Kullanılmış Faymonville Standart Yapı satın al (225)

Durumu: yeni, azami yük ağırlığı: 30.190 kg, toplam ağırlık: 43.000 kg, dingil konfigürasyonu: 2 dingil, Donanım: ABS, You can find our complete range of vehicles, including immediately and shortly available units, on our website. Excerpt from the equipment list. Full specification available upon request. Loading platform: * Lowbed with external beams, extendable version SUPER LOW design, length approx. 6,850 mm * Lowbed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking * Supply lines are protected within the extendable beams and automatically adapt to the lowbed length * 5 pairs of lashing rings, foldable to the outside (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting RUD screw-on rings Gooseneck: * Gooseneck in SNT design to optimize load area length, length approx. 3,750 mm * Gooseneck hydraulically lift/lowerable and detachable * Technical fifth-wheel load: 23,000 kg * Suitable for tractors: 4 x 2, 6 x 2 Rear undercarriage: * Rear axle assembly, short version, with closed outer frame and checker plate cover * Undercarriage with excavator trough, rear half closed to accommodate air tanks * 2 pairs of lashing rings, foldable to the outside (LC 5,000 daN) * 1 pair of lashing rings, foldable to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front & rear of the undercarriage (LC 10,000 daN) Axles: * BPW axles, hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres: * Tyres 245/70 R 17.5 3PMSF * Brand of our choice * Load index (146/146F) * TPMS tyre pressure monitoring system in accordance with ECE R 141 * Data transmission to the truck via standardized EBS interface according to ISO 11992 * The truck must be able to receive and display this data correctly Brake system: * Brake system compliant with EU regulations, with EBS-E (2S2M) Lsdpfx Agsxarl Neljai Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel structure: * Steel structure made from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: * Entire steel structure automatically shot-blasted with turbine system after welding * Second blasting treatment with corundum for optimal coating adhesion * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminium) for maximum corrosion protection * Final painting: 2 coats 2K topcoat, RAL 3002 carmine red, in accordance with RAL system 841GL * Rims in silver * Rear section metallized and painted RAL 9010 pure white * Metallic paint not possible * Paint system tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including the following additional equipment: * 2" kingpin * One galvanized steel front wall, approx. 400 mm high * Remote steering at front and rear via wired remote control with push-buttons, with single-track axle control (no installation in tractor unit) * Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Preparation for mounting screw-fitted container locks for 1x 20' or 1x 40' container on t

Durumu: yeni, azami yük ağırlığı: 36.461 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.480 mm, toplam yükseklik: 860 mm, Üretim yılı: 2025, Technical Description Gooseneck: Gooseneck with rear taper approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Area: Hydraulically liftable and lowerable platform after the gooseneck, approx. 2,800 mm in length, with rear taper approx. 1,000 mm x 8°. 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN). 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN). 1 pair of foldable lashing rings to the inside on the front central beam (LC 10,000 daN). Grating floor covering C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles tread plate covering. Two-Piece Steel Ramps: One pair of galvanized two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating covering C40/5 (point load 8 t on an area of 20 x 20 cm). Ramps with hydraulically folding ramp sections and hydraulic lifting mechanism. Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not included in the overall vehicle length of 16,500 mm. Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R17.5 3PMSF tyres at the manufacturer’s discretion. TPMS: TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface according to ISO 11992. For proper display, the towing vehicle must be capable of transmitting and displaying this data. Axles: BPW axles and suspension, 2 rigid axles, 1 trailing steering axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated by reverse gear and manually. Air suspension with lift and lower valve. Axle tools. Lsdpfx Aew Dl Hwjgljai Brake System: WABCO brake system in accordance with EU regulations with EBS-E (2S2M) without connection lines to the tractor unit. Electrical System: Electrical system complying with EU regulations, 24-volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicators. ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Manufactured from high-strength fine-grained steels. Steel grades: – S355J2+N / S355MC (yield strength 355 MPa) – S690QL / S700MC (yield strength 690 MPa) Curtain Body: Curtain body ??? 3,960 mm ??? – Galvanized front wall with tensioning system for sliding curtains. – "EDSCHA" brand roof, forward-sliding on ALU roof bow profiles (bolted to front and rear wall). – 3 pairs of sliding stakes in the loading area. – Rear of the body hydraulically extendable to left and right by approx. 750 mm. – Sliding roof with upwards foldable portal beam. – Sliding curtain with 700 mm length reserve, lashing straps approx. every 600 mm. – Height to upper edge of body approx. 3,960 mm (loaded). – Driving with open sliding roof is prohibited and will damage the curtain. Paintwork: Entire steel structure is automatically blast-cleaned with a wheel blasting machine after welding. Second blast treatment with corundum for optimal coating adhesion. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection. Final painting with 2 coats of 2K topcoat, single colour, shade of choice according to RAL system 841GL. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint.

Durumu: kullanılmış, azami yük ağırlığı: 62.400 kg, toplam ağırlık: 85.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 11/1997, with hydraulic suspension, hydromechanical forced steering, double telescopic loading platform, with rear chamfer Neck (Gooseneck) hydraulically adjustable - Designed loading platform 3,700 x 2,480 mm - Hydromechanical forced steering (dual-circuit steering) - Slewing ring-mounted fifth wheel plate with replaceable 3.5" kingpin and adjustable steering wedge - Maximum steering radius (internal) 2,700 mm - Fifth wheel load 25,000 kg Loading platform - Double telescopic, constructed as outer and inner tube design with 1,000 mm fixed loading platform section at the front - 500 mm long intermediate deck Chassis - ABS - Hydraulically suspended 6-axle chassis - SAF axle units, consisting of 5 forced-steerable steering axles and 1 fixed axle - Axles with adjustable tapered roller bearings and automatic slack adjusters (AGS) Vehicle rear - Design "chamfered", 500 mm - Mechanical rear support Special equipment - Electro-hydraulic power pack - Radio remote control - Lift option (load-dependent) for axles 1 and 2 Ramps, 2-section hydraulic 2,900 mm + 1,700 mm, 850 mm wide Dimension L: 16,400 mm - 32,900 mm Unladen weight: 22,600 kg Technical Data Neck (Gooseneck) Lsdowy A T Hspfx Aglsai Loading area (LxW): 3,700 x 2,480 mm Loaded fifth wheel height: 1,300 mm Steering radius: 2,700 mm Fifth wheel load: 25,000 kg Loading platform Loading area (LxW): 13,000 mm x 2,750 mm Double telescopic, 8,000 mm + 8,500 mm, for a total of 29,500 mm deck length Travel height: 900 mm (+/-130 mm) Steering 1st axle, self-steering 2nd – 6th axle, hydromechanical forced steering (dual-circuit steering)

Durumu: yeni, azami yük ağırlığı: 39.670 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, Donanım: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Summary of equipment. Full equipment details available upon request. Gooseneck: * Gooseneck with approx. 30 mm thick hardwood flooring * Gooseneck at the rear, straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading Area: * Extendable loading area * 5 pairs of fold-out lashing rings on the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings on the outside (LC 10,000 daN) * 1 pair of lying lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension belts (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, diamond plate over the axles Landing Legs: JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, two fixed and two self-steering axles * Air suspension with lifting/lowering function * Self-steering axles with electromagnetic reversing lock, can be activated via reverse gear or manually * Drum brakes * Axle tools Tyres: * 205/65 R 17.5 * Brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141 * Data transmission to the tractor via standardised EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to transmit and display this data Brake System: * Brake system in compliance with EU regulations with EBS-E (4S3M), without connector lines to the tractor unit Steel Construction: * Steel structure made from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: * Entire steel structure automatically shot-blasted after welding * Secondary blast treatment with corundum for optimal coating adhesion * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection * Final paint finish with 2 coats of 2K topcoat, single colour in RAL 3002 carmine red, according to RAL 841GL * Rims in silver * Rear section metallised and painted in RAL 9010 (pure white) * Metallic paints not possible * Paint system tested in salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Electrical System: Lasdpfxjxarlvo Aglei * Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights flash with the indicators * ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets; connections according to ISO (24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098) Accessories included: * 2-inch king pin * One spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanised front connection rail * Galvanised drop supports under the ramped section of the loading area * One galvanised steel bulkhead (EN12642-XL), approx. 1,600 mm high * Removable ALU side boards and rear gate approx. 2,440 x 400 mm (L x H) on the gooseneck * Rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) * Support block with 1 pair of WADER container pockets; fifth wheel load approx. 20,000 kg * 7 pairs of WADER container pockets for 1x 20' container in the loading area * 1x 40' container in the loading area, 1x 40' container above the gooseneck, 2x 20' container * 7 pairs of stanchion pockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading area * One galvanised crosswise holder under...

Durumu: yeni, azami yük ağırlığı: 40.017 kg, toplam ağırlık: 50.960 kg, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Technical Description Gooseneck: Gooseneck with rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Loading Area: 5 pairs of fold-out lashing rings (LC 5,000 daN). 3 pairs of fold-out lashing rings (LC 10,000 daN). 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN). Hardwood flooring approx. 48 mm thick, tread-plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 205/65 R17.5, manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit is via the standardised EBS interface as per ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles: two fixed axles, two self-steering axles, air suspension, drum brakes, lifting/lowering function. The self-steering axles have electro-magnetic reverse lock, activated via reverse gear or manually. Axle tool included. Brake System: WABCO brake system compliant with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit. Electrical System: Electrical system as per EU regulations, 24 Volt LED lighting ASPÖCK-NORDIK (ASS3). All LED side marker lights synchronise with the indicator. ASPÖCK-UNIBOX on the front connection rail with 24N, 24S & 15-pin sockets. Connections in accordance with ISOs: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: Entire steel structure automatically shot blasted after welding using a shot blasting system. Second blasting treatment with corundum for optimum adhesion of the coating system. HRM metallisation of the complete chassis with ZINACOR 850 (85% zinc/15% aluminium) for optimal corrosion protection. Final painting: two coats of 2-pack topcoat, single-colour in a shade of choice according to the RAL 841GL system. Lsdpfsw Dl Hqjx Agljai Rear section metallised and painted in RAL 9010 (pure white). Metallic finishes not available. Paint specification tested according to salt spray test ISO 9227-NSS. Cavity sealing with special wax. Options Included: 2'' kingpin One galvanised steel front wall. Yellow-red air couplings fitted to the galvanised front connection rail. 2 wheel chocks with holders on the front wall. Mountings at the rear of the gooseneck for ALU ramps. Further options available.

Durumu: kullanılmış, azami yük ağırlığı: 34.420 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2014, Gooseneck length approx.: 3,500 mm. Steering radius: 2,300 mm for 3-axle tractor unit. 18,000 kg fifth wheel load. Coupling height when loaded approx.: 1,140 - 1,350 mm. Height compensation swingarm at front approx.: -280 / +250 mm. Loading platform length approx.: 9,500 mm. Loading width approx.: 1,560 mm. Rear suspension hydraulic. BPW axles with ABS. Independent wheel suspension, hydraulic axle equalization with lifting and lowering device. Each axle can be lifted individually. Central lubrication system with 1 pump, BEKAMAX. Foldable aluminum side boards on the gooseneck, approx. 400 mm high, anodized version. 24 volt power unit. Ljdpfx Aewi Ei Asgloai

Durumu: yeni, azami yük ağırlığı: 40.790 kg, toplam ağırlık: 59.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.750 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately or soon, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: - Gooseneck in SNT design for optimizing loading deck length, approx. 3,700 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6 x 4 or 8 x 4 Low-bed Deck: - Low-bed with external frame beams, extendable design, SUPER LOW construction, approx. 7,550 mm length - Low-bed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking - Supply lines routed and protected inside the extendable beams, automatically adjusting to the current deck length - 7 pairs of lashing rings foldable outward (approx. LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for installing boltable RUD lashing rings Rear Running Gear: - Rear running gear with closed outer frame, tread plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of lashing rings foldable outward (approx. LC 10,000 daN) - 1 pair of lashing rings embedded in the recess (approx. LC 10,000 daN) - 2 pairs of lashing rings embedded in the recess (approx. LC 16,000 daN) - 2 pairs of stake pockets for insertable stanchions, approx. 100 x 50 mm, in the outer frame PENDLE-AXLE: - PENDLE-AXLE, all axles hydraulically/mechanically forced-steered - Hose rupture valve on axle leveling cylinder with automatic reset function - Hydraulic cylinders with shut-off cocks and transport locks to secure in raised position - Axles finished with 2 coats of 2K paint, solid color, painted in grey 34-0260 - Technical axle load: 12,000 kg per axle - Hydraulic axle leveling - Axle tooling Tyres: - Tyres 245/70 R 17.5 3PMSF – brand of our choice. Load index (146/146F) Braking System: - Braking system compliant with EU regulations with EBS-E (2S2M), no connection lines to the tractor unit Electrical System: - Electrical system according to EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel Construction: - Steel construction made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: - Complete steel structure automatically shot-blasted with blast wheel system after welding - Second blasting with corundum for optimal coating adhesion - Final painting with 2 coats of 2K topcoat paint, solid color in RAL 3002 Carmine Red according to RAL System 841GL - Rear section metallized and painted in RAL 9010 (pure white) - Rims in silver grey - No metallic paint possible - Paintwork tested in salt spray test according to ISO 9227-NSS - Cavities sealed with special wax Accessories Included: - Prepared for bolt-on container locks for 1x 20' or 1x 40' container on the outer beams - Without container locks - 3.5-inch kingpin - One galvanized steel front wall, approx. 400 mm high - One spare wheel mount in front of the bulkhead Lasdpfjw Tprbsx Aglei - Yellow-red air couplings on the galvanized front connector strip - Axle steering from front and rear via cable remote control (push-button operation), with single-track monitoring of axles (no installation in tractor unit) - Electro-hydraulic powerpack - On the gooseneck: plug-in aluminium side and rear walls, approx. 2,000 x 400 mm

Durumu: yeni, azami yük ağırlığı: 38.953 kg, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Gross vehicle weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading platform length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Steering angle radius (rear): 2,300 mm Loading height at max. load: 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical Description Gooseneck: Gooseneck with chamfered front corners at 45° and rear taper of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Lasdpfx Aog Sk Tregloi Loading platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8°. 6 pairs of folding lashing rings facing outward (LC 5,000 daN). 2 pairs of folding lashing rings facing outward (LC 10,000 daN). 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN). Cut-outs in the outer frame of the loading platform for attaching tensioning straps. (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, above the axles fitted with chequer-plate covering. Ramps: Two-piece steel ramps: One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering. Ramps with hydraulically foldable ramp sections, hydraulic lifting device and can be hydraulically adjusted laterally. Maximum load per pair: 40,000 kg Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 235/75 R 17.5 tyres as per manufacturer's selection. Axles: SAF axles, air-suspended, with drum brakes, featuring lift/lower function. Last axle is force-steered with electro-magnetic reverse lock, activatable via reverse gear or manually. Axle tools. Brake System: Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit. Steel Construction: Steel construction made from high-strength fine-grained steel. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: Premium and durable corrosion protection via sandblasted welded frame, primed with 2-component (2K) zinc dust primer. High-quality single-tone 2-component (2K) top coat in RAL colours of your choice. Rear metalized and painted in RAL 9010 (pure white). Metallic paint not possible. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets. ISO-compliant connections. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories Included 2" king pin One galvanized steel front bulkhead approx. 400 mm high. At the galvanized front connection strip yellow/red airline couplings. 4 wheel chocks with holder on the front bulkhead (± 5kg). Cable for supplying electro-hydraulic unit and/or electric winch (35 mm², 3.5 m long, max. 250A) between semi-trailer and tractor unit, with plug connection (ANDERSON-ANDERSON). Galvanized folding supports under the rear slope of the loading platform. Bracket for a rotary beacon at the rear of the trailer. Control valves for the ramps installed on right-hand side of trailer (± 4kg). Yellow reflective tape according to EU regulations on the sides and rear of the trailer. Electro-hydraulic unit mounted at the rear under the loading

Durumu: yeni, azami yük ağırlığı: 38.400 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle stock with immediately and short-term available vehicles on our website. Excerpt of the equipment. Complete equipment list available upon request. Loading platform: * Extendable loading platform with pneumatically operated locking mechanism * Loading platform with approx. 30 mm thick wooden planks * 7 pairs of folding lashing rings to the outside (LC 5,000 daN) * 3 pairs of folding lashing rings to the outside (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres 385/65 R 22.5, brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the tractor unit takes place via the standardized EBS interface according to ISO 11992. The tractor unit must be capable of receiving and displaying this data for accurate monitoring. Axle: * BPW axles and suspension * All axles hydro-mechanically forced-steered * Disc brakes * Technical axle load: 10,000 kg each (ET 0) * Air suspension with lifting and lowering valve * Axle tools Brake system: * WABCO braking system according to EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations * 24 Volt LED lighting ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection rail with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting: * Complete steel construction automatically blast-cleaned by shot blasting machine after welding * Second blasting with corundum for optimal coating adhesion * Final coating with 2 layers of 2K top coat, single-colour in RAL 3002 Carmine Red according to RAL System 841GL * Rims in silver grey * Rear section metallized and painted in RAL 9010 (Pure White) * Metallic paint not possible * Coating structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Accessories: * Remote steering from the front and rear via cable remote control with push buttons, with axle tracking control (installation in the tractor unit not included) * Electro-hydraulic unit * 4 wheel chocks with holders at the front wall * 2 inch king pin * At the galvanized connection rail in front, yellow-red air couplings * Mountings for warning boards left and right on neck and rear, including socket * 10 pairs of stanchion pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container locks in the loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking point provided in the extension for a 45' container * 4 pairs of transverse stanchion pockets mounted across the platform for plug-in stakes approx. 100 x 50 mm Ledpow Tpr Ijfx Agloai * Storage for up to 9 pairs of plug-in stakes bolted to the front wall on the inside * Climbing ladder mounted left and right in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted at the front under the loading platform on the l

Durumu: yeni, toplam ağırlık: 58.000 kg, Üretim yılı: 2025, Low-bed semi-trailer MAX100 4 A 8.60 U Technical Data Lodpog Sk T Dofx Aglsai Speed: 80 km/h Gross Vehicle Weight: 60,800 kg Fifth Wheel Load: 18,000 kg Axle Load: 42,800 kg Tare Weight: Payload: Gooseneck Length: 3,850 mm Loaded Fifth Wheel Height: 1,250 mm Loading Platform Length: 8,600 mm Extendable by: 5,400 mm Axle Spacing: 1,360 mm Steering Radius (rear): 2,300 mm Loading Height at Max. Load: 860 mm Overall Width: 2,540 mm Suspension Stroke: -55/+145 mm Technical Description Gooseneck With 45° chamfered front corners and rear chamfer approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) 30 mm thick hardwood floor Extendable loading platform With rear bevel approx. 1,000 mm x 8° 5 pairs of outward-folding lashing rings (LC 5,000 daN) 3 pairs of outward-folding lashing rings (LC 10,000 daN) 1 pair of flush-mounted lashing rings at the front of the loading platform (LC 10,000) Approx. 48 mm thick hardwood flooring, chequer plate above the axles Ramps Two-part steel ramps One pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 mm x 800 mm with approx. 48 mm hardwood flooring Ramp sections hydraulically lifted and folded in, hydraulic lift and hydraulically adjustable position Max. load per pair: 40,000 kg Tyres 235/75 R 17.5 Brake System compliant with EU regulations, with EBS-E (4S3M) Without connection lines to the tractor unit Paintwork First-class, long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by 2-component zinc dust primer High-quality 2-component (2K) top coat, single colour, in RAL shades of choice Rear section metallized and painted in RAL 9010 (Pure White) Landing Legs: JOST mechanical landing legs with 2-speed gearbox for 24t Lifting capacity (50t test load) Steel construction made from high-strength fine-grained steels. Steel Qualities: Steel construction made from high-strength fine-grained steel S355J2+N/S355MC (Yield Strength 355MPa) S690QL/S700MC (Yield Strength 690MPa) Electrical System according to EU regulations, lighting: LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets Connection as per ISO. 24N IS0-1185 24S IS0-3731 15-pin IS0-12098 Accessories included: One galvanized steel headboard approx. 400 mm high 2" king pin 4 wheel chocks with holders on the headboard One holder for revolving beacon at rear of trailer SAF axles, two rigid axles, one self-steering axle, air suspension, with drum brakes, with raise/lower function The self-steering axle with electromagnetic reverse lock, can be activated by reverse gear or manually Axle tools included Support for ALU approach ramps at the rear of the gooseneck Galvanized folding supports under the loading platform chamfer Mechanical safety lock for the loading platform extension One spare wheel with holder in front of the headboard Yellow reflective tape as per EU regulations on sides, extension, and rear of trailer At the front galvanized connector strip, yellow-red air couplings On gooseneck and rear apron left and right, mounts for warning plates, including sockets A mudflap at the rear of the trailer Manual and description On the gooseneck: Plug-in aluminium sideboards and rear wall, approx. 2,440 x 400 mm (LxH) Rear galvanized stanchions are removable Body length approx. 2,560 mm, +/- 46 kg 3 pairs of WADER container locks in the loading platform for a 20', 30', or 40' container (±30 kg) 6 pairs of pockets for plug-in stanchions

Durumu: yeni, azami yük ağırlığı: 33.865 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, Donanım: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck * Gooseneck with chamfered front corners approx. 45° and rear chamfer approx. 750 mm x 10° Ledpsw Tprzofx Aglsai * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load Platform * Double extendable version with rear chamfer approx. 500 mm x 8° * 6 pairs of outward folding lashing rings (LC 5,000 daN) * 4 pairs of outward folding lashing rings (LC 10,000 daN) * 1 pair of recess-mounted lashing rings at the front of the loading area (LC 10,000 daN) * 1 cross table approx. 250 mm * Hardwood flooring approx. 48 mm thick, with checker plate coverage over the axles * Cutouts in the outer frame of the loading area for inserting tensioning straps (LC 2,000 daN) Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lift and lower valve * Axle tool kit Tyres: * Tyres 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Brake System: * Brake system compliant with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Paintwork: High-quality, durable corrosion protection * High-quality 2-component (2K) topcoat painted in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Steel Construction: Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical System: * Electrical system according to EU regulations * Lighting 24 volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front wiring panel * Spare wheel carrier in front of the front wall * Electro-hydraulic power unit * Remote steering from the front and rear via cable remote control with push buttons, with single-track axle alignment (without installation in the tractor unit) * Rear gooseneck mounting point for aluminum loading ramps * Rear hanging rail for aluminum loading ramps * Galvanized folding supports under the rear chamfer of the load platform * On the gooseneck: removable aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * Removable galvanized rear stanchions (body length approx. 2,560 mm) * Tool box, galvanized, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the load area for 1x 20', 2x 20', 40', or 45' containers * 8 pairs of stanchion pockets for plug-in stanchions approx. 100 x 50 mm in the outer frame of the cargo area * Galvanized wideners, extendable by approx. 230 mm per side * Movable hanging rails for aluminum loading ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps using NLGI-2 standard grease and removable protection around the pump * 2 LED reversing lamps mounted on the rear panel * HRM Metallization (High Resistance Metallisation). Complete steel structure sh

Durumu: yeni, dingil konfigürasyonu: 3 aks, Üretim yılı: 2025, Further information here: Lodpfsv D Abmsx Agljai

Durumu: yeni, azami yük ağırlığı: 37.710 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our entire stock of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: - Gooseneck with front beveled corners approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring approx. 30 mm thick Loading platform: - Telescopic loading platform with rear bevel approx. 1,000 mm x 8° - Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable and galvanized covers over the wheel recesses (width = approx. 670 mm; max. point load 5 t/unit) - 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) - 4 pairs of outward-folding lashing rings (LC 5,000 daN) - 3 pairs of outward-folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg each - Electro-magnetic reverse lock, activated via reverse gear and manually - Air suspension with lifting and lowering valve. Axle tools Tyres: - Tyres 235/75 R 17.5 3PMSF – brand of our choice Landing legs: - JOST mechanical landing legs with 2-speed gearbox, lift capacity approx. 24 t (test load approx. 50 t) Braking system: - Wabco braking system as per EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel construction: - Steel structure made from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system per EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paint finish: - Premium and durable corrosion protection for the standard shot-blasted welded frame ensured by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) topcoat single-color in RAL 3002 carmine red - Rear section metallized and painted in RAL 9010 (pure white) Included accessories: - 2” kingpin - One galvanized steel front wall, approx. 400 mm high - Spare wheel bracket in front of the front wall - Yellow-red air couplings at the galvanized connection bar at the front - 4 wheel chocks with holder at the front wall Lsdsw Tpq Rjpfx Agleai - Mounting at the rear of the gooseneck for aluminum drive-on ramps - Galvanized folding supports under the rear bevel of the loading platform - Bracket for a beacon at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - Yellow reflective tape to EU regulations at the sides, on the extension, and rear of the trailer - On the gooseneck and rear panel left and right, each with a holder for warning boards including socket - 1 hardwood buffer on the rear wall from gooseneck to loading platform - One galvanized holder for extension timbers on left and right under the loading platform - 4 pairs of recessed lashing rings along the central beam (LC 5,000 daN) - 1 pair of recessed lashing rings along the rear central beam (LC 10,000 daN) - On the gooseneck, plug-in aluminum side and rear walls, approx. 2,440 x 400 mm (L x H) - The rear galvanized stakes are removable (length of superstructure approx. 2,560 mm) - A tool box ...

Durumu: yeni, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2025, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Gross weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Loaded saddle height: 1,200 mm Rear steering radius: 2,300 mm Loading platform length: 6,850 mm Extendable by: 5,500 mm Loading height at maximum load: 350 mm Chassis length: 2,600 mm Rear chassis loading height at max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Overall width: 2,540 mm Gross weight depends on fifth wheel load. Lowbed: Lowbed with external beams, extendable version "SUPER LOW" design, length approx. 6,850 mm. Lowbed with fixed hardwood floor approximately 40 mm thick and mechanical locking device. Supply lines are protected inside the extendable beams and automatically adjust to the respective lowbed length. 5 pairs of lashing rings, foldable outward (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear chassis: Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at rear. 2 pairs of lashing rings, foldable outward (LC 10,000 daN). 1 pair of lashing rings, flat in the trough (LC 8,000 daN + 5,300 daN). 2 pairs of pocket sockets for stanchions 100 x 50 mm in the external frame. Gooseneck: Gooseneck in SNT design to optimize usable platform length, length approx. 3,785 mm. Gooseneck hydraulically lift/lowerable and detachable. Technical fifth wheel load: 23,000 kg For tractor units: 4x2, 6x2, and 6x4 PENDLE-AXLE: “PENDLE-AXLE”, all axles hydro-mechanically forced steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and plug pins for securing in raised position. Axles finished with two coats of 2-component paint, single color "FAY-Grey-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tools. Brake system: Brake system in accordance with EU regulations, with EBS-E (2S2M) without connecting lines to the tractor unit. Electrical system: Electrical system according to EU regulations, 24V lighting ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection strip with 24N, 24S, and 15-pin sockets. Connection according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel construction: Steel construction made of high tensile fine-grained steels. Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Ledpjizu Nwofx Agloai Painting: Premium, long-lasting corrosion protection of the standard shot-blasted welded frame, ensured by a two-component (2K) zinc dust primer. Premium two-component (2K) topcoat in one RAL color of your choice. Rear section metallized and painted in RAL 9010 (Pure White). No metallic paint possible. Tyres: Tyres 245/70 R 17.5 3PMSF Manufacturer’s choice. Load index (146/146F). Prepared for fitting of bolt-on container positions for 1x 20' or 1x 40' container on the external beams. Without container locks. • 2” king pin • Galvanized steel front wall approx. 400 mm high • 1 spare wheel with holder in front of the front wall • 2 wheel chocks with holder on the front wall • Yellow-red air couplings on the galvanized connection strip at the front. Remote steering from front and rear via cable remote control with pushbuttons, with single-track axle monitoring (without installation in the tractor unit). Hydraulic connections from the gooseneck to the lowbed

Durumu: yeni, azami yük ağırlığı: 61.050 kg, toplam ağırlık: 73.000 kg, dingil konfigürasyonu: 3 aks, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Complete specification available on request. Loading Platform: * Loading platform with approx. 30 mm hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing Gear: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles and Suspension: * BPW axles, each technically rated to 12,000 kg * 1st axle self-steering, 2nd axle fixed, all other axles hydro-mechanically force-steered, mounted on turntable * Air suspension with lift/lower valve * Axle tool Tyres: * Tyres: 445/65 R 22.5 169K – manufacturer of our choice, TPMS * TPMS tyre pressure monitoring system according to ECE R 141 * Data transfer to the tractor unit via standardised EBS interface in accordance with ISO 11992 * To ensure correct display, the tractor unit must be able to transmit and display these data Braking System: * Wabco braking system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Electrical System: * Electrical installation according to EU regulations * 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights flash with the indicators * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel Construction: * Steel structure made from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Ledpfxsw Tpr Uo Agljai Paintwork: * Complete steel structure is automatically blast-cleaned after welding using a shot-blast machine * Second blasting with corundum for optimum adhesion of the coating system * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection * Final coating: 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red according to the RAL 841GL system * Rear end metallized and painted in RAL 9010 (Pure White) * Wheels painted silver grey * Paint system tested by salt spray test according to ISO 9227-NSS * Cavities sealed with special wax * No metallic paint possible Including the following accessories: * Loading area with approx. 30 mm hardwood floor * 2-inch kingpin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connector strip * Supports for approx. 1,000 mm plug-in stakes in the rear center beam * Swanneck and rear apron both left and right fitted with a holder for warning signs including socket * Remote steering from front and rear via wired remote with push buttons, single-track axle control (no installation required in tractor unit) * Electro-hydraulic unit * 13 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the bed * Lift axle on first and second axles with control via TEBS E, depending on actual axle load and loading condition * 7 pairs of galvanized plug-in stakes approx. 100 x 50 mm, approx. 1,000 mm high * 5 pairs of crosswise stake pocket rails mounted on platform for plug-in stakes approx. 100 x 50 mm * 2 pairs of WADER container pockets in the loading area for 1x10’ * 1 shunting coupling reinforced, screwed to rear crossmember * Centralized lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable pump protector * Hydraulically...

Durumu: yeni, azami yük ağırlığı: 36.156 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Gross vehicle weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Tare weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Platform length: 13,600 mm Loaded fifth wheel height: 950–1,050 mm Swing clearance at rear: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360 / 1,405 mm Overall width: 2,540 mm Technical Description Load platform: Load platform in extendable design with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of fold-out lashing rings (LC 5,000 daN). 2 pairs of fold-out lashing rings (LC 10,000 daN). Cut-outs in the outer frame of the platform for attaching tension straps (LC 2,000 daN). Landing legs: JOST mechanical landing legs with 2-speed gearbox for 24 t lifting capacity (50 t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). Trailing steering axles with electro-magnetic reversing lock, activated via reverse gear or manually. Axle tools (± 80 kg). Brake system: Brake system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Paintwork: Premium, long-lasting corrosion protection for the standard shot-blasted welded frame ensured by a two-component (2K) zinc-rich primer. High-quality two-component (2K) topcoat, single-colour, in RAL tones of your choice. Rear section metallised and painted in RAL 9010 (pure white). Metallic paint not available. Electrical system: Electrical system according to EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connector panel with sockets 24N, 24S & 15-pin. Connections according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Standard accessories included: Yellow-red air couplings on the galvanised front connector panel. 2 wheel chocks with holders. 2" kingpin. Galvanised steel front wall, approx. 2,200 mm high (± 105 kg), EN12642-XL compliant. Yellow reflector tape according to EU regulations; fitted along the sides, on the extension, and the rear of the trailer. European reflective warning plates (red-yellow) at the rear of the trailer. Platform with approx. 38 mm hardwood floor (± 320 kg). 10 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the platform (± 30 kg). 1 spare wheel holder under the platform, right-hand side in direction of travel. Tyres 435/50 R 19.5, manufacturer’s choice. Lajdpfeg Sk Tvox Aglji One mud flap at the rear of the trailer. Manual and documentation on USB stick. Bracket for rotating beacon at the rear of the trailer. At the gooseneck and rear panel, left and right, brackets for warning signs, incl. socket. One transverse INOX toolbox under the platform (1,000 x 400 x 250 mm) (± 135 kg). 6 pairs of WADER container locks in the platform for 1 x 20’ container, 2 x 20’ containers or 1 x 40’ container; an additional locking position provided in the extension for a 45’ container (± 90 kg). 4 pairs of WADER container locks (± 60 kg). 10 pairs of galvanised plug-in stakes approx. 100 x 50 mm, 1,000 mm high (± 220 kg). 3 pairs of crosswise stake pocket bars mounted in the platform for plug-in stakes 100 x 50 mm (± 95 kg). Storage for 1,000 mm plug-in stakes (± 45 kg). 1 spare wh

Durumu: yeni, azami yük ağırlığı: 36.245 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Selection of features. Full equipment details available upon request. Loading Platform: * Loading platform made of hardwood floor with rear taper approx. 1,000 mm x 8° * 2 pairs of lashing rings (LC 5,000 daN) * 1 pair of lashing rings (LC 10,000 daN) * 6 pairs of outward folding lashing rings (LC 5,000 daN) * 2 pairs of outward folding lashing rings (LC 10,000 daN) * Cut-outs in the external frame of the loading platform for securing straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air-suspended Lajdpfow Tpqqox Aglsi * Disc brakes (approx. 377 mm) * Raise/lower function (ET 120) * Axle toolkit Tyres: * Tyres 435/50 R 19.5 – brand at our discretion * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the tractor unit via the standardised EBS interface in accordance with ISO 11992. For correct display, the tractor unit must be able to transmit and display this data. Brake System: * Wabco brake system compliant with EU regulations featuring EBS-E (2S2M) without connecting lines to the tractor unit Steel Construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical System: * Electrical system according to EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin connectors in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: * Complete steel construction automatically shot-blasted with wheel-blasting machine after welding * Second round of blasting with corundum for optimum adhesion of the coating system * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc, 15% aluminium) to ensure best corrosion protection * Final coating with two coats of 2-component topcoat, single colour in RAL 3002 Carmine Red according to RAL system 841GL * Rear section metallised and painted in RAL 9010 (Pure White) * Coating system tested by salt spray test in accordance with ISO 9227-NSS * Sealing of cavities with special wax * Metallic paint finish not available Including the following additional equipment: * Yellow-red air couplings on galvanised connector strip at the front * 4 wheel chocks with brackets * 2-inch king pin * Loading platform with heavy-duty hardwood floor * 1 spare wheel holder under the loading platform on the right-hand side * Galvanised folding supports under the platform’s rear taper * 9 pairs of stake pockets for drop-in stakes, approx. 100 x 50 mm, in the external frame of the loading platform * One galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * A painted sand layer applied to the central beam for slip resistance * 1 INOX toolbox mounted transversely under the loading platform, approx. 1,000 x 400 x 2,500 mm * 6 pairs of WADER container pockets in the platform, for 1x 20' container, 2x 20' containers or 1x 40' container * 3 pairs of transverse stake pocket strips mounted in the platform, for drop-in stakes approx. 100 x 50 mm * Storage for max. 9 pairs of drop-in stakes approx. 100 x 50 mm bolted to the inside of the front wall * 2 INOX toolboxes under the loading platform left and right, a

Durumu: yeni, azami yük ağırlığı: 44.000 kg, toplam ağırlık: 61.000 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, Further information here: Lsdpfev D Abtjx Agloai

Durumu: yeni, azami yük ağırlığı: 38.140 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Partial equipment list. Full specifications available on request. Gooseneck: - Gooseneck with approx. 45° chamfered front corners and a rear bevel of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - Between the 1st and 2nd axle, one pair of fixed integrated wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable, galvanized wheel recess covers (approx. 670 mm wide - max. point load 5 t each) - 1 pair of recessed lashing rings at the front of the loading deck (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Landing legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: Tyres 235/75 R17.5 3PMSF, brand at our discretion - TPMS tyre pressure monitoring system according to ECE R 141 - Data transmission to the truck via the standardised EBS interface per ISO 11992 - For correct display, the truck must be capable of transmitting and displaying this data. Lasdpfx Agew Tpq Delsi Axles: - BPW axles and suspension, 2 fixed axles, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve. Axle tools Brake system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Electrical system: - Electrical system in accordance with EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel structure: Steel frame made of high-strength fine-grain steels. - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Entire steel structure is automatically blasted after welding using a turbine blasting system - Second blasting with corundum for optimal coating adhesion - HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure top corrosion protection - Final painting with two coats of 2K paint, solid colour in RAL 3002 Carmine Red, rear section metallised and painted in RAL 9010 Pure White - No metallic paint possible - Paint finish tested in salt spray test per ISO 9227-NSS - Sealing of cavities with special wax Including the following accessories: - Mounts for warning signs on both sides at the gooseneck and at the rear, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch kingpin - Galvanized steel front bulkhead, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection panel - Galvanized folding supports under the loading area bevel - Hardwood impact protection on the rear wall from gooseneck to loading platform - 1 pair of recessed lashing rings along the central frame at the rear on the bevel (LC 10,000 daN) - Aluminium side walls and tailboard on the gooseneck

Durumu: yeni, azami yük ağırlığı: 34.104 kg, toplam ağırlık: 47.000 kg, dingil konfigürasyonu: 2 dingil, Üretim yılı: 2025, Further information here: Lsdpfx Aov D Abgogljai

Durumu: yeni, azami yük ağırlığı: 37.820 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpts from the equipment list. Complete specifications available upon request. Gooseneck: Gooseneck with beveled front corners approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Area: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and widened lower sections * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) * Including 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t each * Recess in the bevel as well as in the loading area for accommodation of the excavator stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of flat-mounted lashing rings at the front of the loading area (LC 10,000 daN) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cutouts in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) One-piece Steel Ramps: * One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulic lifting gear, hydraulically movable * Maximum load capacity per pair: 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in driving position are not counted in the total vehicle length Landing Legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering trailing axle * Technical axle load: 12,000 kg per axle * Electromagnetic reverse lock activated by reverse gear and manually * Air suspension with raise/lower valve * Axle tools Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion * TPMS tyre pressure monitoring system according to ECE R 141. Data transmission to the truck is via the standardized EBS interface in accordance with ISO 11992. For correct display, the truck must be capable of receiving and displaying this data. Brake System: * WABCO braking system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Steel Structure: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Lajdpfxsw Tpqwj Aglsi Electrical System: * Electrical system in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front distribution board with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Entire steel structure is automatically shot-blasted after welding using a blast wheel system * Second blasting with corundum for optimum coating adhesion * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for maximum corrosion protection * Final topcoat with 2 layers of 2K paint, single-color, RAL 3002 Carmine Red, according to RAL System 841GL * Wheel rims in silver * Rear end metallized and in RAL 901

Durumu: yeni, toplam ağırlık: 49.500 kg, dingil konfigürasyonu: 3 dingil, Üretim yılı: 2025, 3-axle MULTIMAX *PLUS low bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h legal Gross vehicle weight: 49,500 kg 31,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin turning radius to rear approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: * Loading platform width approx.: 2,540 mm Load height at max. payload approx.: 890 mm Suspension stroke approx.: -55/+145 mm Axle spacing: 1,360 mm *Gross weight dependent on fifth wheel load: Yes Special permit required if country-specific regulations are exceeded. Technical Description Gooseneck: Gooseneck in SNT design to optimize loading platform length, length approx. 3,900 mm, rear with bevel approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4x2 and 6x2. Loading platform: Loading platform, length approx. 9,600 mm with rear bevel approx. 900 mm x 6°. Loading platform behind gooseneck hydraulically liftable and lowerable, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating surface. Hydraulically foldable ramp tips. Ramps are individually hydraulically adjustable approx. 235 mm outward and approx. 365 mm inward. Maximum load and approach angle as per technical data sheet: C470319 Maximum ramp angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift and lower valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF dual tyres. Manufacturer at our discretion. Load index 143/141J (144/144F) Brake system: WABCO EBS-E braking system according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" configuration according to EU regulations. (ASS 3) Metallisation: Complete HRM metallisation (High Resistance Metallisation). Entire steel structure shot-blasted, then hot-dip refined with ZINACOR 850 (zinc 85% - alu 15%). Painting 6-coat final treatment: Whole steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion promoter. Topcoat with 2 layers of 2-component (acrylic) paint, single-color to RAL palette as chosen, followed by sealing the cavities with special wax. Rims in silver. Multi-color and custom painting available at extra charge. Steel construction: High-strength fine-grained steel construction. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa). Welders certified to DIN EN 287-1. MAG welding process per EN ISO 4063. Shielding gas M21 per EN ISO 14175. Laodpjizu Ntsfx Aglei Front wall made of steel, removable, approx. 400 mm high. Connection panel for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. 24N connection as per ISO-1185 24S connection as per ISO-3731 15-pin connection as per ISO-12098 If your pin assignment differs from the ISO standard, please inform us. "Anderson" socket on the front connection panel. Rema 78051-00 & Amp. 150 V. Cable for electric-hydraulic unit and/or electric winch (

Durumu: yeni, azami yük ağırlığı: 90.700 kg, toplam ağırlık: 126.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.850 mm, Donanım: ABS, You can find our complete inventory of immediately and shortly available vehicles on our website. Excerpt from the equipment list. Complete specification available on request. Gooseneck: Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. For tractor units: 6 x 4 or 8 x 4 3-axle compact front bogie: * Hook coupling at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Low bed: * ATX-A low bed with telescoping longitudinal beams in low-floor design with fixed hardwood floor, approx. 50 mm thick * Equipped with drive-over bridge hooks at the front and bolt-lug coupling at the rear * Base width: approx. 2,850 mm, length: approx. 7,150 mm, beam height: approx. 330 mm, beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance of approx. 150 mm 5-axle rear bogie: * Mechanical bolt-lug coupling for mounting a low bed at the front, end cross member at the rear * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendulum axle 3-axle front bogie: * PENDULUM AXLE, all axles hydro-mechanically steered * Hose rupture valve on the axle equalizer cylinder with automatic RESET function * Hydraulic cylinder with shut-off valves and positioning pins for safety in raised position * Final painting of axles with two coats 2K paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x as per manufacturer's choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDULUM AXLE, all axles hydro-mechanically steered * Hose rupture valve on the axle equalizer cylinder with automatic RESET function * Hydraulic cylinder with shut-off valves and positioning pins for safety in raised position * Final painting of axles with two coats 2K paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x as per manufacturer's choice (M+S) 285/70 R19.5, load index 150/148J Paint finish: * HRM metallisation of the entire chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure maximum corrosion protection * Final coat with two layers of 2K topcoat, single color in RAL 3002 Carmine Red, according to the RAL 841GL system Includes accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU side walls and rear wall for the gooseneck, approx. 400 mm high, anodized version * 3.5" king pin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * Front bogie with a separate air connection for pneumatic tools * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for the installation of bolted container positions for either 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Brackets on the outer beams of the loading platform for attaching foldable extensions * One 7-pin socket left and right, front and rear, on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control for rear axle steering Ledpfew Tgp Dox Agloai * Rear bogie with trough * 2 LED reversing lights mounted on the rear plate * European reflective signs (red-yellow) at the rear * One mudflap at the rear * One LED beacon with bracket left and right on the end cross member * Two INOX toolboxes 855 x 340 x 390 mm mounted left and right on the gooseneck * 1-cycle

Durumu: yeni, azami yük ağırlığı: 50.400 kg, toplam ağırlık: 65.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.540 mm, Donanım: ABS, You will find our complete range of vehicles with immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. GOOSENECK * Gooseneck in SNT design to optimize the loading platform length, approx. 3,700 mm long, rear taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with sockets * 3 kW electric-hydraulic power unit for controlling hydraulic functions (except hydraulic winches) * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized * One removable aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm solid hardwood floor above the gooseneck, over the kingpin with checker plate covering * 2" kingpin * Socket at the rear of the gooseneck for aluminum loading ramps * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) LOADING AREA * Extendable loading area design, approx. 8,800 mm long, with rear taper approx. 500 mm x 10° * A recess in the loading platform and into the taper for accepting the excavator bucket arm, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, 1st axle steering, all other axles hydro-mechanically forced-steered * 1st axle with electric-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with lifting and lowering valve * Tires: 235/75 R 17.5 3PMSF, twin mounting * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B – static test load: approx. 50,000 kg * Continuous hardwood flooring approx. 50 mm thick on the loading area and interrupted between axles (increases friction coefficient) * 1 intermediate platform, approx. 300 mm wide, for the extension tube with large cross-section * Extendable galvanised widenings, approx. 230 mm per side (without wooden planks) * Wheel recesses with 15 x 15 mm square climbing bars in front of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening inserts * Aluminum elements lockable on the extension tubes of the widenings * Widenable U-profiles for inserting the aluminum covers: - on the fixed section behind the gooseneck - on the intermediate platform - on the extendable loading area * Wheel recesses with 15 x 15 mm square climbing bars between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening inserts * Aluminum elements lockable on the extension tubes of the widenings * 1 pair of mechanical rear supports * Remote steering from both the front and rear via cable remote control, with axle single-track control, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-part steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm long, approx. 900 mm wide * Hydraulically foldable ramp tips * Ramps can be hydraulically shifted approx. 235 mm outward and approx. 215 mm inward individually Laedpfxotx Nwnj Aglsi * Super Grip rubber flooring approx. 25 mm and steel deck approx. 5 mm as additional

Durumu: yeni, azami yük ağırlığı: 35.060 kg, toplam ağırlık: 45.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.500 mm, toplam genişlik: 2.540 mm, Donanım: ABS, Our complete inventory of vehicles that are available immediately or at short notice can be found on our website. Laodpfxowx Dc Hs Aglji Excerpt from the equipment. Full specification available upon request. GOOSENECK * Gooseneck designed as a loading platform with aluminum checker plate covering * Hydraulic lifting arm with approx. -280/+250 mm lifting and lowering range * Two king pin positions at approx. 2,300 mm and approx. 2,000 mm * Suitable for tractor units: 4 x 2, 6 x 2 or 6 x 4 * 2-inch king pin * 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) * ASPÖCK-UNIBOX at the front connector strip with 24N, 24S & 15-pin sockets, 24N connection as per ISO-1185, 24S connection as per ISO-3731 * 15-pin connection as per ISO-12098 * Yellow-red air couplings at the front connector strip * Lighting for the operation of the gooseneck, suspension, and hydraulic tensioning with on/off switch * Boom for suspending supply lines on the front end of the gooseneck * Operation of all work lights in the gooseneck area via switches on the gooseneck LOADING AREA * Loading chamber approx. 9,500 mm long, fitted with lower angle profiles to accommodate loading pallets (distance king pin to center of axle assembly approx. 8,000 mm) * BPW stub axles with drum brakes and independent wheel suspension, hydraulic axle compensation with raising and lowering facility * Tyres: 385/65 R 22.5 (M+S) * Mechanical drop-leg supports for approx. 48,000 kg support load * Boarding ladder mounted front right with 2 plug-in grab poles * Removable full fairing on both sides ahead of the axle assembly * WABCO Roll Stability Support (RSS) * 9 pairs of lashing rings on the longitudinal beams (LC 6,300 daN) * Grating support flush with height between the guide rails of the load securing devices on the longitudinal beams * First and last axle left and right can be lifted manually * Toolboxes behind the axle assembly left and right, splash-proof * Rear end chamfered for easier insertion of loading pallets * Lashing eyes at the rear cross member for mechanical tensioning * Rear door with cross bracing, hinged on the left, hydraulically locked on the right, and can be secured horizontally at 90°, 105°, and 270° * Underrun protection, foldable upwards for transporting up to 4 empty standard pallets * Number plate holder with lighting on the rear door * 7-pin socket at the rear cross member * Electro-hydraulic unit for operating the hydraulic functions (without installation in the tractor unit) * TPMS tire pressure monitoring sensors on all wheels including spares * Indicator lamps for vehicle nominal ride height in the operator area * 1 odometer mounted on the left * 2 axle load gauges mounted on the left side including axle load diagram * 2 rubber buffers at the front of the loading channel as stops for loading pallets * Hydraulic preinstallation including control for mounting 4 pairs of our hydraulic load securing devices * 1 spare wheel holder, right-hand side in direction of travel * EU reflector at the rear * Acoustic warning signal when reversing * Round NATO socket at the front connector strip (Maeler & Kaege VG 96 917) BRAKE SYSTEM: * WABCO EBS brake system compliant with EU regulations. WITHOUT connecting cable to the tractor unit LIGHTING SYSTEM * 24-volt lighting system in ASPÖCK-NORDIK full LED version as per EU requirements (ASS 3) SURFACE TREATMENT HRM metallization