Kullanılmış Faymonville Stbz Yarı Römorklar satın al (185)

Durum: yeni, azami yük ağırlığı: 36.500 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the specification list. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimized loading deck length, approx. 3,700 mm long, rear with chamfer approx. 1,000 mm x 6° * For tractors: 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX * Grating flooring with 5 mm steel reinforcement on gooseneck and rear chamfer * 2-inch king pin * Guide plate on the gooseneck for the fifth-wheel plate, approx. 500 mm wide * Round NATO socket at the front terminal strip (Maeler & Kaege VG 96 917) * On the gooseneck, one pair of removable side alu drop sides, approx. 400 mm high, anodized finish * One LED work light each mounted left and right at the top of the front wall, operated by on/off switch (operation from tractor unit not possible in this configuration) LOADING PLATFORM: * Loading platform, approx. 9,600 mm long, rear chamfer approx. 900 mm x 6° * Loading platform after gooseneck hydraulically liftable/lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg * Continuous grating flooring with approx. 5 mm steel underlay on lift bed and loading platform for additional reinforcement, designed for point loads TYRES: 235/75 R 17.5 3PMSF twin wheel configuration. Brand at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle self-steering * 3rd axle with electromagnetically operated reverse lock, activated via reverse gear and manually * 1st axle with traction help * Technical axle load: 12,000 kg each * Air suspension with lift-lower valve Kdsdpoy Auhhsfx Akqop HYDRAULIC LOADING RAMPS: * 1 pair two-piece AXS steel ramps with grating surface, approx. 4,920 mm long, approx. 900 mm wide * Hydraulically folding ramp tips * Ramps hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward independently * Flashing lights on outer side of ramp tips, switch located next to ramp controls * Transport lock for ramps using quick-lock mechanism * On-outline sand coating finish on ramp outer frame and ramp tips * Mechanical drop-leg supports on the sides of the ramps for aligning with unloading docks * Control valves for hydraulic ramps located on the right side of the vehicle BRAKING SYSTEM: WABCO EBS-E braking system, meets current EU requirements SURFACE PROTECTION: * HRM-metallization of full vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimum corrosion protection PAINTWORK: * Trailer in carmine red (RAL 3002) * Rims in silver grey * Side panels: natural aluminum * Wheel hubs per axle manufacturer * Lamp panel in pure white (RAL 9010) EQUIPMENT: * Front wall made of steel, removable, approx. 1,600 mm high, incl. connector plate for supply lines to tractor mounted approx. 1,000 mm from the lower edge of the outer frame * Lash chain securing points at inside front wall (left and right), with aluminum troughs below left and right for chain or ratchet strap storage * Behind front wall: approx. 12 mm thick DELIGNIT board bolted on * Two additional pairs of bolted lashing rings (LC 5,000 daN) * Electric cable winch, pulling force approx. 5,400 kg, with radio remote control. Steel cable approx. 24 m long, cable diameter approx. 9.5 mm, incl. cable feed guide.

Durum: yeni, azami yük ağırlığı: 30.190 kg, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 2 dingil, Donanım: ABS, You can find our full range of vehicles, including immediately and short-term available units, on our website. Excerpt from the Equipment List. Complete equipment details available upon request. Loading Platform: - Low bed with external beams, designed as extendable SUPER LOW version, approx. 6,850 mm in length - Low bed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking - Service lines routed securely inside the extendable beams, automatically adjusting to the respective bed length - 5 pairs of lashing rings, foldable to the outside (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD rings Gooseneck: - Gooseneck in SNT design for optimized loading length, approx. 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractor units: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed outer frame and checker plate cover - Chassis with excavator recess, closed in the rear half to accommodate air tanks - 2 pairs of lashing rings, foldable to the outside (LC 5,000 daN) - 1 pair of lashing rings, foldable to the outside (LC 10,000 daN) - 1 pair of lashing rings, horizontal, mounted at the front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles with hydro-mechanical forced steering - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve Tyres: - 245/70 R 17.5 3PMSF tyres - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system per ECE R 141 - Data transfer to the tractor via standardized EBS interface (ISO 11992) - The tractor must be capable of transmitting and displaying these data for correct indication Brake System: - Brake system compliant with EU regulations, with EBS-E (2S2M) Electrical System: - Electrical system compliant with EU regulations, 24-volt lighting ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the turn signal - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S, and 15-pin sockets according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Structure: - Made from high-strength fine-grained steels - Steel grades: S355J2+N / S355MC (yield strength 355 MPa), S690QL / S700MC (yield strength 690 MPa) Coating: - Complete steel frame automatically shot-blasted after welding - Second blasting treatment with corundum for optimal coating adhesion - HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for superior corrosion protection - Final topcoat: 2 layers of 2K paint, single color, RAL 3002 carmine red, in accordance with RAL system 841GL - Rims in silver - Rear section metallized and painted in RAL 9010 (pure white) - Metallic paint not available - Paint build-up tested in salt spray fog test according to ISO 9227-NSS - Cavity sealing with special wax Including the following additional equipment: - 2-inch king pin - One galvanized steel front wall, approx. 400 mm high Ksdpfjxarl Njx Akqsdp - Remote steering from front and rear, cable remote controlled via push buttons, with single-track steering alignment (installation in the tractor unit not included) - Hydraulic connections from gooseneck to low bed with multi-coupling instead of screw couplings - Electro-hydraulic power unit - Preparation for mounting of bolt-on container positions for 1x 20' or 1x 40' container on the external beams - Without container locks

Durum: yeni, azami yük ağırlığı: 36.040 kg, toplam ağırlık: 53.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Equipment excerpt. Full specification upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, approx. 3,750 mm long * Gooseneck hydraulically lift/lowerable and detachable * For tractor units: 6x4 or 8x4 Lowbed: * Lowbed with external beams, extendable in SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking * Supply lines are protected within the extendable beams and automatically adjust to the lowbed length * 7 pairs of lashing rings foldable outward (LC 10,000 daN) * 6 pairs of threaded blocks on the inner girder for mounting screw-on RUD rings Rear Undercarriage: * Rear chassis with closed outer frame and checker plate cover * Chassis with excavator trough, closed in the rear half to accommodate air tanks * 3 pairs of lashing rings foldable outward (LC 5,000 daN) * 1 pair of lashing rings foldable outward (LC 10,000 daN) * 1 pair of flat lashing rings, front and rear of the chassis (LC 10,000 daN) Axles: Kdsdpfsy Uwu Iox Akqjp * BPW axles and suspension, all axles hydromechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer of choice. Load index (146/146F) Brake System: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with 2 layers of 2K topcoat, single colour in RAL 3002 Carmine Red as per RAL system 841GL Including accessories: * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized connection bar at the front * Remote steering from front and rear via cable remote control with push buttons, including single-track axle control (without installation in the tractor unit) * Prepared for bolt-on container positioning for 1 x 20', 1 x 40', or 1 x 45' container on the outer beams. No container locks * Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings * Electro-hydraulic power unit * Spiral cable for supplying the electro-hydraulic power unit and/or electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between semi-trailer and tractor unit with plug connection (NATO-NATO) * Yellow reflective tape to EU regulations on sides, extension and rear of the trailer * At the gooseneck and rear, left and right, a bracket for warning signs including a socket * Manual and description on USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable guard around the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer beam for mounting screw-on RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above normal ride height, adjustable by hand control * On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (body length approx. 2,560 mm) * On the gooseneck, a separate air connection with air gun * 1 stainless steel toolbox, approx. 1,350 x 400 x 400 mm, mounted externally

Durum: ikinci el, azami yük ağırlığı: 36.100 kg, toplam ağırlık: 49.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 10/2026, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete inventory of vehicles, available immediately and at short notice, on our website. Partial list of features. Full equipment details upon request. Gooseneck: * Gooseneck in SNT design for optimized loading deck length, approx. 3,750 mm, hydraulically liftable/lowerable and detachable * Technical kingpin load: 25,000 kg * Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 Lowbed: * Lowbed designed as a telescopic vessel bridge in low-profile construction, extendable at the front with mechanical locking * Length x width approx. 6,850 mm x 2,540 mm * Supply lines run protected in the extendable beams and automatically adjust to the current lowbed length Axles and Suspension: * PENDLE-AXLE * All axles hydro-mechanically forced steered * Hose rupture valve on axle compensation * Cylinders with automatic RESET function * Hydraulic cylinders with shut-off valves and preload pins for securing in raised position * Technical axle load: 12,000 kg each * Hydraulic axle compensation * Tires: 245/70 R 17.5 * Rear chassis with closed external frame, checker plate cover, and continuous prism-shaped excavator recess approx. 1,250/700 x 505 mm, open at the rear Brake System: * Brake system: WABCO EBS-E in accordance with EU regulations, without connecting cables to the tractor unit Paintwork: * Trailer color: RAL 3002 Carmine Red Included Accessories: * Removable steel front wall, approx. 400 mm high * 3 kW electric-hydraulic power pack for hydraulic operations (except hydraulic winches), supply line installation on the tractor unit not included * Outer beams on the gooseneck with mounting holes for bolt-on lashing rings; first hole approx. 200 mm from the front, then every approx. 400 mm; 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear slope of the gooseneck (LC 6,000 daN) Kdedpfx Akox Uvlleqjp * 2" king pin * Locking point approx. every 500 mm on the extension * 1 pair of steel ramps with climbing slats and locking pins for bridging the lowbed receiving hooks * 1 lashing ring each left and right on the front crossmember (LC 10,000 daN) * Lashing rings with retaining spring every approx. 1,200 - 1,300 mm on the outside of the inner beams of the loading deck * Lashing rings with retaining spring every approx. 1,200 - 1,300 mm on the outside of the outer beams of the loading deck (LC 10,000 daN) on the top flange of the outer beams * Cutouts above the lashing rings * 1 hanging lashing ring each left and right outside on the rear crossmember (LC 10,000 daN) on the outer beams of the loading deck * Preparation for removable loading floor * Hanging bar at the front of the rear chassis for loose access ramps to the lowbed * Chassis with beveled rear corners * Hanging bar for loose aluminium ramps on the rear end traverse of the vehicle * Remote steering from front and rear via cable remote control with push-buttons, with axle tracking control, without installation in the tractor unit * Mechanical pin-latch coupling from lowbed to chassis for swapping loading platforms or installing extension beams, with electrical, pneumatic, and hydraulic couplings * Round NATO socket at the front connector bar (Maeler & Kaege VG 96 917) * 2 axle load gauges mounted on the left side Including special accessories: * 1 pair of removable aluminium side walls on the gooseneck, approx. 400 mm high, anodized finish * A

Durum: yeni, dingil konfigürasyonu: 3 aks, izin verilen dingil yükü (dingil 1): 12.000 kg, izin verilen dingil yükü (dingil 2): 12.000 kg, izin verilen aks yükü (aks 3): 12.000 kg, toplam uzunluk: 9.300 mm, toplam genişlik: 2.540 mm, süspansiyon: hava, lastik boyutu: 245/70 R17.5, dingil mesafesi: 1.360 mm, renk: mavi, Üretim yılı: 2023, Donanım: hidrolik arka platform, Farbe: Blau Nutzlast: 54.465 kg Hauptmerkmale: Hersteller: Faymonville Modell: MAX 110-Z-4AA-9.30-U Fahrgestellnummer: YAMT14XX4N0107629 Baujahr: Neu und unbenutzt Gewichte/Zuladung: Sattellast: 23.000 kg Achslast: 12.000 kg Gesamte Achslast: 48.000 kg Zulässiges Gesamtgewicht (zGG): 71.000 kg Leergewicht: 16.535 kg Nutzlast: 54.465 kg Achsen: Achsenfabrikat: BPW Hydraulische Lenkung Luftfederung mit Hub-/Senkventil WABCO-Bremssystem Bereifung: 245/70 R17.5 – Michelin (Tragfähigkeitsindex 146/146 F) 1. Liftachse Abmessungen: Ladeflächenlänge: 9.300 mm Verlängerungen: 6.500 + 6.800 mm Ladeflächenbreite: 2.540 mm Ladehöhe: 900 mm Weitere Ausstattung: Doppelt ausziehbarer Ladeboden Container-Verriegelungen Verbreiterungen in der Breite + Holzrungen für zusätzliche Breitenverbreiterung Zurringe Satz doppelt klappbare Auffahrrampen Zentralschmierung 1x Reserverad inkl. Halter JOST-Stützwinden Elektrisches System 24 Volt Sattelkupplung 2.0" 1 verzinktes Stahl-Frontgitter Elektrisch betriebene Hydraulikpumpe Manuelle Lenkung Twistlocks = Weitere Informationen = Allgemeine Informationen Baujahr: 2023 Achskonfiguration Bereifung: 245/70 R17.5 Federung: Luftfederung Achse 1: Doppelbereift; Liftachse; max. Achslast: 12.000 kg; gelenkt; Achsenfabrikat: BPW; Reifenprofil innen/außen links: 100%; Reifenprofil innen/außen rechts: 100% Achse 2: Doppelbereift; max. Achslast: 12.000 kg; gelenkt; Reifenprofil innen/außen links: 100%; Reifenprofil innen/außen rechts: 100% Achse 3: Doppelbereift; max. Achslast: 12.000 kg; gelenkt; Reifenprofil innen/außen links: 100%; Reifenprofil innen/außen rechts: 100% Achse 4: Doppelbereift; max. Achslast: 12.000 kg; gelenkt; Reifenprofil innen/außen links: 100%; Reifenprofil innen/außen rechts: 100% Gewichte Leergewicht: 16.535 kg Nutzlast: 54.465 kg zGG: 71.000 kg Funktionalität Ladehöhe: 900 mm Ausziehbarer Aufbau: Ja Zustand Allgemeiner Zustand: Sehr gut Technischer Zustand: Sehr gut Optischer Zustand: Sehr gut Finanzielle Informationen Preis: Auf Anfrage Kedpfxsuu Hcfs Akqodp

Durum: iyi (kullanılmış), makine/araç numarası: YAFTL6002R0035345, yükleme alanı uzunluğu: 14.800 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 9.000 mm, Üretim yılı: 2024, = Diğer seçenekler ve donanımlar = - Arka havalı süspansiyon - Ön havalı süspansiyon - Kampanalı fren sistemi = Diğer bilgiler = Yük kapasitesi: 81.100 kg Azami toplam ağırlık: 81.100 kg Teknik durumu: iyi Görsel durumu: iyi Ön lastik durumu: 60 Ön lastikler: 245/70 R17.5 Arka lastikler: 245/70 R17.5 Son muayene: 2025-12-28 Ksdpjx Rtiasfx Akqedp Daha fazla bilgi için Lastas Sales ile iletişime geçiniz.

Durum: yeni, azami yük ağırlığı: 38.953 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Gross vehicle weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading platform length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Steering angle radius (rear): 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck: Gooseneck with chamfered front corners at 45° and rear taper of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8°. 6 pairs of folding lashing rings facing outward (LC 5,000 daN). 2 pairs of folding lashing rings facing outward (LC 10,000 daN). 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN). Cut-outs in the outer frame of the loading platform for attaching tensioning straps. (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, above the axles fitted with chequer-plate covering. Ramps: Two-piece steel ramps: One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically foldable ramp sections, hydraulic lifting device and can be hydraulically adjusted laterally. Maximum load per pair: 40,000 kg Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R 17.5 tyres as per manufacturer's selection. Axles: SAF axles, air-suspended, with drum brakes, featuring lift/lower function. Last axle is force-steered with electro-magnetic reverse lock, activatable via reverse gear or manually. Axle tools. Brake System: Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit. Steel Construction: Steel construction made from high-strength fine-grained steel. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Ksdpfx Akog Sk Trsqsdp Painting: Premium and durable corrosion protection via sandblasted welded frame, primed with 2-component (2K) zinc dust primer. High-quality single-tone 2-component (2K) top coat in RAL colours of your choice. Rear metalized and painted in RAL 9010 (pure white). Metallic paint not possible. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets. ISO-compliant connections. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories Included 2" king pin One galvanized steel front bulkhead approx. 400 mm high. At the galvanized front connection strip yellow/red airline couplings. 4 wheel chocks with holder on the front bulkhead (± 5kg). Cable for supplying electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long, max. 250A) between semi-trailer and tractor unit, with plug connection (ANDERSON-ANDERSON). Galvanized folding supports under the rear slope of the loading platform. Bracket for a rotary beacon at the rear of the trailer. Control valves for the ramps installed on right-hand side of trailer (± 4kg). Yellow reflective tape according to EU regulations on the sides and rear of the trailer. Electro-hydraulic unit mounted at the rear under the loading

Durum: yeni, toplam ağırlık: 58.000 kg, Üretim yılı: 2026, Low-bed semi-trailer MAX100 4 A 8.60 U Technical Data Speed: 80 km/h Gross Vehicle Weight: 60,800 kg Fifth Wheel Load: 18,000 kg Axle Load: 42,800 kg Tare Weight: Payload: Gooseneck Length: 3,850 mm Loaded Fifth Wheel Height: 1,250 mm Loading Platform Length: 8,600 mm Extendable by: 5,400 mm Axle Spacing: 1,360 mm Steering Radius (rear): 2,300 mm Loading Height at Max. Load: 860 mm Overall Width: 2,540 mm Suspension Stroke: -55/+145 mm Technical Description Gooseneck With 45° chamfered front corners and rear chamfer approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) 30 mm thick hardwood floor Extendable loading platform With rear bevel approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings (LC 5,000 daN) 3 pairs of outward-folding lashing rings (LC 10,000 daN) 1 pair of flush-mounted lashing rings at the front of the loading platform (LC 10,000) Approx. 48 mm thick hardwood flooring, chequer plate above the axles Ramps Two-part steel ramps One pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 mm x 800 mm with approx. 48 mm hardwood flooring Ramp sections hydraulically lifted and folded in, hydraulic lift and hydraulically adjustable position Max. load per pair: 40,000 kg Tyres 235/75 R 17.5 Brake System compliant with EU regulations, with EBS-E (4S3M) Without connection lines to the tractor unit Paintwork First-class, long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by 2-component zinc dust primer High-quality 2-component (2K) top coat, single colour, in RAL shades of choice Rear section metallized and painted in RAL 9010 (Pure White) Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24t Lifting capacity (50t test load) Steel construction made from high-strength fine-grained steels. Steel Qualities: Steel construction made from high-strength fine-grained steel S355J2+N/S355MC (Yield Strength 355MPa) S690QL/S700MC (Yield Strength 690MPa) Electrical System according to EU regulations, lighting: LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets Connection as per ISO. 24N IS0-1185 Kedpsg Sk T Dofx Akqodp 24S IS0-3731 15-pin IS0-12098 Accessories included: One galvanized steel headboard approx. 400 mm high 2" king pin 4 wheel chocks with holders on the headboard One holder for revolving beacon at rear of trailer SAF axles, two rigid axles, one self-steering axle, air suspension, with drum brakes, with raise/lower function The self-steering axle with electromagnetic reverse lock, can be activated by reverse gear or manually Axle tools included Support for ALU approach ramps at the rear of the gooseneck Galvanized folding supports under the loading platform chamfer Mechanical safety lock for the loading platform extension One spare wheel with holder in front of the headboard Yellow reflective tape as per EU regulations on sides, extension, and rear of trailer At the front galvanized connector strip, yellow-red air couplings On gooseneck and rear apron left and right, mounts for warning plates, including sockets A mudflap at the rear of the trailer Manual and description On the gooseneck: Plug-in aluminium sideboards and rear wall, approx. 2,440 x 400 mm (LxH) Rear galvanized stanchions are removable Body length approx. 2,560 mm, +/- 46 kg 3 pairs of WADER container locks in the loading platform for a 20', 30', or 40' container (±30 kg) 6 pairs of pockets for plug-in stanchions

Durum: yeni, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Gross weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Loaded saddle height: 1,200 mm Rear steering radius: 2,300 mm Loading platform length: 6,850 mm Extendable by: 5,500 mm Loading height at maximum load: 350 mm Chassis length: 2,600 mm Rear chassis loading height at max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Overall width: 2,540 mm Gross weight depends on fifth wheel load. Lowbed: Lowbed with external beams, extendable version "SUPER LOW" design, length approx. 6,850 mm. Lowbed with fixed hardwood floor approximately 40 mm thick and mechanical locking device. Supply lines are protected inside the extendable beams and automatically adjust to the respective lowbed length. 5 pairs of lashing rings, foldable outward (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear chassis: Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at rear. 2 pairs of lashing rings, foldable outward (LC 10,000 daN). 1 pair of lashing rings, flat in the trough (LC 8,000 daN + 5,300 daN). 2 pairs of pocket sockets for stanchions 100 x 50 mm in the external frame. Gooseneck: Gooseneck in SNT design to optimize usable platform length, length approx. 3,785 mm. Gooseneck hydraulically lift/lowerable and detachable. Technical fifth wheel load: 23,000 kg For tractor units: 4x2, 6x2, and 6x4 Kdjdpfxeizu Nwe Akqjp PENDLE-AXLE: “PENDLE-AXLE”, all axles hydro-mechanically forced steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and plug pins for securing in raised position. Axles finished with two coats of 2-component paint, single color "FAY-Grey-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tools. Brake system: Brake system in accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit. Electrical system: Electrical system according to EU regulations, 24V lighting ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection strip with 24N, 24S, and 15-pin sockets. Connection according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel construction: Steel construction made of high tensile fine-grained steels. Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Painting: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer. Premium two-component (2K) topcoat in one RAL color of your choice. Rear section metallized and painted in RAL 9010 (Pure White). No metallic paint possible. Tyres: Tyres 245/70 R 17.5 3PMSF Manufacturer’s choice. Load index (146/146F). Prepared for fitting of bolt-on container positions for 1x 20' or 1x 40' container on the external beams. Without container locks. • 2” king pin • Galvanized steel front wall approx. 400 mm high • 1 spare wheel with holder in front of the front wall • 2 wheel chocks with holder on the front wall • Yellow-red air couplings on the galvanized connection strip at the front. Remote steering from front and rear via cable remote control with pushbuttons, with single-track axle monitoring (without installation in the tractor unit). Hydraulic connections from the gooseneck to the lowbed

Durum: yeni, azami yük ağırlığı: 36.461 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.480 mm, toplam yükseklik: 860 mm, Üretim yılı: 2026, Technical Description Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Area: Hydraulically liftable and lowerable platform after the gooseneck, approx. 2,800 mm in length, with rear taper approx. 1,000 mm x 8°. 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN). 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN). 1 pair of foldable lashing rings to the inside on the front central beam (LC 10,000 daN). Grating floor covering C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles tread plate covering. Two-Piece Steel Ramps: One pair of galvanized two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating covering C40/5 (point load 8 t on an area of 20 x 20 cm). Ramps with hydraulically folding ramp sections and hydraulic lifting mechanism. Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not included in the overall vehicle length of 16,500 mm. Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R17.5 3PMSF tyres at the manufacturer’s discretion. TPMS: TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface according to ISO 11992. For proper display, the towing vehicle must be capable of transmitting and displaying this data. Axles: BPW axles and suspension, 2 rigid axles, 1 trailing steering axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated by reverse gear and manually. Air suspension with lift and lower valve. Axle tools. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit. Electrical System: Electrical system complying with EU regulations, 24-volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicators. ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Manufactured from high-strength fine-grained steels. Steel grades: – S355J2+N / S355MC (yield strength 355 MPa) – S690QL / S700MC (yield strength 690 MPa) Curtain Body: Kodew Dl Hwepfx Akqodp Curtain body ??? 3,960 mm ??? – Galvanized front wall with tensioning system for sliding curtains. – "EDSCHA" brand roof, forward-sliding on ALU roof bow profiles (bolted to front and rear wall). – 3 pairs of sliding stakes in the loading area. – Rear of the body hydraulically extendable to left and right by approx. 750 mm. – Sliding roof with upwards foldable portal beam. – Sliding curtain with 700 mm length reserve, lashing straps approx. every 600 mm. – Height to upper edge of body approx. 3,960 mm (loaded). – Driving with open sliding roof is prohibited and will damage the curtain. Paintwork: Entire steel structure is automatically blast-cleaned with a wheel blasting machine after welding. Second blast treatment with corundum for optimal coating adhesion. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection. Final painting with 2 coats of 2K topcoat, single colour, shade of choice according to RAL system 841GL. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint.

Durum: yeni, azami yük ağırlığı: 36.156 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Gross vehicle weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Tare weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Platform length: 13,600 mm Loaded fifth wheel height: 950–1,050 mm Swing clearance at rear: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360 / 1,405 mm Overall width: 2,540 mm Technical Description Load platform: Load platform in extendable design with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of fold-out lashing rings (LC 5,000 daN). 2 pairs of fold-out lashing rings (LC 10,000 daN). Cut-outs in the outer frame of the platform for attaching tension straps (LC 2,000 daN). Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). Trailing steering axles with electro-magnetic reversing lock, activated via reverse gear or manually. Axle tools (± 80 kg). Brake system: Brake system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Kdodpfx Akjg Sk Tvsqjp Paintwork: Premium, long-lasting corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc-rich primer. High-quality two-component (2K) topcoat, single-colour, in RAL tones of your choice. Rear section metallised and painted in RAL 9010 (pure white). Metallic paint not available. Electrical system: Electrical system according to EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connector panel with sockets 24N, 24S & 15-pin. Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Standard accessories included: Yellow-red air couplings on the galvanised front connector panel. 2 wheel chocks with holders. 2" kingpin. Galvanised steel front wall, approx. 2,200 mm high (± 105 kg), EN12642-XL compliant. Yellow reflector tape according to EU regulations; fitted along the sides, on the extension, and the rear of the trailer. European reflective warning plates (red-yellow) at the rear of the trailer. Platform with approx. 38 mm hardwood floor (± 320 kg). 10 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the platform (± 30 kg). 1 spare wheel holder under the platform, right-hand side in direction of travel. Tyres 435/50 R 19.5, manufacturer’s choice. One mud flap at the rear of the trailer. Manual and documentation on USB stick. Bracket for rotating beacon at the rear of the trailer. At the gooseneck and rear panel, left and right, brackets for warning signs, incl. socket. One transverse INOX toolbox under the platform (1,000 x 400 x 250 mm) (± 135 kg). 6 pairs of WADER container locks in the platform for 1 x 20’ container, 2 x 20’ containers or 1 x 40’ container; an additional locking position provided in the extension for a 45’ container (± 90 kg). 4 pairs of WADER container locks (± 60 kg). 10 pairs of galvanised plug-in stakes approx. 100 x 50 mm, 1,000 mm high (± 220 kg). 3 pairs of crosswise stake pocket bars mounted in the platform for plug-in stakes 100 x 50 mm (± 95 kg). Storage for 1,000 mm plug-in stakes (± 45 kg). 1 spare wh

Durum: yeni, azami yük ağırlığı: 44.000 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, Further information here: Ksdpfx Akov D Abtjqodp

Durum: yeni, azami yük ağırlığı: 40.017 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Kedow Dl Hqopfx Akqodp Loading Area: 5 pairs of fold-out lashing rings (LC 5,000 daN). 3 pairs of fold-out lashing rings (LC 10,000 daN). 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN). Hardwood flooring approx. 48 mm thick, tread-plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 205/65 R17.5, manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface as per ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles: two fixed axles, two self-steering axles, air suspension, drum brakes, lifting/lowering function. The self-steering axles have electro-magnetic reverse lock, activated via reverse gear or manually. Axle tool included. Brake System: WABCO brake system compliant with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit. Electrical System: Electrical system as per EU regulations, 24 Volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights synchronise with the indicator. ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets. Connections in accordance with ISOs: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: Entire steel structure automatically shot blasted after welding using a shot blasting system. Second blasting treatment with corundum for optimum adhesion of the coating system. HRM metallisation of the complete chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection. Final painting: two coats of 2-pack topcoat, single-colour in a shade of choice according to the RAL 841GL system. Rear section metallised and painted in RAL 9010 (pure white). Metallic finishes not available. Paint specification tested according to salt spray test ISO 9227-NSS. Cavity sealing with special wax. Options Included: 2'' kingpin One galvanised steel front wall. Yellow-red air couplings fitted to the galvanised front connection rail. 2 wheel chocks with holders on the front wall. Mountings at the rear of the gooseneck for ALU ramps. Further options available.

Durum: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, 3-axle MULTIMAX PLUS low-loader semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross weight: 49,500 kg or 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Coupling height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: (value not specified) Loading area width approx.: 2,540 mm Loading height at max load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific legal limits are exceeded. Technical Description Gooseneck: SNT design gooseneck to optimize loading platform length, approx. 3,900 mm length, with rear chamfer approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading area: Loading platform approx. 9,600 mm length with rear chamfer approx. 900 mm x 6°. Section after the gooseneck is hydraulically raisable/lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS Pair of two-section AXS steel ramps, approx. 4,920 mm long and 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Each ramp hydraulically shiftable approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle as per technical datasheet: C470319. Maximum gradient at lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg. Air suspension with lift/lower valve. Axle tools included. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion. Load index 143/141J (144/144F). Braking system: WABCO EBS-E braking system per EU regulations. No cables to the tractor unit. Lighting system: 24V "ASPÖCK-NORDIK full LED" lighting per EU regulations (ASS 3). Metallisation: Complete HRM (High Resistance Metallisation). Full steel structure shot-blasted, then hot-coated with ZINACOR 850 (85% zinc / 15% aluminium). Painting – 6-stage finish: - Complete steel structure shot-blasted after welding - 1 coat zinc-based primer, 1 coat adhesion primer - Top coat with 2 coats 2K acrylic paint, single colour in RAL shade of choice - Cavity sealing with special wax - Rims in silver - Multicolour & special paint available at extra cost Steel structure: High-tensile fine-grain steels Types: S355J2+N/S355MC (yield stress 355 MPa), S690QL/S700MC (yield stress 690 MPa) Welders certified to DIN-EN 287-1, MAG welding per EN ISO 4063, M21 shielding gas as per EN ISO 14175. Front wall: Removable steel front wall, approx. 400 mm high. Supply connection strip for connections to tractor unit, fitted at outer frame profile height. ASPÖCK-UNIBOX at the front supply strip with 24N, 24S & 15-pin sockets. - 24N connection per ISO-1185 - 24S connection per ISO-3731 - 15-pin connection per ISO-12098 Kdjdpfxsizu Ntj Akqep If your pin assignment deviates from the ISO standard, please inform us. "Anderson" socket on front supply strip: Rema 78051-00 & Amp. 150 V. Cable for the supply of the electro-hydraulic power pack and/or electric winch (35 mm²,

Durum: yeni, azami yük ağırlığı: 34.104 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2026, Further information here: Ksdsv D Abgepfx Akqjdp

Durum: ikinci el, boş ağırlık: 15.550 kg, azami yük ağırlığı: 47.450 kg, toplam ağırlık: 63.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 11/2024, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, Üretim yılı: 2024, Donanım: ABS, For every used semitrailer, you will receive a current and comprehensive inspection and functional report. Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,700 mm long - Gooseneck rear with chamfer, approx. 1,000 mm x 10° Loading area: - Extendable loading platform, approx. 8,800 mm long, with rear chamfer approx. 500 mm x 10° - A recess in the loading platform, including into the chamfer, for accommodating the excavator bucket arm - Pneumatic locking system with conical locking pins and reinforced locking positions - Hardwood flooring on the loading platform chamfer Ramps: - 1 pair of two-part steel ramps, approx. 4,350 mm long and approx. 900 mm wide - Ramps laminated with hardwood - Hydraulically foldable ramp tips - Ramps can be hydraulically moved individually approx. 235 mm outward and approx. 215 mm inward - Square serrated crossbars 20 x 30 mm, every approx. 200 mm on the outer frame of the ramp Axles and suspension: - BPW axles and suspension, first axle self-steering, all other axles hydromechanically forced steering - Technical axle load: 12,000 kg - Air suspension - Tyres 235/75 R 17.5 - TPMS tyre monitoring system - TPMS tyre sensors Accessories included: - Removable front wall, steel, approx. 400 mm high - 3kW electro-hydraulic power unit for hydraulic operations - 1 spare wheel - External beams of the gooseneck with mounting holes for bolt-on lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear of the gooseneck - On the gooseneck: 1 pair of plug-in ALU sidewalls, approx. 400 mm high, anodized - On the gooseneck: 1 plug-in ALU rear wall, approx. 400 mm high, anodized - 2" king pin - Round NATO socket at the front connection bar - 4 wheel chocks - Mechanical landing legs with 2-speed gearbox and crank - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross member - 8 pairs of recessed, foldable lashing rings in the outer frame of the loading area - Expandable (galvanized) extensions up to approx. 230 mm per side - Wheel recesses with square serrated strips, 15 x 15 mm, continuously open ahead of the axles up to the gooseneck cross member, approx. 700 x 410 mm - ALU covers for wheel recesses - ALU elements lockable on the extension tubes of the width extensions - Expandable U-profiles for ALU covers - Wheel recesses with square serrated strips, 15 x 15 mm between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU elements lockable on the extension tubes of the width extensions - 1 pair of mechanical rear supports - Rear steering operable from front and rear via cable remote control, with axle tracking control - 1st axle with automatic lift axle function and starting aid in accordance with EU Directive 2021/535 - Under the gooseneck and at the rear crossbar left and right, each with a 7-pin socket with holder for warning boards - Square serrated strips 20 x 30 mm, every approx. 200 mm on the outer frame of the loading platform chamfer - Central lubrication system with 1 pump, brand BEKAMAX Kjdpfxeypb Aks Akqsdp - Radio remote control for rear steering, in addition to cable remote - Wabco Smart Board system - 4 extendable warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm

Durum: yeni, boş ağırlık: 15.550 kg, azami yük ağırlığı: 47.450 kg, toplam ağırlık: 63.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long - Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator bucket arm - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood flooring on the bevel of the loading platform Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide - Ramps with hardwood covering - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - Square climbing strips 20 x 30 mm, at approx. 200 mm intervals on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, first axle steerable, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated automatically in reverse gear and manually - Air suspension with lift and lower valve - Tires: 235/75 R 17.5 twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS tire sensors installed in all wheels, including spare wheels Accessories included: - Detachable front wall, steel, approx. 400 mm high - 3kW electro-hydraulic power unit for operating hydraulic functions, except hydraulic cable winch - Parking bracket for warning signs on gooseneck when not in use - 1 spare wheel - On the gooseneck: 1 pair of detachable ALU side boards, approx. 400 mm high, anodized - On the gooseneck: one detachable ALU rear board, approx. 400 mm high, anodized - Over the gooseneck: approx. 40 mm thick hardwood covering, checker plate covering above king pin - 2'' king pin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with two-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide - Telescopic width extensions (galvanized) approx. 230 mm per side Kedpfx Ask Aht Uokqsdp - Wheel recesses with square climbing strips - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering from front and rear via cable remote control, with single track axle monitoring - 1st axle with automatic lifting axle function - Central lubrication system with 1 pump, BEKAMAX brand - Wireless remote control for remote steering, in addition to cable remote, with 2 indicator lights on receiver for single track monitoring - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for beacon

Durum: yeni, boş ağırlık: 15.420 kg, azami yük ağırlığı: 61.080 kg, toplam ağırlık: 76.500 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 900 mm, lastik boyutu: 235/75/r17,5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck with rear bevel approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Load area: Extendable load area with rear bevel approx. 500 mm x 8° 8 pairs of outward folding lashing rings 1 pair of flat-fitted lashing rings at the front of the load area Recesses in the outer frame of the loading area for attaching tie-down straps Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Two-piece steel ramps: One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramp sections hydraulically lift and fold, hydraulically height-adjustable, and hydraulically shiftable. Maximum load per pair: 50,000 kg. Landing legs: • JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tires: BPW axles and suspension, 4th and 5th axles steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lockout, activated via reverse gear and manually Tires 235/75 R 17.5 3PMSF Braking system: Braking system according to EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector rail with sockets 24N, 24S & 15 pin Connection compliant with ISO: 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer High-quality 2-component (2K) topcoat, single color MB 7350 Novagrau Rear part metalized and painted in RAL 9010 (pure white) No metallic paint possible Steel construction: Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Accessories: One spare wheel with holder in front of bulkhead 2" kingpin One galvanized steel front wall, approx. 400 mm high Yellow-red air couplings mounted on the galvanized connector rail at the front 2 wheel chocks with holder on the front wall Bracket at rear of gooseneck for ALU drive-on ramps One holder for a rotating beacon at the rear of the trailer Galvanized supports beneath the rear bevel of the loading area White reflector tape according to EU regulations on the sides, extension, and rear in red Electro-hydraulic unit at rear under the loading area Mounts for warning signs with socket at the gooseneck and rear plate left and right Kedel Sl Izspfx Akqedp Ramp control valves fitted to right-hand side of the trailer One mud flap at the rear of the trailer Manual and documentation on USB stick 3.5" kingpin supplied loose Plug-in ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm (LxH) Rear galvanized drop-in stakes are removable (structure length approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or 40' container 6 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area Galvanized extensions, extendable by approx. 230 mm per side Lifting axle on the front axle with control via TEBS E, depending on the current axle load and current loading condition Square cleats 20 x 20 mm every 200 mm on the outer frame of the loading area's bevel On the checker plates, above the kingpin and the loa...

Durum: yeni, boş ağırlık: 12.300 kg, azami yük ağırlığı: 37.200 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 30 mm thick hardwood flooring - 3 pairs of lashing rings Two-part steel ramps: - One pair of galvanized two-part steel ramps approx. 3,185 x 1,420 x 1,250 mm with grating surface - Ramps with hydraulically foldable ramp sections and hydraulic lifting system - Maximum load per pair: 30,000 kg Kdsdpfxotvfkfs Akqop Loading platform: - Loading platform with rear chamfer approx. 1,000 mm x 8° - Approx. 48 mm hardwood flooring, over the axles with checker plate surface Axles and tires: - BPW axles and suspension, two rigid axles, one self-steering axle - Air suspension with lift and lower valve - Self-steering axle with electro-magnetic reverse lockout, activated via reverse gear or manually - Tires 235/75 R17.5 3PMSF Accessories included: - 1 spare wheel with holder - TPMS tire pressure monitoring system according to ECE R 141 - 2" king pin - One galvanized steel headboard - Yellow-red air couplings on the galvanized connection rail at the front - 4 chocks with holders on the headboard - Mounting at the rear of the gooseneck for ALU drive-on ramps - 3 height levels of aluminum planks - Galvanized folding supports under the chamfer of the loading platform - Height-adjustable tarpaulin frame (3,960 mm) - Galvanized headboard with tensioning mechanism for sliding curtain - Height adjustable by approx. 400 mm - Roof brand "EDSCHA" sliding forward on ALU roof rail profiles, bolted to front and rear wall - 3 pairs of sliding stakes in the loading platform - Body rear left and right hydraulically extendable by approx. 750 mm - Sliding roof with pivotable portal beam - Sliding curtain with 700 mm reserve length, with tension belts at spacing approx. 600 mm - Upper edge of structure approx. 3,960 mm high - Driving with open sliding roof is not permitted and will cause damage to the curtain - Cover plates for bridging the gap between ramps and loading platform - Electro-hydraulic unit at the rear, beneath the loading platform - At the gooseneck and at the ramps left and right each a bracket for warning panels incl. socket - Control valves for the ramps positioned on the right trailer side - 6 pairs of stake pockets for insertable stakes 100 x 50 mm in the outer frame of the loading platform - Lift axle at the front axle - Grating surface in the chamfer of the loading platform C40/4 (point load 3.4 t on an area of 20 x 20 cm) - One INOX toolbox 565 x 290 x 810 mm on the right in driving direction between the axles - On the checker plate on the gooseneck and loading platform, a painted sand layer for slip resistance - Central lubrication system BEKAMAX (Pico) with standard lubricant NLGI-2 and removable guard around the pump - Four warning panels extendable by approx. 400 mm, each approx. 423 x 423 mm, with position light - Load pressure gauge for determining axle loads including load chart - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure shot-blasted, then visible defined surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - alu 15%)

Durum: yeni, boş ağırlık: 13.500 kg, azami yük ağırlığı: 51.500 kg, toplam ağırlık: 69.500 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 r17.5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck in SNT design for optimization of loading area length, length approx. 3,700 mm Gooseneck rear with bevel approx. 1,000 mm x 10° Loading Area: Telescopic loading area, length approx. 8,800 mm, with rear incline approx. 500 mm x 10° Recess in the incline and extending into the loading area for accommodating the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected within the extendable beam and adjust to the respective loading area length Ramps: 1 pair of two-piece steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically adjusted individually approx. 235 mm outwards and 215 mm inwards Axles and Suspension: BPW axles and suspension, two fixed axles, two steering trailing axles Electromagnetic reverse lock activated via reverse gear and manually Air suspension with lifting and lowering valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO brake system, EBS-E according to EU regulations Lighting System: 24-volt lighting system, “ASPÖCK-NORDIK full LED” Metallization: Standard HRM metallization of the external frame Complete steel structure shot blasted, subsequently visible defined surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished Steel Structure: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified according to DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included accessories: Removable steel front wall, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 Round NATO socket on the front connection strip Cable for supplying the electro-hydraulic pump and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations (except for hydraulic winches) 1 spare wheel with mounting adapter External beams on the gooseneck with mounting holes for bolt-on lashing rings, first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included Mounting hole on the upper rear of the gooseneck external beam for a screw-on lashing ring 1 pair screw-in lashing rings Approx. 40 mm thick hardwood floor above gooseneck On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized On the gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodized 2" king pin Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 4 wheel chocks with holders Provision for aluminium approach ramps Kdjdpfxjk Ahugj Akqep Mechanical landing gears with 2-speed gearbox and crank On the loading area, continuous hardwood floor approx. 50 mm thick, interrupted only between the axles Load area locking with conically welded positioning profiles every 250 mm including pre-tension plate Slotted holes at the front of the loading area for attachable and repositionable bridging plates 1 intermediate table with recessed loading area, approx. 300 mm wide, for the large cross-section sliding tube with sheet metal covering Front and rear with longe...

Durum: yeni, boş ağırlık: 13.250 kg, azami yük ağırlığı: 47.550 kg, toplam ağırlık: 60.800 kg, dingil konfigürasyonu: 3 aks, süspansiyon: hava, lastik boyutu: 245/70 r17.5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings 30 mm thick hardwood flooring Extendable loading platform: Extendable loading platform with rear taper approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings 3 pairs of outward-folding lashing rings 1 pair of horizontal lashing rings at the front of the loading platform Kdedpol Uxdkefx Akqep Cutouts in the outer frame of the platform for attaching tension straps Approx. 48 mm thick hardwood flooring, checker plate over the axles Two-piece steel ramps: One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding ramp sections, hydraulic lift mechanism, and hydraulically adjustable. Maximum load per pair: 40,000 kg Landing legs: JOST landing legs (mechanical) with two-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tires: BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced-steered Technical axle load: 12,000 kg Air suspension with lift and lower valve Axle tool Tires 245/70 R 17.5 Brake system: Braking system according to EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Steel structure: Steel structure made of high-strength fine-grain steels Steel qualities: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer High-quality two-component (2K) topcoat in single-tone Nova Grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint possible Electrical system: Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" king pin Galvanized steel front wall approx. 400 mm high Yellow-red air couplings at the galvanized front connection bar 4 wheel chocks with holder at the front wall One spare wheel with holder in front of the front wall Electro-hydraulic unit Remote steering front and rear via cable remote control with push buttons and single-track axle alignment control Mount for ALU loading ramps at rear section of the gooseneck European reflector boards (red-yellow) at the rear of the trailer White reflector tape as per EU regulations on the side, extension and rear Red at the rear At the gooseneck and ramps, one holder left and right for warning signs including socket Beacon holder at the rear of the trailer Galvanized folding support legs under the rear ramp of the loading area Control valves for ramps located on the right side of the trailer Cover plates to bridge the gap between ramp and loading platform One mud flap at the rear of the trailer Manual and description on USB stick BEKAMAX (Pico) central lubrication system with standard NLGI-2 grease and removable protection for the pump Plug-in ALU side and rear walls on the gooseneck approx. 2,440 x 400 mm Rear galvanized plug-in posts are removable, superstructure length approx. 2,560 mm One INOX toolbox 1,350x400x400 on the gooseneck, box covers oil fill plug 4 pairs of WADER container locks in the loading area for a

Durum: yeni, boş ağırlık: 17.250 kg, azami yük ağırlığı: 48.700 kg, toplam ağırlık: 66.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 375 mm, lastik boyutu: 245/70 R 17.5, renk: gri, işletme ağırlığı: 17.250 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized load platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Suitable for tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: - Low bed with external beams, configured as a telescopic vessel bridge in low construction with extension at the front - Length x width approx. 7,550 mm x 2,740 mm Kdsdpfx Aeh Hm Tzskqep - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Tread plate covering and continuous prismatic excavator recess approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Final coating of axles with 2 layers of single-colour 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps with climbing strips and fixing bolts for bridging the low bed uptake hooks - Ramps can be placed over or between the hooks - Mounting points for steel loading ramps at the rear between the external beams of the gooseneck - One locking position approximately every 1,000 mm on the extension - 1 lashing ring each left and right on the front cross member - Supply line connection strip to the tractor unit, fitted at the height of the outer frame profile - 6 pairs of threaded blocks on the outside of the inner beams of the load platform for mounting screw-on M24 rings - 6 pairs of recessed lashing rings on the outside of the outer beams of the load platform, foldable inwards and outwards - 1 pair of threaded blocks at the front and rear of the outer beams of the load platform for mounting screw-on M24 rings - Insertion strip for loose ALU approach ramps on the rear cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering from front and rear, operable via cable remote control, with single-track control of axles - 3 kW electro-hydraulic power pack for operating hydraulic functions, except hydraulic winches - Removable load floor (galvanised), can be inserted in 3 elements between the outer beams, with hardwood covering - Folding extensions, approx. 230 mm per side - Loose widening boards, framed in steel - 4 warning panels approx. 423 x 423 mm - Radio remote control for remote steering operation - 3.5" kingpin - Anti-slip stickers on the left bevel of the gooseneck - Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings - Guiding plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning panels when not in use - 2 pairs of stanchion pockets recessed in the outer frame of the chassis for insertable stanchions approx. 100 x 50 mm - Rear section of the chassis with a detachable plate closing the bucket arm recess at the rear - Trailer colour MB 7350 Novagrau

Durum: yeni, azami yük ağırlığı: 49.000 kg, toplam ağırlık: 60.800 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 r 17.5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with front corners beveled at 45° and rear taper approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable Loading Platform: - Loading platform in extendable design with rear taper approx. 1,000 mm x 8° - 5 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - c. 48 mm thick hardwood flooring, over the axles with checker plate covering Detachable Two-Part Ramps: - One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting unit and hydraulically adjustable - Maximum load per pair: 40,000 kg Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and Tyres: - BPW axles, two rigid axles, two steering trailing axles, air suspension, with drum brakes, with raise/lower function - The trailing steering axles can be locked electromagnetically via reverse gear or manually - Axle tools - Tyres: 235/75 R 17.5 Brake System: - Brake system according to EU regulations with EBS-E (4S3M) Steel Construction: - Steel construction made of high-tensile fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer Kodpfxjh Etf Re Akqedp - High-quality 2-component (2K) top coat finish in single-colour Novagrau Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front terminal strip with 24N, 24S & 15-pin sockets Accessories Included: - 2" king pin - One galvanized steel front wall approx. 400 mm high - One spare wheel with holder in front of the headboard - Yellow-red air couplings at the galvanized front terminal strip - 4 chocks with holder at the front wall - Mounting at the rear area of the gooseneck for ALU drive-on ramps - Galvanized folding supports under the taper of the loading platform - Bracket for a rotating beacon - Cover plates to bridge the gap between ramps and loading platform - White reflector tape to EU specification on the sides, red at rear and on extension - Electro-hydraulic power pack - On both sides of the gooseneck and ramps, mounting brackets for warning signs incl. socket outlet - Ramp control valves installed on the right trailer side - One mudguard at the rear of the trailer - Instruction manual and description on USB stick - ALU side walls and end wall, plug-in, on gooseneck approx. 2,440 x 400 mm - The rear galvanized plug-in posts are removable (length of structure approx. 2,560 mm) - 4 pairs of WADER container pockets in the loading platform for one 20ft, 2x 20ft or one 40ft container - 7 pairs of stake pockets for 100 x 50 mm plug-in posts in the outer frame of the loading platform - Extensions, galvanized, extendable by approx. 230 mm per side - Lift axle on the front axle with control - Square climbing rails 20 x 20 mm - Central lubrication system BEKAMAX - F

Durum: yeni, boş ağırlık: 12.900 kg, azami yük ağırlığı: 34.100 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, yükleme alanı uzunluğu: 6.850 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 350 mm, süspansiyon: diğer, lastik boyutu: 245/70 R 17,5, renk: gri, işletme ağırlığı: 12.900 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,750 mm long - Gooseneck hydraulically height-adjustable and detachable - Technical fifth wheel load: 23,000 kg - Suitable for tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading Platform: - Low bed with external beams in extendable "SUPER LOW" design, length approx. 6,850 mm - Low bed with fixed hardwood floor approx. 40 mm thick and mechanical locking Rear Chassis: - Rear chassis with closed outer frame, checker plate covering and continuous prismatic excavator trough approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of lashing rings foldable outward - 1 pair of lashing rings lying in the trough - 2 pairs of stake pockets for plug-in stakes (100 x 50 mm) in the outer frame Pendulum Axle and Tires: - "PENDULUM AXLE", all axles hydromechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pre-insert to secure in lifted position - Final coating of axles with 2 layers of single-color 2K paint, painted in "FAY-Grey-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 245/70 R17.5 Kdjdpfjhlz R Sex Akqep - TPMS (Tire Pressure Monitoring System) compliant with ECE R 141 Accessories: - Prepared for fitting of bolted container locking positions for 1x 20ft or 1x 40ft container on the external beams - 2" kingpin - Galvanized steel front wall approx. 400 mm high - One spare wheel - On the galvanized connection strip at the front: yellow-red air couplings - 4 wheel chocks - Remote steering front and rear operable via cable remote control with push buttons, including single-track monitoring of the axles - Hydraulic connections from gooseneck to low bed with multi-coupling instead of threaded couplings - Electro-hydraulic unit - White reflector tape on sides, extension and rear, according to EU regulations - European reflector panels (red-yellow) at the rear of the trailer - At the gooseneck and rear panel, left and right, each with a bracket for warning signs including socket - 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting of bolt-on RUD rings VLBG-4 - Removable ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized plug-in posts are removable (body length approx. 2,560 mm) - Gooseneck at the upper rear area closed with a removable cover - 5 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading platform - Fold-out extensions, approx. 230 mm per side - 2 pairs of bolt-on RUD rings VLBG-4 M24 (LC 8,000 daN) - 1 pair of steel ramps for bridging the low bed’s mounting hooks - Sanded layer painted on the loading platform as an anti-slip coating - Speed stickers 80 km/h on rear and both sides - Rear chassis’ bucket recess at the rear closed with a plug-in plate - Four warning panels extendable by approx. 400 mm, size approx. 423 x 423 mm - Radio remote control for the rear steering, in addition to the cable remote control, with indicator lights on the receiver as single-track monitoring - Central lubrication system with 2 BEKAMAX (Pico) pumps using standard grease NLGI-2 - Load gauge for determining axle loads - HRM (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces hot-finished in metallization with ZINACOR 850 (Zinc 85% - Alu 15%)

Durum: yeni, boş ağırlık: 14.350 kg, azami yük ağırlığı: 53.450 kg, toplam ağırlık: 67.800 kg, dingil konfigürasyonu: 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, hidrolik arka platform, Gooseneck: - Gooseneck in SNT design to optimize the loading deck length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - Suitable for tractor units: 6x2, 6x4, 8x4 short Loading Platform: - Loading platform with extendable design, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° - Recess in the loading platform as well as extending into the chamfer for accommodating the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-Part Steel Ramps: - One pair of two-part steel ramps, each approx. 4,350 mm long and approx. 900 mm wide - Ramps with rubber covering - Ramps can be hydraulically adjusted individually approx. 235 mm outward and approx. 215 mm inward - "Super Grip" rubber flooring 25 mm and steel plate flooring approx. 5 mm as additional reinforcement on the chamfer of the platform - Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles, suspension, and tires: - BPW axles and suspension, 1st axle steered, all other axles forced steered hydromechanically - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, can be activated via reverse gear and manually - Air suspension with lifting and lowering valve - Tires 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R141 - TPMS tire pressure sensors fitted on all wheels including spare wheels Surface Treatment: - Complete steel construction automatically shot-blasted with blasting machine after welding - Second blasting process with corundum for optimal adhesion of the coating system - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure best possible corrosion protection - Final coating with 2 layers of single-color 2-component topcoat in MB 7350 Novagrau Included Accessories: - Steel front wall, plug-in, approx. 400 mm high - 3kW electric-hydraulic power unit for hydraulic controls, except for hydraulic winches - 1 spare wheel - External beam on gooseneck with mounting holes for screwable lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - Approx. 40 mm thick hardwood floor on the gooseneck, checker plate at the king pin area - 2" king pin - Round NATO socket at the front connector strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross beam - 8 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outward Kedpfx Aeya E A Nokqedp - Extensions (galvanized) extendable by approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm, continuously open in front of the axles up to the cross beam of the gooseneck, approx. 700 x 410 mm - Wheel recesses with square climbing strips, 15 x 15 mm, between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for the wheel recesses, also usable as bridging elements for the extension or as extension beams - 1 pair of mechanical rear supports - Remote control (radio and cable) - Lifting axle at the front axle - Square climbing strips 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning boards, approx. 423 x 423 mm