Kullanılmış Faymonville Yarı Römorklar satın al (185)

Durum: yeni, azami yük ağırlığı: 46.800 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: > 3 aks, Donanım: ABS, Web sitemizde hemen ve kısa sürede kullanıma hazır olan tüm araçlarımızı bulabilirsiniz. Donanım Özeti: Tam donanım talep üzerine sunulmaktadır. Kaz Boynu * Ön tarafta yaklaşık 45° açılı köşelerle ve arka tarafta yaklaşık 750 mm x 10° açıyla eğimli kaz boynu * 3 çift bağlama halkası (LC 5.000 daN) * Yaklaşık 30 mm kalınlığında sert ahşap kaplama Çekilebilir Tasarımlı Yük Platformu * Arka tarafta yaklaşık 1.000 mm x 8° eğim * Dışa doğru katlanabilen 5 çift bağlama halkası (LC 5.000 daN) * Dışa doğru katlanabilen 3 çift bağlama halkası (LC 10.000 daN) * Yük platformunun ön tarafında yatay konumda 1 çift bağlama halkası (LC 10.000 daN) * Gergi bantlarının takılması için yük platformunun dış çerçevesinde oyuklar (LC 2.000 daN) * Aksların üzerinde çıkıntılı yüzeyli çelik levha kaplama ile yaklaşık 48 mm kalınlığında sert ahşap kaplama Akslar * BPW akslar ve süspansiyon * 1. aks sabit, diğer tüm akslar hidro-mekanik olarak zorunlu olarak yönlendirilir * Teknik aks yükü: her biri 12.000 kg * Kaldırma ve indirme valfli hava süspansiyonu * Aks aleti * Lastikler * 245/70 R 17.5 3PMSF * Yük indeksi (146/146 F) * TPMS: ECE R 141'e uygun TPMS lastik basıncı izleme sistemi Dorse Destekleri * Yaklaşık 24 ton kaldırma kapasitesi (yaklaşık 50 ton test yükü) için 2 vitesli şanzımana sahip JOST dorse destekleri (mekanik) Fren Sistemi * AB yönetmeliklerine uygun olarak EBS-E (4S3M) ile donatılmıştır Boya * Kaynak işleminden sonra tüm çelik yapı, otomatik olarak döndürme disk sistemi ile püskürtülerek temizlenir * Kaplama sisteminin optimum yapışması için korund ile ikinci temizleme işlemi * En iyi korozyon korumasını sağlamak için tüm araç şasisinin HRM metalizasyonu ile ZINACOR 850 (%85 çinko / %15 alüminyum) kaplama * 2 kat 2K üst kat boya ile son kat boyama * RAL 3002 Kırmızı renkte, RAL 841GL sistemine uygun tek renk * Jantlar gümüş gri renkte. Arka kısım metalize edilmiştir ve RAL 9010 (saf beyaz) renginde boyanmıştır * Metalik boya mümkün değildir * Boya uygulaması, ISO 9227-NSS tuz sisi püskürtme testinde test edilmiştir * Özel bir balmumu ile boşlukların kapatılması Çelik Yapı * Yüksek mukavemetli ince taneli çeliklerden yapılmıştır Dsdpfxozk S Dmo Aiwswb * Çelik kaliteleri: S355J2+N/S355MC (akma dayanımı 355 MPa) S690QL/S700MC (akma dayanımı 690 MPa) Elektrik Sistemi * AB yönetmeliklerine uygundur Aydınlatma * 24 Volt ASPÖCK-NORDIK (ASS3) * Tüm LED yan işaret lambaları, sinyal lambasıyla birlikte yanıp söner * Ön bağlantı panelinde 24N, 24S ve 15 kutuplu prizli ASPÖCK-UNIBOX * ISO'ya uygun bağlantı. 24N ISO-1185 24S ISO-3731 15 kutuplu ISO-12098 Aşağıdaki ek ekipmanlar dahildir * 2 inç Kral pim * Yaklaşık 400 mm yüksekliğinde galvanizli çelik ön duvar * Elektrikli-hidrolik ünite (± 45 kg) * Ön ve arka taraftan, kablo uzaktan kumandası aracılığıyla düğmelerle kontrol edilebilen takip direksiyonu, aksların tek şerit kontrolü ile (SZM'de kurulum olmadan) * Arka kısımda, eğimli kısımda, merkeze monte edilen taşıyıcı üzerinde yatay konumda 1 çift gömme bağlama halkası (LC 10.000 daN) (± 3 kg) * Kaz boynunda, takılabilir alüminyum yan ve arka duvarlar, yaklaşık 2.440 x 400 mm (U x Y) * Arka galvanizli takılabilir kirişler çıkarılabilir. (Yapının uzunluğu yaklaşık 2.560 mm) (± 46 kg) * Eğimli kaz boynunda entegre, galvanizli bir alet kutusu (± 47 kg) * Yük platformunda, 20' (30?) veya 40? konteyner için 3 çift WADER konteyner cebi (± 30 kg) * Yük platformunun dış çerçevesinde yaklaşık 100 x 50 mm boyutlarında 6 çift kiriş cebi (± 18 kg) * Her iki tarafta yaklaşık 23

Durum: yeni, boş ağırlık: 15.550 kg, azami yük ağırlığı: 47.450 kg, toplam ağırlık: 63.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimizing loading platform length, approx. 3,700 mm long - Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading Platform: - Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° - A recess in the loading platform as well as into the bevel for accommodating the excavator bucket arm - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood flooring on the bevel of the loading platform Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide - Ramps with hardwood covering - Hydraulically foldable ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outward and approx. 215 mm inward - Square climbing strips 20 x 30 mm, at approx. 200 mm intervals on the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, first axle steerable, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reverse lock, activated automatically in reverse gear and manually - Air suspension with lift and lower valve - Tires: 235/75 R 17.5 twin tires - TPMS tire monitoring system compliant with ECE R141 - TPMS tire sensors installed in all wheels, including spare wheels Accessories included: - Detachable front wall, steel, approx. 400 mm high - 3kW electro-hydraulic power unit for operating hydraulic functions, except hydraulic cable winch - Parking bracket for warning signs on gooseneck when not in use - 1 spare wheel - On the gooseneck: 1 pair of detachable ALU side boards, approx. 400 mm high, anodized - On the gooseneck: one detachable ALU rear board, approx. 400 mm high, anodized - Over the gooseneck: approx. 40 mm thick hardwood covering, checker plate covering above king pin - 2'' king pin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide - 4 wheel chocks - Mechanical landing gear with two-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - 1 intermediate table, approx. 300 mm wide Dwodpfxjk Aht Uj Aiwob - Telescopic width extensions (galvanized) approx. 230 mm per side - Wheel recesses with square climbing strips - ALU covers for the wheel recesses - 1 pair of mechanical rear supports - Remote steering from front and rear via cable remote control, with single track axle monitoring - 1st axle with automatic lifting axle function - Central lubrication system with 1 pump, BEKAMAX brand - Wireless remote control for remote steering, in addition to cable remote, with 2 indicator lights on receiver for single track monitoring - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for beacon

Durum: yeni, boş ağırlık: 13.500 kg, azami yük ağırlığı: 51.500 kg, toplam ağırlık: 69.500 kg, dingil konfigürasyonu: > 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 r17.5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck in SNT design for optimization of loading area length, length approx. 3,700 mm Gooseneck rear with bevel approx. 1,000 mm x 10° Loading Area: Telescopic loading area, length approx. 8,800 mm, with rear incline approx. 500 mm x 10° Recess in the incline and extending into the loading area for accommodating the excavator dipper stick Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected within the extendable beam and adjust to the respective loading area length Ramps: 1 pair of two-piece steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically adjusted individually approx. 235 mm outwards and 215 mm inwards Axles and Suspension: Djdpfx Aek Ahugoiwjwb BPW axles and suspension, two fixed axles, two steering trailing axles Electromagnetic reverse lock activated via reverse gear and manually Air suspension with lifting and lowering valve Axle tool Tyres: 235/75 R17.5 3PMSF twin tyres Load index: 143/141J (144/144F) Brake System: WABCO brake system, EBS-E according to EU regulations Lighting System: 24-volt lighting system, “ASPÖCK-NORDIK full LED” Metallization: Standard HRM metallization of the external frame Complete steel structure shot blasted, subsequently visible defined surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished Steel Structure: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified according to DIN-EN 287-1 MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included accessories: Removable steel front wall, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 Round NATO socket on the front connection strip Cable for supplying the electro-hydraulic pump and/or electric winch (35 mm², 3.5 m long) between trailer and tractor unit with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling hydraulic operations (except for hydraulic winches) 1 spare wheel with mounting adapter External beams on the gooseneck with mounting holes for bolt-on lashing rings, first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included Mounting hole on the upper rear of the gooseneck external beam for a screw-on lashing ring 1 pair screw-in lashing rings Approx. 40 mm thick hardwood floor above gooseneck On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized On the gooseneck, one plug-in aluminium rear wall, approx. 400 mm high, anodized 2" king pin Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide 4 wheel chocks with holders Provision for aluminium approach ramps Mechanical landing gears with 2-speed gearbox and crank On the loading area, continuous hardwood floor approx. 50 mm thick, interrupted only between the axles Load area locking with conically welded positioning profiles every 250 mm including pre-tension plate Slotted holes at the front of the loading area for attachable and repositionable bridging plates 1 intermediate table with recessed loading area, approx. 300 mm wide, for the large cross-section sliding tube with sheet metal covering Front and rear with longe...

Durum: yeni, azami yük ağırlığı: 36.040 kg, toplam ağırlık: 53.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Dwedpfsy Uwu Isx Aiwob Equipment excerpt. Full specification upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, approx. 3,750 mm long * Gooseneck hydraulically lift/lowerable and detachable * For tractor units: 6x4 or 8x4 Lowbed: * Lowbed with external beams, extendable in SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking * Supply lines are protected within the extendable beams and automatically adjust to the lowbed length * 7 pairs of lashing rings foldable outward (LC 10,000 daN) * 6 pairs of threaded blocks on the inner girder for mounting screw-on RUD rings Rear Undercarriage: * Rear chassis with closed outer frame and checker plate cover * Chassis with excavator trough, closed in the rear half to accommodate air tanks * 3 pairs of lashing rings foldable outward (LC 5,000 daN) * 1 pair of lashing rings foldable outward (LC 10,000 daN) * 1 pair of flat lashing rings, front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydromechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer of choice. Load index (146/146F) Brake System: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with 2 layers of 2K topcoat, single colour in RAL 3002 Carmine Red as per RAL system 841GL Including accessories: * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized connection bar at the front * Remote steering from front and rear via cable remote control with push buttons, including single-track axle control (without installation in the tractor unit) * Prepared for bolt-on container positioning for 1 x 20', 1 x 40', or 1 x 45' container on the outer beams. No container locks * Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings * Electro-hydraulic power unit * Spiral cable for supplying the electro-hydraulic power unit and/or electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between semi-trailer and tractor unit with plug connection (NATO-NATO) * Yellow reflective tape to EU regulations on sides, extension and rear of the trailer * At the gooseneck and rear, left and right, a bracket for warning signs including a socket * Manual and description on USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable guard around the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer beam for mounting screw-on RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above normal ride height, adjustable by hand control * On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (body length approx. 2,560 mm) * On the gooseneck, a separate air connection with air gun * 1 stainless steel toolbox, approx. 1,350 x 400 x 400 mm, mounted externally

Durum: yeni, azami yük ağırlığı: 40.017 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: > 3 aks, Üretim yılı: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading Area: 5 pairs of fold-out lashing rings (LC 5,000 daN). 3 pairs of fold-out lashing rings (LC 10,000 daN). 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN). Hardwood flooring approx. 48 mm thick, tread-plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 205/65 R17.5, manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface as per ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles: two fixed axles, two self-steering axles, air suspension, drum brakes, lifting/lowering function. The self-steering axles have electro-magnetic reverse lock, activated via reverse gear or manually. Axle tool included. Brake System: WABCO brake system compliant with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit. Dwjdow Dl Hqepfx Aiwob Electrical System: Electrical system as per EU regulations, 24 Volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights synchronise with the indicator. ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets. Connections in accordance with ISOs: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: Entire steel structure automatically shot blasted after welding using a shot blasting system. Second blasting treatment with corundum for optimum adhesion of the coating system. HRM metallisation of the complete chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection. Final painting: two coats of 2-pack topcoat, single-colour in a shade of choice according to the RAL 841GL system. Rear section metallised and painted in RAL 9010 (pure white). Metallic finishes not available. Paint specification tested according to salt spray test ISO 9227-NSS. Cavity sealing with special wax. Options Included: 2'' kingpin One galvanised steel front wall. Yellow-red air couplings fitted to the galvanised front connection rail. 2 wheel chocks with holders on the front wall. Mountings at the rear of the gooseneck for ALU ramps. Further options available.

Durum: yeni, azami yük ağırlığı: 36.400 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment list available upon request. Gooseneck in SNT design to optimize loading deck length, approx. 3,700 mm long, rear with chamfer approx. 1,000 mm x 6° * For tractor units: 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for controlling hydraulic operations, excluding hydraulic winches. Without installation of supply connections on the tractor unit * Outer beams of the gooseneck with mounting holes for boltable lashing rings. The first hole approx. 200 mm from the front, then every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * One mounting hole in the upper rear area of the gooseneck's outer beams for a bolt-on lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * 3 pairs of recessed lashing rings inside on the gooseneck's outer beam (LC 5,000 daN) * 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) * 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) * On the gooseneck and rear chamfer, grating surface with 5 mm steel reinforcement * 2-inch king pin * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m in length) between trailer and tractor unit with NATO-NATO plugs * On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized finish LOADING AREA: * Loading area, approx. 9,600 mm long, with rear chamfer approx. 900 mm x 6° * Loading area behind gooseneck hydraulically height-adjustable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axle fixed, 3rd axle steered. 3rd axle with electromagnetically controlled reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires. Make at our discretion, load index 143/141J (144/144F) * Mechanical landing legs with 2-speed gearbox and crank * Continuous grating surface with approx. 5 mm steel reinforcement underlay, designed for point loads: – on the lift bed – on the loading area * Painted sand coating on the deck plates of the gooseneck and in the transition areas between neck and lifting bed, between lifting bed and loading area, and between loading area and ramps * 1 spare wheel mounting bracket under loading area on right side in front of axles * Cut-outs in the outer frame of the loading area and lifting bed for securing straps (LC 2,000 daN) * 11 pairs of recessed lashing rings flush in the outer frame of the loading area, foldable outwards (LC 10,000 daN): – 3 pairs in the outer frame of the lifting bed – 8 pairs in the outer frame of the loading area * 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): – 3 pairs in the lifting bed – 8 pairs in the rear part of the loading area * Control valves for hydraulic ramps located on the right side of the vehicle * 1 pair of foldable mechanical rear supports with single-handed operation Dsdpfx Aijyhkquewjwb HYDRAULIC LOADING RAMPS: * 1 pair of two-part AXS steel ramps with a length of approx. 4,920 mm and a

Durum: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, 3-axle MULTIMAX PLUS low-loader semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross weight: 49,500 kg or 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Coupling height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: (value not specified) Loading area width approx.: 2,540 mm Loading height at max load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific legal limits are exceeded. Technical Description Gooseneck: SNT design gooseneck to optimize loading platform length, approx. 3,900 mm length, with rear chamfer approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading area: Loading platform approx. 9,600 mm length with rear chamfer approx. 900 mm x 6°. Section after the gooseneck is hydraulically raisable/lowerable, approx. 3,000 mm long, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS Pair of two-section AXS steel ramps, approx. 4,920 mm long and 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Each ramp hydraulically shiftable approx. 235 mm outward and approx. 365 mm inward. Maximum load and ramp angle as per technical datasheet: C470319. Maximum gradient at lowered loading area: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg. Air suspension with lift/lower valve. Axle tools included. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion. Load index 143/141J (144/144F). Braking system: WABCO EBS-E braking system per EU regulations. No cables to the tractor unit. Lighting system: 24V "ASPÖCK-NORDIK full LED" lighting per EU regulations (ASS 3). Metallisation: Complete HRM (High Resistance Metallisation). Full steel structure shot-blasted, then hot-coated with ZINACOR 850 (85% zinc / 15% aluminium). Painting – 6-stage finish: - Complete steel structure shot-blasted after welding - 1 coat zinc-based primer, 1 coat adhesion primer - Top coat with 2 coats 2K acrylic paint, single colour in RAL shade of choice - Cavity sealing with special wax - Rims in silver - Multicolour & special paint available at extra cost Steel structure: High-tensile fine-grain steels Types: S355J2+N/S355MC (yield stress 355 MPa), S690QL/S700MC (yield stress 690 MPa) Welders certified to DIN-EN 287-1, MAG welding per EN ISO 4063, M21 shielding gas as per EN ISO 14175. Front wall: Removable steel front wall, approx. 400 mm high. Supply connection strip for connections to tractor unit, fitted at outer frame profile height. ASPÖCK-UNIBOX at the front supply strip with 24N, 24S & 15-pin sockets. - 24N connection per ISO-1185 - 24S connection per ISO-3731 - 15-pin connection per ISO-12098 If your pin assignment deviates from the ISO standard, please inform us. Dedpeizu Ntjfx Aiwewb "Anderson" socket on front supply strip: Rema 78051-00 & Amp. 150 V. Cable for the supply of the electro-hydraulic power pack and/or electric winch (35 mm²,

Durum: yeni, boş ağırlık: 10.350 kg, azami yük ağırlığı: 39.150 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.300 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - 1 pair of fixed built-in wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm - Wheel recesses equipped with 15 x 15 mm square climbing strips and lower-section extensions - 1 pair of fixed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm - 3-part removable galvanized covers over wheel recesses (W 670 mm) – max. point load 5 t / pc. - Recess in the ramp and extending into the load area to accommodate an excavator bucket arm approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm depression (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) One-piece ALU ramps: - One pair of single-piece ALU ramps approx. 2,500 x 600 mm - Ramps with spring assist and manual lateral adjustment - Maximum load per pair: 24,000 kg Axles and Tyres: - BPW axles and suspension, 2 rigid axles, 1 self-steering axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with raise/lower valve - Axle tools - Tyres 235/75 R 17.5 - TPMS (Tire Pressure Monitoring System) in compliance with ECE R 141 Accessories included: - One spare wheel with bracket in front of the bulkhead - 2" kingpin - One galvanized steel bulkhead ca. 400 mm high - Yellow-red air couplings at the galvanized front coupling strip Dodpoiu Er Asfx Aiwewb - 4 chocks with bracket at the bulkhead - Accommodation at the rear of the gooseneck for ALU approach ramps - Galvanized extensions, extendable approx. 230 mm per side - Galvanized folding supports under the rear incline of the loading area - Bracket for a rotating beacon at the rear of the trailer - White reflector tape in accordance with EU requirements on sides, red on extension and rear - On the gooseneck and rear panel, bracket for warning boards including socket, left and right - On the gooseneck, plug-in ALU side walls and rear wall approx. 2,440 x 400 mm - Removable rear galvanized stanchions (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the load area for a 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area - One removable galvanized intermediate table with 1 pair WADER container pockets - 20 x 20 mm square climbing strips every 200 mm along the outer frame of the loading area's rear incline - Non-slip sand coating painted onto the checker plate on the gooseneck and loading area - Four warning boards extendable by approx. 400 mm each, approx. 423 x 423 mm with position light - Bracket for rotating beacon on warning boards - 80 km/h speed stickers on the rear and both sides - Load gauge for axle load determination including load chart - HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then defined visible surfaces metallically finished with ZINACOR 850 (Zinc 85% - Alu 15%) hot metalized

Durum: yeni, boş ağırlık: 9.300 kg, azami yük ağırlığı: 38.700 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 1.200 mm, süspansiyon: hava, lastik boyutu: 385/65 R 22,5, renk: gri-siyah, Donanım: ABS, Loading Platform: • Loading platform in extendable design with pneumatically operated locking mechanism • Loading platform with approx. 30 mm thick wooden floor • 7 pairs of outward-folding lashing rings (LC 5,000 daN) • 3 pairs of outward-folding lashing rings (LC 10,000 daN) • Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles and Tyres: • BPW axles and suspension, all axles hydro-mechanically forced steered • Equipped with disc brakes • Technical axle load: 10,000 kg • Air suspension with raise/lower valve • Axle tools • Tyres: 385/65 R 22.5 • TPMS (Tyre Pressure Monitoring System) according to ECE R 141 Dodpfxoiu Etrs Aiwowb Brake System: • WABCO brake system compliant with EU regulations, with EBS-E (2S2M) Electrical System: • Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) • ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin • Connections according to ISO standards • 24N ISO-1185 • 24S ISO-3731 • 15-pin ISO-12098 Accessories Included: • Remote-controlled steering from front and rear via cable remote with push-button operation, including single-track monitoring of axles • 4 wheel chocks with holders mounted on the front wall • 2" kingpin • One galvanized steel front wall approx. 1,600 mm high • Yellow-red air couplings mounted on the galvanized front connection bar • White reflective tape according to EU regulations on the sides, at extension and at the rear of the trailer in red • European reflective plates (red-yellow) on the rear of the trailer • One mudflap at the rear of the trailer • Manual and description • Mounting bracket for a beacon at the rear of the trailer • Loading platform with approx. 30 mm thick wooden floor enclosed in omega profiles • 10 pairs of stake pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform • 1 spare wheel holder under the right side of the loading platform in the direction of travel • Electro-hydraulic unit • On the gooseneck and rear apron left and right, each with a bracket for warning boards including socket • Painted sand layer for anti-slip protection on the main beam • 6 pairs of WADER container locks on the loading platform, for 1x20ft, 2x 20ft, or 1x 40ft container; in the extension, an additional locking position is provided for a 45ft container • 4 pairs of crosswise mounted stake pocket bars on the loading platform for plug-in stanchions 100 x 50 mm • Access ladder mounted on the right in the direction of travel • One HDPE toolbox approx. 1,200 x 500 x 480 mm in front under the loading platform on the left in the direction of travel • BEKAMAX central lubrication system (Pico) with removable pump guard • Lift axle on the front axle controlled by TEBS E depending on current axle load and loading condition • Wireless remote control for the rear steering in addition to the cable remote, with indicator lights on the receiver for single-track monitoring • Four extendable warning plates approx. 400 mm extension, size approx. 423 x 423 mm with position light • Bracket for beacon on the warning plates • 80 km/h speed stickers on the rear and both sides • Load pressure gauge to determine axle loads, including load diagram • HRM metallization (High Resistance Metallisation) of the outer frame • Complete steel construction shot-blasted, then the defined visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Durum: yeni, azami yük ağırlığı: 96.500 kg, toplam ağırlık: 126.000 kg, dingil konfigürasyonu: > 3 aks, yükleme alanı uzunluğu: 26.900 mm, toplam genişlik: 2.750 mm, Donanım: ABS, Our complete range of vehicles, including those available immediately and at short notice, can be found on our website. Excerpt from the equipment features. Full equipment details available on request. Gooseneck: * Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm * For tractors: 6 x 4 or 8 x 4 * Truck hydraulic connection with flow regulator (20 l/min), including gallows for suspension of supply lines. The tractor's tank must have a minimum capacity of 80 L * With MAX Trailer couplings, otherwise coupling parts to be supplied ex works by the customer * Gallows with winch for spare wheel located at the front of the gooseneck * 3.5 inch kingpin * Steel front wall approx. 400 mm high * Plug-in aluminium side and rear boards for the gooseneck, approx. 400 mm high, anodized finish * Operating levers on the gooseneck protected by a foldable cover * Illuminated controls at the gooseneck, with on/off switch * One 7-pin socket left and right at the rear of the gooseneck for warning sign * BEKA-MAX central lubrication system for a gooseneck using standard grease NLGI-2 * Hydraulic couplings from gooseneck to lowbed deck with screw-type couplers * Access steps to the gooseneck Dwjdpfx Aezahp Sjiwob * Four warning panels extendable approx. 1,000 mm, approx. 423 x 423 mm, with one LED marker light and bracket for rotating beacon * Mounting adapter for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Output: 9.5 kW (12.9 HP) at 3,000 rpm * Hydraulic connection lines between the power pack and the connector plate at the gooseneck * One LED work light left and right at the rear plate of the gooseneck with separate on/off switches * Radio remote control: - Operation of the power pack, start/stop of the diesel engine. - Operation of steering, in addition to cable remote control, with 2 LED indicators on the receiver for single-track monitoring. - Operation of raising/lowering the gooseneck. - Operation of raising/lowering suspension of running gear. 2-Axle Front Bogie: * Pin-eye coupling front and rear. Length: approx. 2,970 mm; bogie width: approx. 2,750 mm * BEKA-MAX central lubrication system for a 2-axle bogie with standard grease NLGI-2 (not connected to the tie rods) * One 7-pin socket left and right at the rear of the front bogie for warning panels * Bogie surface finished with painted-in sand coating for slip-resistance * Yellow reflective tape according to EU regulations on the side, at extension and at the rear of the trailer * One 7-pin socket for warning panels, left and right at the front bogie, in the axle area * Extendable extensions of approx. 230 mm per side for a 2-axle bogie * 1 pair of M42 threaded blocks between the axles of the front bogie * 1 pair of brackets for warning panels to be inserted into the stake pockets on the outer frame of the load bed Load Bed: * 6-axle, double telescopic load bed with pin-eye coupling at the front and a rear bevel of approx. 500 mm x 8° * Load bed length: approx. 11,000 mm * Technically extendable by approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Standard width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the load bed with standard grease NLGI-2 * Load bed surface finished with painted-in sand coating for slip-resistance * 11 pairs of recessed lashing rings in the outer frame of the load bed, foldable outwards (LC 10,000 daN) * Permanently welded intermediate platform, approx.

Durum: ikinci el, renk: yeşil, Üretim yılı: 2018, Faymonville F-S42-2ACB. Yıl: 2018. 12 tonluk Pendel-X akslar. Maksimum ağırlık: 49.000 kg. Çekme çubuğu yükü: 25.000 kg. Hidrolik, sökülebilir kuğu boynu. Hidrolik sistem, bir kamyondan NATO standardında çalışır. EBS ABS ALB. Yedek lastik. Hidrolik süspansiyon. Kablo üzerinden uzaktan kumanda. Boyun kısmında alüminyum levhalar + alet kutusu. 5,5 metre uzatılabilir. 2 x 25 cm genişletilmiş. Ekskavatör köprüsü: 2750x600 mm. Dsdpfx Ajzybbysiwjwb Çinko kaplamalı. Ölçüler: Boyun: U: 3650 mm. G: 2500 mm. Y: 1550 mm. Çekme çubuğu yüksekliği: 1250 mm. Zemin: U: 8000 mm. G: 2550 mm. Y: yaklaşık 350 mm. Zemin kalınlığı: 220 mm. Arka kısım: U: 2750 mm. G: 2550 mm. Y: 1000 mm. Lastikler: 245/70R17,5 %80. Alman yapımı dorse! ID No: 465. Heinhuis'in Genel Hüküm ve Koşulları, Heinhuis tarafından yapılan tüm reklamlar, teklifler ve fiyatlandırmalar, Heinhuis tarafından yapılan tüm sözleşmeler ve bunların öncesindeki müzakereler için geçerlidir. Herhangi bir şekilde verilen yanıtla, Heinhuis'in Genel Hüküm ve Koşullarının geçerliliğini kabul etmiş ve bu Genel Hüküm ve Koşulları okuduğunuzu beyan etmiş olursunuz. Fiyatlarımız, ihracat için geçerli net fiyatlardır. = Ek Bilgiler = Üretim Yılı: 2018 Toplam izin verilen ağırlık: 49.000 kg Uzatılabilir üst yapı: Evet = Şirket Bilgileri = Daha fazla bilgi için:

Durum: yeni, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Gross weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Loaded saddle height: 1,200 mm Rear steering radius: 2,300 mm Loading platform length: 6,850 mm Extendable by: 5,500 mm Loading height at maximum load: 350 mm Chassis length: 2,600 mm Rear chassis loading height at max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Overall width: 2,540 mm Gross weight depends on fifth wheel load. Lowbed: Lowbed with external beams, extendable version "SUPER LOW" design, length approx. 6,850 mm. Lowbed with fixed hardwood floor approximately 40 mm thick and mechanical locking device. Supply lines are protected inside the extendable beams and automatically adjust to the respective lowbed length. 5 pairs of lashing rings, foldable outward (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear chassis: Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at rear. 2 pairs of lashing rings, foldable outward (LC 10,000 daN). 1 pair of lashing rings, flat in the trough (LC 8,000 daN + 5,300 daN). 2 pairs of pocket sockets for stanchions 100 x 50 mm in the external frame. Gooseneck: Gooseneck in SNT design to optimize usable platform length, length approx. 3,785 mm. Gooseneck hydraulically lift/lowerable and detachable. Technical fifth wheel load: 23,000 kg For tractor units: 4x2, 6x2, and 6x4 PENDLE-AXLE: “PENDLE-AXLE”, all axles hydro-mechanically forced steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and plug pins for securing in raised position. Axles finished with two coats of 2-component paint, single color "FAY-Grey-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tools. Brake system: Brake system in accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit. Electrical system: Electrical system according to EU regulations, 24V lighting ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection strip with 24N, 24S, and 15-pin sockets. Connection according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel construction: Steel construction made of high tensile fine-grained steels. Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Painting: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer. Premium two-component (2K) topcoat in one RAL color of your choice. Rear section metallized and painted in RAL 9010 (Pure White). No metallic paint possible. Tyres: Tyres 245/70 R 17.5 3PMSF Dwjdoizu Nwjpfx Aiweb Manufacturer’s choice. Load index (146/146F). Prepared for fitting of bolt-on container positions for 1x 20' or 1x 40' container on the external beams. Without container locks. • 2” king pin • Galvanized steel front wall approx. 400 mm high • 1 spare wheel with holder in front of the front wall • 2 wheel chocks with holder on the front wall • Yellow-red air couplings on the galvanized connection strip at the front. Remote steering from front and rear via cable remote control with pushbuttons, with single-track axle monitoring (without installation in the tractor unit). Hydraulic connections from the gooseneck to the lowbed

Durum: yeni, toplam ağırlık: 80.000 kg, dingil konfigürasyonu: > 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, Additional vehicles available – extract from equipment list. Full equipment details upon request. GOOSENECK: * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, rear with chamfer approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, detachable, approx. 400 mm high * ASPÖCK-UNIBOX on the front control panel with 24N, 24S & 15-pin sockets * 3 kW electric-hydraulic power pack for controlling hydraulic functions, excluding hydraulic winches * Outer beams of the gooseneck with mounting holes for bolted lashing rings: first hole approx. 200 mm from the front, then every approx. 400 mm; 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings in the rear of the gooseneck (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in ALU sideboards, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood flooring over the gooseneck, over king pin checker plate covering * 3.5 inch king pin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO plug socket on the front control panel (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retaining spring suspended on the outer beams of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, approx. 8,800 mm long with rear chamfer approx. 500 mm x 10° * Pneumatic locking with conical locking pin and reinforced locking positions; supply lines are protected within the extendable beams and automatically adapt to the platform length * BPW axles and suspension, 1st axle with steering, all other axles hydro-mechanically forced steering * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tyres – brand at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B – static test load = 50,000 kg * On the platform, continuous and between axles interrupted approx. 50 mm thick hardwood flooring (thereby increasing the coefficient of friction). – Slotted holes for hook-in and repositionable bridging elements * At front of platform – 1 adjustable intermediate table, approx. 300 mm wide, for the extension tube with large cross-section, with checker plate covering. – Front and rear with slotted holes for hook-in and repositionable bridging elements * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 7 pairs of recessed, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extensions (galvanized) extendable by approx. 230 mm on each side (without wooden planks) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation in tractor unit * TPMS tire pressure monitoring sensors installed in all wheels * Platform locking with conically welded locking profiles every 500 mm * Locking control left and right on the trailer * For the intermediate table, approx. 300 mm wide, a mechanical lock to secure the table to the extension Dwodpoxarmajfx Aiwsb * 5 pairs of threaded blocks on the extendable beam for mounting bolt-on rings M20 (LC 5,000 daN) BRAKE SYSTEM

Durum: yeni, azami yük ağırlığı: 38.953 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Gross vehicle weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading platform length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Steering angle radius (rear): 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck: Gooseneck with chamfered front corners at 45° and rear taper of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8°. 6 pairs of folding lashing rings facing outward (LC 5,000 daN). 2 pairs of folding lashing rings facing outward (LC 10,000 daN). 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN). Cut-outs in the outer frame of the loading platform for attaching tensioning straps. (LC 2,000 daN). Dwodpfxsg Sk Tro Aiwjb Hardwood flooring approx. 48 mm thick, above the axles fitted with chequer-plate covering. Ramps: Two-piece steel ramps: One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically foldable ramp sections, hydraulic lifting device and can be hydraulically adjusted laterally. Maximum load per pair: 40,000 kg Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R 17.5 tyres as per manufacturer's selection. Axles: SAF axles, air-suspended, with drum brakes, featuring lift/lower function. Last axle is force-steered with electro-magnetic reverse lock, activatable via reverse gear or manually. Axle tools. Brake System: Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit. Steel Construction: Steel construction made from high-strength fine-grained steel. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: Premium and durable corrosion protection via sandblasted welded frame, primed with 2-component (2K) zinc dust primer. High-quality single-tone 2-component (2K) top coat in RAL colours of your choice. Rear metalized and painted in RAL 9010 (pure white). Metallic paint not possible. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets. ISO-compliant connections. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories Included 2" king pin One galvanized steel front bulkhead approx. 400 mm high. At the galvanized front connection strip yellow/red airline couplings. 4 wheel chocks with holder on the front bulkhead (± 5kg). Cable for supplying electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long, max. 250A) between semi-trailer and tractor unit, with plug connection (ANDERSON-ANDERSON). Galvanized folding supports under the rear slope of the loading platform. Bracket for a rotary beacon at the rear of the trailer. Control valves for the ramps installed on right-hand side of trailer (± 4kg). Yellow reflective tape according to EU regulations on the sides and rear of the trailer. Electro-hydraulic unit mounted at the rear under the loading

Durum: yeni, azami yük ağırlığı: 90.700 kg, toplam ağırlık: 126.000 kg, dingil konfigürasyonu: > 3 aks, toplam genişlik: 2.850 mm, Donanım: ABS, You can find our complete inventory of immediately and shortly available vehicles on our website. Excerpt from the equipment list. Complete specification available on request. Gooseneck: Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. For tractor units: 6 x 4 or 8 x 4 3-axle compact front bogie: * Hook coupling at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Low bed: * ATX-A low bed with telescoping longitudinal beams in low-floor design with fixed hardwood floor, approx. 50 mm thick * Equipped with drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance of approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for mounting a low bed at the front, end cross member at the rear * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLE, all axles hydro-mechanically steered * Hose rupture valve on the axle equalizer cylinder with automatic RESET function * Hydraulic cylinder with shut-off valves and positioning pins for safety in raised position * Final painting of axles with two coats 2K paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x as per manufacturer's choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLE, all axles hydro-mechanically steered * Hose rupture valve on the axle equalizer cylinder with automatic RESET function * Hydraulic cylinder with shut-off valves and positioning pins for safety in raised position * Final painting of axles with two coats 2K paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x as per manufacturer's choice (M+S) 285/70 R19.5, load index 150/148J Paint finish: * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure maximum corrosion protection * Final coat with two layers of 2K topcoat, single color in RAL 3002 Carmine Red, according to the RAL 841GL system Includes accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU side walls and rear wall for the gooseneck, approx. 400 mm high, anodized version * 3.5" king pin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * Front bogie with a separate air connection for pneumatic tools * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for the installation of bolted container positions for either 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Brackets on the outer beams of the loading platform for attaching foldable extensions * One 7-pin socket left and right, front and rear, on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control for rear axle steering * Rear bogie with trough Dwjdpfx Aew Tgp Doiwjb * 2 LED reversing lights mounted on the rear plate * European reflective signs (red-yellow) at the rear * One mudflap at the rear * One LED beacon with bracket left and right on the end cross member * Two INOX toolboxes 855 x 340 x 390 mm mounted left and right on the gooseneck * 1-cycle

Durum: ikinci el, azami yük ağırlığı: 36.515 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 05/2023, bir sonraki muayene (TÜV): 05/2027, Donanım: ABS, Donanım Özeti Dodpjzqiiajfx Aiwowb * Kuğu Boynu: Ön tarafta yaklaşık 45° açılı köşeleri olan kuğu boynu, arka tarafta yaklaşık 750 mm x 10° açılı. 3 çift bağlama halkası (LC 5.000 daN). Yaklaşık 30 mm kalınlığında sert ahşap kaplama. * Uzatılabilir Platformlu Yükleme Alanı: Arka tarafı yaklaşık 1.000 mm x 8° açılı uzatılabilir platformlu yükleme alanı. Dışa doğru katlanabilen 5 çift bağlama halkası (LC 5.000 daN). Dışa doğru katlanabilen 3 çift bağlama halkası (LC 10.000 daN). Yükleme alanının ön tarafında yatay konumlandırılmış 1 çift bağlama halkası (LC 10.000 daN). Akslar üzerinde tırtıklı sac kaplama bulunan yaklaşık 48 mm kalınlığında sert ahşap kaplama. * Akslar: BPW akslar ve süspansiyon, tüm akslar hidro-mekanik olarak zorunlu tekerlek yönlendirmesine sahiptir. Teknik aks yükü: her biri 12.000 kg. Kaldırma ve indirme valfli hava süspansiyonu. Aks anahtarı. * Lastikler: 245/70 R 17.5 3PMSF lastikler, yük endeksi (146/146 F) - seçimimize göre üretici. * Dorse Destek Ayakları: Yaklaşık 24 ton kaldırma kapasitesi (yaklaşık 50 ton test yükü) için 2 vitesli şanzımana sahip JOST dorse destek ayakları (mekanik). * Fren Sistemi: AB düzenlemelerine uygun fren sistemi, EBS-E (2S2M), dorse çekiciye bağlantı hatları olmadan. * Boya: Standart olarak bilye ile temizlenen kaynaklı şasi üzerine uygulanan birinci sınıf ve dayanıklı korozyon koruması, 2 bileşenli (2K) çinko tozu astar ile garanti edilmiştir. Yüksek kaliteli 2 bileşenli (2K) tek renkli RAL 3002 karmin kırmızısı üst kaplama. Arka kısım metalik boyalı ve RAL 9010 (saf beyaz) renginde boyanmıştır. Metalik boya mümkün değildir. * Çelik Yapı: Yüksek mukavemetli ince taneli çeliklerden yapılmış çelik yapı. Çelik kaliteleri: S355J2+N/S355MC (akma gerilmesi 355 MPa), S690QL/S700MC (akma gerilmesi 690 MPa). * Elektrik Sistemi: AB düzenlemelerine uygun elektrik sistemi, aydınlatma 24 Volt ASPÖCK-NORDIK (ASS3), ön bağlantı şeridindeki ASPÖCK-UNIBOX üzerinde 24N, 24S ve 15 kutuplu prizler. ISO standardına göre bağlantı. 24N ISO-1185, 24S ISO-3731, 15 kutuplu ISO-12098. * Aşağıdaki Ek Donanımlar Dahildir: * 2 inç König bağlantı pimi * Yaklaşık 400 mm yüksekliğinde galvanizli çelik ön duvar. * Galvanizli ön bağlantı şeridinde sarı-kırmızı hava bağlantı rakorları. * Ön duvarda bulunan 4 adet fren ayağı (± 5 kg). * Ön duvarın önünde bulunan bir yedek lastik tutucu. * Elektro-hidrolik güç ünitesi (± 45 kg). * Önden ve arkadan kablolu uzaktan kumanda ile basınç düğmeleri aracılığıyla kontrol edilebilen takip yönlendirmesi (dorse çekicisine kurulum olmadan), aksların tek şerit kontrolü ile. * Kuğı boynunun arka kısmında alüminyum rampalar için yuva. * Dorse üzerindeki arka kısımda bulunan Avrupa yansıtıcı tabelaları (kırmızı-sarı). * AB düzenlemelerine uygun olarak yanlarda, uzatılabilir kısımda ve dorsenin arkasında bulunan sarı yansıtıcı şerit. * Kuğu boynunda ve arka sac üzerinde, sol ve sağ tarafta, uyarı işaretleri için birer tutucu ve priz. * Dorsenin arka kısmında bulunan bir döner lamba tutucu. * Yükleme alanının eğiminin altında bulunan galvanizli katlanabilir destek ayakları. * Dorsenin arka kısmında bulunan bir çamurluk. * USB bellek üzerinde kullanım kılavuzu ve açıklama. * Arka ve yanlarda bulunan 80 km/s hız etiketi. * Aks yüklerini belirlemek için yük diyagramı ile birlikte yük göstergesi.

Durum: yeni, boş ağırlık: 15.420 kg, azami yük ağırlığı: 61.080 kg, toplam ağırlık: 76.500 kg, dingil konfigürasyonu: > 3 aks, yükleme alanı uzunluğu: 8.600 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 900 mm, lastik boyutu: 235/75/r17,5, renk: gri, Donanım: ABS, Gooseneck: Gooseneck with rear bevel approx. 750 mm x 10° 3 pairs of lashing rings 30 mm thick hardwood flooring Load area: Extendable load area with rear bevel approx. 500 mm x 8° 8 pairs of outward folding lashing rings 1 pair of flat-fitted lashing rings at the front of the load area Recesses in the outer frame of the loading area for attaching tie-down straps Approx. 48 mm thick hardwood flooring, checker plate covering above the axles Two-piece steel ramps: One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramp sections hydraulically lift and fold, hydraulically height-adjustable, and hydraulically shiftable. Maximum load per pair: 50,000 kg. Landing legs: • JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and tires: BPW axles and suspension, 4th and 5th axles steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lockout, activated via reverse gear and manually Tires 235/75 R 17.5 3PMSF Braking system: Braking system according to EU regulations with EBS-E (4S3M) Sockets and lighting: Dsdpfx Aiel Sl Izewjwb Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector rail with sockets 24N, 24S & 15 pin Connection compliant with ISO: 24N ISO-1185 24S ISO-3731 15 pin ISO-12098 Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component (2K) zinc dust primer High-quality 2-component (2K) topcoat, single color MB 7350 Novagrau Rear part metalized and painted in RAL 9010 (pure white) No metallic paint possible Steel construction: Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Accessories: One spare wheel with holder in front of bulkhead 2" kingpin One galvanized steel front wall, approx. 400 mm high Yellow-red air couplings mounted on the galvanized connector rail at the front 2 wheel chocks with holder on the front wall Bracket at rear of gooseneck for ALU drive-on ramps One holder for a rotating beacon at the rear of the trailer Galvanized supports beneath the rear bevel of the loading area White reflector tape according to EU regulations on the sides, extension, and rear in red Electro-hydraulic unit at rear under the loading area Mounts for warning signs with socket at the gooseneck and rear plate left and right Ramp control valves fitted to right-hand side of the trailer One mud flap at the rear of the trailer Manual and documentation on USB stick 3.5" kingpin supplied loose Plug-in ALU sideboards and rear wall on the gooseneck approx. 2,440 x 400 mm (LxH) Rear galvanized drop-in stakes are removable (structure length approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or 40' container 6 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area Galvanized extensions, extendable by approx. 230 mm per side Lifting axle on the front axle with control via TEBS E, depending on the current axle load and current loading condition Square cleats 20 x 20 mm every 200 mm on the outer frame of the loading area's bevel On the checker plates, above the kingpin and the loa...

Durum: yeni, boş ağırlık: 14.350 kg, azami yük ağırlığı: 53.450 kg, toplam ağırlık: 67.800 kg, dingil konfigürasyonu: > 3 aks, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.540 mm, yükleme alanı yüksekliği: 860 mm, süspansiyon: hava, lastik boyutu: 235/75 R 17,5, renk: gri, Donanım: ABS, hidrolik arka platform, Gooseneck: - Gooseneck in SNT design to optimize the loading deck length, length approx. 3,700 mm - Gooseneck rear with chamfer approx. 1,000 mm x 10° - Suitable for tractor units: 6x2, 6x4, 8x4 short Loading Platform: - Loading platform with extendable design, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° - Recess in the loading platform as well as extending into the chamfer for accommodating the excavator dipper stick, approx. 3,850 x 750 x 210/290 mm Two-Part Steel Ramps: - One pair of two-part steel ramps, each approx. 4,350 mm long and approx. 900 mm wide - Ramps with rubber covering - Ramps can be hydraulically adjusted individually approx. 235 mm outward and approx. 215 mm inward - "Super Grip" rubber flooring 25 mm and steel plate flooring approx. 5 mm as additional reinforcement on the chamfer of the platform - Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles, suspension, and tires: - BPW axles and suspension, 1st axle steered, all other axles forced steered hydromechanically - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, can be activated via reverse gear and manually - Air suspension with lifting and lowering valve - Tires 235/75 R 17.5 - TPMS tire pressure monitoring system compliant with ECE R141 - TPMS tire pressure sensors fitted on all wheels including spare wheels Surface Treatment: - Complete steel construction automatically shot-blasted with blasting machine after welding - Second blasting process with corundum for optimal adhesion of the coating system - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure best possible corrosion protection Dsdpfx Asya E A Nsiwewb - Final coating with 2 layers of single-color 2-component topcoat in MB 7350 Novagrau Included Accessories: - Steel front wall, plug-in, approx. 400 mm high - 3kW electric-hydraulic power unit for hydraulic controls, except for hydraulic winches - 1 spare wheel - External beam on gooseneck with mounting holes for screwable lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear area of the gooseneck - On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized - On the gooseneck, 1 plug-in ALU rear board, approx. 400 mm high, anodized - Approx. 40 mm thick hardwood floor on the gooseneck, checker plate at the king pin area - 2" king pin - Round NATO socket at the front connector strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front cross beam - 8 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outward - Extensions (galvanized) extendable by approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm, continuously open in front of the axles up to the cross beam of the gooseneck, approx. 700 x 410 mm - Wheel recesses with square climbing strips, 15 x 15 mm, between the 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - ALU covers for the wheel recesses, also usable as bridging elements for the extension or as extension beams - 1 pair of mechanical rear supports - Remote control (radio and cable) - Lifting axle at the front axle - Square climbing strips 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board system - 4 warning boards, approx. 423 x 423 mm

Durum: yeni, azami yük ağırlığı: 34.104 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2026, Further information here: Dodpfov D Abgox Aiwjwb

Durum: yeni, azami yük ağırlığı: 44.000 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2026, Further information here: Dsdpfov D Abtjx Aiwswb

Durum: ikinci el, renk: yeşil, Üretim yılı: 2015, Faymonville F-S44-1ACA. Yıl: 2015. 10 tonluk SAF akslar. Dwsdjzyb E Sepfx Aiwsb Ağırlık: 22.250 kg. Yük kapasitesi: 57.750 kg. Maksimum ağırlık: 80.000 kg. Çekme çubuğu yükü: 40.000 kg. EBS ABS ALB. Hidrolik sistem, kamyondan NATO bağlantısı üzerinden çalışır. Kuğu boynu üzerinde Allu plakalar bulunur. Hidrolik olarak sökülebilir kuğu boynu. Hava süspansiyonu. 5 metre uzatılabilir. Radyo ile uzaktan kumanda. Kazıcı köprüsü: 5600 mm x 950 mm. Lastikler: 235/75R17,5 %80. Ölçüler: Boyun: U: 4900 mm. G: 2500 mm. Y: 1800 mm. Çekme çubuğu yüksekliği: 1300 mm. Zemin: U: 8000 mm. G: 2750 mm. Y: 500 mm. Zemin kalınlığı: 300 mm. Arka kısım: U: 5600 mm. G: 2750 mm. Y: 1050 mm. Dolly D-2. Yıl: 2015. 10 tonluk SAF akslar. Ağırlık: 3650 kg. Maksimum ağırlık: 36.100 kg. Çekme çubuğu yükü: 16.100 kg. Hava süspansiyonu. Lastikler: 235/75R17,5 %70. Alman römorku! 4 adet mevcuttur! ID No: 484. Heinhuis'in Genel Şartlar ve Koşulları, Heinhuis tarafından yapılan tüm reklamlar, teklifler ve fiyat teklifleri, Heinhuis tarafından yapılan tüm sözleşmeler ve bu sözleşmelere öncülük eden görüşmeler için geçerlidir. Herhangi bir şekilde verilen yanıtla, Heinhuis'in Genel Şartlar ve Koşullarının geçerliliğini kabul etmiş olursunuz ve bu Genel Şartlar ve Koşullarının içeriğini okuduğunuzu beyan edersiniz. Fiyatlarımız, ihracat için geçerli net fiyatlardır. = Daha fazla bilgi = Üretim yılı: 2015 Boş ağırlık: 22.250 kg Yükleme kapasitesi: 57.750 kg Toplam ağırlık: 80.000 kg Uzatılabilir yapı: Evet = Firma bilgileri = Daha fazla bilgi için:

Durum: yeni, boş ağırlık: 22.700 kg, azami yük ağırlığı: 79.300 kg, toplam ağırlık: 102.000 kg, dingil konfigürasyonu: > 3 aks, yükleme alanı uzunluğu: 11.000 mm, yükleme alanı genişliği: 2.850 mm, yükleme alanı yüksekliği: 920 mm, lastik boyutu: 245/70 R 17.5, renk: gri, işletme ağırlığı: 22.700 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading deck length, approximately 3,750 mm long, with rear tapering of about 850 mm x 10° - Hydraulically liftable and lowerable, stroke ± 250 mm including hydraulic connection linked to the hydraulic axle compensation of the first two axles - Open in the rear third - For tractor units: 6x4 and 8x4 Loading Platform: - Extendable loading platform, length approx. 11,000 mm with rear taper approx. 500 mm x 10° - A recess in the platform and into the taper for accommodating the excavator bucket arm, approx. 4,240 x 900 x 440 mm - Pneumatic locking with conical locking bolt and reinforced locking positions; supply lines are protected in the extendable beams and automatically adapt to the respective platform length Ramps: - One pair of two-part steel ramps, approx. 4,650 mm long and approx. 900 mm wide - Hydraulically folding ramp tips - Ramps individually hydraulically adjustable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" rubber flooring 25 mm and approx. 5 mm steel flooring as additional reinforcement on the tapered section of the platform - Square climbing strips 20x30 mm, spaced approx. every 200 mm on the outer frame of the ramp Axles, Suspension and Tyres: - PA-X axle system, all axles forced steered hydro-mechanically - Steering behavior of the first two axles can be optimally adjusted to the platform length both mechanically and hydraulically - Hose rupture valve on the axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and pilot pin for securing in raised position - 245/70 R 17.5 3PMSF Accessories Included: - Removable steel front wall, approx. 400 mm high - Supply line connection strip to tractor unit, mounted at the height of the outer frame profile - 1 spare wheel - Outer beams of the gooseneck with mounting holes for screwable lashing rings - The first hole approx. 200 mm from the front, then spaced approx. every 400 mm - 2 pairs of screw-in lashing rings included - Checker plate covering over the gooseneck - 1 pair of removable ALU sideboards approx. 400 mm high, anodized, mounted on the gooseneck - Removable rear ALU wall on the gooseneck, approx. 400 mm high, anodized - 3.5" king pin / 2" king pin fitted - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - 4 wheel chocks - 4 axle load gauges - Mechanical fixed support legs at the front - 1 one-piece INOX toolbox, approx. 2,480 x 340 x 390 mm - Mechanical fixed support legs at the front - Continuous steel sheet flooring with painted-in sand layer on the platform for anti-slip protection - 1 intermediate table, approx. 500 mm wide, for the extending section, with elongated holes for suspended and adjustable bridging elements - Painted sand coating on the supporting surfaces of the intermediate table - Mechanical locking for securing the intermediate table in the extended position - 8 pairs of stake pockets in the outer frame - Extendable (galvanized) widening units approx. 230 mm per side - 1 pair of hydraulic rear supports Dwedpfx Aijk Af Svowsb - Central lubrication system - 1 reversing light each left and right at the rear of the vehicle - 3 kW electro-hydraulic power unit - Widening boards, loose, in reinforced steel U-frame - Radio and cable remote control - 4 warning panels, approx. 423 x 423 mm

Durum: yeni, boş ağırlık: 17.250 kg, azami yük ağırlığı: 48.700 kg, toplam ağırlık: 66.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 7.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 375 mm, lastik boyutu: 245/70 R 17.5, renk: gri, işletme ağırlığı: 17.250 kg, Donanım: ABS, Gooseneck: - Gooseneck in SNT design for optimized load platform length, approximately 3,750 mm long - Gooseneck hydraulically liftable/lowerable and detachable - Suitable for tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: - Low bed with external beams, configured as a telescopic vessel bridge in low construction with extension at the front - Length x width approx. 7,550 mm x 2,740 mm - Mechanical locking of the extension Chassis: - Rear chassis with closed outer frame - Tread plate covering and continuous prismatic excavator recess approx. 1,450/900 x 505 mm, open at the rear Axles, Suspension, and Tyres: - “PENDEL-AXLE”, all axles hydromechanically forced steered - Hose rupture valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins for securing in raised position - Final coating of axles with 2 layers of single-colour 2-component paint in "FAY-Grey-34-0260" - Technical axle load 12,000 kg - Hydraulic axle compensation - 245/70 R 17.5 tyres Accessories: - Detachable steel front wall, approx. 400 mm high - 4 wheel chocks - Gooseneck closed at the rear upper section with a removable cover - 1 pair of steel ramps with climbing strips and fixing bolts for bridging the low bed uptake hooks - Ramps can be placed over or between the hooks - Mounting points for steel loading ramps at the rear between the external beams of the gooseneck - One locking position approximately every 1,000 mm on the extension - 1 lashing ring each left and right on the front cross member - Supply line connection strip to the tractor unit, fitted at the height of the outer frame profile Djdpfx Aeh Hm Tzjiwjwb - 6 pairs of threaded blocks on the outside of the inner beams of the load platform for mounting screw-on M24 rings - 6 pairs of recessed lashing rings on the outside of the outer beams of the load platform, foldable inwards and outwards - 1 pair of threaded blocks at the front and rear of the outer beams of the load platform for mounting screw-on M24 rings - Insertion strip for loose ALU approach ramps on the rear cross member of the vehicle - Central lubrication system with 2 pumps, brand BEKAMAX - Remote steering from front and rear, operable via cable remote control, with single-track control of axles - 3 kW electro-hydraulic power pack for operating hydraulic functions, except hydraulic winches - Removable load floor (galvanised), can be inserted in 3 elements between the outer beams, with hardwood covering - Folding extensions, approx. 230 mm per side - Loose widening boards, framed in steel - 4 warning panels approx. 423 x 423 mm - Radio remote control for remote steering operation - 3.5" kingpin - Anti-slip stickers on the left bevel of the gooseneck - Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings - Guiding plate from gooseneck for the fifth wheel plate, approx. 800 mm wide - 1 spare wheel with mounting adapter - Parking position on the gooseneck for warning panels when not in use - 2 pairs of stanchion pockets recessed in the outer frame of the chassis for insertable stanchions approx. 100 x 50 mm - Rear section of the chassis with a detachable plate closing the bucket arm recess at the rear - Trailer colour MB 7350 Novagrau

Durum: yeni, azami yük ağırlığı: 50.400 kg, toplam ağırlık: 65.000 kg, dingil konfigürasyonu: > 3 aks, Donanım: ABS, Web sitemizde, anında ve kısa sürede temin edilebilen tüm araçlarımızı bulabilirsiniz. Donanım özetini aşağıda bulabilirsiniz. Tam donanım talebiniz üzerine sunulacaktır. KUĞU BOYNU Yükleme alanının uzunluğunu optimize etmek için SNT tasarımında kuğu boynu, uzunluk yaklaşık 3.700 mm, arka kısımda yaklaşık 1.000 mm x 10°'lik bir eğim. SZM için: 4 x 2, 6 x 2 ve 6 x 4. - Çelikten yapılmış, takılabilir ön duvar, yaklaşık 400 mm yüksekliğinde - Hidrolik işlemleri kontrol etmek için 3 kW Elektrik-Hidrolik Ünite (hidrolik vinçler hariç). - Kuğu boynunda, yanlara takılabilen 1 çift ALU yan panel, yaklaşık 400 mm yüksekliğinde, eloksal kaplama. - Kuğu boynunda, takılabilir ALU arka panel, yaklaşık 400 mm yüksekliğinde, eloksal kaplama. - 2 inç King Pin - Kuğu boynunun arka bölümünde, ALU rampa destekleri için yuva. - Ön bağlantı şeridinde yuvarlak NATO prizi (Maeler & Kaege VG 96 917) YÜKLEME ALANI Çekilebilir tasarıma sahip yükleme alanı, uzunluk yaklaşık 8.800 mm, arka kısımda yaklaşık 500 mm x 10°'lik bir eğim. Yükleme alanına ve eğime doğru uzanan bir oyuk, ekskavatör kovası kolunu tutmak için yaklaşık 3.850 x 750 x 210/290 mm (U x G x Y). Konik kilitleme pimi ve güçlendirilmiş kilitleme konumları ile pnömatik kilitleme, besleme hatları çekilebilir desteklerde korunarak bulunur ve otomatik olarak ilgili yükleme alanı uzunluğuna uyum sağlar. - ECE R 141'e uygun TPMS lastik basıncı kontrol sistemi. - BPW akslar ve süspansiyon, 1. aks ön tarafta döner mafsallı, diğer tüm akslar hidro-mekanik olarak zorunlu olarak döner. - 1. aks, geri vites üzerinden elektromanyetik geri sürüş kilidine sahiptir ve manuel olarak etkinleştirilebilir. - Teknik aks yükü: her biri 12.000 kg - Kaldırma ve indirme vanalı hava süspansiyonu. - Lastikler 245/70 R 17.5 3PMSF çift lastik. Markası bizim tercihimize bağlıdır. - Yükleme alanının kilitlemesi, yaklaşık 250 mm'de bir şekilde konik olarak kaynaklanmış sabitleme profilleri ile. - Geniş kesitli çekme borusu için yaklaşık 300 mm genişliğinde 1 ara tabla. - Genişletmeler (galvanizli), her iki tarafta yaklaşık 230 mm çekilebilir (ahşap plakalar olmadan). - Aksların önünde yaklaşık 15 x 15 mm boyutlarında kare basamaklı oluklu tekerlek yuvaları, kuğu boynunun enine traversine kadar sürekli olarak açıktır, yaklaşık 700 x 410 mm (G x D). - 1. ve 2. aks arasında, yaklaşık 15 x 15 mm boyutlarında kare basamaklı oluklu tekerlek yuvaları, yaklaşık 1.480 x 700 x 410 mm (U x G x D). - Hidrolik rampalar için kontrol vanaları, aracın sağ tarafında. - Ön ve arka taraftan kablo uzaktan kumandası ile kontrol edilebilen, aksların tek şerit kontrolü ile, SZM'ye kurulum olmadan. HİDROLİK YÜKLEME RAMPLARI DR-15/60-900-4350-KG-HV-M Yaklaşık 4.350 mm uzunluğunda ve yaklaşık 900 mm genişliğinde iki parçalı çelik rampalardan oluşan bir çift. Büyük rampa parçasının yüzeyi ikiye bölünmüştür: Dış kısımda yaklaşık 15 x 30 mm boyutlarında kare basamaklı oluklu çelik sac ve iç kısımda kauçuk yüzey. Hidrolik olarak açılabilen rampa uçları, rampalar ayrı ayrı hidrolik olarak dışa doğru yaklaşık 235 mm ve içe doğru yaklaşık 215 mm hareket ettirilebilir. Maksimum yük ve tırmanma açısı teknik veri sayfasına uygundur: C465501 - Ek güçlendirme olarak yükleme alanının eğiminde, yaklaşık 25 mm kalınlığında Super Grip kauçuk zemin ve yaklaşık 5 mm kalınlığında çelik zemin. FREN SİSTEMİ AB düzenlemelerine uygun WABCO EBS-E marka fren sistemi. Dodpfxetx Nwno Aiwewb Çekiciye bağlantı kablosu olmadan. AYDINLATMA SİSTEMİ AB düzenlemelerine uygun, ASPÖCK-NORDIK full LED tasar

Durum: yeni, azami yük ağırlığı: 38.140 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Partial equipment list. Full specifications available on request. Gooseneck: - Gooseneck with approx. 45° chamfered front corners and a rear bevel of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - Between the 1st and 2nd axle, one pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable, galvanized wheel recess covers (approx. 670 mm wide - max. point load 5 t each) - 1 pair of recessed lashing rings at the front of the loading deck (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: Tyres 235/75 R17.5 3PMSF, brand at our discretion - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to the truck via the standardised EBS interface per ISO 11992 - For correct display, the truck must be capable of transmitting and displaying this data. Axles: - BPW axles and suspension, 2 fixed axles, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve. Axle tools Dwjdow Tpq Depfx Aiwjb Brake system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Electrical system: - Electrical system in accordance with EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel structure: Steel frame made of high-strength fine-grain steels. - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel structure is automatically blasted after welding using a turbine blasting system - Second blasting with corundum for optimal coating adhesion - HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure top corrosion protection - Final painting with two coats of 2K paint, solid colour in RAL 3002 Carmine Red, rear section metallised and painted in RAL 9010 Pure White - No metallic paint possible - Paint finish tested in salt spray test per ISO 9227-NSS - Sealing of cavities with special wax Including the following accessories: - Mounts for warning signs on both sides at the gooseneck and at the rear, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch kingpin - Galvanized steel front bulkhead, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection panel - Galvanized folding supports under the loading area bevel - Hardwood impact protection on the rear wall from gooseneck to loading platform - 1 pair of recessed lashing rings along the central frame at the rear on the bevel (LC 10,000 daN) - Aluminium side walls and tailboard on the gooseneck