensions Dimensions (L x W x H): 15680 x 254 x 25 cm Weights Unladen weight: 11,040 kg Payload: 22,000 kg Gross vehicle weight: 33,040 kg Condition Technical condition: good Visual condition: good Financial Information Crjdpfsuyud Nox Ab Ueh Price: On request Additional Information Please contact David F Middelman or David F Middelman for more information.

Durumu: kullanılmış, toplam ağırlık: 65.000 kg, azami yük ağırlığı: 42.400 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 06/2006, toplam genişlik: 2.750 mm, toplam yükseklik: 3.900 mm, Donanım: ABS, Faymonville 4-axle lowbed trailer with removable swan neck, extendable, and 4 steering axles Type: STBZ-4WAUB Year: 2006 - Extendable up to a total length of 26 meters - Equipped with hydraulic ramps - 4 steering axles with remote control We are also happy to assist you with financing/leasing through our partners. All information without guarantee. Subject to errors and prior sale. Crsdpfx Aowuhm Isb Ueh

Durumu: kullanılmış, toplam ağırlık: 47.000 kg, azami yük ağırlığı: 33.980 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.850 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 350 mm, ilk tescil: 02/2022, Üretim yılı: 2022, toplam genişlik: 2.540 mm, toplam yükseklik: 2.300 mm, Donanım: ABS, Low-bed trailer with external beams in extendable SUPER LOW design, approximately 6,850 mm long * Total length extendable from 13,500 mm to 19,000 mm * Loading platform width extendable from 2,540 mm to 3,000 mm * Low-bed with fixed hardwood floor (approx. 40 mm thick) and mechanical locking * Supply lines are securely routed within the extendable beams and automatically adapt to the respective bed length * 5 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting of bolted RUD rings Rear Chassis * Rear chassis with closed outer frame, checker plate covering, and continuous prism-shaped excavator trough, approx. 1,250/700 x 505 mm, open at the rear * 2 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings lying inside the trough (LC 8,000 daN + 5,300 daN) * 2 pairs of stake pockets for plug-in stakes, approx. 100 x 50 mm, on the outer frame Gooseneck * Gooseneck in SNT design to optimize loading area length, approx. 3,785 mm long * Gooseneck hydraulically liftable/lowerable and detachable * Technical fifth-wheel load: 23,000 kg, suitable for tractors: 4x2, 6x2, and 6x4 PENDLE AXLE * All axles hydro-mechanically forced-steered * Burst protection valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and pre-insert for securing in raised position * Technical axle load: 12,000 kg each * Hydraulic axle compensation * Axle tools * Tyres: 245/70 R 17.5 3PMSF, load index (146/146F), new spare wheel Brake System * Brake system according to EU regulations with EBS-E (2S2M) with linkage to the tractor unit Electrical System * Remote control for axle steering * Electrical system in accordance with EU regulations * 24V ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK UNIBOX at the front connection strip with 24N, 24S, & 15-pin sockets according to ISO 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel Construction * High-strength fine-grain steel construction Quality grades: S355J2+N/S355MC Paintwork * Premium and durable corrosion protection * High-quality 2-component (2K) single-colour topcoat * 2'' king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip Csdpjwla Rtefx Ab Usrh * 4 wheel chocks with holders * Electro-hydraulic power unit * Yellow reflector tape in accordance with EU regulations on the sides, extensions, and rear of the trailer * Mount for beacon at the rear of the trailer including beacon light * European reflective boards (red-yellow) at the rear of the trailer * Mountings for warning signs, each with socket, on the gooseneck and rear left and right * User manual and documentation * 80 km/h speed stickers at the rear and both sides * Load gauge for axle load determination including load chart * Subject to errors, changes, and prior sale

Durumu: yeni gibi (kullanılmış), Fonksiyonellik: tamamen fonksiyonel, toplam ağırlık: 40.800 kg, boş ağırlık: 11.700 kg, azami yük ağırlığı: 29.100 kg, işletme ağırlığı: 24.300 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 16.500 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 500 mm, ilk tescil: 06/2008, süspansiyon: tam hava süspansiyonu, renk: gri, lastik boyutu: 235/75 R17,5, Üretim yılı: 2008, Donanım: ABS, For sale: boat gondola trailer in Spain with Swiss documentation, like new. 140,000 certified kilometers. - Hydraulic lifting neck Codpowva I Tefx Ab Usrh - Remote-controlled steering axles - 2 extensions (5m + 5m) = 6 + 5 + 5 = 16m low bed - Tyres at 90% tread

Durumu: kullanılmış, toplam ağırlık: 42.000 kg, azami yük ağırlığı: 30.389 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 03/2021, Üretim yılı: 2021, Donanım: ABS, 3-axle Faymonville MAX 100 telescopic low-bed trailer with gooseneck VIN: L0105526 Chassis / Attachments: * Air suspension // lift and lowering function * Gooseneck * 1 x self-steering trailing axle * Jost landing gear * 3 x BPW Eco Plus axles * Tyres: 205/65 R17.5 * Remaining tread depth: 1st axle approx. 90% // 2nd axle approx. 20/30% // 3rd axle approx. 30% * NATO plug * 4 x Bawer stainless steel toolboxes * Rear support legs Body: * Low-loader * Widening panels front and rear * Extendable to 6.3 m * Can be widened by approx. 20 cm per side * 12 x heavy-duty lashing rings per side * 1 x load pressure gauge * 8 x stake pockets on each side * Hydraulic ramps, width-adjustable * 2 x Altec aluminium ramps * 9 x side extensions on each side * Extendable by 6,100 mm * Gooseneck length 3,850 mm * Coupling height loaded: 1,150 mm * Loading height at max. load: 860 mm * Front toolbox Weights: * Gross vehicle weight: 42,000 kg * Unladen weight: 11,611 kg * Payload: 30,389 kg Other: * German vehicle * 1 previous owner * Technical inspection (HU) / safety inspection (SP) valid until 08/2025 New main inspections / safety inspections or (re)rating of weights are possible upon request. We are happy to assist you in obtaining export/temporary licence plates, and can also arrange delivery of your purchased vehicles within Germany. Contact us! We speak the following languages: German, English and Russian! No liability for printing or typing errors, changes, prior sale or mistakes excepted! Who are we? Cjdpewibbuofx Ab Uorh Leible Nutzfahrzeuge is a family business based in Kehl am Rhein. With many years of experience in the preparation and sale of commercial vehicles, we are a reliable partner for customers worldwide. Our particular strength lies in selling new and used commercial vehicles. On 11,000 m² you will find a large selection of vehicles. Our company philosophy is based on fairness and integrity. Customer satisfaction is our highest priority, so we offer our customers an excellent all-round service package and provide them with a competent contact person to assist with the purchase or sale of vehicles. See for yourself! Our services for you: Loading vehicles We are happy to help you load your purchased vehicles. Arranging special transports We are happy to assist with organising special transports. Day plates / export licence plates We are happy to assist with obtaining export/short-term licence plates. Customs formalities We are happy to assist you with customs matters.

Durumu: yeni, toplam ağırlık: 47.000 kg, azami yük ağırlığı: 34.104 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2025, Further information here: Credpfov D Abgox Ab Ueh

Durumu: mükemmel (kullanılmış), dingil konfigürasyonu: 3 dingil, ilk tescil: 02/2018, süspansiyon: hava, Üretim yılı: 2018, Axle configuration Suspension: Air suspension Rear axle 1: Max. axle load: 10,000 kg; Steering Rear axle 2: Max. axle load: 10,000 kg; Steering Rear axle 3: Max. axle load: 10,000 kg; Steering Dimensions Dimensions (L x W x H): 13,600 x 254 x 105 cm Weights Unladen weight: 10,000 kg Payload: 41,600 kg Gross vehicle weight (GVW): 51,600 kg Functionality Extendable body: Yes Maintenance, history and condition APK (Periodic Technical Inspection): valid until 06/2026 Technical condition: very good Visual condition: very good Financial information Csdpswr T R Tjfx Ab Uorh Price: On request Further information For further information, please contact David F Middelman.

Durumu: yeni, toplam ağırlık: 66.000 kg, boş ağırlık: 17.250 kg, azami yük ağırlığı: 48.700 kg, işletme ağırlığı: 17.250 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 375 mm, renk: gri, lastik boyutu: 245/70 R 17.5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized load platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Suitable for tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: - Low bed with external beams, configured as a telescopic vessel bridge in low construction with extension at the front - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Tread plate covering and continuous prismatic excavator recess approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Final coating of axles with 2 layers of single-colour 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps with climbing strips and fixing bolts for bridging the low bed uptake hooks - Ramps can be placed over or between the hooks - Mounting points for steel loading ramps at the rear between the external beams of the gooseneck - One locking position approximately every 1,000 mm on the extension - 1 lashing ring each left and right on the front cross member - Supply line connection strip to the tractor unit, fitted at the height of the outer frame profile - 6 pairs of threaded blocks on the outside of the inner beams of the load platform for mounting screw-on M24 rings - 6 pairs of recessed lashing rings on the outside of the outer beams of the load platform, foldable inwards and outwards - 1 pair of threaded blocks at the front and rear of the outer beams of the load platform for mounting screw-on M24 rings - Insertion strip for loose ALU approach ramps on the rear cross member of the vehicle Cedpfx Aboh Hm Tze Uerh - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering from front and rear, operable via cable remote control, with single-track control of axles - 3 kW electro-hydraulic power pack for operating hydraulic functions, except hydraulic winches - Removable load floor (galvanised), can be inserted in 3 elements between the outer beams, with hardwood covering - Folding extensions, approx. 230 mm per side - Loose widening boards, framed in steel - 4 warning panels approx. 423 x 423 mm - Radio remote control for remote steering operation - 3.5" kingpin - Anti-slip stickers on the left bevel of the gooseneck - Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings - Guiding plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning panels when not in use - 2 pairs of stanchion pockets recessed in the outer frame of the chassis for insertable stanchions approx. 100 x 50 mm - Rear section of the chassis with a detachable plate closing the bucket arm recess at the rear - Trailer colour MB 7350 Novagrau

Durumu: yeni, toplam ağırlık: 45.000 kg, boş ağırlık: 8.300 kg, azami yük ağırlığı: 36.700 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.080 mm, süspansiyon: hava, renk: gri, lastik boyutu: 385/65 R 22.5, Donanım: ABS, hidrolik arka platform, Loading Area: Loading area, extendable design with pneumatically operated locking mechanism Cut-outs in the outer frame of the loading area for securing straps to be hooked in Landing Gear: JOST landing gear (mechanical) with 2-speed gearbox for 24t lifting capacity Axles and Tyres: BPW axles, air-suspended, with disc brakes (430 mm), equipped with raise/lower function Trailing steering axle with electro-magnetic reversing lock, activated via reverse gear or manually Axle tool kit Tyres: 385/65 R 22.5 Brake System: WABCO brake system compliant with EU regulations, with EBS-E Paintwork: Crodpeikyh Hsfx Ab Ujh Superior and durable corrosion protection for the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc-rich primer High-quality two-component top coat, single-tone in MB 7350 Novagrau tail section metallized and painted in RAL 9010 Metallic paint not possible Steel Construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N / S355MC S690QL / S700MC Electrical System: Electrical system according to EU regulations 24 Volt ASPÖCK-NORDIK lighting ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets Connections according to ISO Accessories Included: Front galvanized connection strip with yellow-red air couplings Galvanized steel front bulkhead approx. 1,600 mm high, EN12642-XL 4 wheel chocks with brackets White reflective tape on the sides, on the extension, and rear red tape according to EU regulations European reflector plates at the rear of the trailer Approx. 30 mm thick hardwood floor, enclosed in omega profiles 10 pairs of stake pockets for 100 x 50 mm insert stakes in the outer frame 1 spare wheel carrier beneath the loading area, right side (in driving direction) Manual and operating instructions Bracket for rotating beacon at the rear of the trailer On the gooseneck and rear plate, left and right: bracket for warning signs including socket outlets Central chassis with painted sand coating as anti-slip protection 6 pairs of WADER container pockets in the loading area: for 1x 20ft container, 2x 20ft containers, or for 1x 40ft container in the extension, an additional locking point is provided for a 45ft container 4 pairs of crosswise stake pocket strips mounted in the loading area, for insert stakes 100 x 50 mm One galvanized crosswise bracket underneath the loading area, 2,390 x 720 x 400 mm Access ladder mounted on the right (in driving direction) Lifting axle on the front axle with TEBS E control, depending on the current axle load and current loading status Load gauge for determining axle loads, including load chart HRM metallization of the outer frame: Complete steel construction blasted, then defined visible areas metallized with ZINACOR 850 hot finish

Durumu: yeni, toplam ağırlık: 76.500 kg, boş ağırlık: 15.420 kg, azami yük ağırlığı: 61.080 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 900 mm, renk: gri, lastik boyutu: 235/75/r17,5, Donanım: ABS, Gooseneck: Gooseneck with rear bevel approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Load area: Extendable load area with rear bevel approx. 500 mm x 8° 8 pairs of outward folding lashing rings 1 pair of flat-fitted lashing rings at the front of the load area Recesses in the outer frame of the loading area for attaching tie-down straps Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Two-piece steel ramps: One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramp sections hydraulically lift and fold, hydraulically height-adjustable, and hydraulically shiftable. Maximum load per pair: 50,000 kg. Landing legs: • JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tires: BPW axles and suspension, 4th and 5th axles steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lockout, activated via reverse gear and manually Tires 235/75 R 17.5 3PMSF Braking system: Braking system according to EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector rail with sockets 24N, 24S & 15 pin Connection compliant with ISO: 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer High-quality 2-component (2K) topcoat, single color MB 7350 Novagrau Rear part metalized and painted in RAL 9010 (pure white) No metallic paint possible Crodpsl Sl Izsfx Ab Ueh Steel construction: Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Accessories: One spare wheel with holder in front of bulkhead 2" kingpin One galvanized steel front wall, approx. 400 mm high Yellow-red air couplings mounted on the galvanized connector rail at the front 2 wheel chocks with holder on the front wall Bracket at rear of gooseneck for ALU drive-on ramps One holder for a rotating beacon at the rear of the trailer Galvanized supports beneath the rear bevel of the loading area White reflector tape according to EU regulations on the sides, extension, and rear in red Electro-hydraulic unit at rear under the loading area Mounts for warning signs with socket at the gooseneck and rear plate left and right Ramp control valves fitted to right-hand side of the trailer One mud flap at the rear of the trailer Manual and documentation on USB stick 3.5" kingpin supplied loose Plug-in ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm (LxH) Rear galvanized drop-in stakes are removable (structure length approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or 40' container 6 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area Galvanized extensions, extendable by approx. 230 mm per side Lifting axle on the front axle with control via TEBS E, depending on the current axle load and current loading condition Square cleats 20 x 20 mm every 200 mm on the outer frame of the loading area's bevel On the checker plates, above the kingpin and the loa...

Durumu: yeni, toplam ağırlık: 68.000 kg, boş ağırlık: 15.900 kg, azami yük ağırlığı: 63.500 kg, işletme ağırlığı: 52.100 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 12.700 mm, yükleme alanı genişliği: 2.740 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75/r17,5, Donanım: ABS, Gooseneck: Gooseneck in SNT design to optimize loading platform length, approx. 3,300 mm long, with rear taper approx. 1,000 mm x 10° Technical fifth wheel load: 23,000 kg For tractor units: 6x2, 6x4 and 8x4 Loading Platform: Telescopic loading platform, length approx. 9,400 mm, with rear taper approx. 500 mm x 10° A recess integrated into the platform and extending into the incline to accommodate the excavator bucket stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with tapered locking pins and reinforced locking positions; supply lines are routed safely inside the extendable beams and automatically adapt to the current platform length Axles and Tyres: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool 235/75 R 17.5 3PMSF twin tyres Load index 143/141J (144/144F) Two-part Steel Ramps: One pair of two-part steel ramps, approx. 4,350 mm long and 900 mm wide Hardwood covering Hydraulically folding ramp tips Ramps hydraulically adjustable individually: approx. 235 mm outward, approx. 215 mm inward Csdpfsmfqi Iex Ab Uerh Braking System: WABCO EBS-E brake system in compliance with EU regulations Sockets and Lighting: 24-volt lighting system Full Metallization: Complete HRM metallization with ZINACOR 850 for optimal corrosion protection Surface Treatment: Entire steel structure shot-blasted automatically after welding using a blast wheel Second blasting with corundum for optimal coating adhesion Final coating with two layers of two-component paint (single colour, Nova grey), then cavity sealing with special wax Rims in silver grey Steel Structure: Steel structure made from high-tensile fine-grained steels Steel grades: S355J2+N/S355MC, S690QL/S700MC Accessories: Plug-in steel front wall, approx. 400 mm high Connection strip for supply lines to the tractor unit Spiral cable for supplying the electro-hydraulic unit and/or electric winch between trailer and tractor unit with plug for electro-hydraulic unit for hydraulic control functions, except hydraulic winches Outer beam of gooseneck with mounting holes for bolted lashing rings First hole approx. 200 mm from the front, then every approx. 400 mm One mounting hole at the upper rear portion of gooseneck outer beam for a bolted lashing ring Approx. 40 mm thick hardwood flooring above the gooseneck, chequer plate over kingpin area Gooseneck guide plate for the saddle plate, approx. 500 mm wide Continuous hardwood flooring (approx. 50 mm thick) over the loading platform, interrupted between the axles Locking of the loading platform using welded conical locking profiles every 250 mm, including pre-tension plate Oblong holes for insertable and repositionable bridging elements: on the fixed section behind the gooseneck at the front of the platform 1 sliding intermediate table for the telescopic tube with large cross-section Operating valves for hydraulic ramps on right side of vehicle Central lubrication system with 1 pump, standard grease according to NLGI-2 Radio remote control for steering override operation, in addition to cable remote, with 2 indicator lights on receiver for one-track monitoring

Durumu: yeni, toplam ağırlık: 47.000 kg, boş ağırlık: 12.900 kg, azami yük ağırlığı: 34.100 kg, işletme ağırlığı: 12.900 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.850 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 350 mm, süspansiyon: diğer, renk: gri, lastik boyutu: 245/70 R 17,5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,750 mm long - Gooseneck hydraulically height-adjustable and detachable - Technical fifth wheel load: 23,000 kg - Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading Platform: - Low bed with external beams in extendable "SUPER LOW" design, length approx. 6,850 mm - Low bed with fixed hardwood floor approx. 40 mm thick and mechanical locking Rear Chassis: - Rear chassis with closed outer frame, checker plate covering and continuous prismatic excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings foldable outward - 1 pair of lashing rings lying in the trough - 2 pairs of stake pockets for plug-in stakes (100 x 50 mm) in the outer frame Pendulum Axle and Tires: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-insert to secure in lifted position - Final coating of axles with 2 layers of single-color 2K paint, painted in "FAY-Grey-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 245/70 R17.5 - TPMS (Tire Pressure Monitoring System) compliant with ECE R 141 Accessories: - Prepared for fitting of bolted container locking positions for 1x 20ft or 1x 40ft container on the external beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel - On the galvanized connection strip at the front: yellow-red air couplings - 4 wheel chocks - Remote steering front and rear operable via cable remote control with push buttons, including single-track monitoring of the axles - Hydraulic connections from gooseneck to low bed with multi-coupling instead of threaded couplings - Electro-hydraulic unit - White reflector tape on sides, extension and rear, according to EU regulations - European reflector panels (red-yellow) at the rear of the trailer - At the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting of bolt-on RUD rings VLBG-4 - Removable ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized plug-in posts are removable (body length approx. 2,560 mm) - Gooseneck at the upper rear area closed with a removable cover - 5 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading platform - Fold-out extensions, approx. 230 mm per side - 2 pairs of bolt-on RUD rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the low bed’s mounting hooks - Sanded layer painted on the loading platform as an anti-slip coating - Speed stickers 80 km/h on rear and both sides - Rear chassis’ bucket recess at the rear closed with a plug-in plate - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm - Radio remote control for the rear steering, in addition to the cable remote control, with indicator lights on the receiver as single-track monitoring - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determining axle loads Crsdohlz R Sjpfx Ab Ujh - HRM (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces hot-finished in metallization with ZINACOR 850 (Zinc 85% - Alu 15%)

Durumu: yeni, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 r 17.5 3pmsf, renk: gri, Donanım: ABS, Loading Platform: Crooked loading platform with rear slope approx. 500 mm x 8° Recess in the sloped area as well as extending into the loading platform to accommodate the excavator dipper stick (approx. 2365 x 750 x 235/290 mm (L x W x H)). Cjdpfeiziatsx Ab Uorh 4 pairs of folding lashing rings, foldable outwards (LC 5,000 daN) 2 pairs of folding lashing rings, foldable outwards (LC 10,000 daN) 2 pairs of flat lashing rings in the front area of the loading platform (LC 5,000 daN) 1 pair of flat lashing rings in the front area of the loading platform (LC 10,000 daN) Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Hardwood flooring approx. 48 mm thick, above the axles Checker plate covering Brake System: Brake system compliant with EU regulations, equipped with EBS-E (2S2M) and EBS spiral cable for the tractor unit Steel Structure: Steel structure made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and durable corrosion protection for the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer High-quality 2-component (2K) top coat in solid Novagrey Rear section metallized and painted in RAL 9010 (pure white) Metallic finish not possible Electrical System: Electrical system in accordance with EU regulations, 24 Volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX with 24N, 24S & 15-pin sockets Connection in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Axles and Tyres: BPW axles, air suspension, drum brakes, with raise/lower function Axle tools Tyres 235/75 R 17.5, 3PMSF One-Piece Steel Ramps: One pair of galvanized one-piece steel ramps approx. 3,000 x 800 mm with hardwood flooring approx. 48 mm thick Ramp with hydraulic lift mechanism and hydraulically adjustable Maximum load per pair: 40,000 kg Accessories Included: Turntable with a +/- 1750 mm long drawbar, with a towing eye (50 mm diameter) Coupling height 830-1,010 mm when loaded Spiral cable 15/2x7-pin Yellow-red air couplings One mud flap at the rear of the trailer Manual and documentation on USB stick Holder for rotating beacon at the rear of the trailer European reflective plates (red-yellow) at the rear of the trailer White reflective tape according to EU regulations on the side of the trailer and red at the rear Ramp control valves mounted on the right side of the trailer Galvanized supports under the slope of the loading platform Electro-hydraulic unit mounted at the rear under the loading platform Cover plates to bridge the open space between ramps and loading platform 4 wheel chocks with holders 6 pairs of stake pockets for 100 x 50 mm stakes in the external frame of the loading platform Four extendable warning signs (approx. 423 x 423 mm) extendable by approx. 400 mm, each with an LED position lamp Holder for rotating beacon mounted on the warning signs On the central beam, an integrated sand layer as slip protection 80 km/h speed stickers at the rear and on both sides Mounting of the individual ramps on the trailer HRM metallization (High Resistance Metallisation) of the external frame Complete steel structure shot-blasted, then defined visible surfaces metallised with ZINACOR 850 (zinc 85% - alu 15%) with hot finishing Extensions galvanized, extendable by approx. 230 mm per side 2 load gauges for determining axle loads including load diagram

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 12.300 kg, azami yük ağırlığı: 37.200 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava kaldıracı, renk: gri, lastik boyutu: 235/75 R17.5, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 30 mm thick hardwood flooring - 3 pairs of lashing rings Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Loading platform: - Loading platform with rear chamfer approx. 1,000 mm x 8° - Approx. 48 mm hardwood flooring, over the axles with checker plate surface Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering axle - Air suspension with lift and lower valve Crodpstvfkfofx Ab Ueh - Self-steering axle with electro-magnetic reverse lockout, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" king pin - One galvanized steel headboard - Yellow-red air couplings on the galvanized connection rail at the front - 4 chocks with holders on the headboard - Mounting at the rear of the gooseneck for ALU drive-on ramps - 3 height levels of aluminum planks - Galvanized folding supports under the chamfer of the loading platform - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized headboard with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - Roof brand "EDSCHA" sliding forward on ALU roof rail profiles, bolted to front and rear wall - 3 pairs of sliding stakes in the loading platform - Body rear left and right hydraulically extendable by approx. 750 mm - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm reserve length, with tension belts at spacing approx. 600 mm - Upper edge of structure approx. 3,960 mm high - Driving with open sliding roof is not permitted and will cause damage to the curtain - Cover plates for bridging the gap between ramps and loading platform - Electro-hydraulic unit at the rear, beneath the loading platform - At the gooseneck and at the ramps left and right each a bracket for warning panels incl. socket - Control valves for the ramps positioned on the right trailer side - 6 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform - Lift axle at the front axle - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm on the right in driving direction between the axles - On the checker plate on the gooseneck and loading platform, a painted sand layer for slip resistance - Central lubrication system BEKAMAX (Pico) with standard lubricant NLGI-2 and removable guard around the pump - Four warning panels extendable by approx. 400 mm, each approx. 423 x 423 mm, with position light - Load pressure gauge for determining axle loads including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then visible defined surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Durumu: yeni, toplam ağırlık: 102.000 kg, boş ağırlık: 22.700 kg, azami yük ağırlığı: 79.300 kg, işletme ağırlığı: 22.700 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 11.000 mm, yükleme alanı genişliği: 2.850 mm, yükleme alanı yüksekliği: 920 mm, renk: gri, lastik boyutu: 245/70 R 17.5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading deck length, approximately 3,750 mm long, with rear tapering of about 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6x4 and 8x4 Loading Platform: - Extendable loading platform, length approx. 11,000 mm with rear taper approx. 500 mm x 10° - A recess in the platform and into the taper for accommodating the excavator bucket arm, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking bolt and reinforced locking positions; supply lines are protected in the extendable beams and automatically adapt to the respective platform length Ramps: - One pair of two-part steel ramps, approx. 4,650 mm long and approx. 900 mm wide - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" rubber flooring 25 mm and approx. 5 mm steel flooring as additional reinforcement on the tapered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension and Tyres: - PA-X axle system, all axles forced steered hydro-mechanically - Steering behavior of the first two axles can be optimally adjusted to the platform length both mechanically and hydraulically - Hose rupture valve on the axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pilot pin for securing in raised position - 245/70 R 17.5 3PMSF Accessories Included: - Removable steel front wall, approx. 400 mm high - Supply line connection strip to tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of the gooseneck with mounting holes for screwable lashing rings - The first hole approx. 200 mm from the front, then spaced approx. every 400 mm Crsdpfxek Af Sve Ab Uoh - 2 pairs of screw-in lashing rings included - Checker plate covering over the gooseneck - 1 pair of removable ALU sideboards approx. 400 mm high, anodized, mounted on the gooseneck - Removable rear ALU wall on the gooseneck, approx. 400 mm high, anodized - 3.5" king pin / 2" king pin fitted - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - 4 wheel chocks - 4 axle load gauges - Mechanical fixed support legs at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical fixed support legs at the front - Continuous steel sheet flooring with painted-in sand layer on the platform for anti-slip protection - 1 intermediate table, approx. 500 mm wide, for the extending section, with elongated holes for suspended and adjustable bridging elements - Painted sand coating on the supporting surfaces of the intermediate table - Mechanical locking for securing the intermediate table in the extended position - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widening units approx. 230 mm per side - 1 pair of hydraulic rear supports - Central lubrication system - 1 reversing light each left and right at the rear of the vehicle - 3 kW electro-hydraulic power unit - Widening boards, loose, in reinforced steel U-frame - Radio and cable remote control - 4 warning panels, approx. 423 x 423 mm

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 11.400 kg, azami yük ağırlığı: 36.600 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.100 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 235/75 r 17,5, Donanım: ABS, Gooseneck: • Gooseneck in SNT design for optimised loading platform length, approx. 3,700 mm long. • Rear gooseneck with chamfer approx. 1,000 mm x 6°. • Technical fifth wheel load: 18,000 kg • Suitable for tractor units: 4x2 or 6x2 Loading platform: • Loading platform, length approx. 9,400 mm, with rear chamfer approx. 900 mm x 6°. • Platform area after the gooseneck, hydraulically liftable and lowerable. • Platform section length approx. 3,000 mm, load capacity up to 9,000 kg Ramps: • 1 pair of two-part hydraulic steel ramps, approx. 4,350 x 900 mm • Hardwood surface • Hydraulically foldable ramp ends • Ramps can be shifted individually by approx. 235 mm outward and approx. 365 mm inward hydraulically Axles and Suspension: • BPW axles and suspension, two rigid axles, one steering trailing axle • Technical axle load: 12,000 kg Cedpsiuy Npsfx Ab Usrh • Electromagnetic reverse lock, activated via reverse gear and manually • Air suspension with lift and lower valve • Axle tools Tyres: • 235/75 R 17.5 3PMSF twin tyres • Load index 143/141J (144/144F) Braking system: • Brake system by WABCO EBS-E in accordance with EU regulations Lighting system: • 24-volt lighting system in "ASPÖCK-NORDIK full LED" (ASS 3) • Design in accordance with EU regulations Metal finishing: • Standard HRM metallisation (High Resistance Metallisation) of the outer frame • Entire steel structure shot-blasted, then defined visible areas finished • Metallised with ZINACOR 850 (85% Zinc – 15% Aluminium), hot galvanised finish Paintwork: • 6-coat final treatment: • Complete steel structure shot-blasted after welding • One coat of zinc-based primer, followed by an adhesion primer • Final coating with two layers of 2-component (acrylic) paint in solid novagrau colour, followed by cavity sealing with special wax. Rims in silver. Steel Construction: • Steel structure made of high-strength fine-grained steel • Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) • Welders certified to DIN EN 287-1 • MAG welding process according to EN ISO 4063 • Shielding gas M21 according to EN ISO 14175 Accessories included: • Plug-in steel front wall, approx. 400 mm high • Connector panel for supply lines to tractor unit, mounted at height of outer frame profile • ASPÖCK-UNIBOX on front connector panel with 24N, 24S & 15-pin sockets - 24N connection according to ISO-1185 - 24S connection according to ISO 3731 - 15-pin connection according to ISO-12098 • 1 spare wheel with mounting adapter under the right side of the loading platform, in front of the axles • Parking position for warning plates on the gooseneck when not in use • Gooseneck outer beam with mounting holes for bolted lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) • One mounting hole on upper rear section of gooseneck outer beam for one bolted lashing ring. 1 pair of screw-in lashing rings included (LC 10,000 daN) • 1 pair recessed lashing rings rear centre of the gooseneck (LC 5,000 daN) • 3 pairs recessed lashing rings inside the outer gooseneck beam (LC 5,000 daN) • 3 pairs lashing rings in the centre of the gooseneck (LC 5,000 daN) • Approx. 40 mm hardwood floor above gooseneck • 2" king pin • On gooseneck, 1 pair plug-in aluminium side boards, approx. 400 mm high, anodised finish • On gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodised finish.

Durumu: yeni, toplam ağırlık: 60.800 kg, azami yük ağırlığı: 49.000 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 r 17.5, Donanım: ABS, Gooseneck: - Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable Loading Platform: - Loading platform in extendable design with rear taper approx. 1,000 mm x 8° - 5 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - c. 48 mm thick hardwood flooring, over the axles with checker plate covering Detachable Two-Part Ramps: - One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting unit and hydraulically adjustable - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles, two rigid axles, two steering trailing axles, air suspension, with drum brakes, with raise/lower function - The trailing steering axles can be locked electromagnetically via reverse gear or manually - Axle tools - Tyres: 235/75 R 17.5 Brake System: - Brake system according to EU regulations with EBS-E (4S3M) Steel Construction: - Steel construction made of high-tensile fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat finish in single-colour Novagrau Cjdpeh Etf Rjfx Ab Uorh Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front terminal strip with 24N, 24S & 15-pin sockets Accessories Included: - 2" king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings at the galvanized front terminal strip - 4 chocks with holder at the front wall - Mounting at the rear area of the gooseneck for ALU drive-on ramps - Galvanized folding supports under the taper of the loading platform - Bracket for a rotating beacon - Cover plates to bridge the gap between ramps and loading platform - White reflector tape to EU specification on the sides, red at rear and on extension - Electro-hydraulic power pack - On both sides of the gooseneck and ramps, mounting brackets for warning signs incl. socket outlet - Ramp control valves installed on the right trailer side - One mudguard at the rear of the trailer - Instruction manual and description on USB stick - ALU side walls and end wall, plug-in, on gooseneck approx. 2,440 x 400 mm - The rear galvanized plug-in posts are removable (length of structure approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, 2x 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Extensions, galvanized, extendable by approx. 230 mm per side - Lift axle on the front axle with control - Square climbing rails 20 x 20 mm - Central lubrication system BEKAMAX - F

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 9.300 kg, azami yük ağırlığı: 38.700 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.200 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 385/65 R 22,5, Donanım: ABS, Loading Platform: • Loading platform in extendable design with pneumatically operated locking mechanism • Loading platform with approx. 30 mm thick wooden floor • 7 pairs of outward-folding lashing rings (LC 5,000 daN) • 3 pairs of outward-folding lashing rings (LC 10,000 daN) • Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydro-mechanically forced steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with raise/lower valve • Axle tools • Tyres: 385/65 R 22.5 • TPMS (Tyre Pressure Monitoring System) according to ECE R 141 Brake System: • WABCO brake system compliant with EU regulations, with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin • Connections according to ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Accessories Included: • Remote-controlled steering from front and rear via cable remote with push-button operation, including single-track monitoring of axles • 4 wheel chocks with holders mounted on the front wall • 2" kingpin • One galvanized steel front wall approx. 1,600 mm high • Yellow-red air couplings mounted on the galvanized front connection bar Credpfx Abeiu Etro Ueh • White reflective tape according to EU regulations on the sides, at extension and at the rear of the trailer in red • European reflective plates (red-yellow) on the rear of the trailer • One mudflap at the rear of the trailer • Manual and description • Mounting bracket for a beacon at the rear of the trailer • Loading platform with approx. 30 mm thick wooden floor enclosed in omega profiles • 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform • 1 spare wheel holder under the right side of the loading platform in the direction of travel • Electro-hydraulic unit • On the gooseneck and rear apron left and right, each with a bracket for warning boards including socket • Painted sand layer for anti-slip protection on the main beam • 6 pairs of WADER container locks on the loading platform, for 1x20ft, 2x 20ft, or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container • 4 pairs of crosswise mounted stake pocket bars on the loading platform for plug-in stanchions 100 x 50 mm • Access ladder mounted on the right in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm in front under the loading platform on the left in the direction of travel • BEKAMAX central lubrication system (Pico) with removable pump guard • Lift axle on the front axle controlled by TEBS E depending on current axle load and loading condition • Wireless remote control for the rear steering in addition to the cable remote, with indicator lights on the receiver for single-track monitoring • Four extendable warning plates approx. 400 mm extension, size approx. 423 x 423 mm with position light • Bracket for beacon on the warning plates • 80 km/h speed stickers on the rear and both sides • Load pressure gauge to determine axle loads, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then the defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Durumu: yeni, toplam ağırlık: 63.000 kg, boş ağırlık: 15.550 kg, azami yük ağırlığı: 47.450 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long Cedpsk Aht Usfx Ab Uerh - Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator bucket arm - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood flooring on the bevel of the loading platform Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide - Ramps with hardwood covering - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - Square climbing strips 20 x 30 mm, at approx. 200 mm intervals on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, first axle steerable, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated automatically in reverse gear and manually - Air suspension with lift and lower valve - Tires: 235/75 R 17.5 twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS tire sensors installed in all wheels, including spare wheels Accessories included: - Detachable front wall, steel, approx. 400 mm high - 3kW electro-hydraulic power unit for operating hydraulic functions, except hydraulic cable winch - Parking bracket for warning signs on gooseneck when not in use - 1 spare wheel - On the gooseneck: 1 pair of detachable ALU side boards, approx. 400 mm high, anodized - On the gooseneck: one detachable ALU rear board, approx. 400 mm high, anodized - Over the gooseneck: approx. 40 mm thick hardwood covering, checker plate covering above king pin - 2'' king pin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with two-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Telescopic width extensions (galvanized) approx. 230 mm per side - Wheel recesses with square climbing strips - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering from front and rear via cable remote control, with single track axle monitoring - 1st axle with automatic lifting axle function - Central lubrication system with 1 pump, BEKAMAX brand - Wireless remote control for remote steering, in addition to cable remote, with 2 indicator lights on receiver for single track monitoring - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for beacon

Durumu: yeni, toplam ağırlık: 69.500 kg, boş ağırlık: 13.500 kg, azami yük ağırlığı: 51.500 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 r17.5, Donanım: ABS, Gooseneck: Gooseneck in SNT design for optimization of loading area length, length approx. 3,700 mm Gooseneck rear with bevel approx. 1,000 mm x 10° Loading Area: Telescopic loading area, length approx. 8,800 mm, with rear incline approx. 500 mm x 10° Recess in the incline and extending into the loading area for accommodating the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected within the extendable beam and adjust to the respective loading area length Ramps: 1 pair of two-piece steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically adjusted individually approx. 235 mm outwards and 215 mm inwards Cjdpfx Abok Ahuge Usrh Axles and Suspension: BPW axles and suspension, two fixed axles, two steering trailing axles Electromagnetic reverse lock activated via reverse gear and manually Air suspension with lifting and lowering valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO brake system, EBS-E according to EU regulations Lighting System: 24-volt lighting system, “ASPÖCK-NORDIK full LED” Metallization: Standard HRM metallization of the external frame Complete steel structure shot blasted, subsequently visible defined surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished Steel Structure: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified according to DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included accessories: Removable steel front wall, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 Round NATO socket on the front connection strip Cable for supplying the electro-hydraulic pump and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations (except for hydraulic winches) 1 spare wheel with mounting adapter External beams on the gooseneck with mounting holes for bolt-on lashing rings, first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included Mounting hole on the upper rear of the gooseneck external beam for a screw-on lashing ring 1 pair screw-in lashing rings Approx. 40 mm thick hardwood floor above gooseneck On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized On the gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodized 2" king pin Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 4 wheel chocks with holders Provision for aluminium approach ramps Mechanical landing gears with 2-speed gearbox and crank On the loading area, continuous hardwood floor approx. 50 mm thick, interrupted only between the axles Load area locking with conically welded positioning profiles every 250 mm including pre-tension plate Slotted holes at the front of the loading area for attachable and repositionable bridging plates 1 intermediate table with recessed loading area, approx. 300 mm wide, for the large cross-section sliding tube with sheet metal covering Front and rear with longe...

Durumu: yeni, toplam ağırlık: 49.500 kg, boş ağırlık: 10.350 kg, azami yük ağırlığı: 39.150 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava/hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of fixed built-in wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses equipped with 15 x 15 mm square climbing strips and lower-section extensions - 1 pair of fixed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm - 3-part removable galvanized covers over wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the ramp and extending into the load area to accommodate an excavator bucket arm approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings (LC 5,000 daN) Crjdpfeiu Er Aox Ab Uoh - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm depression (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece ALU ramps: - One pair of single-piece ALU ramps approx. 2,500 x 600 mm - Ramps with spring assist and manual lateral adjustment - Maximum load per pair: 24,000 kg Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tools - Tyres 235/75 R 17.5 - TPMS (Tire Pressure Monitoring System) in compliance with ECE R 141 Accessories included: - One spare wheel with bracket in front of the bulkhead - 2" kingpin - One galvanized steel bulkhead ca. 400 mm high - Yellow-red air couplings at the galvanized front coupling strip - 4 chocks with bracket at the bulkhead - Accommodation at the rear of the gooseneck for ALU approach ramps - Galvanized extensions, extendable approx. 230 mm per side - Galvanized folding supports under the rear incline of the loading area - Bracket for a rotating beacon at the rear of the trailer - White reflector tape in accordance with EU requirements on sides, red on extension and rear - On the gooseneck and rear panel, bracket for warning boards including socket, left and right - On the gooseneck, plug-in ALU side walls and rear wall approx. 2,440 x 400 mm - Removable rear galvanized stanchions (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area - One removable galvanized intermediate table with 1 pair WADER container pockets - 20 x 20 mm square climbing strips every 200 mm along the outer frame of the loading area's rear incline - Non-slip sand coating painted onto the checker plate on the gooseneck and loading area - Four warning boards extendable by approx. 400 mm each, approx. 423 x 423 mm with position light - Bracket for rotating beacon on warning boards - 80 km/h speed stickers on the rear and both sides - Load gauge for axle load determination including load chart - HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces metallically finished with ZINACOR 850 (Zinc 85% - Alu 15%) hot metalized

Durumu: yeni, toplam ağırlık: 45.000 kg, boş ağırlık: 9.500 kg, azami yük ağırlığı: 35.500 kg, işletme ağırlığı: 9.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.540 mm, süspansiyon: hava, renk: gri, lastik boyutu: 435/50 R 19.5, Donanım: ABS, Loading platform in extendable design: Loading platform with hardwood floorboards, rear chamfer approx. 1,000 mm x 8° 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm 2 pairs of lashing rings (LC 5,000 daN) 1 pair of lashing rings (LC 10,000 daN) 6 pairs of folding external lashing rings (LC 5,000 daN) 2 pairs of folding external lashing rings (LC 10,000 daN) Cut-outs in the outer frame of the loading platform for hooking in tensioning straps (LC 2,000 daN) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: Premium, durable corrosion protection for the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer High-quality single-color 2-component (2K) top coat in Novagrau Rear section metallised and painted in RAL 9010 (pure white) No metallic effect paint possible Crodpfek Eammox Ab Ueh Landing legs: JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting Sockets: 24N, 24S & 15-pin Axles and tires: BPW axles, air suspension, disc brakes (377 mm), with lift/lower function The trailing steering axles can be locked for reversing by electro-magnetic control via reverse gear or manually Axle tools Tires 435/50 R 19.5 Accessories included: At the front galvanized connection rail, yellow-red air couplings 4 wheel chocks with holders 2" king pin Galvanized steel front wall, approx. 1600 mm high, EN12642-XL White reflective tape to EU standards on the sides, on the extension, and red at the rear Loading area with heavy-duty hardwood flooring 9 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading platform 1 spare wheel holder under the loading platform, right side of direction of travel Galvanized drop-down supports under the loading platform chamfer Sliding hook-in strips for ALU loading ramps at the rear of the vehicle European reflective signs (red-yellow) at the rear of the trailer A mudflap at the rear of the trailer A bracket for a rotating beacon at the rear of the trailer On the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket 1 HDPE toolbox 620x360x610 under the loading platform, left side of direction of travel 4 pairs of WADER container locks in the loading platform for 1x 20ft container or 1x 40ft container; the extension is prepared with an additional locking position for a 45ft container 3 pairs of crosswise stake pocket strips mounted in the loading platform for 100 x 50 mm plug-in stakes Lift axle on the front axle with control via TEBS E depending on current axle load and load status Speed stickers 80 km/h at the rear and on both sides Four warning panels, extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light. Each warning panel with a bracket for revolving beacon Load gauge for determining axle loads including load chart HRM metallization (High Resistance Metallisation) of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces are metallised

Durumu: yeni, toplam ağırlık: 45.000 kg, boş ağırlık: 10.600 kg, azami yük ağırlığı: 35.400 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 940 mm, süspansiyon: hava, renk: gri, lastik boyutu: 235/75 R 17,5, Donanım: ABS, Loading platform: - Loading platform with extendable design - Loading platform with hardwood planks, approx. 500 mm x 8° rear chamfer - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading platform for attaching tension straps Brake system: - Brake system compliant with EU regulations with EBS-E (2S2M) Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) topcoat, single-color in Novagrau (Nova grey) - Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint not available Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel construction: - Steel construction made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Electrical system: - Electrical system according to EU regulations, LED lighting 24 Volt - Sockets: 2x 7-pin & 1x 15-pin Axles and tires: - BPW axles, air-suspended, with disc brakes (377 mm), with lift/lower function Crodpfxel Ux Rwj Ab Ueh - Hydro-mechanically forced steering - Axle tool kit - Twin tires 235/75 R 17.5 Included accessories: - Yellow-red air couplings on the galvanized front connection rail - 4 chocks with holders - 2" king pin - Galvanized steel front wall approx. 1600 mm high - White reflective tape as per EU regulations on sides, extension, and rear in red - Loading platform with heavy-duty hardwood floor - Steering from front and rear via cable - Remote control via push buttons with single-track axle monitoring - Radio remote control for auxiliary steering - 9 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform - Galvanized folding supports under the loading platform chamfer - Sliding hook-in rail for ALU ramps at the rear of the vehicle - European reflective signs (red-yellow) at the rear of the trailer - One mudflap at the rear of the trailer - One bracket for a rotating beacon at the rear of the trailer - On the gooseneck and on the left/right rear panel each: one holder for warning signs including socket - INOX toolbox 1,500 x 390 x 810 under the loading platform on the right (direction of travel) - BEKAMAX (Pico) central lubrication system with standard grease NLHI-2 and removable guard for the pump - 6 pairs of WADER container locks in the loading platform, for 1x 20ft container, 2x 20ft container, or 1x 40ft container, with additional locking point in the extension for a 45ft container - 4 pairs of cross-mounted stake pocket rails in the loading platform, for plug-in stanchions 100 x 50 mm - Lift axle at the front axle with TEBS-controlled adjustment, depending on current axle load and loading status - Speed stickers 80 km/h at rear and both sides - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, with LED position light - Holder for rotating beacon on warning signs - Load pressure gauge for axle load determination, including load diagram - HRM metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then defined visible areas hot-finished metallized with ZINACOR 850 (Zinc 85% - Alu 15%)

Durumu: yeni, toplam ağırlık: 48.000 kg, boş ağırlık: 11.300 kg, azami yük ağırlığı: 36.700 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.250 mm, süspansiyon: hava, renk: gri-siyah, lastik boyutu: 385/65 r 22,5, Donanım: ABS, Loading Area: Extendable loading platform with pneumatically operated locking mechanism A fixed intermediate table approx. 250 mm wide is mounted on the central beam 8 pairs of folding lashing rings (LC 5,000 daN) 3 pairs of folding lashing rings (LC 10,000 daN) Cut-outs in the outer frame of the loading area for hooking in tension straps (LC 2,000 daN) Axles and Tyres: BPW axles and suspension, all axles hydromechanically forced-steered Disc brakes, technical axle load: 10,000 kg Air suspension with lift and lower valve Axle tool kit 6 tyres 385/65 R 22.5 Brake System: Brake system according to EU regulations with EBS-E (2S2M) Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load) Steel Construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical System: Electrical system in line with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with 24N, 24S, and 15-pin sockets Connections per ISO: Csdpohlz Shsfx Ab Ujrh 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting: Top-class and durable corrosion protection of the standard shot-blasted welded frame provided by a 2-component (2K) zinc-rich primer High-quality 2-component (2K) top coat in single-colour Nova Grey Rear end metallised and painted in RAL 9010 (pure white) Metallic paint not available Included Accessories: One bracket for warning signs, each at the gooseneck and the rear end plate, left and right, including socket Remote steering operated from front and rear using cable remote control with push-buttons, with single-track alignment of the axles Electro-hydraulic power pack 4 wheel chocks with holder on the front bulkhead 2" kingpin One galvanised steel headboard approx. 2,200 mm high Yellow-red pneumatic couplings on the galvanised connection rail at the front White reflective tape per EU regulations on the sides, on the extension, and red at the rear European reflective warning plates (red-yellow) at the rear of the trailer One mud flap at the rear of the trailer Manual and documentation Bracket for revolving beacon at the rear of the trailer Loading surface with approx. 30 mm thick wooden floor embedded in Omega profiles 10 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading area 1 spare wheel holder under the loading platform on the right in the direction of travel 6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2x 20ft containers, or 1x 40ft container; an additional locking point in the extension is provided for a 45ft container 5 pairs of cross-mounted stanchion pocket rails in the loading area for plug-in stanchions 100 x 50 mm One galvanised bracket crosswise under the loading platform (2,390 x 720 x 400 mm) Entry ladder mounted on the right side in the direction of travel HDPE toolbox 1,200 x 500 x 480 mounted at the front under the loading surface on the left in the direction of travel Lifting axle on front axle, control by TEBS E depending on current axle load and load status Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 general-purpose grease and removable guarding around the pump Red/white reflective tape in the loading platform extension A sand layer painted on the central beam as anti-slip protection Radio remote control for rear steering in addition to cable remote, with in